From: Hang Zhou <929513338qq@gmail.com> Date: Sun, 26 Feb 2023 09:13:33 +0000 (+1100) Subject: ramips: add support for D-Link Dir-853 A1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e45195716612edfbf359c107521ebcdd1e409ca9;p=openwrt%2Fstaging%2Fsvanheule.git ramips: add support for D-Link Dir-853 A1 Specifications: * SoC: MT7621AT * RAM: 256MB (NT5CC64M16GP-DI) * Flash: 16MB NOR SPI flash (GD25Q127CSIG, using GD25Q128C driver) * WiFi: MT7615DN (2.4GHz+5Ghz) with DBDC * Ethernet: 4x1000M LAN, 1x 1000M WAN * LEDs: Power Blue+Orange,Wan Blue+Orange,WPS Blue,"2.4G"Blue, "5G" Blue, USB Blue * Buttons: Reset,WPS, Wifi * Serial interface: on board but not populated, pinout (from the DC jack side to the WAN port side) is "3.3V Input Output Gnd". Baud rate is 57600, settings are 8 data bits, no parity bit, one stop bit, and no flow control. Stock flash layout: ``` GD25Q128C(c8 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (16M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 7 MTD partitions on "raspi": 0x000000000000-0x000001000000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000060000 : "Config2" 0x000000060000-0x000000fb0000 : "Kernel" 0x000000fb0000-0x000001000000 : "Private" ``` The kernel partition will be replaced with the OpenWrt image, the other partitions are left untouched. "Config2" seems to be the config storage used by the stock firmware. "Private" is a 320kB empty JFFS2 partition that comes with the stock firmware. One can get a larger space for OpenWrt by merging it with "Kernel". OpenWrt flash layout: ``` 0x000000000000-0x000000030000 : "u-boot" 0x000000030000-0x000000040000 : "u-boot-env" 0x000000040000-0x000000050000 : "factory" 0x000000050000-0x000000060000 : "config2_stock" 0x000000060000-0x000000fb0000 : "firmware" 0x000000fb0000-0x000001000000 : "private_stock" ``` The OpenWrt image must have 96 bytes of padding in the header. MAC addresses on OEM firmware: | | location on the flash | notes | |------ |----------------------- |---------- | | lan (eth2) | factory + 0xe000 | on label | | wan (eth3) | factory + 0xe006 | | | 2.4g (rax0) | not on flash | lan + 1 | | 5g (ra0) | not on flash | lan + 2 | Mac addresses of the 2.4g and 5g interface are stored as ASCII strings in the u-boot-env partition, but they are not used. OpenWrt calculates Wifi Mac addresses based on the LAN Mac. Flash and test instructions: Flash the encrypted image (available in the OpenWrt forum) through the stock D-Dink web interface. 1. Open the case, and solder the 4-pin header near the WAN port. 2. Connect it to a USB-UART TTL (3.3V) adapter, no need to connect VCC. 3. Open a terminal emulator (e.g. `screen /dev/ttyUSB0` on linux) with the settings mentioned above. 4. Setup a TFTP server on your PC that can serve `xxx-ramips-mt7621-dlink_dir-853-a1-initramfs-kernel.bin`. 5. Connect any LAN port to your PC and set a static IPv4 address to 192.168.0.101 (netmask 255.255.255.0). 6. Power on the device and keeps pressing 1 until you see the prompt. 7. Use default IP addresses and enter the file name accordingly, then hit enter. 8. Wait until it boots to OpenWrt, the default IP address is 192.168.1.1, you need to change your PC network adapter to use DHCP in order to access LUCI. 9. So far, the OpenWrt runs in RAM and the flash contents are not touched. You can try OpenWrt without having to overwrite the stock firmware, a reboot clears all changes. 10. Optionally, backup the stock firmware (the "firmware" partition) in Luci. 11. To permantly install OpenWrt to the device , click on "System -> Backup/Flash Firmware" in Luci and flash `xxx-ramips-mt7621-dlink_dir-853-a1-squashfs-sysupgrade.bin` Known problems: * WLAN0 defaults to 5G after a fresh installation, to enable 2.4G network, you need to config it manually in LUCI. * If you see jffs2 related warnings/errors after updating from the stock web interface, you need to do a reset in LUCI. The error will be gone after a cold reboot. Signed-off-by: Hang Zhou <929513338qq@gmail.com> --- diff --git a/target/linux/ramips/dts/mt7621_dlink_dir-853-a1.dts b/target/linux/ramips/dts/mt7621_dlink_dir-853-a1.dts