From: Daniel Golle Date: Wed, 14 Aug 2024 18:21:06 +0000 (+0100) Subject: ramips: mt76x8: add support for Yuncore M300 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e497c975d3719e1d09f169cad33f95cea0b396b6;p=openwrt%2Fstaging%2Fansuel.git ramips: mt76x8: add support for Yuncore M300 Hardware: - SoC: MediaTek MT7628DAN (MIPS 580MHz) - Flash: 8 MiB Spansion S25FL064K - RAM: 64 MiB (built-into SoC) - WLAN: 2.4 GHz (MT7628) - Ethernet: 1x 10/100 Mbps WAN, 1x 10/100 LAN (MT7628) - Buttons: 1 Reset button - LEDs: 1x Red, 1x Green - Serial console: unpopulated header, 57600 8n1 (RX only) - Power: 12 VDC, 1 A There are unpopulated areas on the board for 5 GHz WiFi via PCIe as well as (most likely) Quectel EG25-G 4G module. As both are not populated on my board support for both is missing for now. Installation: The installation can be done via the recovery HTTP server which is built into the bootloader. Hold down the reset button while connecting the device to power and keep holding a bit more than 3 seconds. Connect to http://192.168.188.253/ and upload sysupgrade.bin file. Signed-off-by: Daniel Golle --- diff --git a/target/linux/ramips/dts/mt7628an_yuncore_m300.dts b/target/linux/ramips/dts/mt7628an_yuncore_m300.dts new file mode 100644 index 0000000000..7a28c66996 --- /dev/null +++ b/target/linux/ramips/dts/mt7628an_yuncore_m300.dts @@ -0,0 +1,147 @@ +#include "mt7628an.dtsi" + +#include +#include +#include + +/ { + compatible = "yuncore,m300", "mediatek,mt7628an-soc"; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 38 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + aliases { + label-mac = ðernet; + led-boot = &led_indicator; + led-failsafe = &led_indicator; + led-running = &led_indicator; + led-upgrade = &led_indicator; + }; + + leds { + compatible = "gpio-leds"; + + led_indicator: indicator { + function = LED_FUNCTION_INDICATOR; + color = ; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + lan { + function = LED_FUNCTION_LAN; + color = ; + gpios = <&gpio 40 GPIO_ACTIVE_LOW>; + }; + + wan { + function = LED_FUNCTION_WAN; + color = ; + gpios = <&gpio 39 GPIO_ACTIVE_LOW>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 37 GPIO_ACTIVE_HIGH>; + hw_algo = "toggle"; + hw_margin_ms = <20000>; + always-running; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x400>; + }; + + macaddr_factory_4: macaddr@4 { + reg = <0x4 0x6>; + }; + }; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0x7b0000>; + }; + }; + }; +}; + +ðernet { + nvmem-cells = <&macaddr_factory_4>; + nvmem-cell-names = "mac-address"; +}; + +&esw { + mediatek,portmap = <0x3e>; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; +}; + +&state_default { + gpio { + groups = "pwm1", "pwm0", "uart2", "uart1", "i2c", "refclk", + "perst", "wdt", "sdmode", "i2s", "spi cs1", "spis", + "gpio", "p0led_an", "p1led_an", "p2led_an", "p3led_an", + "p4led_an", "wled_kn", "p0led_kn", "p1led_kn", + "p2led_kn", "p3led_kn", "p4led_kn"; + function = "gpio"; + }; + + wlan { + groups = "wled_an"; + function = "wled_an"; + }; +}; diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index 867c0e377b..71f09f816f 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -1136,6 +1136,13 @@ define Device/xiaomi_mi-ra75 endef TARGET_DEVICES += xiaomi_mi-ra75 +define Device/yuncore_m300 + IMAGE_SIZE := 7872k + DEVICE_VENDOR := Yuncore + DEVICE_MODEL := M300 +endef +TARGET_DEVICES += yuncore_m300 + define Device/zbtlink_zbt-we1226 IMAGE_SIZE := 7872k DEVICE_VENDOR := Zbtlink diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds index a42c9fe640..5a93761780 100644 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/01_leds @@ -18,7 +18,8 @@ asus,rt-n11p-b1|\ asus,rt-n12-vp-b1|\ netgear,r6020|\ netgear,r6080|\ -netgear,r6120) +netgear,r6120|\ +yuncore,m300) ucidef_set_led_switch "lan" "lan" "green:lan" "switch0" "0xf" ucidef_set_led_switch "wan" "wan" "green:wan" "switch0" "0x10" ;; diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network index e5326dfe79..2989d36e9b 100644 --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network @@ -81,7 +81,8 @@ ramips_setup_interfaces() buffalo,wcr-1166ds|\ elecom,wrc-1167fs|\ wavlink,wl-wn577a2|\ - wavlink,wl-wn578a2) + wavlink,wl-wn578a2|\ + yuncore,m300) ucidef_add_switch "switch0" \ "3:lan" "4:wan" "6@eth0" ;; diff --git a/target/linux/ramips/mt76x8/config-6.6 b/target/linux/ramips/mt76x8/config-6.6 index a2d7bc9866..b9dc8525df 100644 --- a/target/linux/ramips/mt76x8/config-6.6 +++ b/target/linux/ramips/mt76x8/config-6.6 @@ -84,6 +84,8 @@ CONFIG_GPIO_CDEV=y CONFIG_GPIO_GENERIC=y CONFIG_GPIO_MT7621=y # CONFIG_GPIO_RALINK is not set +CONFIG_GPIO_WATCHDOG=y +# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set CONFIG_HARDWARE_WATCHPOINTS=y CONFIG_HAS_DMA=y CONFIG_HAS_IOMEM=y