From: Pawel Dembicki Date: Wed, 24 Oct 2018 12:06:35 +0000 (+0200) Subject: ramips: add support for D-Link DWR-118-A1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e9a9b7d1ed76c88e097d5bc4dabf38735312558b;p=openwrt%2Fstaging%2Fnbd.git ramips: add support for D-Link DWR-118-A1 The DWR-118-A1 Wireless Router is based on the MT7620A SoC. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 1x 802.11bgn radio - 1x 802.11ac radio (MT7610EN) - 3x 10/100 Mbps Ethernet (3 LAN) - 2x 10/100/1000 Mbps ICPlus IP1001 Ethernet PHY (1 WAN AND 1 LAN) - 1x internal, non-detachable antenna - 2x external, non-detachable antennas - 1x USB 2.0 - UART (J1) header on PCB (57600 8n1) - 7x LED (5x GPIO-controlled), 2x button - JBOOT bootloader Known issues: - WIFI 5G LED not working - flash is very slow The status led has been assigned to the dwr-118-a1:green:internet led. At the end of the boot it is switched off and is available for other operation. Work correctly also during sysupgrade operation. Installation: Apply factory image via http web-gui or JBOOT recovery page How to revert to OEM firmware: - push the reset button and turn on the power. Wait until LED start blinking (~10sec.) - upload original factory image via JBOOT http (IP: 192.168.123.254) Signed-off-by: Pawel Dembicki --- diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index b2c69d4b59..f8c4b05b9a 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -114,6 +114,11 @@ dlink,dwr-116-a1|\ mzk-ex300np) set_wifi_led "$boardname:green:wifi" ;; +dlink,dwr-118-a1) + ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x1f" + ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x20" + set_wifi_led "$boardname:green:wlan2g" "wlan1" + ;; dlink,dwr-118-a2) ucidef_set_led_switch "lan" "lan" "$boardname:green:lan" "switch0" "0x0e" ucidef_set_led_switch "wan" "wan" "$boardname:green:wan" "switch0" "0x01" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 3af836a6f3..c207b7cad4 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -162,6 +162,10 @@ ramips_setup_interfaces() wrh-300cr) ucidef_set_interface_lan "eth0" ;; + dlink,dwr-118-a1) + ucidef_add_switch "switch0" \ + "1:lan:2" "2:lan:3" "3:lan:1" "4:lan:0" "5:wan" "6@eth0" + ;; dlink,dwr-118-a2) ucidef_add_switch "switch0" \ "1:lan:2" "2:lan:1" "3:lan:3" "4:lan" "0:wan" "6@eth0" @@ -475,6 +479,7 @@ ramips_setup_macs() wan_mac=$(mtd_get_mac_ascii factory wanmac) ;; dlink,dwr-116-a1|\ + dlink,dwr-118-a1|\ dlink,dwr-118-a2|\ dlink,dwr-921-c1|\ lava,lr-25g001) diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom index aee446d156..1d9de2d503 100644 --- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom +++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom @@ -55,6 +55,7 @@ case "$FIRMWARE" in "soc_wmac.eeprom") case $board in dlink,dwr-116-a1|\ + dlink,dwr-118-a1|\ dlink,dwr-118-a2|\ dlink,dwr-921-c1|\ lava,lr-25g001) diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 120cf8322a..8c7b818221 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -296,6 +296,7 @@ platform_check_image() { return 0 ;; dlink,dwr-116-a1|\ + dlink,dwr-118-a1|\ dlink,dwr-118-a2|\ dlink,dwr-921-c1|\ dwr-512-b|\ diff --git a/target/linux/ramips/dts/DWR-118-A1.dts b/target/linux/ramips/dts/DWR-118-A1.dts new file mode 100644 index 0000000000..ab88553a05 --- /dev/null +++ b/target/linux/ramips/dts/DWR-118-A1.dts @@ -0,0 +1,189 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7620a.dtsi" + +#include +#include + +/ { + compatible = "dlink,dwr-118-a1", "ralink,mt7620a-soc"; + model = "D-Link DWR-118 A1"; + + aliases { + led-boot = &led_internet; + led-failsafe = &led_internet; + led-upgrade = &led_internet; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + wps { + label = "wps"; + gpios = <&gpio0 12 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + wan { + label = "dwr-118-a1:green:wan"; + gpios = <&gpio3 0 GPIO_ACTIVE_LOW>; + }; + + led_internet: internet { + label = "dwr-118-a1:green:internet"; + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; + }; + + lan { + label = "dwr-118-a1:green:lan"; + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + }; + + wlan2g { + label = "dwr-118-a1:green:wlan2g"; + gpios = <&gpio1 15 GPIO_ACTIVE_LOW>; + }; + + usb { + label = "dwr-118-a1:green:usb"; + gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + trigger-sources = <&ohci_port1>, <&ehci_port1>; + linux,default-trigger = "usbport"; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + usb { + gpio-export,name = "usb"; + gpio-export,output = <0>; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&gpio1 { + status = "okay"; +}; + +&gpio2 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "jboot"; + reg = <0x0 0x10000>; + read-only; + }; + + partition@10000 { + compatible = "amit,jimage"; + label = "firmware"; + reg = <0x10000 0xfe0000>; + }; + + config: partition@ff0000 { + label = "config"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; + +&pinctrl { + state_default: pinctrl0 { + default { + ralink,group = "ephy", "uartf", "spi refclk", "wled"; + ralink,function = "gpio"; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + reg = <0x0000 0 0 0 0>; + mtd-mac-address = <&config 0xe496>; + mtd-mac-address-increment = <(2)>; + mediatek,mtd-eeprom = <&config 0xe083>; + }; +}; + +ðernet { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&rgmii1_pins &rgmii2_pins &mdio_pins>; + + port@4 { + status = "okay"; + phy-handle = <&phy4>; + phy-mode = "rgmii"; + }; + + port@5 { + status = "okay"; + phy-handle = <&phy5>; + phy-mode = "rgmii"; + }; + + mdio-bus { + status = "okay"; + + phy4: ethernet-phy@4 { + reg = <4>; + phy-mode = "rgmii-rxid"; + }; + + phy5: ethernet-phy@5 { + reg = <5>; + phy-mode = "rgmii-rxid"; + }; + }; +}; + +&gsw { + mediatek,port4 = "gmac"; +}; diff --git a/target/linux/ramips/image/mt7620.mk b/target/linux/ramips/image/mt7620.mk index c526f9681e..143d33e3c8 100644 --- a/target/linux/ramips/image/mt7620.mk +++ b/target/linux/ramips/image/mt7620.mk @@ -176,6 +176,20 @@ define Device/dlink_dwr-116-a1 endef TARGET_DEVICES += dlink_dwr-116-a1 +define Device/dlink_dwr-118-a1 + DTS := DWR-118-A1 + DEVICE_TITLE := D-Link DWR-118 A1 + DEVICE_PACKAGES := kmod-usb2 jboot-tools kmod-mt76x0e + DLINK_ROM_ID := DLK6E3811001 + DLINK_FAMILY_MEMBER := 0x6E38 + DLINK_FIRMWARE_SIZE := 0xFE0000 + KERNEL := $(KERNEL_DTB) + IMAGES += factory.bin + IMAGE/sysupgrade.bin := mkdlinkfw | pad-rootfs | append-metadata + IMAGE/factory.bin := mkdlinkfw | pad-rootfs | mkdlinkfw-factory +endef +TARGET_DEVICES += dlink_dwr-118-a1 + define Device/dlink_dwr-118-a2 DTS := DWR-118-A2 DEVICE_TITLE := D-Link DWR-118 A2