From: David Bentham Date: Fri, 10 Nov 2023 18:50:38 +0000 (+0000) Subject: mediatek: add Comfast CF-E393AX support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=d8f4453bf2de9fd9baf3d660ed12e0797ff2cfdb;p=openwrt%2Fstaging%2Fthess.git mediatek: add Comfast CF-E393AX support Comfast CF-E393AX is a dual-band Wi-Fi 6 POE ceiling mount access point. Oem firmware is a custom openwrt 21.02 snapshot version. We can gain access via ssh once we remove the root password. Hardware specification: SoC: MediaTek MT7981A 2x A53 Flash: 128 MB SPI-NAND RAM: 256MB DDR3 Ethernet: 1x 10/100/1000 Mbps built-in PHY (WAN) 1x 10/100/1000/2500 Mbps MaxLinear GPY211C (LAN) Switch: MediaTek MT7531AE WiFi: MediaTek MT7976D LEDS: 1x (Red, Blue and Green) Button: Reset UART: 3.3v, 115200n8 -------------------------- | Layout | | ----------------- | | 4 | VCC GND TX RX | <= | | ----------------- | -------------------------- Gain SSH access: 1. Login into web interface (http://apipaddress/computer/login.html), and download the configuration(http://apipaddress/computer/config.html). 2. Rename downloaded backup config - 'backup.file to backup.tar.gz', Enter 'fakeroot' command then decompress the configuration: tar -zxf backup.tar.gz 3. Edit 'etc/shadow', update (remove) root password: With password = 'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::' 'root:$1$xf7D0Hfg$5gkjmvgQe4qJbe1fi/VLy1:19362:0:99999:7:::' to Without password = 'root::0:99999:7:::' 'root::0:99999:7:::' 4. Repack 'etc' directory back to a new backup file: tar -zcf backup-ssh.tar.gz etc/ 5. Rename new config tar.gz file to 'backup-ssh.file' Exit fakeroot - 'exit' 6. Upload new configuration via web interface, now you can SSH with the following: 'ssh -vv -o HostKeyAlgorithms=+ssh-rsa \ -o PubkeyAcceptedAlgorithms=+ssh-rsa root@192.168.10.1'. Backup the mtd partitions - https://openwrt.org/docs/guide-user/installation/generic.backup 7. Copy openwrt factory firmware to the tmp folder to install via ssh: 'scp -o HostKeyAlgorithms=+ssh-rsa \ -o PubkeyAcceptedAlgorithms=+ssh-rsa \ *-mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin \ root@192.168.10.1:/tmp/' 'sysupgrade -n -F \ /tmp/*--mediatek-filogic-comfast_cf-e393ax-squashfs-factory.bin' 8. Once led has stopped flashing - Connect via ssh with the default openwrt ip address - 'ssh root@192.168.1.1' 9. SSH copy the openwrt sysupgrade firmware and upgrade as per the default instructions. Signed-off-by: David Bentham --- diff --git a/package/boot/uboot-envtools/files/mediatek_filogic b/package/boot/uboot-envtools/files/mediatek_filogic index 4c483ca614..17a63302c2 100644 --- a/package/boot/uboot-envtools/files/mediatek_filogic +++ b/package/boot/uboot-envtools/files/mediatek_filogic @@ -57,6 +57,9 @@ cmcc,rax3000m) ;; esac ;; +comfast,cf-e393ax) + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x80000" + ;; cetron,ct3003|\ netgear,wax220|\ zbtlink,zbt-z8102ax|\ diff --git a/target/linux/mediatek/dts/mt7981a-comfast-cf-e393ax.dts b/target/linux/mediatek/dts/mt7981a-comfast-cf-e393ax.dts new file mode 100644 index 0000000000..7445b610dc --- /dev/null +++ b/target/linux/mediatek/dts/mt7981a-comfast-cf-e393ax.dts @@ -0,0 +1,250 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; +#include "mt7981.dtsi" + +/ { + model = "COMFAST CF-E393AX"; + compatible = "comfast,cf-e393ax", "mediatek,mt7981"; + + aliases { + serial0 = &uart0; + led-boot = &led_red; + led-failsafe = &led_red; + led-running = &led_blue; + led-upgrade = &led_green; + }; + + chosen { + bootargs-override = "console=ttyS0,115200n8"; + stdout-path = "serial0:115200n8"; + }; + + memory { + reg = <0 0x40000000 0 0x10000000>; // 256mb + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_blue: blue { + label = "blue:status"; + gpios = <&pio 8 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_red: red { + label = "red:status"; + gpios = <&pio 34 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_STATUS; + }; + + led_green: green { + label = "green:status"; + gpios = <&pio 35 GPIO_ACTIVE_LOW>; + color = ; + function = LED_FUNCTION_STATUS; + }; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + /* LAN */ + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + nvmem-cells = <&macaddr_factory_e000 0>; + nvmem-cell-names = "mac-address"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + /* WAN */ + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + nvmem-cells = <&macaddr_factory_e000 1>; + nvmem-cell-names = "mac-address"; + }; +}; + +&mdio_bus { + switch: switch@1f { + compatible = "mediatek,mt7531"; + reg = <31>; + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&pio>; + interrupts = <38 IRQ_TYPE_LEVEL_HIGH>; + reset-gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + }; +}; + +&crypto { + status = "okay"; +}; + +&pio { + spi0_flash_pins: spi0-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + conf-pu { + pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP"; + drive-strength = ; + bias-pull-up = ; + }; + conf-pd { + pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO"; + drive-strength = ; + bias-pull-down = ; + }; + }; + +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_flash_pins>; + cs-gpios = <0>, <0>; + #address-cells = <1>; + #size-cells = <0>; + status = "okay"; + #address-cells = <1>; + #size-cells = <0>; + + spi_nand: spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <52000000>; + + spi-cal-enable; + spi-cal-mode = "read-data"; + spi-cal-datalen = <7>; + spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4E 0x41 0x4E 0x44>; + spi-cal-addrlen = <5>; + spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>; + + spi-tx-bus-width = <4>; + spi-rx-bus-width = <4>; + mediatek,nmbm; + mediatek,bmt-max-ratio = <1>; + mediatek,bmt-max-reserved-blocks = <64>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "BL2"; + reg = <0x00000 0x0100000>; + read-only; + }; + + partition@100000 { + label = "u-boot-env"; + reg = <0x0100000 0x0080000>; + read-only; + }; + + factory: partition@180000 { + label = "Factory"; + reg = <0x180000 0x0200000>; + read-only; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + macaddr_factory_e000: macaddr@e000 { + compatible = "mac-base"; + reg = <0xe000 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + + partition@380000 { + label = "FIP"; + reg = <0x380000 0x0200000>; + read-only; + }; + + partition@580000 { + label = "ubi"; + reg = <0x580000 0x4000000>; + compatible = "linux,ubi"; + }; + }; + }; +}; + +&switch { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; +}; + diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index a198fb98c9..a9cf0d2305 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -40,6 +40,9 @@ mediatek_setup_interfaces() zbtlink,zbt-z8103ax) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" eth1 ;; + comfast,cf-e393ax) + ucidef_set_interfaces_lan_wan "lan1" eth1 + ;; glinet,gl-mt2500|\ glinet,gl-mt3000) ucidef_set_interfaces_lan_wan eth1 eth0 diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index 937d39066c..1f00e9b285 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -57,6 +57,10 @@ case "$board" in esac [ "$PHYNBR" = "1" ] && echo "$addr" > /sys${DEVPATH}/macaddress ;; + comfast,cf-e393ax) + addr=$(mtd_get_mac_binary "Factory" 0x8000) + [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress + ;; cudy,wr3000-v1) addr=$(mtd_get_mac_binary bdinfo 0xde00) # Originally, phy0 is phy1 mac with LA bit set. However, this would conflict diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index c64a46fe24..90a0e91f02 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -322,6 +322,30 @@ define Device/cmcc_rax3000m endef TARGET_DEVICES += cmcc_rax3000m +define Device/comfast_cf-e393ax + DEVICE_VENDOR := Comfast + DEVICE_MODEL := CF-E393AX + DEVICE_DTS := mt7981a-comfast-cf-e393ax + DEVICE_DTS_DIR := ../dts + DEVICE_DTC_FLAGS := --pad 4096 + DEVICE_DTS_LOADADDR := 0x43f00000 + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware + KERNEL_LOADADDR := 0x44000000 + KERNEL = kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + KERNEL_INITRAMFS = kernel-bin | lzma | \ + fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd + UBINIZE_OPTS := -E 5 + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + KERNEL_IN_UBI := 1 + IMAGES := sysupgrade.bin factory.bin + IMAGE/factory.bin := append-ubi | check-size $$$$(IMAGE_SIZE) + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef +TARGET_DEVICES += comfast_cf-e393ax + define Device/confiabits_mt7981 DEVICE_VENDOR := Confiabits DEVICE_MODEL := MT7981