From: Chukun Pan Date: Sun, 21 May 2023 15:00:16 +0000 (+0800) Subject: mediatek: filogic: add H3C Magic NX30 Pro support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e78d1a06c8a47be9ea5a306bfb43f3d7ceb89646;p=openwrt%2Fstaging%2Fnbd.git mediatek: filogic: add H3C Magic NX30 Pro support Hardware specification: SoC: MediaTek MT7981B 2x A53 Flash: W25N01GVZEIG 128MB RAM: NT5CB128M16JR-FL 256MB Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531AE WiFi: MediaTek MT7976C Button: Reset, WPS Power: DC 12V 1A Flash instructions: 1. PC run command: "telnet 192.168.124.1 99" Username: H3C, password is the web login password of the router. 2. Download preloader.bin and bl31-uboot.fip 3. PC run command: "python3 -m http.server 80" 4. Download files in the telnet window: "wget http://192.168.124.xx/xxx.bin" Replace xx with your PC's IP and the preloader.bin and bl31-uboot.fip. 5. Flushing openwrt's uboot: "mtd write xxx-preloader.bin BL2" "mtd write xxx-bl31-uboot.fip FIP" 6. Connect to the router via the Lan port, set a static ip of your PC. (ip 192.168.1.254, gateway 192.168.1.1) 7. Download initramfs image, reboot router, waiting for tftp recovery to complete. 8. After openwrt boots up, perform sysupgrade. Note: 1. The u-boot-env partition on mtd is empty, OEM stores their env on ubi:u-boot-env. 2. Back up all mtd partitions before flashing. Signed-off-by: Chukun Pan --- diff --git a/target/linux/mediatek/dts/mt7981b-h3c-magic-nx30-pro.dts b/target/linux/mediatek/dts/mt7981b-h3c-magic-nx30-pro.dts new file mode 100644 index 0000000000..358365adba --- /dev/null +++ b/target/linux/mediatek/dts/mt7981b-h3c-magic-nx30-pro.dts @@ -0,0 +1,239 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include +#include + +#include "mt7981.dtsi" + +/ { + model = "H3C Magic NX30 Pro"; + compatible = "h3c,magic-nx30-pro", "mediatek,mt7981"; + + aliases { + serial0 = &uart0; + led-boot = &led_status_green; + led-failsafe = &led_status_red; + led-running = &led_status_green; + led-upgrade = &led_status_red; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_green: green { + label = "green:status"; + gpios = <&pio 4 GPIO_ACTIVE_LOW>; + }; + + led_status_red: red { + label = "red:status"; + gpios = <&pio 5 GPIO_ACTIVE_LOW>; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + }; +}; + +&mdio_bus { + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + status = "okay"; + + spi_nand@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <52000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x0000000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x0180000 0x0200000>; + read-only; + }; + + partition@380000 { + label = "FIP"; + reg = <0x0380000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x0580000 0x4000000>; + }; + + /* yaffs partition */ + partition@4580000 { + label = "pdt_data"; + reg = <0x4580000 0x0600000>; + read-only; + }; + + /* yaffs partition */ + partition@4b80000 { + label = "pdt_data_1"; + reg = <0x4b80000 0x0600000>; + read-only; + }; + + partition@5180000 { + label = "exp"; + reg = <0x5180000 0x0100000>; + read-only; + }; + + partition@5280000 { + label = "plugin"; + reg = <0x5280000 0x2580000>; + read-only; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + + mediatek,mtd-eeprom = <&factory 0x0>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index c05c5d25e4..6abc81a0b0 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -23,6 +23,9 @@ mediatek_setup_interfaces() glinet,gl-mt3000) ucidef_set_interfaces_lan_wan eth1 eth0 ;; + h3c,magic-nx30-pro) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1 + ;; mediatek,mt7986a-rfb) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan6" "eth1 wan" ;; @@ -72,6 +75,11 @@ mediatek_setup_macs() bananapi,bpi-r3) wan_mac=$(macaddr_add $(cat /sys/class/net/eth0/address) 1) ;; + h3c,magic-nx30-pro) + wan_mac=$(mtd_get_mac_ascii pdt_data_1 ethaddr) + lan_mac=$(macaddr_add "$wan_mac" 1) + label_mac=$wan_mac + ;; mercusys,mr90x-v1) label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0) lan_mac=$label_mac diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 4b7047eec5..ab23b10044 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -32,6 +32,11 @@ case "$board" in [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress ;; + h3c,magic-nx30-pro) + addr=$(mtd_get_mac_ascii pdt_data_1 ethaddr) + [ "$PHYNBR" = "0" ] && macaddr_add $addr 2 > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && macaddr_add $addr 3 > /sys${DEVPATH}/macaddress + ;; mercusys,mr90x-v1) addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 11c2c5c664..186abfa5a8 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -74,6 +74,7 @@ platform_do_upgrade() { CI_UBIPART="ubi0" nand_do_upgrade "$1" ;; + h3c,magic-nx30-pro|\ qihoo,360t7|\ tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index fd83b9d441..2ace305140 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -176,6 +176,31 @@ define Device/glinet_gl-mt3000 endef TARGET_DEVICES += glinet_gl-mt3000 +define Device/h3c_magic-nx30-pro + DEVICE_VENDOR := H3C + DEVICE_MODEL := Magic NX30 Pro + DEVICE_DTS := mt7981b-h3c-magic-nx30-pro + DEVICE_DTS_DIR := ../dts + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_IN_UBI := 1 + UBOOTENV_IN_UBI := 1 + IMAGE_SIZE := 65536k + IMAGES := sysupgrade.itb + KERNEL_INITRAMFS_SUFFIX := -recovery.itb + KERNEL := kernel-bin | gzip + KERNEL_INITRAMFS := kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k + IMAGE/sysupgrade.itb := append-kernel | \ + fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-static-with-rootfs | append-metadata + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware + ARTIFACTS := preloader.bin bl31-uboot.fip + ARTIFACT/preloader.bin := mt7981-bl2 spim-nand-ddr3 + ARTIFACT/bl31-uboot.fip := mt7981-bl31-uboot h3c_magic-nx30-pro +endef +TARGET_DEVICES += h3c_magic-nx30-pro + define Device/netgear_wax220 DEVICE_VENDOR := Netgear DEVICE_MODEL := WAX220