From: Sven Eckelmann Date: Mon, 23 Nov 2020 12:41:34 +0000 (+0100) Subject: ath79: Add support for OpenMesh OM2P v4 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=dd1d95cb0357278900d09fae3ad20e9e0b2d569a;p=openwrt%2Fstaging%2Fblocktrron.git ath79: Add support for OpenMesh OM2P v4 Device specifications: ====================== * Qualcomm/Atheros QCA9533 v2 * 650/600/217 MHz (CPU/DDR/AHB) * 64 MB of RAM * 16 MB of SPI NOR flash - 2x 7 MB available; but one of the 7 MB regions is the recovery image * 2x 10/100 Mbps Ethernet * 1T1R 2.4 GHz Wi-Fi * 6x GPIO-LEDs (3x wifi, 2x ethernet, 1x power) * 1x GPIO-button (reset) * external h/w watchdog (enabled by default) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x fast ethernet - eth0 + Label: Ethernet 1 + 24V passive POE (mode B) - eth1 + Label: Ethernet 2 + 802.3af POE + builtin switch port 1 * 12-24V 1A DC * external antenna Flashing instructions: ====================== Various methods can be used to install the actual image on the flash. Two easy ones are: ap51-flash ---------- The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the image to the u-boot when the device boots up. initramfs from TFTP ------------------- The serial console must be used to access the u-boot shell during bootup. It can then be used to first boot up the initramfs image from a TFTP server (here with the IP 192.168.1.21): setenv serverip 192.168.1.21 setenv ipaddr 192.168.1.1 tftpboot 0c00000 .bin && bootm $fileaddr The actual sysupgrade image can then be transferred (on the LAN port) to the device via scp .bin root@192.168.1.1:/tmp/ On the device, the sysupgrade must then be started using sysupgrade -n /tmp/.bin Signed-off-by: Sven Eckelmann [wrap two very long lines, fix typo in comment] Signed-off-by: Adrian Schmutzler --- diff --git a/package/boot/uboot-envtools/Makefile b/package/boot/uboot-envtools/Makefile index 590e38d883..4d2b03e33c 100644 --- a/package/boot/uboot-envtools/Makefile +++ b/package/boot/uboot-envtools/Makefile @@ -10,7 +10,7 @@ include $(TOPDIR)/rules.mk PKG_NAME:=uboot-envtools PKG_DISTNAME:=u-boot PKG_VERSION:=2020.04 -PKG_RELEASE:=9 +PKG_RELEASE:=10 PKG_SOURCE:=$(PKG_DISTNAME)-$(PKG_VERSION).tar.bz2 PKG_SOURCE_URL:= \ diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 1eaaa06f0e..ba857e54ed 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -85,6 +85,7 @@ netgear,wndr4300tn|\ netgear,wndr4300sw) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x20000" ;; +openmesh,om2p-v4|\ plasmacloud,pa300|\ plasmacloud,pa300e) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x40000" diff --git a/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts new file mode 100644 index 0000000000..b738afad33 --- /dev/null +++ b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9533_openmesh_om2p-v4.dtsi" + +/ { + compatible = "openmesh,om2p-v4", "qca,qca9533"; + model = "OpenMesh OM2P v4"; +}; diff --git a/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi new file mode 100644 index 0000000000..74daba3f93 --- /dev/null +++ b/target/linux/ath79/dts/qca9533_openmesh_om2p-v4.dtsi @@ -0,0 +1,157 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca953x.dtsi" + +#include +#include + +/ { + chosen { + /delete-property/ bootargs; + }; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_blue; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + label-mac-device = ð0; + }; + + keys { + compatible = "gpio-keys"; + + pinctrl-names = "default"; + pinctrl-0 = <&jtag_disable_pins>; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_blue: power_blue { + label = "blue:power"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wifi_green { + label = "green:wifi"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wifi_yellow { + label = "yellow:wifi"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + wifi_red { + label = "red:wifi"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + wan_blue { + label = "blue:wan"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + + lan_blue { + label = "blue:lan"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + /* hw_margin_ms is actually 