From: Rani Hod Date: Sun, 12 Nov 2023 23:15:31 +0000 (+0200) Subject: ath79: add support for D-link DAP-1720 A1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=e29f4a3f70d278cf7e360519d97d94f54baae278;p=openwrt%2Fstaging%2Fnbd.git ath79: add support for D-link DAP-1720 A1 D-Link DAP-1720 rev A1 is a mains-powered AC1750 Wi-Fi range extender, manufactured by Alpha Networks [8WAPAC28.1A1G]. (in square brackets: PCB silkscreen markings) Specifications: * CPU (Qualcomm Atheros QCA9563-AL3A [U5]): 775 MHz single core MIPS 74Kc; * RAM (Winbond W9751G6KB-25J [U3]): 64 MiB DDR2; * ROM (Winbond W25Q128FV [U16]): 16 MiB SPI NOR flash; * Ethernet (AR8033-AL1A PHY [U1], no switch): 1 GbE RJ45 port (no PHY LEDs); * Wi-Fi * 2.4 GHz (Qualcomm Atheros QCA9563-AL3A [U5]): 3x3 802.11n; * 5 GHz (Qualcomm Atheros QCA9880-BR4A [U9]): 3x3 802.11ac Wave 1; * 3 foldable dual-band antennas (U.fl) [P1],[P2],[P3]; * GPIO LEDs: * RSSI low (red/green) [D2]; * RSSI medium (green) [D3]; * RSSI high (green) [D4]; * status (red/green) [D5]; * GPIO buttons: * WPS [SW1], co-located with status LED; * reset [SW4], accessible via hole in the side; * Serial/UART: Tx-Gnd-3v3-Rx [JP1], Tx is the square pin, 1.25mm pitch; 125000-8-n-1 in U-boot, 115200-8-n-1 in kernel; * Misc: * 12V VCC [JP2], fed from internal 12V/1A AC to DC converter; * on/off slide switch [SW2] (disconnects VCC mechanically); * unpopulated footprints for a Wi-Fi LED [D1]; * unpopulated footprints for a 4-pin 3-position slide switch (SW3); MAC addresses: * Label = LAN; * 2.4 GHz WiFi = LAN; * 5 GHz WiFi = LAN+2; Installation: * `factory.bin` can be used to install OpenWrt from OEM firmware via the standard upgrade webpage at http://192.168.0.50/UpdateFirmware.html * `recovery.bin` can be used to install OpenWrt (or revert to OEM firmware) from D-Link Web Recovery. To enter web recovery, keep reset button pressed and then power on the device. Reset button can be released when the red status LED is bright; it will then blink slowly. Set static IP to 192.168.0.10, navigate to http://192.168.0.50 and upload 'recovery.bin'. Note that in web recovery mode the device ignores ping and DHCP requests. Note: 802.11s is not supported by the default `ath10k` driver and firmware, but is supported by the non-CT driver and firmware variants. The `-smallbuffers` driver variant is recommended due to RAM size. Co-developed-by: Anthony Sepa Signed-off-by: Rani Hod --- diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 2ad79700d7..7c0cdf9013 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -31,6 +31,7 @@ asus,zenwifi-cd6n|\ asus,zenwifi-cd6r|\ buffalo,bhr-4grv2|\ devolo,magic-2-wifi|\ +dlink,dap-1720-a1|\ dlink,dir-859-a1|\ dlink,dir-859-a3|\ dlink,dir-869-a1|\ diff --git a/target/linux/ath79/dts/qca9563_dlink_dap-1720-a1.dts b/target/linux/ath79/dts/qca9563_dlink_dap-1720-a1.dts new file mode 100644 index 0000000000..35f3913d9b --- /dev/null +++ b/target/linux/ath79/dts/qca9563_dlink_dap-1720-a1.dts @@ -0,0 +1,214 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca956x.dtsi" + +#include +#include +#include + +/ { + model = "D-Link DAP-1720 A1"; + compatible = "dlink,dap-1720-a1", "qca,qca9563"; + + aliases { + led-boot = &led_status_green; + led-failsafe = &led_status_red; + led-running = &led_status_green; + led-upgrade = &led_status_red; + + label-mac-device = ð0; + }; + + keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + button-wps { + label = "wps"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_status_red: led-status-red { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + panic-indicator; + }; + + led_status_green: led-status-green { + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + led-rssi-middle { + color = ; + function = "signal"; //LED_FUNCTION_SIGNAL; + function-enumerator = <2>; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + + led-rssi-top { + color = ; + function = "signal"; //LED_FUNCTION_SIGNAL; + function-enumerator = <3>; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + led-rssi-bottom-green { + color = ; + function = "signal"; //LED_FUNCTION_SIGNAL; + function-enumerator = <1>; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + }; + + led-rssi-bottom-red { + color = ; + function = "signal"; //LED_FUNCTION_SIGNAL; + function-enumerator = <1>; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; // vendor calls it `bootloader` + reg = <0x000000 0x40000>; + read-only; + }; + + partition@40000 { + compatible = "u-boot,env"; + label = "u-boot-env"; // vendor calls it `bdcfg` + reg = <0x040000 0x10000>; + read-only; + }; + + partition@50000 { + label = "devdata"; + reg = <0x050000 0x10000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_ath10k: macaddr@94 { + compatible = "mac-base"; + reg = <0x94 0x11>; + #nvmem-cell-cells = <1>; + }; + + macaddr_ath9k: macaddr@b0 { + compatible = "mac-base"; + reg = <0xb0 0x11>; + #nvmem-cell-cells = <1>; + }; + + macaddr_lan: macaddr@c9 { + compatible = "mac-base"; + reg = <0xc9 0x11>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@60000 { + label = "devconf"; + reg = <0x060000 0x10000>; + read-only; + }; + + partition@70000 { + compatible = "seama"; + label = "firmware"; + reg = <0x070000 0xf80000>; + }; + + partition@ff0000 { + label = "art"; // vendor calls it `radiocfg` + reg = <0xff0000 0x010000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + cal_ath9k: cal@1000 { + reg = <0x1000 0x440>; + }; + + cal_ath10k: cal@5000 { + reg = <0x5000 0x844>; + }; + }; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&phy0>; + phy-mode = "sgmii"; + + nvmem-cells = <&macaddr_lan 0>; + nvmem-cell-names = "mac-address"; +}; + +&pcie { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0x0000 0 0 0 0>; + + nvmem-cells = <&cal_ath10k>, <&macaddr_ath10k 0>; + nvmem-cell-names = "calibration", "mac-address"; + }; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&cal_ath9k>, <&macaddr_ath9k 0>; + nvmem-cell-names = "calibration", "mac-address"; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index c1d411b9a9..615abe4b3b 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -241,6 +241,13 @@ dlink,dap-1365-a1) ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "green:rssimediumhigh" "wlan0" "51" "100" ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:rssihigh" "wlan0" "76" "100" ;; +dlink,dap-1720-a1) + ucidef_set_rssimon "wlan0" "200000" "1" + ucidef_set_led_rssi "rssilow" "RSSI LOW" "red:signal-1" "wlan0" "1" "40" + ucidef_set_led_rssi "rssimediumlow" "RSSI MEDIUM-LOW" "green:signal-1" "wlan0" "21" "100" + ucidef_set_led_rssi "rssimediumhigh" "RSSI MEDIUM-HIGH" "green:signal-2" "wlan0" "61" "100" + ucidef_set_led_rssi "rssihigh" "RSSI HIGH" "green:signal-3" "wlan0" "81" "100" + ;; dlink,dir-859-a1) ucidef_set_led_switch "internet" "WAN" "green:internet" "switch0" "0x20" ;; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index a9b78e4350..cdea3b5f67 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -34,6 +34,7 @@ ath79_setup_interfaces() devolo,dvl1750x|\ dlink,dap-1330-a1|\ dlink,dap-1365-a1|\ + dlink,dap-1720-a1|\ dlink,dap-2230-a1|\ dlink,dap-2660-a1|\ dlink,dap-2680-a1|\ diff --git a/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum b/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum index 0ea81a8dc3..4ec8c13eb7 100644 --- a/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum +++ b/target/linux/ath79/generic/base-files/etc/uci-defaults/09_fix-checksum @@ -21,6 +21,7 @@ dlink,dap-3320-a1|\ dlink,dap-3662-a1) fixwrgg ;; +dlink,dap-1720-a1|\ dlink,dir-629-a1|\ dlink,dir-859-a1|\ dlink,dir-859-a3|\ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index e6e78b9287..e435806c7b 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1053,6 +1053,22 @@ define Device/dlink_dap-1365-a1 endef TARGET_DEVICES += dlink_dap-1365-a1 +define Device/dlink_dap-1720-a1 + $(Device/seama) + SOC := qca9563 + DEVICE_VENDOR := D-Link + DEVICE_MODEL := DAP-1720 + DEVICE_VARIANT := A1 + DEVICE_PACKAGES := rssileds -swconfig \ + kmod-ath10k-ct-smallbuffers ath10k-firmware-qca988x-ct + SEAMA_SIGNATURE := wapac28_dlink.2015_dap1720 + IMAGE_SIZE := 15872k + IMAGES += recovery.bin + IMAGE/recovery.bin := $$(IMAGE/default) | pad-rootfs -x 64 | seama | \ + seama-seal | check-size +endef +TARGET_DEVICES += dlink_dap-1720-a1 + define Device/dlink_dap-2xxx IMAGES += factory.img IMAGE/factory.img := append-kernel | pad-offset 6144k 160 | \