From: Mikhail Zhilkin Date: Sat, 13 May 2023 13:51:45 +0000 (+0000) Subject: mediatek: add support for Mercusys MR90X v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e4fe3097ef6a961874b66932a0ac4be18070630a;p=openwrt%2Fstaging%2Frmilecki.git mediatek: add support for Mercusys MR90X v1 This commit adds support for Mercusys MR90X(EU) v1 router. Device specification -------------------- SoC Type: MediaTek MT7986BLA, Cortex-A53, 64-bit RAM: MediaTek MT7986BLA (512MB) Flash: SPI NAND GigaDevice GD5F1GQ5UEYIGY (128 MB) Ethernet: MediaTek MT7531AE + 2.5GbE MaxLinear GPY211C0VC (SLNW8) Ethernet: 1x2.5Gbe (WAN/LAN 2.5Gbps), 3xGbE (WAN/LAN 1Gbps, LAN1, LAN2) WLAN 2g: MediaTek MT7975N, b/g/n/ax, MIMO 4x4 WLAN 5g: MediaTek MT7975P(N), a/n/ac/ax, MIMO 4x4 LEDs: 1 orange and 1 green status LEDs, 4 green gpio-controlled LEDs on ethernet ports Button: 1 (Reset) USB ports: No Power: 12 VDC, 2 A Connector: Barrel Bootloader: Main U-Boot - U-Boot 2022.01-rc4. Additionally, both UBI slots contain "seconduboot" (also U-Boot 2022.01-rc4) Serial console (UART) --------------------- V +-------+-------+-------+-------+ | +3.3V | GND | TX | RX | +---+---+-------+-------+-------+ | +--- Don't connect The R3 (TX line) and R6 (RX line) are absent on the PCB. You should solder them or solder the jumpers. Installation (UART) ------------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Once inside OpenWrt, set / update env variables: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 5. Run 'sysupgrade -n' with the sysupgrade OpenWrt image Installation (without UART) --------------------------- 1. Login as root via SSH (router IP, port 20001, password - your web interface password) 2. Open for editing /etc/hotplug.d/iface/65-iptv (e.g., using WinSCP and SSH settings from the p.1) 3. Add a newline after "#!/bin/sh": telnetd -l /bin/login.sh 4. Save "65-iptv" file 5. Toggle "IPTV/VLAN Enable" checkbox in the router web interface and save 6. Make sure that telnetd is running: netstat -ltunp | grep 23 7. Login via telnet to router IP, port 23 (no username and password are required) 8 Upload OpenWrt "initramfs-kernel.bin" to the "/tmp" folder of the router (e.g., using WinSCP and SSH settings from the p.1) 9. Stock busybox doesn't contain ubiupdatevol command. Hence, we need to download and upload the full version of busybox to the router. For example, from here: https://github.com/xerta555/Busybox-Binaries/raw/master/busybox-arm64 Upload busybox-arm64 to the /tmp dir of the router and run: in the telnet shell: cd /tmp chmod a+x busybox-arm64 10. Check "initramfs-kernel.bin" size: du -h initramfs-kernel.bin 11. Delete old and create new "kernel" volume with appropriate size (greater than "initramfs-kernel.bin" size): ubirmvol /dev/ubi0 -N kernel ubimkvol /dev/ubi0 -n 1 -N kernel -s 9MiB 12. Write OpenWrt "initramfs-kernel.bin" to the flash: ./busybox-arm64 ubiupdatevol /dev/ubi0_1 /tmp/initramfs-kernel.bin 13. u-boot-env can be empty so lets create it (or overwrite it if it already exists) with the necessary values: fw_setenv baudrate 115200 fw_setenv bootargs "ubi.mtd=ubi0 console=ttyS0,115200n1 loglevel=8 earlycon=uart8250,mmio32,0x11002000 init=/etc/preinit" fw_setenv fdtcontroladdr 5ffc0e70 fw_setenv ipaddr 192.168.1.1 fw_setenv loadaddr 0x46000000 fw_setenv mtdids "spi-nand0=spi-nand0" fw_setenv mtdparts "spi-nand0:2M(boot),1M(u-boot-env),50M(ubi0),50M(ubi1),8M(userconfig),4M(tp_data)" fw_setenv netmask 255.255.255.0 fw_setenv serverip 192.168.1.2 fw_setenv stderr serial@11002000 fw_setenv stdin