From: Xinfa Deng Date: Thu, 9 Feb 2023 07:37:30 +0000 (+0800) Subject: ath79: add support for GL.iNet GL-X1200 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=dd8a4a8c34c0b721000198ff01f2ff5158f32414;p=openwrt%2Fstaging%2Fneocturne.git ath79: add support for GL.iNet GL-X1200 This patch adds supports for GL-X1200. Specification: - SOC: QCA9563 (775MHz) - Flash: 16 MiB - RAM: 128 MiB DDR2 - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN - Wireless: QCA9563(2.4GHz) and QCA9886(5GHz) - SIM: 2x SIM card slots - MicroSD: 1x microSD slot - Antenna: 2x external 5dBi antennas - USB: 1x USB 2.0 port - Button: 1x reset button - LED: 16x LEDs (3x GPIO controllable) - UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND) - OEM U-Boot supplies HTTP/GUI access Implementation Notes ==================== Both the NOR and NAND variants boot off a NOR-based kernel, consistent with the OEM's firmware. The mode LEDs are * Boot, Running system * Failsafe 2G * Upgrade 5G Installation ============ Using sysupgrade ---------------- sysupgrade may be used to install a NAND image on a device running a NAND image or a NOR image on a device running a NOR image. It is recommended to *not* preserve config when upgrading from OEM firmware or previous versions of OpenWrt. No supported sysupgrade path should require "force". Transitioning from NOR to NAND can be accomplished Using U-Boot ------------ The OEM U-Boot can be put into a graphical, firmware-upload mode by holding down the button on the side of the router while applying power and for a bit more than five seconds following with the current OEM U-Boot. The power LED will come on, then the 5G LED will flash five times, about once a second. When the 5G LED stops flashing and the 2G LED lights solid, the router's U-Boot will provide an upload page at http://192.168.1.1/ Either a browser may be used to upload an image, or a utility such as curl may be used: curl -X POST -F gl_firmware=\@*-nand-squashfs-factory.img \ http://192.168.1.1/index.html or curl -X POST -F gl_firmware=\@*-nor-squashfs-sysupgrade.bin \ http://192.168.1.1/index.html Note that NOR vs. NAND is based on the file name extension. Signed-off-by: Xinfa Deng --- diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts new file mode 100644 index 0000000000..2a26d959c9 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor-nand.dts @@ -0,0 +1,29 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_glinet_gl-x1200.dtsi" + +/ { + compatible = "glinet,gl-x1200-nor-nand", "qca,qca9563"; + model = "GL.iNet GL-X1200 (NOR/NAND)"; +}; + +&nor_partitions { + partition@60000 { + label = "kernel"; + reg = <0x060000 0x400000>; + + /* + * U-Boot bootcmd is "bootm 0x9f060000". + * So this might be possible to resize in the future. + */ + }; + + partition@460000 { + label = "nor_reserved"; + reg = <0x460000 0xba0000>; + }; +}; + +&nand_ubi { + label = "ubi"; +}; diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts new file mode 100644 index 0000000000..dfce3818b0 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200-nor.dts @@ -0,0 +1,16 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_glinet_gl-x1200.dtsi" + +/ { + compatible = "glinet,gl-x1200-nor", "qca,qca9563"; + model = "GL.iNet GL-X1200 (NOR)"; +}; + +&nor_partitions { + partition@60000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x060000 0xfa0000>; + }; +}; diff --git a/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi new file mode 100644 index 0000000000..8980f772e7 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_glinet_gl-x1200.dtsi @@ -0,0 +1,209 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca956x.dtsi" + +#include +#include + +/ { + aliases { + led-boot = &led_system; + led-failsafe = &led_system; + led-running = &led_system; + led-upgrade = &led_system; + label-mac-device = ð0; + }; + + keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins>; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_system: system { + label = "red:system"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wlan2g { + label = "green:wlan2g"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + label = "green:wlan5g"; + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + }; + + gpio-export { + compatible = "gpio-export"; + + gpio_modem1_power { + gpio-export,name = "gl-x1200:4g1:power"; + gpio-export,output = <0>; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + gpio_modem2_power { + gpio-export,name = "gl-x1200:4g2:power"; + gpio-export,output = <0>; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + nor_partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + label = "art"; + reg = <0x050000 0x010000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + calibration_ath9k: calibration@1000 { + reg = <0x1000 0x440>; + }; + + calibration_ath10k: calibration@5000 { + reg = <0x5000 0x2f20>; + }; + + macaddr_art_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_1002: macaddr@1002 { + reg = <0x1002 0x6>; + }; + + macaddr_art_5006: macaddr@5006 { + reg = <0x5006 0x6>; + }; + }; + + /* Firmware / Kernel flash type specific */ + }; + }; + + flash@1 { + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + nand_ubi: partition@0 { + label = "nand_ubi"; + reg = <0x000000 0x8000000>; + }; + }; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&phy0>; + + nvmem-cells = <&macaddr_art_0>; + nvmem-cell-names = "mac-address"; +}; + +&gpio { + usb_vbus { + gpio-hog; + gpios = <7 GPIO_ACTIVE_HIGH>; + output-high; + line-name = "usb-vbus"; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + qca,ar8327-initvals = < + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +&pcie { + status = "okay"; + + wifi@0,0 { + compatible = "qcom,ath10k"; + reg = <0 0 0 0 0>; + + nvmem-cells = <&macaddr_art_5006>, <&calibration_ath10k>; + nvmem-cell-names = "mac-address", "pre-calibration"; + }; +}; + +&usb0 { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; + +&usb_phy0 { + status = "okay"; +}; + +&usb_phy1 { + status = "okay"; +}; + +&wmac { + status = "okay"; + + nvmem-cells = <&macaddr_art_1002>, <&calibration_ath9k>; + nvmem-cell-names = "mac-address", "calibration"; +}; diff --git a/target/linux/ath79/image/nand.mk b/target/linux/ath79/image/nand.mk index c83beef952..40c57d8b06 100644 --- a/target/linux/ath79/image/nand.mk +++ b/target/linux/ath79/image/nand.mk @@ -212,6 +212,35 @@ define Device/glinet_gl-xe300 endef TARGET_DEVICES += glinet_gl-xe300 +define Device/glinet_gl-x1200-common + SOC := qca9563 + DEVICE_VENDOR := GL.iNet + DEVICE_MODEL := GL-X1200 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct-htt kmod-usb2 \ + kmod-usb-storage block-mount kmod-usb-net-qmi-wwan uqmi + IMAGE_SIZE := 16000k +endef + +define Device/glinet_gl-x1200-nor-nand + $(Device/glinet_gl-x1200-common) + DEVICE_VARIANT := NOR/NAND + KERNEL_SIZE := 4096k + IMAGE_SIZE := 131072k + PAGESIZE := 2048 + VID_HDR_OFFSET := 2048 + BLOCKSIZE := 128k + IMAGES += factory.img + IMAGE/factory.img := append-kernel | pad-to $$$$(KERNEL_SIZE) | append-ubi + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += glinet_gl-x1200-nor-nand + +define Device/glinet_gl-x1200-nor + $(Device/glinet_gl-x1200-common) + DEVICE_VARIANT := NOR +endef +TARGET_DEVICES += glinet_gl-x1200-nor + define Device/linksys_ea4500-v3 SOC := qca9558 DEVICE_VENDOR := Linksys diff --git a/target/linux/ath79/nand/base-files/etc/board.d/02_network b/target/linux/ath79/nand/base-files/etc/board.d/02_network index b163b29db1..137f3aa11b 100644 --- a/target/linux/ath79/nand/base-files/etc/board.d/02_network +++ b/target/linux/ath79/nand/base-files/etc/board.d/02_network @@ -30,6 +30,11 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "4:lan" ;; + glinet,gl-x1200-nor|\ + glinet,gl-x1200-nor-nand) + ucidef_add_switch "switch0" \ + "0@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" "5:wan" + ;; linksys,ea4500-v3) ucidef_add_switch "switch0" \ "6@eth1" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" "0@eth0" @@ -88,6 +93,11 @@ ath79_setup_macs() wan_mac=$(mtd_get_mac_binary art 0x0) label_mac=$wan_mac ;; + glinet,gl-x1200-nor|\ + glinet,gl-x1200-nor-nand) + wan_mac=$(mtd_get_mac_binary art 0x0) + lan_mac=$(macaddr_add "$wan_mac" 1) + ;; netgear,wndr3700-v4|\ netgear,wndr4300|\ netgear,wndr4300sw|\ diff --git a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh index ea77345b06..5a4f76ba51 100644 --- a/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/nand/base-files/lib/upgrade/platform.sh @@ -19,7 +19,9 @@ platform_do_upgrade() { glinet_nand_nor_do_upgrade "$1" ;; glinet,gl-ar750s-nor|\ - glinet,gl-ar750s-nor-nand) + glinet,gl-ar750s-nor-nand|\ + glinet,gl-x1200-nor|\ + glinet,gl-x1200-nor-nand) nand_nor_do_upgrade "$1" ;; *)