From: Piotr Dymacz Date: Mon, 11 Mar 2019 17:50:42 +0000 (+0100) Subject: ath79: add support for TP-Link RE350K v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=db91418766562fde7da468a19c87f25bc8aad8a0;p=openwrt%2Fstaging%2Frmilecki.git ath79: add support for TP-Link RE350K v1 TP-Link RE350K v1 (FCC ID: TE7RE350K) is a wall-plug AC1200 Wi-Fi range extender with 'Kasa Smart' support. Device is based on Qualcomm/Atheros QCA9558 + QCA9882 + AR8035 platform and is available only on US market. Specification: - 720/600/200 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of flash (SPI NOR) - 1x 1 Gbps Ethernet (AR8035) - 2T2R 2.4 GHz (QCA9558), with ext. PA (SE2565T) and LNA (SKY65971-11) - 2T2R 5 GHz (QCA9882), with ext. PA (SE5003L1-R) and LNA (SKY65981-11) - 2x U.FL connector on PCB - 2x dual-band PCB antennas - 1x LED, 2x dual-color LED (all driven by GPIO) - 3x button (app config, led, reset) - 1x mechanical on/off slide switch - 1x UART (4-pin, 2.54 mm pitch) header on PCB - 1x JTAG (8-pin, 1.27 mm pitch) header on PCB Flash instruction: Use 'factory' image directly in vendor GUI (default IP: 192.168.0.254, default credentials: admin/admin). Warning: This device does not include any kind of recovery mechanism in U-Boot. Vendor firmware access: You can access vendor firmware over serial (RX line requires jumper resistor in R306 place, near XTAL) with: root/sohoadmin credentials. Signed-off-by: Piotr Dymacz --- diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 76a1ffba409..e66eb938fdb 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -18,6 +18,7 @@ ath79_setup_interfaces() pcs,cap324|\ pisen,wmm003n|\ pqi,air-pen|\ + tplink,re350k-v1|\ tplink,re450-v2|\ tplink,tl-mr10u|\ tplink,tl-mr3020-v1|\ diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 53128cad65e..501a4755718 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -141,6 +141,10 @@ case "$FIRMWARE" in ath10kcal_extract "art" 20480 2116 ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) -1) ;; + tplink,re350k-v1) + ath10kcal_extract "art" 20480 2116 + ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +2) + ;; ubnt,unifiac-lite|\ ubnt,unifiac-mesh|\ ubnt,unifiac-mesh-pro|\ diff --git a/target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts b/target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts new file mode 100644 index 00000000000..056b513d7e0 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_tplink_re350k-v1.dts @@ -0,0 +1,173 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca9557.dtsi" + +/ { + model = "TP-Link RE350K v1"; + compatible = "tplink,re350k-v1", "qca,qca9558"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + mdio-gpio0 = &mdio2; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + keys { + compatible = "gpio-keys"; + + app-config { + label = "app-config"; + linux,code = ; + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + led { + label = "led"; + linux,code = ; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; + + leds { + compatible = "gpio-leds"; + + power: power { + label = "tp-link:green:power"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wlan2g-green { + label = "tp-link:green:wlan2g"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan2g-red { + label = "tp-link:red:wlan2g"; + gpios = <&gpio 21 GPIO_ACTIVE_LOW>; + }; + + wlan5g-green { + label = "tp-link:green:wlan5g"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g-red { + label = "tp-link:red:wlan5g"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + }; + + mdio2: mdio { + compatible = "virtual,mdio-gpio"; + + #address-cells = <1>; + #size-cells = <0>; + + gpios = <&gpio 23 GPIO_ACTIVE_HIGH>, + <&gpio 18 GPIO_ACTIVE_HIGH>; + + phy0: ethernet-phy@4 { + reg = <4>; + + phy-mode = "rgmii-rxid"; + at803x-disable-smarteee; + }; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&config 0x10008>; + pll-data = <0x9e000000 0x80000101 0x80001313>; + phy-handle = <&phy0>; + + gmac-config { + device = <&gmac>; + + rxdv-delay = <2>; + rxd-delay = <2>; + txen-delay = <0>; + txd-delay = <0>; + rgmii-enabled = <1>; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x020000>; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x020000 0xd70000>; + }; + + config: partition@d90000 { + label = "config"; + reg = <0xd90000 0x260000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&uart { + status = "okay"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&config 0x10008>; +}; diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index 5933988632d..e82a5a30739 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -109,6 +109,22 @@ define Device/tplink_archer-c7-v5 endef TARGET_DEVICES += tplink_archer-c7-v5 +define Device/tplink_re350k-v1 + $(Device/tplink) + ATH_SOC := qca9558 + IMAGE_SIZE := 13760k + DEVICE_TITLE := TP-Link RE350K v1 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct + TPLINK_BOARD_ID := RE350K-V1 + TPLINK_HWID := 0x0 + TPLINK_HWREV := 0 + KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header -O + IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \ + check-size $$$$(IMAGE_SIZE) | append-metadata + IMAGE/factory.bin := append-rootfs | tplink-safeloader factory +endef +TARGET_DEVICES += tplink_re350k-v1 + define Device/tplink_re450-v2 $(Device/tplink) ATH_SOC := qca9563 diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 075cd8a7edd..c2aa2962f67 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -1144,6 +1144,38 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system" }, + /** Firmware layout for the RE350K v1 */ + { + .id = "RE350K-V1", + .vendor = "", + .support_list = + "SupportList:\n" + "{product_name:RE350K,product_ver:1.0.0,special_id:00000000,product_region:US}\n", + .support_trail = '\x00', + .soft_ver = NULL, + + /** We're using a dynamic kernel/rootfs split here */ + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"firmware", 0x20000, 0xd70000}, + {"partition-table", 0xd90000, 0x02000}, + {"default-mac", 0xda0000, 0x00020}, + {"pin", 0xda0100, 0x00020}, + {"product-info", 0xda1100, 0x01000}, + {"soft-version", 0xdb0000, 0x01000}, + {"support-list", 0xdb1000, 0x01000}, + {"profile", 0xdb2000, 0x08000}, + {"user-config", 0xdc0000, 0x10000}, + {"default-config", 0xdd0000, 0x10000}, + {"device-id", 0xde0000, 0x00108}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system" + }, + /** Firmware layout for the RE355 */ { .id = "RE355",