From: Russell Senior Date: Sun, 25 Nov 2018 11:39:19 +0000 (-0800) Subject: ramips: add support for Skylab SKW92A in EVB X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e42327aa890e64f8bf5e620c2b2a1fd609ce20fb;p=openwrt%2Fstaging%2Fdedeckeh.git ramips: add support for Skylab SKW92A in EVB Specifically, SKW92A_E16, described here: http://www.skylabmodule.com/wp-content/uploads/SkyLab_SKW92A_V1.04_datasheet.pdf Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 16 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x u.FL - Power by micro-USB connector at USB1 on EVB - UART via micro-USB connector at USB3 on EVB (57600 8n1) - 5x Ethernet LEDs - 1x WLAN LEDs - 1x WPS LED connected by jumper wire from I2S_CK on J20 to WPS_LED pin hole next to daughter board on EVB - WPS/Reset button (S2 on EVB) - RESET button (S1 on EVB) is *not* connected to RST hole next to daughter board Flash instruction: >From Skylab firmware: 1. Associate with SKYLAP_AP 2. In a browser, load: http://10.10.10.254/ 3. Username/password: admin/admin 4. In web admin interface: Administration / Upload Firmware, browse to sysupgrade image, apply, flash will fail with a message: Not a valid firmware. *** Warning: "/var/tmpFW" has corrupted data! 5. Telnet to 10.10.10.254, drops you into a root shell with no credentials 6. # cd /var 7. # mtd_write -r write tmpFW mtd4 Unlocking mtd4 ... Writing from tmpFW to mtd4 ... [e] 8. When flash has completed, you will have booted into your firmware. >From U-boot via TFTP and initramfs: 1. Place openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin on a TFTP server 2. Connect to serial console at USB3 on EVB 3. Connect ethernet between port 1 (not WAN) and your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "1" 7. At u-boot prompts: Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-initramfs-kernel.bin 8. Move ethernet to port 0 (WAN) on EVB 9. At new OpenWrt console shell, fetch squashfs-sysupgrade image and flash with sysupgrade. >From U-boot via TFTP direct flash: 1. Place openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin on a TFTP server 2. Connect to serial console at USB3 on EVB (57600 8N1) 3. Connect ethernet between port 1 (not WAN) an your TFTP server (e.g. 192.168.11.20) 4. Start terminal software (e.g. screen /dev/ttyUSB0 57600) on PC 5. Apply power to EVB 6. Interrupt u-boot with keypress of "2" 7. At u-boot prompts: Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N) Y Input device IP (10.10.10.123) ==:192.168.11.21 Input server IP (10.10.10.3) ==:192.168.11.20 Input Linux Kernel filename (root_uImage) ==:openwrt-ramips-mt76x8-skw92a-squashfs-sysupgrade.bin 8. When transfer is complete or as OpenWrt begins booting, move ethernet to port 0 (WAN). Signed-off-by: Russell Senior --- diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 2644bc0159..825a65b1d1 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -283,6 +283,9 @@ rt-n14u) ucidef_set_led_netdev "wan" "wan" "$boardname:blue:wan" eth0.2 set_wifi_led "$boardname:blue:air" ;; +skw92a) + set_wifi_led "$boardname:green:wlan" + ;; tama,w06) ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth0" ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" "phy0tpt" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 9e9ecbcb51..ac9f368419 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -345,6 +345,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "0:lan" "1:lan" "2:lan" "3:lan" "4:wan" "8@eth0" ;; + skw92a) + ucidef_add_switch "switch0" \ + "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0" + ;; tew-638apb-v2) ucidef_add_switch "switch0" \ "4:lan" "6@eth0" @@ -554,6 +558,10 @@ ramips_setup_macs() lan_mac=$(macaddr_setbit_la "$lan_mac") wan_mac=$(mtd_get_mac_binary factory 32772) ;; + skw92a) + lan_mac=$(mtd_get_mac_binary factory 40) + wan_mac=$(mtd_get_mac_binary factory 46) + ;; tew-691gr) wan_mac=$(macaddr_add "$(mtd_get_mac_binary factory 4)" 3) ;; diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index 5741cbd2ee..249533f06e 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -472,6 +472,9 @@ ramips_board_detect() { *"SAP-G3200U3") name="sap-g3200u3" ;; + *"SKW92A") + name="skw92a" + ;; *"SL-R7205"*) name="sl-r7205" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 7558b4e316..7fb17743cd 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -151,6 +151,7 @@ platform_check_image() { rut5xx|\ sap-g3200u3|\ sk-wb8|\ + skw92a|\ sl-r7205|\ tama,w06|\ tew-638apb-v2|\ diff --git a/target/linux/ramips/dts/SKW92A.dts b/target/linux/ramips/dts/SKW92A.dts new file mode 100644 index 0000000000..c43f9e53ea --- /dev/null +++ b/target/linux/ramips/dts/SKW92A.dts @@ -0,0 +1,120 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7628an.dtsi" + +#include +#include + +/{ + compatible = "skylab,skw92a", "mediatek,mt7628an-soc"; + model = "SKW92A"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x4000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_power: wps { + label = "skw92:green:wps"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys-polled"; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + }; +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "wdt", "refclk", "gpio"; + ralink,function = "gpio"; + }; + }; +}; + +ðernet { + mtd-mac-address = <&factory 0x28>; +}; + +&wmac { + status = "okay"; + ralink,mtd-eeprom = <&factory 0x0>; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + m25p,chunked-io = <32>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0xfb0000>; + compatible = "denx,uimage"; + }; + }; + }; +}; + +&uart1 { + status = "okay"; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; diff --git a/target/linux/ramips/image/mt76x8.mk b/target/linux/ramips/image/mt76x8.mk index 6bedb4f7d4..5f40262e84 100644 --- a/target/linux/ramips/image/mt76x8.mk +++ b/target/linux/ramips/image/mt76x8.mk @@ -150,6 +150,14 @@ define Device/pbr-d1 endef TARGET_DEVICES += pbr-d1 +define Device/skw92a + DTS := SKW92A + IMAGE_SIZE := 16064k + DEVICE_TITLE := Skylab SKW92A + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci +endef +TARGET_DEVICES += skw92a + define Device/tplink_tl-wa801nd-v5 $(Device/tplink) DTS := TL-WA801NDV5