new file mode 100644 index 0000000000..2b6b811abe --- /dev/null +++ b/target/linux/ramips/dts/mt7621_dlink_dir-853-a1.dts @@ -0,0 +1,216 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "dlink,dir-853-a1", "mediatek,mt7621-soc"; + model = "D-Link DIR-853 A1"; + + aliases { + led-boot = &led_power_orange; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_net_orange; + }; + + keys { + compatible = "gpio-keys"; + + wifi { + label = "wifi"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + wlan5g { + label = "blue:wlan5g"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1radio"; + }; + + wlan2g { + label = "blue:wlan2g"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0radio"; + }; + + usb_blue { + label = "blue:usb"; + gpios = <&gpio 10 GPIO_ACTIVE_LOW>; + trigger-sources = <&xhci_ehci_port1>; + linux,default-trigger = "usbport"; + }; + + led_power_orange: power_orange { + label = "orange:power"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + led_power_blue: power_blue { + label = "blue:power"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led_net_orange: net_orange { + label = "orange:net"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + net_blue { + label = "blue:net"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <50000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "config2_stock"; + reg = <0x50000 0x10000>; + read-only; + }; + + partition@60000 { + compatible = "openwrt,uimage", "denx,uimage"; + openwrt,padding = <96>; + label = "firmware"; + reg = <0x60000 0xf50000>; + }; + + partition@fb0000 { + label = "private_stock"; + reg = <0xfb0000 0x50000>; + read-only; + }; + }; + }; +}; + + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0>; + + /* The correct Mac addresses are set in 10_fix_wifi_mac. */ + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr_factory_e000>; + nvmem-cell-names = "mac-address"; +}; + +&gmac1 { + status = "okay"; + label = "wan"; + phy-handle = <ðphy4>; + + nvmem-cells = <&macaddr_factory_e006>; + nvmem-cell-names = "mac-address"; +}; + +&mdio { + ethphy4: ethernet-phy@4 { + reg = <4>; + }; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan4"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + }; +}; + +&state_default { + gpio { + groups = "i2c", "uart2", "uart3", "jtag", "wdt"; + function = "gpio"; + }; +}; + +&factory { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_e000: macaddr@e000 { + reg = <0xe000 0x6>; + }; + + macaddr_factory_e006: macaddr@e006 { + reg = <0xe006 0x6>; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 822e62a69c..78ad0e5c09 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -624,6 +624,14 @@ define Device/dlink_dir-3060-a1 endef TARGET_DEVICES += dlink_dir-3060-a1 +define Device/dlink_dir-853-a1 + $(Device/dlink_dir-8xx-a1) + DEVICE_MODEL := DIR-853 + DEVICE_VARIANT := A1 + DEVICE_PACKAGES += kmod-usb3 kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += dlink_dir-853-a1 + define Device/dlink_dir-853-a3 $(Device/dlink_dir-xx60-a1) DEVICE_MODEL := DIR-853 diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index f54905cf5c..039417dbbb 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -76,6 +76,7 @@ dlink,dir-3060-a1) ucidef_set_led_netdev "net_white" "WAN Link" "white:net" "wan" "link" ucidef_set_led_netdev "net_orange" "WAN Activity" "orange:net" "wan" "tx rx" ;; +dlink,dir-853-a1|\ dlink,dir-853-a3) ucidef_set_led_netdev "wan" "wan" "blue:net" "wan" ;; diff --git a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 45bee29d24..b8d8befeef 100644 --- a/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ramips/mt7621/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -38,6 +38,13 @@ case "$board" in [ "$PHYNBR" = "1" ] && \ macaddr_add $hw_mac_addr 4 > /sys${DEVPATH}/macaddress ;; + dlink,dir-853-a1) + lan_mac_addr="$(mtd_get_mac_binary factory 0xe000)" + [ "$PHYNBR" = "0" ] && \ + macaddr_add $lan_mac_addr 1 > /sys${DEVPATH}/macaddress + [ "$PHYNBR" = "1" ] && \ + macaddr_add $lan_mac_addr 2 > /sys${DEVPATH}/macaddress + ;; dlink,dir-853-a3) [ "$PHYNBR" = "0" ] && \ macaddr_setbit_la "$(mtd_get_mac_binary factory 0xe000)" \