From: Robert Marko Date: Tue, 30 Jun 2020 16:07:50 +0000 (+0200) Subject: ipq40xx: add support for Wallystech DR40x9 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=eb564690c995b284204aa762c0f77f3064419a9c;p=openwrt%2Fstaging%2Fblocktrron.git ipq40xx: add support for Wallystech DR40x9 Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko Signed-off-by: Koen Vandeputte --- diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 846032c96f..f3bf1185f8 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -54,6 +54,7 @@ ALLWIFIBOARDS:= \ redmi_ax6 \ sony_ncp-hg100-cellular \ teltonika_rutx \ + wallys_dr40x9 \ xiaomi_ax3600 \ xiaomi_ax9000 \ zte_mf18a \ @@ -158,6 +159,7 @@ $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2)) $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6)) $(eval $(call generate-ipq-wifi-package,sony_ncp-hg100-cellular,Sony NCP-HG100/Cellular)) $(eval $(call generate-ipq-wifi-package,teltonika_rutx,Teltonika RUTX)) +$(eval $(call generate-ipq-wifi-package,wallys_dr40x9,Wallys DR40X9)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax3600,Xiaomi AX3600)) $(eval $(call generate-ipq-wifi-package,xiaomi_ax9000,Xiaomi AX9000)) $(eval $(call generate-ipq-wifi-package,zte_mf18a,ZTE MF18A)) diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 3625938e38..37b9ca268b 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -39,6 +39,7 @@ ipq40xx_setup_interfaces() mikrotik,cap-ac|\ netgear,wac510|\ sony,ncp-hg100-cellular|\ + wallys,dr40x9|\ zte,mf18a|\ zte,mf289f) ucidef_set_interfaces_lan_wan "lan" "wan" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches index 4918e2ccc1..f76fe9402d 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ipq40xx/base-files/etc/board.d/03_gpio_switches @@ -32,6 +32,9 @@ mikrotik,hap-ac3-lte6-kit) sony,ncp-hg100-cellular) ucidef_add_gpio_switch "uart_dbgcon_en" "debug console enable" "427" "1" ;; +wallys,dr40x9) + ucidef_add_gpio_switch "sim_card_select" "SIM card select" "423" "0" + ;; zte,mf286d|\ zte,mf289f) ucidef_add_gpio_switch "power_btn_block" "Power button blocker" "421" "0" diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 2012213a56..988921fa8c 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -119,7 +119,8 @@ platform_do_upgrade() { netgear,wac510 |\ p2w,r619ac-64m |\ p2w,r619ac-128m |\ - qxwlan,e2600ac-c2) + qxwlan,e2600ac-c2 |\ + wallys,dr40x9) nand_do_upgrade "$1" ;; glinet,gl-b2200) diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts new file mode 100644 index 0000000000..b90b6b28c3 --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq40x9-dr40x9.dts @@ -0,0 +1,422 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Wallystech DR40X9"; + compatible = "wallys,dr40x9"; + + chosen { + bootargs-append = " ubi.mtd=ubi root=/dev/ubiblock0_1"; + }; + + soc { + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + status = "okay"; + + /* select hostmode */ + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + wlan2g { + label = "dr4029:green:wlan2g"; + gpios = <&tlmm 32 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "dr4029:green:wlan5g"; + gpios = <&tlmm 50 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan2g-strength { + label = "dr4029:green:wlan2g-strength"; + gpios = <&tlmm 36 GPIO_ACTIVE_LOW>; + }; + + wlan5g-strength { + label = "dr4029:green:wlan5g-strength"; + gpios = <&tlmm 39 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_1 { + pins = "gpio6"; + function = "mdio"; + bias-pull-up; + }; + mux_2 { + pins = "gpio7"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial0_pins: serial0_pinmux { + mux { + pins = "gpio16", "gpio17"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + serial1_pins: serial1_pinmux { + mux { + pins = "gpio8", "gpio9"; + function = "blsp_uart1"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio13", "gpio14", "gpio15"; + drive-strength = <12>; + bias-disable; + }; + pinmux_cs { + function = "gpio"; + pins = "gpio12"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + nand_pins: nand_pins { + pullups { + pins = "gpio52", "gpio53", "gpio58", "gpio59"; + function = "qpic"; + bias-pull-up; + }; + + pulldowns { + pins = "gpio54", "gpio55", "gpio56", "gpio57", + "gpio60", "gpio62", "gpio63", "gpio64", + "gpio65", "gpio66", "gpio67", "gpio68", + "gpio69"; + function = "qpic"; + bias-pull-down; + }; + }; + + sd_pins: sd_pins { + pinmux { + function = "sdio"; + pins = "gpio23", "gpio24", "gpio25", "gpio26", + "gpio28", "gpio29", "gpio30", "gpio31"; + drive-strength = <10>; + }; + pinmux_sd_clk { + function = "sdio"; + pins = "gpio27"; + drive-strength = <16>; + }; + pinmux_sd7 { + function = "sdio"; + pins = "gpio32"; + drive-strength = <10>; + bias-disable; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + + cs-gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + reg = <0>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition0@0 { + label = "0:SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition1@40000 { + label = "0:MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition2@60000 { + label = "0:QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition3@c0000 { + label = "0:CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition4@d0000 { + label = "0:DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition5@e0000 { + label = "0:APPSBLENV"; /* uboot env */ + reg = <0x000e0000 0x00010000>; + read-only; + }; + + partition6@f0000 { + label = "0:APPSBL"; /* uboot */ + reg = <0x000f0000 0x00080000>; + read-only; + }; + + partition7@170000 { + label = "0:ART"; + reg = <0x00170000 0x00010000>; + read-only; + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + precal_art_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + + precal_art_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + + macaddr_art_0: mac-address@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_6: mac-address@6 { + reg = <0x6 0x6>; + }; + + macaddr_art_1006: mac-address@1006 { + reg = <0x1006 0x6>; + }; + + macaddr_art_5006: mac-address@5006 { + reg = <0x5006 0x6>; + }; + + }; + + partition8@180000 { + label = "0:CONFIG"; + reg = <0x00180000 0x00010000>; + read-only; + }; + }; + }; +}; + +&qpic_bam { + status = "okay"; +}; + +&nand { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "ubi"; + reg = <0x00000000 0x04000000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + pinctrl-0 = <&serial0_pins>; + pinctrl-names = "default"; +}; + +&blsp1_uart2 { + status = "okay"; + pinctrl-0 = <&serial1_pins>; + pinctrl-names = "default"; +}; + +&crypto { + status = "okay"; +}; + +&cryptobam { + num-channels = <4>; + qcom,num-ees = <2>; + status = "okay"; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 41 GPIO_ACTIVE_LOW>; + reset-delay-us = <2000>; +}; + +&pcie0 { + status = "okay"; + + perst-gpio = <&tlmm 38 GPIO_ACTIVE_LOW>; + wake-gpio = <&tlmm 40 GPIO_ACTIVE_LOW>; + + /* Unpolulated slot */ + bridge@0,0 { + reg = <0x00000000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + ranges; + }; +}; + +&vqmmc { + status = "okay"; +}; + +&sdhci { + status = "okay"; + pinctrl-0 = <&sd_pins>; + pinctrl-names = "default"; + cd-gpios = <&tlmm 22 GPIO_ACTIVE_LOW>; + vqmmc-supply = <&vqmmc>; +}; + +&gmac { + status = "okay"; +}; + +&switch { + status = "okay"; +}; + +&swport4 { + status = "okay"; + label = "wan"; + nvmem-cells = <&macaddr_art_0>; + nvmem-cell-names = "mac-address"; +}; + +&swport5 { + status = "okay"; + label = "lan"; + nvmem-cells = <&macaddr_art_6>; + nvmem-cell-names = "mac-address"; +}; + +&wifi0 { + status = "okay"; + nvmem-cells = <&precal_art_1000>, <&macaddr_art_1006>; + nvmem-cell-names = "pre-calibration", "mac-address"; + qcom,ath10k-calibration-variant = "Wallys-DR40X9"; +}; + +&wifi1 { + status = "okay"; + nvmem-cell-names = "pre-calibration", "mac-address"; + nvmem-cells = <&precal_art_5000>, <&macaddr_art_5006>; + qcom,ath10k-calibration-variant = "Wallys-DR40X9"; +}; + +&usb2 { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index 68a45dbf9b..48514b8841 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -1122,6 +1122,19 @@ endef # Missing DSA Setup #TARGET_DEVICES += unielec_u4019-32m +define Device/wallys_dr40x9 + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_VENDOR := Wallys + DEVICE_MODEL := DR40X9 + SOC := qcom-ipq40x9 + DEVICE_DTS_CONFIG := config@ap.dk07.1-c1 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_PACKAGES := ipq-wifi-wallys_dr40x9 +endef +TARGET_DEVICES += wallys_dr40x9 + define Device/zte_mf18a $(call Device/FitImage) DEVICE_VENDOR := ZTE