serial@11002000 fw_setenv stdout serial@11002000 fw_setenv tp_boot_idx 0 14. Reboot to OpenWrt initramfs: reboot 15. Login as root via SSH (IP 192.168.1.1, port 22) 16. Upload OpenWrt sysupgrade.bin image to the /tmp dir of the router 17. Run sysupgrade: sysupgrade -n /tmp/sysupgrade.bin Recovery -------- 1. Press Reset button and power on the router 2. Navigate to U-Boot recovery web server (http://192.168.1.1/) and upload the OEM firmware Recovery (UART) --------------- 1. Place OpenWrt initramfs image on tftp server with IP 192.168.1.2 2. Attach UART, switch on the router and interrupt the boot process by pressing 'Ctrl-C' 3. Load and run OpenWrt initramfs image: tftpboot initramfs-kernel.bin bootm 4. Do what you need (restore partitions from a backup, install OpenWrt etc.) Stock layout ------------ 0x000000000000-0x000000200000 : "boot" 0x000000200000-0x000000300000 : "u-boot-env" 0x000000300000-0x000003500000 : "ubi0" 0x000003500000-0x000006700000 : "ubi1" 0x000006700000-0x000006f00000 : "userconfig" 0x000006f00000-0x000007300000 : "tp_data" ubi0/ubi1 format ---------------- U-Boot at boot checks that all volumes are in place: +-------------------------------+ | Volume Name: uboot Vol ID: 0| | Volume Name: kernel Vol ID: 1| | Volume Name: rootfs Vol ID: 2| +-------------------------------+ MAC addresses ------------- +---------+-------------------+-----------+ | | MAC | Algorithm | +---------+-------------------+-----------+ | label | 00:eb:xx:xx:xx:be | label | | LAN | 00:eb:xx:xx:xx:be | label | | WAN | 00:eb:xx:xx:xx:bf | label+1 | | WLAN 2g | 00:eb:xx:xx:xx:be | label | | WLAN 5g | 00:eb:xx:xx:xx:bd | label-1 | +---------+-------------------+-----------+ label MAC address was found in UBI partition "tp_data", file "default-mac". OEM wireless eeprom is also there (file "MT7986_EEPROM.bin"). Signed-off-by: Mikhail Zhilkin --- diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index 881d0c45011..7918bdacfcd 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -40,6 +40,10 @@ bananapi,bpi-r3) glinet,gl-mt3000) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x80000" "0x20000" ;; +mercusys,mr90x-v1) + local envdev=/dev/mtd$(find_mtd_index "u-boot-env") + ubootenv_add_uci_config "$envdev" "0x0" "0x20000" "0x20000" "1" + ;; netgear,wax220) ubootenv_add_uci_config "/dev/mtd5" "0x0" "0x20000" "0x20000" ;; diff --git a/target/linux/mediatek/dts/mt7986b-mercusys-mr90x-v1.dts b/target/linux/mediatek/dts/mt7986b-mercusys-mr90x-v1.dts new file mode 100644 index 00000000000..8b8858ccef7 --- /dev/null +++ b/target/linux/mediatek/dts/mt7986b-mercusys-mr90x-v1.dts @@ -0,0 +1,276 @@ +// SPDX-License-Identifier: (GL-2.0 OR MIT) + +/dts-v1/; +#include +#include + +#include "mt7986b.dtsi" + +/ { + compatible = "mercusys,mr90x-v1", "mediatek,mt7986b"; + model = "Mercusys MR90X v1"; + + aliases { + serial0 = &uart0; + + led-boot = &led_status_green; + led-failsafe = &led_status_green; + led-running = &led_status_green; + led-upgrade = &led_status_green; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x20000000>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&pio 10 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led-0 { + label = "green:lan2"; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + + led-1 { + label = "green:lan1"; + gpios = <&pio 9 GPIO_ACTIVE_LOW>; + }; + + led-2 { + label = "green:lan0"; + gpios = <&pio 12 GPIO_ACTIVE_LOW>; + }; + + led-3 { + label = "green:wan"; + gpios = <&pio 13 GPIO_ACTIVE_LOW>; + }; + + led-4 { + label = "orange:status"; + gpios = <&pio 16 GPIO_ACTIVE_HIGH>; + }; + + led_status_green: led-5 { + label = "green:status"; + gpios = <&pio 17 GPIO_ACTIVE_HIGH>; + panic-indicator; + }; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-handle = <&phy6>; + phy-mode = "2500base-x"; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mdio { + #address-cells = <1>; + #size-cells = <0>; + + reset-gpios = <&pio 6 GPIO_ACTIVE_LOW>; + reset-delay-us = <1500000>; + reset-post-delay-us = <1000000>; + + /* WAN/LAN 2.5Gbps phy + MaxLinear GPY211C0VC (SLNW8) */ + phy6: phy@6 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <6>; + }; + + switch: switch@0 { + compatible = "mediatek,mt7531"; + reg = <31>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + /* WAN/LAN 1Gbps port */ + port@0 { + reg = <0>; + label = "lan0"; + }; + + /* LAN1 port */ + port@1 { + reg = <1>; + label = "lan1"; + }; + + /* LAN2 port */ + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@6 { + reg = <6>; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&pio { + spi_flash_pins: spi-flash-pins-33-to-38 { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI2_CS", "SPI2_HOLD", "SPI2_WP"; + drive-strength = <8>; + mediatek,pull-up-adv = <0>; /* bias-disable */ + }; + conf-pd { + pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO"; + drive-strength = <8>; + mediatek,pull-down-adv = <0>; /* bias-disable */ + }; + }; + + wf_2g_5g_pins: wf_2g_5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; + + spi_nand_flash: flash@0 { + compatible = "spi-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + + spi-max-frequency = <20000000>; + spi-tx-buswidth = <4>; + spi-rx-buswidth = <4>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot"; + reg = <0x0 0x200000>; + read-only; + }; + + partition@200000 { + label = "u-boot-env"; + reg = <0x200000 0x100000>; + }; + + partition@300000 { + label = "ubi0"; + reg = <0x300000 0x3200000>; + }; + + partition@3500000 { + label = "ubi1"; + reg = <0x3500000 0x3200000>; + read-only; + }; + + partition@6700000 { + label = "userconfig"; + reg = <0x6700000 0x800000>; + read-only; + }; + + partition@6f00000 { + label = "tp_data"; + reg = <0x6f00000 0x400000>; + read-only; + }; + }; + }; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&wf_2g_5g_pins>; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index 0ba825fd2b9..c81bd2cd975 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -9,6 +9,12 @@ case $board in cudy,wr3000-v1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" ;; +mercusys,mr90x-v1) + ucidef_set_led_netdev "lan0" "lan0" "green:lan0" "lan0" "link tx rx" + ucidef_set_led_netdev "lan1" "lan2" "green:lan1" "lan1" "link tx rx" + ucidef_set_led_netdev "lan2" "lan2" "green:lan2" "lan2" "link tx rx" + ucidef_set_led_netdev "wan" "wan" "green:wan" "eth1" "link tx rx" + ;; netgear,wax220) ucidef_set_led_netdev "eth0" "LAN" "green:lan" "eth0" ucidef_set_led_netdev "wlan2g" "WLAN2G" "blue:wlan2g" "phy0-ap0" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index 8803326b279..c05c5d25e46 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -32,6 +32,9 @@ mediatek_setup_interfaces() mediatek,mt7988a-dsa-10g-spim-snand) ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" "eth1 eth2" ;; + mercusys,mr90x-v1) + ucidef_set_interfaces_lan_wan "lan0 lan1 lan2" eth1 + ;; qihoo,360t7) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" wan ;; @@ -69,6 +72,10 @@ mediatek_setup_macs() bananapi,bpi-r3) wan_mac=$(macaddr_add $(cat /sys/class/net/eth0/address) 1) ;; + mercusys,mr90x-v1) + label_mac=$(get_mac_binary "/tmp/tp_data/default-mac" 0) + lan_mac=$label_mac + ;; netgear,wax220) lan_mac=$(mtd_get_mac_ascii u-boot-env mac) label_mac=$lan_mac diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 3969a7bfe47..4b7047eec5e 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -32,6 +32,11 @@ case "$board" in [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress ;; + mercusys,mr90x-v1) + addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) + [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && macaddr_add $addr -1 > /sys${DEVPATH}/macaddress + ;; netgear,wax220) hw_mac_addr=$(mtd_get_mac_ascii u-boot-env mac) [ "$PHYNBR" = "0" ] && macaddr_add $hw_mac_addr 2 > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part new file mode 100644 index 00000000000..819df40d080 --- /dev/null +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/09_mount_cfg_part @@ -0,0 +1,23 @@ +. /lib/functions/system.sh + +mount_ubi_part() { + local part_name="$1" + local mtd_num=$(grep $part_name /proc/mtd | cut -c4) + local ubi_num=$(ubiattach -m $mtd_num | \ + awk -F',' '/UBI device number [0-9]{1,}/{print $1}' | \ + awk '{print $4}') + mkdir /tmp/$part_name + mount -r -t ubifs ubi$ubi_num:$part_name /tmp/$part_name +} + +preinit_mount_cfg_part() { + case $(board_name) in + mercusys,mr90x-v1) + mount_ubi_part "tp_data" + ;; + *) + ;; + esac +} + +boot_hook_add preinit_main preinit_mount_cfg_part diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh index ec078741c98..cfddd9cedcc 100644 --- a/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/10_fix_eth_mac.sh @@ -8,6 +8,12 @@ preinit_set_mac_address() { ip link set dev eth0 address "$addr" ip link set dev eth1 address "$addr" ;; + mercusys,mr90x-v1) + addr=$(get_mac_binary "/tmp/tp_data/default-mac" 0) + ip link set dev eth1 address "$(macaddr_add $addr 1)" + ;; + *) + ;; esac } diff --git a/target/linux/mediatek/filogic/base-files/lib/preinit/81_fix_eeprom b/target/linux/mediatek/filogic/base-files/lib/preinit/81_fix_eeprom new file mode 100644 index 00000000000..0a842facca8 --- /dev/null +++ b/target/linux/mediatek/filogic/base-files/lib/preinit/81_fix_eeprom @@ -0,0 +1,16 @@ +. /lib/functions/system.sh + +preinit_fix_eeprom() { + case $(board_name) in + mercusys,mr90x-v1) + eeprom="/lib/firmware/mediatek/mt7986_eeprom_mt7975_dual.bin" + oem="/tmp/tp_data/MT7986_EEPROM.bin" + [ ! -L $eeprom -a -e $oem ] && \ + mv -f $eeprom $eeprom.bak && ln -s $oem $eeprom + ;; + *) + ;; + esac +} + +boot_hook_add preinit_main preinit_fix_eeprom diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index 5b624bc5517..11c2c5c6643 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -70,6 +70,10 @@ platform_do_upgrade() { cudy,wr3000-v1) default_do_upgrade "$1" ;; + mercusys,mr90x-v1) + CI_UBIPART="ubi0" + nand_do_upgrade "$1" + ;; qihoo,360t7|\ tplink,tl-xdr4288|\ tplink,tl-xdr6086|\ diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index ae25aee2ed8..fd83b9d4416 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -250,6 +250,20 @@ define Device/mediatek_mt7988a-rfb-nand endef TARGET_DEVICES += mediatek_mt7988a-rfb-nand +define Device/mercusys_mr90x-v1 + DEVICE_VENDOR := Mercusys + DEVICE_MODEL := MR90X v1 + DEVICE_DTS := mt7986b-mercusys-mr90x-v1 + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7986-firmware mt7986-wo-firmware + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 51200k + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += mercusys_mr90x-v1 + define Device/qihoo_360t7 DEVICE_VENDOR := Qihoo DEVICE_MODEL := 360T7