From: Christian Lamparter <chunkeey@gmail.com>
Date: Sat, 27 Nov 2021 22:06:13 +0000 (+0100)
Subject: ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUP
X-Git-Tag: v22.03.0-rc1~1023
X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=d641a604789ac604b01b9a7b408614e1cb74c700;p=openwrt%2Fstaging%2Fhauke.git

ipq40xx: nvmem cells for EZVIZ CS-W3-WD1200G EUP

introduce nvmem pre-cal + mac-address cells for both Wifis
and ethernet on the EZVIZ CS-W3-WD1200G EUP. This is one of
the few devices in which the correct mac adress is already
at the right place for Wifi, so no separate nvmem cell is
needed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
---

diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8924fb3258..d368475ffc 100644
--- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -64,7 +64,6 @@ case "$FIRMWARE" in
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
-	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-ap1300 |\
 	glinet,gl-b1300 |\
 	glinet,gl-b2200 |\
@@ -187,7 +186,6 @@ case "$FIRMWARE" in
 	8dev,jalapeno |\
 	alfa-network,ap120c-ac |\
 	cilab,meshpoint-one |\
-	ezviz,cs-w3-wd1200g-eup |\
 	glinet,gl-ap1300 |\
 	glinet,gl-b1300 |\
 	glinet,gl-b2200 |\
diff --git a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
index 1b8454e4c5..d1fcd804d9 100644
--- a/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
+++ b/target/linux/ipq40xx/base-files/lib/preinit/05_set_iface_mac_ipq40xx.sh
@@ -7,10 +7,6 @@ preinit_set_mac_address() {
 		ip link set dev eth0 address $(macaddr_add "$base_mac" 1)
 		ip link set dev eth1 address $(macaddr_add "$base_mac" 3)
 		;;
-	ezviz,cs-w3-wd1200g-eup)
-		ip link set dev eth0 address $(mtd_get_mac_binary "ART" 0x6)
-		ip link set dev eth1 address $(mtd_get_mac_binary "ART" 0x0)
-		;;
 	engenius,eap2200)
 		base_mac=$(cat /sys/class/net/eth0/address)
 		ip link set dev eth1 address $(macaddr_add "$base_mac" 1)
diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cs-w3-wd1200g-eup.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cs-w3-wd1200g-eup.dts
index 062826c7a4..52311755b7 100644
--- a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cs-w3-wd1200g-eup.dts
+++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-cs-w3-wd1200g-eup.dts
@@ -210,6 +210,26 @@
 				label = "ART";
 				reg = <0x00170000 0x00010000>;
 				read-only;
+
+				compatible = "nvmem-cells";
+				#address-cells = <1>;
+				#size-cells = <1>;
+
+				macaddr_art_0: macaddr@0 {
+					reg = <0x0 0x6>;
+				};
+
+				macaddr_art_6: macaddr@6 {
+					reg = <0x6 0x6>;
+				};
+
+				precal_art_1000: precal@1000 {
+					reg = <0x1000 0x2f20>;
+				};
+
+				precal_art_5000: precal@5000 {
+					reg = <0x5000 0x2f20>;
+				};
 			};
 
 			partition9@580000 {
@@ -234,9 +254,23 @@
 &wifi0 {
 	status = "okay";
 	qcom,ath10k-calibration-variant = "ezviz-cs-w3-wd1200g-eup";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_1000>;
 };
 
 &wifi1 {
 	status = "okay";
 	qcom,ath10k-calibration-variant = "ezviz-cs-w3-wd1200g-eup";
+	nvmem-cell-names = "pre-calibration";
+	nvmem-cells = <&precal_art_5000>;
+};
+
+&gmac0 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&macaddr_art_6>;
+};
+
+&gmac1 {
+	nvmem-cell-names = "mac-address";
+	nvmem-cells = <&macaddr_art_0>;
 };