300s but driver limits it to 60s */ + hw_margin_ms = <60000>; + always-running; + }; +}; + +&uart { + status = "okay"; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + /* partitions are passed via bootloader */ + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x040000>; + }; + + partition@80000 { + label = "custom"; + reg = <0x080000 0x140000>; + read-only; + }; + + partition@1c0000 { + label = "inactive"; + reg = <0x1c0000 0x700000>; + }; + + partition@8c0000 { + label = "inactive2"; + reg = <0x8c0000 0x700000>; + }; + + art: partition@fc0000 { + label = "ART"; + reg = <0xfc0000 0x040000>; + read-only; + }; + }; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&swphy4>; + + mtd-mac-address = <&art 0x0>; +}; + +ð1 { + /* Workaround: keep the Ethernet interfaces order/mapping correct + * (GMAC0 -> eth0, GMAC1 -> eth1, same as in old ar71xx target) + */ + compatible = "qca,qca9530-eth", "syscon", "simple-mfd"; + + mtd-mac-address = <&art 0x6>; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&art 0x0>; + mtd-mac-address-increment = <2>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index 443cccce81..8095712e88 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -230,6 +230,10 @@ netgear,wnr2200-16m) ucidef_set_led_switch "lan3amber" "LAN3 (amber)" "amber:lan3" "switch0" "0x08" "0x02" ucidef_set_led_switch "lan4amber" "LAN4 (amber)" "amber:lan4" "switch0" "0x10" "0x02" ;; +openmesh,om2p-v4) + ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth0" + ucidef_set_led_switch "lan" "LAN" "blue:lan" "switch0" "0x02" + ;; pcs,cr3000) ucidef_set_led_netdev "wan" "WAN" "blue:wan" "eth1" ucidef_set_led_switch "lan1" "LAN1" "blue:lan1" "switch0" "0x04" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 14e858b8fa..fa98b18e59 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -152,6 +152,7 @@ ath79_setup_interfaces() comfast,cf-e120a-v3|\ comfast,cf-e314n-v2|\ compex,wpj531-16m|\ + openmesh,om2p-v4|\ plasmacloud,pa300|\ plasmacloud,pa300e|\ tplink,cpe210-v1|\ diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/openmesh.sh b/target/linux/ath79/generic/base-files/lib/upgrade/openmesh.sh new file mode 100644 index 0000000000..35a4ccfbfe --- /dev/null +++ b/target/linux/ath79/generic/base-files/lib/upgrade/openmesh.sh @@ -0,0 +1,112 @@ +# The U-Boot loader of the OpenMesh devices requires image sizes and +# checksums to be provided in the U-Boot environment. +# The OpenMesh devices come with 2 main partitions - while one is active +# sysupgrade will flash the other. The boot order is changed to boot the +# newly flashed partition. If the new partition can't be booted due to +# upgrade failures the previously used partition is loaded. + +cfg_value_get() +{ + local cfg=$1 cfg_opt + local section=$2 our_section=0 + local param=$3 our_param= + + for cfg_opt in $cfg; do + [ "$cfg_opt" = "[$section]" ] && our_section=1 && continue + [ "$our_section" = "1" ] || continue + + our_param=${cfg_opt%%=*} + [ "$param" = "$our_param" ] && echo ${cfg_opt##*=} && break + done +} + +platform_do_upgrade_openmesh() +{ + local img_path="$1" + local restore_backup + + local setenv_script="/tmp/fw_env_upgrade" + + local inactive_mtd="$(find_mtd_index $PART_NAME)" + local inactive_offset="$(cat /sys/class/mtd/mtd${inactive_mtd}/offset)" + local total_size="$(cat /sys/class/mtd/mtd${inactive_mtd}/size)" + local flash_start_mem=0x9f000000 + local data_offset=$((64 * 1024)) + + # detect to which flash region the new image is written to. + # + # 1. check what is the mtd index for the first flash region on this + # device + # 2. check if the target partition ("inactive") has the mtd index of + # the first flash region + # + # - when it is: the new bootseq will be 1,2 and the first region is + # modified + # - when it isn't: bootseq will be 2,1 and the second region is + # modified + # + # The detection has to be done via the hardcoded mtd partition because + # the current boot might be done with the fallback region. Let us + # assume that the current bootseq is 1,2. The bootloader detected that + # the image in flash region 1 is corrupt and thus