From: Daniel González Cabanelas Date: Thu, 8 Jun 2023 22:09:33 +0000 (+0200) Subject: bmips: add support for Observa VH4032N X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e7a0b61397799e1e15574ad7a4fa82aeb8b99e04;p=openwrt%2Fstaging%2Fblogic.git bmips: add support for Observa VH4032N The Observa VH4032N is an xDSL wifi router with a vertical white casing and two internal antennas connected via UFL. Hardware: - SoC: Broadcom BCM6368 - CPU: dual core BMIPS4350 V3.1 @400MHz - RAM: 128 MB DDR - Flash: 32 MB parallel NOR - Ethernet LAN: 4x 100Mbit - Wifi 2.4/5 GHz: onboard Broadcom BCM43222 802.11abgn - USB: 3x 2.0 - Buttons: 2x, 1 reset - LEDs: 8x, blue and red - UART: 1x Installation via OEM web UI: 1. Use the admin credentials to login via web UI 2. Go to Managament->Update firmware and select the OpenWrt CFE firmware 3. Press "Update Firmware" button and wait some minutes until it finish Signed-off-by: Daniel González Cabanelas --- diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds new file mode 100644 index 000000000000..ab797568b7fd --- /dev/null +++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/01_leds @@ -0,0 +1,17 @@ +# SPDX-License-Identifier: GPL-2.0-or-later + +. /lib/functions/leds.sh +. /lib/functions/uci-defaults.sh + +board_config_update + +case "$(board_name)" in +observa,vh4032n) + ucidef_set_led_usbport "usb1" "USB1" "blue:hspa" "usb1-port1" "usb2-port1" + ucidef_set_led_usbport "usb2" "USB2" "red:hspa" "1-2-port1" "1-2-port2" + ;; +esac + +board_config_flush + +exit 0 diff --git a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network index 14d6e56dd1cf..1064b80fba16 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network +++ b/target/linux/bmips/bcm6368/base-files/etc/board.d/02_network @@ -5,7 +5,8 @@ board_config_update case "$(board_name)" in -comtrend,vr-3025u) +comtrend,vr-3025u |\ +observa,vh4032n) ucidef_set_bridge_device switch ucidef_set_interface_lan "lan1 lan2 lan3 lan4" ;; diff --git a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc index c66e4169fdda..d4ff723d1421 100644 --- a/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc +++ b/target/linux/bmips/bcm6368/base-files/etc/uci-defaults/09_fix_crc @@ -3,7 +3,8 @@ . /lib/functions.sh case "$(board_name)" in -comtrend,vr-3025u) +comtrend,vr-3025u |\ +observa,vh4032n) mtd fixtrx firmware ;; esac diff --git a/target/linux/bmips/dts/bcm6368-observa-vh4032n.dts b/target/linux/bmips/dts/bcm6368-observa-vh4032n.dts new file mode 100644 index 000000000000..4a4cca0982c4 --- /dev/null +++ b/target/linux/bmips/dts/bcm6368-observa-vh4032n.dts @@ -0,0 +1,233 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "bcm6368.dtsi" + +/ { + model = "Observa VH4032N"; + compatible = "observa,vh4032n", "brcm,bcm6368"; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_red; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + reset { + label = "reset"; + gpios = <&gpio 34 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + rfkill { + label = "rfkill"; + gpios = <&gpio 35 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led@2 { + label = "blue:dsl"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + + led@5 { + label = "red:dsl"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + led@11 { + label = "blue:hspa"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + led@12 { + label = "red:hspa"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + led_power_blue: led@22 { + label = "blue:power"; + gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_power_red: led@24 { + label = "red:power"; + gpios = <&gpio 24 GPIO_ACTIVE_HIGH>; + }; + + led@25 { + label = "blue:voice"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + }; + + led@26 { + label = "red:voice"; + gpios = <&gpio 26 GPIO_ACTIVE_LOW>; + }; + }; + + bcm43222-sprom { + compatible = "brcm,ssb-sprom"; + + pci-bus = <0>; + pci-dev = <1>; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; + mac-address-increment = <1>; + + brcm,sprom = "brcm/bcm43222-sprom.bin"; + brcm,sprom-fixups = <2 0x04d2>, <4 0x4350>, + <65 0x1300>, <68 0x0402>, + <70 0x0090>, <71 0x4c19>, + <72 0x2345>, <87 0x0315>, + <88 0x0315>, <96 0x2048>, + <97 0xfed7>, <98 0x15a6>, + <99 0xfaee>, <100 0x3e3a>, + <101 0x3a36>, <102 0xff7f>, + <103 0x11b9>, <104 0xfc53>, + <105 0xffe6>, <106 0xfdd2>, + <107 0xfe49>, <108 0xff6a>, + <109 0x136e>, <110 0xfbed>, + <111 0x0000>, <112 0x2048>, + <113 0xfee2>, <114 0x15e5>, + <115 0xfaed>, <116 0x3e3a>, + <117 0x3a36>, <118 0xffc8>, + <119 0x12b8>, <120 0xfca1>, + <121 0xff9b>, <122 0x122a>, + <123 0xfcc8>, <124 0xff95>, + <125 0x146b>, <126 0xfbba>, + <127 0x0000>, <161 0x0000>, + <162 0x0000>, <169 0x0000>, + <170 0x0000>, <171 0x0000>, + <172 0x0000>, <173 0x0000>, + <174 0x0000>, <175 0x0000>, + <176 0x0000>, <219 0x1108>; + }; +}; + +&ehci { + status = "okay"; +}; + +ðernet { + status = "okay"; + + nvmem-cells = <&macaddr_cfe_6a0>; + nvmem-cell-names = "mac-address"; +}; + +&gpio { + usb_hub_reset { + gpio-hog; + gpios = <27 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-hub-reset-gpio"; + }; +}; + +&ohci { + status = "okay"; +}; + +&pci { + status = "okay"; +}; + +&pflash { + status = "okay"; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + cfe: partition@0 { + label = "CFE"; + reg = <0x0000000 0x0020000>; + read-only; + }; + + partition@20000 { + compatible = "brcm,bcm963xx-imagetag"; + label = "firmware"; + reg = <0x0020000 0x1fc0000>; + }; + + partition@1fe0000 { + label = "nvram"; + reg = <0x1fe0000 0x020000>; + }; + }; +}; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ephy0_led &pinctrl_ephy1_led + &pinctrl_ephy2_led &pinctrl_ephy3_led>; +}; + +&switch0 { + ports { + port@0 { + reg = <0>; + label = "lan4"; + + phy-handle = <&phy1>; + phy-mode = "mii"; + }; + + port@1 { + reg = <1>; + label = "lan3"; + + phy-handle = <&phy2>; + phy-mode = "mii"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + + phy-handle = <&phy3>; + phy-mode = "mii"; + }; + + port@3 { + reg = <3>; + label = "lan1"; + + phy-handle = <&phy4>; + phy-mode = "mii"; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&usbh { + status = "okay"; +}; + +&cfe { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_cfe_6a0: macaddr@6a0 { + reg = <0x6a0 0x6>; + }; +}; diff --git a/target/linux/bmips/image/bcm6368.mk b/target/linux/bmips/image/bcm6368.mk index 268b68dd7c30..e3aa40d404c0 100644 --- a/target/linux/bmips/image/bcm6368.mk +++ b/target/linux/bmips/image/bcm6368.mk @@ -13,3 +13,18 @@ define Device/comtrend_vr-3025u kmod-leds-gpio endef TARGET_DEVICES += comtrend_vr-3025u + +define Device/observa_vh4032n + $(Device/bcm63xx-cfe) + DEVICE_VENDOR := Observa + DEVICE_MODEL := VH4032N + IMAGES += sysupgrade.bin + CFE_BOARD_ID := 96368VVW + CHIP_ID := 6368 + BLOCKSIZE := 0x20000 + FLASH_MB := 32 + DEVICE_PACKAGES += $(USB2_PACKAGES) \ + $(B43_PACKAGES) broadcom-43222-sprom \ + kmod-leds-gpio +endef +TARGET_DEVICES += observa_vh4032n