From: Lauro Moreno Date: Wed, 28 Oct 2020 20:59:47 +0000 (-0600) Subject: ipq806x: add support for Askey RT4230W REV6 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=da8428d277cd3373b05330cb3b4f93aef717c5ab;p=openwrt%2Fstaging%2Fynezz.git ipq806x: add support for Askey RT4230W REV6 This adds support for the Askey RT4230W REV6 (Branded by Spectrum/Charter as RAC2V1K) At this time, there's no way to reinstall the stock firmware so don't install this on a router that's being rented. Specifications: Qualcomm IPQ8065 1 GB of RAM (DDR3) 512 MB Flash (NAND) 2x Wave 2 WiFi cards (QCA9984) 5x 10/100/1000 Mbps Ethernet (Switch: QCA8337) 1x LED (Controlled by a microcontroller that switches it between red and blue with different patterns) 1x USB 3.0 Type-A 12V DC Power Input UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V Port settings are 115200n8 More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830 https://deviwiki.com/wiki/Askey_RAC2V1K To check what revision your router is, restore one of these config backups through the stock firmware to get ssh access then run "cat /proc/device-tree/model". https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17 The revision number on the board doesn't seem to be very consistent so that's why this is needed. You can also run printenv in the uboot console and if machid is set to 177d, that means your router is rev6. Note: Don't install this if the router is being rented from an ISP. The defined partition layout is different from the OEM one and even if you changed the layout to match, backing up and restoring the OEM firmware breaks /overlay so nothing will save and the router will likely enter a bootloop. How to install: Method 1: Install without opening the case using SSH and tftp You'll need: RAC2V1K-SSH.zip: https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip initramfs and sysupgrade images Connect to one of the router's LAN ports Download the RAC2V1K-SSH.zip file and restore the config file that corresponds to your router's firmware (If you're firmware is newer than what's in the zip file, just restore the 1.1.16 file) After a reboot, you should be able to ssh into the router with username: "4230w" and password: "linuxbox" or "admin". Run the following commannds fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as it's in the same subnet as the server fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next steps fw_setenv bootdelay 8 fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq" Don't reboot the router yet. Install and set up a tftp server on your computer Set a static ip on the ethernet interface of your computer (use this for serverip in the above commands) Rename the initramfs image to initramfs.bin, and host it with the tftp server Reboot the router. If you set up everything right, the router led should switch over to a slow blue glow which means openwrt is booted. If for some reason the file doesn't get loaded into ram properly, it should still boot to the OEM firmware. After openwrt boots, ssh into it and run these commands: fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" fw_setenv bootdelay 2 After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Method 2: Install with serial access (Do this if something fails and you can't boot after using method 1) You'll need: initramfs and sysupgrade images Serial access: https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case Install and set up a tftp server Set a static ip on the ethernet interface of