switches to flash + # region 2. The bootseq in the u-boot-env is now still the same and + # the sysupgrade code can now only rely on the actual mtd indexes and + # not the bootseq variable to detect the currently booted flash + # region/image. + # + # In the above example, an implementation which uses bootseq ("1,2") to + # detect the currently booted image would assume that region 1 is booted + # and then overwrite the variables for the wrong flash region (aka the + # one which isn't modified). This could result in a device which doesn't + # boot anymore to Linux until it was reflashed with ap51-flash. + local next_boot_part="1" + local primary_kernel_mtd="3" + [ "$inactive_mtd" = "$primary_kernel_mtd" ] || next_boot_part="2" + + local cfg_size=$(dd if="$img_path" bs=2 skip=35 count=4 2>/dev/null) + local cfg_length=$((0x$cfg_size)) + local cfg_content=$(dd if="$img_path" bs=1 skip=$data_offset count=$cfg_length 2>/dev/null) + + local kernel_size=$(dd if="$img_path" bs=2 skip=71 count=4 2>/dev/null) + local kernel_length=$((0x$kernel_size)) + local kernel_md5=$(cfg_value_get "$cfg_content" "vmlinux" "md5sum") + + local rootfs_size=$(dd if="$img_path" bs=2 skip=107 count=4 2>/dev/null) + local rootfs_length=$((0x$rootfs_size)) + local rootfs_md5=$(cfg_value_get "$cfg_content" "rootfs" "md5sum") + local rootfs_checksize=$(cfg_value_get "$cfg_content" "rootfs" "checksize") + + # take care of restoring a saved config + [ -n "$UPGRADE_BACKUP" ] && restore_backup="${MTD_CONFIG_ARGS} -j ${UPGRADE_BACKUP}" + + # write image parts + mtd -q erase inactive + dd if="$img_path" bs=1 skip=$((data_offset + cfg_length + kernel_length)) count=$rootfs_length 2>&- | \ + mtd -n -p $kernel_length $restore_backup write - $PART_NAME + dd if="$img_path" bs=1 skip=$((data_offset + cfg_length)) count=$kernel_length 2>&- | \ + mtd -n write - $PART_NAME + + # prepare new u-boot env + if [ "$next_boot_part" = "1" ]; then + echo "bootseq 1,2" > $setenv_script + else + echo "bootseq 2,1" > $setenv_script + fi + + printf "kernel_size_%i %i\n" $next_boot_part $((kernel_length / 1024)) >> $setenv_script + printf "vmlinux_start_addr 0x%08x\n" $((flash_start_mem + inactive_offset)) >> $setenv_script + printf "vmlinux_size 0x%08x\n" ${kernel_length} >> $setenv_script + printf "vmlinux_checksum %s\n" ${kernel_md5} >> $setenv_script + + printf "rootfs_size_%i %i\n" $next_boot_part $(((total_size-kernel_length) / 1024)) >> $setenv_script + printf "rootfs_start_addr 0x%08x\n" $((flash_start_mem+inactive_offset+kernel_length)) >> $setenv_script + printf "rootfs_size %s\n" $rootfs_checksize >> $setenv_script + printf "rootfs_checksum %s\n" ${rootfs_md5} >> $setenv_script + + # store u-boot env changes + mkdir -p /var/lock + fw_setenv -s $setenv_script || { + echo "failed to update U-Boot environment" + return 1 + } +} diff --git a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh index 98861685dc..88dac75301 100644 --- a/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/generic/base-files/lib/upgrade/platform.sh @@ -50,6 +50,10 @@ platform_do_upgrade() { jjplus,ja76pf2) redboot_fis_do_upgrade "$1" linux ;; + openmesh,om2p-v4) + PART_NAME="inactive" + platform_do_upgrade_openmesh "$1" + ;; plasmacloud,pa300|\ plasmacloud,pa300e) PART_NAME="inactive" diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 63a07a9d5c..132bde73c4 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1557,6 +1557,26 @@ define Device/ocedo_ursus endef TARGET_DEVICES += ocedo_ursus +define Device/openmesh_om2p-common + DEVICE_VENDOR := OpenMesh + DEVICE_PACKAGES := uboot-envtools + IMAGE_SIZE := 7168k + BLOCKSIZE := 256k + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma | \ + pad-to $$(BLOCKSIZE) + IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | \ + openmesh-image ce_type=OM2P | append-metadata +endef + +define Device/openmesh_om2p-v4 + $(Device/openmesh_om2p-common) + SOC := qca9533 + DEVICE_MODEL := OM2P + DEVICE_VARIANT := v4 + SUPPORTED_DEVICES += om2pv4 +endef +TARGET_DEVICES += openmesh_om2p-v4 + define Device/openmesh_om5p-ac-v2 SOC := qca9558 DEVICE_VENDOR := OpenMesh