your computer Download the initramfs image, rename it to initramfs.bin, and host it with the tftp server Connect the wan port of the router to your computer Interrupt U-Boot and run these commands: setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer) setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet) setenv bootcmd "setenv mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" saveenv tftpboot initramfs.bin bootm After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Signed-off-by: Lauro Moreno [add entry in 5.10 patch, fix whitespace issues] Signed-off-by: Adrian Schmutzler --- diff --git a/package/boot/uboot-envtools/files/ipq806x b/package/boot/uboot-envtools/files/ipq806x index 222d801f17..7e1d71a7e9 100644 --- a/package/boot/uboot-envtools/files/ipq806x +++ b/package/boot/uboot-envtools/files/ipq806x @@ -30,6 +30,9 @@ ubootenv_mtdinfo () { } case "$board" in +askey,rt4230w-rev6) + ubootenv_add_uci_config "/dev/mtd9" "0x0" "0x40000" "0x20000" + ;; edgecore,ecw5410) ubootenv_add_uci_config "/dev/mtd11" "0x0" "0x10000" "0x10000" ;; diff --git a/target/linux/ipq806x/base-files/etc/board.d/02_network b/target/linux/ipq806x/base-files/etc/board.d/02_network index abdab89857..22d607b0ec 100644 --- a/target/linux/ipq806x/base-files/etc/board.d/02_network +++ b/target/linux/ipq806x/base-files/etc/board.d/02_network @@ -11,6 +11,7 @@ board_config_update board=$(board_name) case "$board" in +askey,rt4230w-rev6 |\ asrock,g10 |\ nec,wg2600hp) ucidef_add_switch "switch0" \ diff --git a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index fca35516ec..5592590d52 100644 --- a/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq806x/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -9,6 +9,7 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/pre-cal-pci-0000:01:00.0.bin") case $board in + askey,rt4230w-rev6 |\ asrock,g10) if [ -b "$(find_mtd_part 0:art)" ]; then caldata_extract "0:art" 0x1000 0x2f20 @@ -68,6 +69,7 @@ case "$FIRMWARE" in ;; "ath10k/pre-cal-pci-0001:01:00.0.bin") case $board in + askey,rt4230w-rev6 |\ asrock,g10) if [ -b "$(find_mtd_part 0:art)" ]; then caldata_extract "0:art" 0x5000 0x2f20 diff --git a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh index 4dc612492c..a5e18201df 100644 --- a/target/linux/ipq806x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq806x/base-files/lib/upgrade/platform.sh @@ -10,15 +10,7 @@ platform_check_image() { platform_do_upgrade() { case "$(board_name)" in - asrock,g10) - asrock_upgrade_prepare - nand_do_upgrade "$1" - ;; - buffalo,wxr-2533dhp) - buffalo_upgrade_prepare_ubi - CI_ROOTPART="ubi_rootfs" - nand_do_upgrade "$1" - ;; + askey,rt4230w-rev6 |\ compex,wpq864|\ netgear,d7800 |\ netgear,r7500 |\ @@ -28,6 +20,15 @@ platform_do_upgrade() { qcom,ipq8064-ap161) nand_do_upgrade "$1" ;; + asrock,g10) + asrock_upgrade_prepare + nand_do_upgrade "$1" + ;; + buffalo,wxr-2533dhp) + buffalo_upgrade_prepare_ubi + CI_ROOTPART="ubi_rootfs" + nand_do_upgrade "$1" + ;; edgecore,ecw5410) part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')" if [ "$part" = "rootfs1" ]; then diff --git a/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-rt4230w-rev6.dts b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-rt4230w-rev6.dts new file mode 100644 index 0000000000..7342de4bec --- /dev/null +++ b/target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-rt4230w-rev6.dts @@ -0,0 +1,303 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "qcom-ipq8065.dtsi" +#include + +/ { + model = "Askey RT4230W REV6"; + compatible = "askey,rt4230w-rev6", "qcom,ipq8065", "qcom,ipq8064"; + + memory@0 { + reg = <0x42000000 0x3e000000>; + device_type = "memory"; + }; + + aliases { + led-boot = &ledctrl3; + led-failsafe = &ledctrl1; + led-running = &ledctrl2; + led-upgrade = &ledctrl3; + }; + + chosen { + bootargs = "rootfstype=squashfs noinitrd"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + reset { + label = "reset"; + gpios = <&qcom_pinmux 54 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&qcom_pinmux 68 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&led_pins>; + pinctrl-names = "default"; + + ledctrl1: ledctrl1 { + label = "ledctrl1"; + gpios = <&qcom_pinmux 22 GPIO_ACTIVE_HIGH>; + }; + + ledctrl2: ledctrl2 { + label = "ledctrl2"; + gpios = <&qcom_pinmux 23 GPIO_ACTIVE_HIGH>; + }; + + ledctrl3: ledctrl3 { + label = "ledctrl3"; + gpios = <&qcom_pinmux 24 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&qcom_pinmux { + button_pins: button_pins { + mux { + pins = "gpio54", "gpio68"; + function = "gpio"; + drive-strength = <2>; + bias-pull-up; + }; + }; + + led_pins: led_pins { + mux { + pins = "gpio22", "gpio23", "gpio24"; + function = "gpio"; + drive-strength = <2>; + bias-pull-down; + }; + }; + + rgmii2_pins: rgmii2_pins { + mux { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", + "gpio51", "gpio52", "gpio59", "gpio60", "gpio61", "gpio62"; + function = "rgmii2"; + drive-strength = <8>; + bias-disable; + }; + + tx { + pins = "gpio27", "gpio28", "gpio29", "gpio30", "gpio31", "gpio32"; + input-disable; + }; + }; +}; + +&nand_controller { + status = "okay"; + + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + + nand@0 { + reg = <0>; + compatible = "qcom,nandcs"; + + nand-ecc-strength = <4>; + nand-bus-width = <8>; + nand-ecc-step-size = <512>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0000000 0x0040000>; + read-only; + }; + partition@40000 { + label = "0:MIBIB"; + reg = <0x0040000 0x0140000>; + read-only; + }; + partition@180000 { + label = "0:SBL2"; + reg = <0x0180000 0x0140000>; + read-only; + }; + partition@2c0000 { + label = "0:SBL3"; + reg = <0x02c0000 0x0280000>; + read-only; + }; + partition@540000 { + label = "0:DDRCONFIG"; + reg = <0x0540000 0x0120000>; + read-only; + }; + partition@660000 { + label = "0:SSD"; + reg = <0x0660000 0x0120000>; + read-only; + }; + partition@780000 { + label = "0:TZ"; + reg = <0x0780000 0x0280000>; + read-only; + }; + partition@a00000 { + label = "0:RPM"; + reg = <0x0a00000 0x0280000>; + read-only; + }; + partition@c80000 { + label = "0:APPSBL"; + reg = <0x0c80000 0x0500000>; + read-only; + }; + partition@1180000 { + label = "0:APPSBLENV"; + reg = <0x1180000 0x0080000>; + }; + ART: partition@1200000 { + label = "0:ART"; + reg = <0x1200000 0x0140000>; + read-only; + }; + partition@1340000 { + label = "0:BOOTCONFIG"; + reg = <0x1340000 0x0060000>; + read-only; + }; + partition@13a0000 { + label = "0:SBL2_1"; + reg = <0x13a0000 0x0140000>; + read-only; + }; + partition@14e0000 { + label = "0:SBL3_1"; + reg = <0x14e0000 0x0280000>; + read-only; + }; + partition@1760000 { + label = "0:DDRCONFIG_1"; + reg = <0x1760000 0x0120000>; + read-only; + }; + partition@1880000 { + label = "0:SSD_1"; + reg = <0x1880000 0x0120000>; + read-only; + }; + partition@19a0000 { + label = "0:TZ_1"; + reg = <0x19a0000 0x0280000>; + read-only; + }; + partition@1c20000 { + label = "0:RPM_1"; + reg = <0x1c20000 0x0280000>; + read-only; + }; + partition@1ea0000 { + label = "0:BOOTCONFIG1"; + reg = <0x1ea0000 0x0060000>; + read-only; + }; + partition@1f00000 { + label = "0:APPSBL_1"; + reg = <0x1f00000 0x0500000>; + read-only; + }; + partition@2400000 { + label = "ubi"; + reg = <0x2400000 0x1a000000>; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-0 = <&mdio0_pins>; + pinctrl-names = "default"; + + phy0: ethernet-phy@0 { + reg = <0x0>; + qca,ar8327-initvals = < + 0x00004 0x7600000 /* PAD0_MODE */ + 0x00008 0x1000000 /* PAD5_MODE */ + 0x0000c 0x80 /* PAD6_MODE */ + 0x000e4 0xaa545 /* MAC_POWER_SEL */ + 0x000e0 0xc74164de /* SGMII_CTRL */ + 0x0007c 0x4e /* PORT0_STATUS */ + 0x00094 0x4e /* PORT6_STATUS */ + 0x00050 0xcf02cf02 /* LED_CTRL_0 */ + 0x00054 0xc832c832 /* LED_CTRL_1 */ + >; + }; +}; + +&gmac0 { + status = "okay"; + phy-mode = "rgmii"; + qcom,id = <0>; + + mtd-mac-address = <&ART 0x0>; + + pinctrl-0 = <&rgmii2_pins>; + pinctrl-names = "default"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "sgmii"; + qcom,id = <1>; + + mtd-mac-address = <&ART 0x6>; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&adm_dma { + status = "okay"; +}; + +&usb3_0 { + status = "okay"; + clocks = <&gcc USB30_1_MASTER_CLK>; +}; + +&usb3_1 { + status = "okay"; + clocks = <&gcc USB30_0_MASTER_CLK>; +}; + +&pcie0 { + status = "okay"; + reset-gpio = <&qcom_pinmux 3 GPIO_ACTIVE_HIGH>; + /delete-property/ perst-gpios; +}; + +&pcie1 { + status = "okay"; + reset-gpio = <&qcom_pinmux 48 GPIO_ACTIVE_HIGH>; + /delete-property/ perst-gpios; + force_gen1 = <1>; +}; diff --git a/target/linux/ipq806x/image/Makefile b/target/linux/ipq806x/image/Makefile index 6c091be335..e53fba1e1d 100644 --- a/target/linux/ipq806x/image/Makefile +++ b/target/linux/ipq806x/image/Makefile @@ -90,6 +90,19 @@ define Device/ZyXELImage IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to $$$$(BLOCKSIZE) | sysupgrade-tar rootfs=$$$$@ | append-metadata endef +define Device/askey_rt4230w-rev6 + $(call Device/LegacyImage) + DEVICE_VENDOR := Askey + DEVICE_MODEL := RT4230W + DEVICE_VARIANT := REV6 + SOC := qcom-ipq8065 + BLOCKSIZE := 128k + PAGESIZE := 2048 + DEVICE_PACKAGES := ath10k-firmware-qca9984-ct + KERNEL_IN_UBI := 1 +endef +TARGET_DEVICES += askey_rt4230w-rev6 + define Device/asrock_g10 $(call Device/FitImage) $(call Device/UbiFit) diff --git a/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch index a8e17afd42..87d6b65694 100644 --- a/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -907,8 +907,25 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -907,8 +907,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ @@ -32,6 +32,7 @@ Signed-off-by: John Crispin + qcom-ipq8064-wxr-2533dhp.dtb \ + qcom-ipq8065-nbg6817.dtb \ + qcom-ipq8065-r7800.dtb \ ++ qcom-ipq8065-rt4230w-rev6.dtb \ + qcom-ipq8068-ecw5410.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \ diff --git a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch index 055a4cbc30..b97d36fd7c 100644 --- a/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch +++ b/target/linux/ipq806x/patches-5.4/0069-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -842,7 +842,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -842,7 +842,25 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4019-ap.dk04.1-c3.dtb \ qcom-ipq4019-ap.dk07.1-c1.dtb \ qcom-ipq4019-ap.dk07.1-c2.dtb \ @@ -31,6 +31,7 @@ Signed-off-by: John Crispin + qcom-ipq8064-wxr-2533dhp.dtb \ + qcom-ipq8065-nbg6817.dtb \ + qcom-ipq8065-r7800.dtb \ ++ qcom-ipq8065-rt4230w-rev6.dtb \ + qcom-ipq8068-ecw5410.dtb \ qcom-msm8660-surf.dtb \ qcom-msm8960-cdp.dtb \