From: Florian Fainelli Date: Sun, 17 Mar 2013 14:33:23 +0000 (+0000) Subject: ep93xx: remove 3.3 kernel support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=d5c2e83fa53f902a6d0093c6901b869a99c8de3b;p=openwrt%2Fstaging%2Fynezz.git ep93xx: remove 3.3 kernel support Signed-off-by: Florian Fainelli SVN-Revision: 36064 --- diff --git a/target/linux/ep93xx/config-3.3 b/target/linux/ep93xx/config-3.3 deleted file mode 100644 index 69c94d37dd..0000000000 --- a/target/linux/ep93xx/config-3.3 +++ /dev/null @@ -1,196 +0,0 @@ -CONFIG_ALIGNMENT_TRAP=y -CONFIG_ARCH_BINFMT_ELF_RANDOMIZE_PIE=y -CONFIG_ARCH_EP93XX=y -CONFIG_ARCH_HAS_CPU_IDLE_WAIT=y -CONFIG_ARCH_HAS_HOLES_MEMORYMODEL=y -CONFIG_ARCH_NR_GPIO=0 -CONFIG_ARCH_REQUIRE_GPIOLIB=y -# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set -# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set -CONFIG_ARCH_SUSPEND_POSSIBLE=y -CONFIG_ARCH_USES_GETTIMEOFFSET=y -CONFIG_ARM=y -CONFIG_ARM_AMBA=y -# CONFIG_ARM_CPU_SUSPEND is not set -CONFIG_ARM_L1_CACHE_SHIFT=5 -CONFIG_ARM_NR_BANKS=16 -CONFIG_ARM_PATCH_PHYS_VIRT=y -# CONFIG_ARM_SP805_WATCHDOG is not set -CONFIG_ARM_THUMB=y -CONFIG_ARM_VIC=y -CONFIG_ARM_VIC_NR=2 -# CONFIG_ARPD is not set -# CONFIG_BLK_DEV_INITRD is not set -# CONFIG_CACHE_L2X0 is not set -CONFIG_CC_OPTIMIZE_FOR_SIZE=y -CONFIG_CLKDEV_LOOKUP=y -CONFIG_CMDLINE="console=ttyAM0,57600 init=/etc/preinit" -CONFIG_CMDLINE_FROM_BOOTLOADER=y -CONFIG_CONSOLE_TRANSLATIONS=y -CONFIG_CPU_32v4T=y -CONFIG_CPU_ABRT_EV4T=y -CONFIG_CPU_ARM920T=y -CONFIG_CPU_CACHE_V4WT=y -CONFIG_CPU_CACHE_VIVT=y -CONFIG_CPU_COPY_V4WB=y -CONFIG_CPU_CP15=y -CONFIG_CPU_CP15_MMU=y -# CONFIG_CPU_DCACHE_WRITETHROUGH is not set -# CONFIG_CPU_ICACHE_DISABLE is not set -CONFIG_CPU_PABRT_LEGACY=y -CONFIG_CPU_TLB_V4WBI=y -CONFIG_CPU_USE_DOMAINS=y -CONFIG_CRC7=y -CONFIG_CRC_ITU_T=y -CONFIG_CRUNCH=y -# CONFIG_DEBUG_USER is not set -CONFIG_DUMMY_CONSOLE=y -CONFIG_ELF_CORE=y -# CONFIG_ENABLE_WARN_DEPRECATED is not set -CONFIG_EP93XX_EARLY_UART1=y -# CONFIG_EP93XX_EARLY_UART2 is not set -# CONFIG_EP93XX_EARLY_UART3 is not set -CONFIG_EP93XX_ETH=y -# CONFIG_EP93XX_PWM is not set -CONFIG_EP93XX_SDCE0_PHYS_OFFSET=y -# CONFIG_EP93XX_SDCE1_PHYS_OFFSET is not set -# CONFIG_EP93XX_SDCE2_PHYS_OFFSET is not set -# CONFIG_EP93XX_SDCE3_ASYNC_PHYS_OFFSET is not set -# CONFIG_EP93XX_SDCE3_SYNC_PHYS_OFFSET is not set -CONFIG_EP93XX_WATCHDOG=y -CONFIG_FONTS=y -# CONFIG_FONT_10x18 is not set -# CONFIG_FONT_6x11 is not set -# CONFIG_FONT_7x14 is not set -CONFIG_FONT_8x16=y -CONFIG_FONT_8x8=y -# CONFIG_FONT_ACORN_8x8 is not set -# CONFIG_FONT_MINI_4x6 is not set -# CONFIG_FONT_PEARL_8x8 is not set -# CONFIG_FONT_SUN12x22 is not set -# CONFIG_FONT_SUN8x16 is not set -CONFIG_FRAMEBUFFER_CONSOLE=y -# CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY is not set -# CONFIG_FRAMEBUFFER_CONSOLE_ROTATION is not set -CONFIG_FRAME_POINTER=y -# CONFIG_FW_LOADER is not set -CONFIG_GENERIC_ATOMIC64=y -CONFIG_GENERIC_BUG=y -CONFIG_GENERIC_GPIO=y -CONFIG_GENERIC_IRQ_SHOW=y -CONFIG_GENERIC_PCI_IOMAP=y -CONFIG_GPIOLIB=y -CONFIG_GPIO_EP93XX=y -CONFIG_GPIO_GENERIC=y -# CONFIG_GPIO_PL061 is not set -# CONFIG_HAMRADIO is not set -CONFIG_HARDIRQS_SW_RESEND=y -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HAVE_AOUT=y -CONFIG_HAVE_ARCH_KGDB=y -CONFIG_HAVE_ARCH_PFN_VALID=y -CONFIG_HAVE_CLK=y -CONFIG_HAVE_C_RECORDMCOUNT=y -CONFIG_HAVE_DMA_API_DEBUG=y -CONFIG_HAVE_DYNAMIC_FTRACE=y -CONFIG_HAVE_FTRACE_MCOUNT_RECORD=y -CONFIG_HAVE_FUNCTION_GRAPH_TRACER=y -CONFIG_HAVE_FUNCTION_TRACER=y -CONFIG_HAVE_GENERIC_DMA_COHERENT=y -CONFIG_HAVE_GENERIC_HARDIRQS=y -CONFIG_HAVE_IRQ_WORK=y -CONFIG_HAVE_KERNEL_GZIP=y -CONFIG_HAVE_KERNEL_LZMA=y -CONFIG_HAVE_KERNEL_LZO=y -CONFIG_HAVE_KERNEL_XZ=y -CONFIG_HAVE_LATENCYTOP_SUPPORT=y -CONFIG_HAVE_MEMBLOCK=y -CONFIG_HAVE_OPROFILE=y -CONFIG_HAVE_PERF_EVENTS=y -CONFIG_HAVE_PROC_CPU=y -CONFIG_HAVE_REGS_AND_STACK_ACCESS_API=y -CONFIG_HAVE_SPARSE_IRQ=y -CONFIG_HW_CONSOLE=y -CONFIG_I2C=y -CONFIG_I2C_ALGOBIT=y -CONFIG_I2C_BOARDINFO=y -CONFIG_I2C_CHARDEV=y -CONFIG_IKCONFIG=y -CONFIG_IKCONFIG_PROC=y -CONFIG_INPUT=y -# CONFIG_INPUT_MISC is not set -CONFIG_INPUT_TOUCHSCREEN=y -CONFIG_IRQ_DOMAIN=y -CONFIG_KTIME_SCALAR=y -CONFIG_LOGO=y -CONFIG_LOGO_LINUX_CLUT224=y -CONFIG_LOGO_LINUX_MONO=y -CONFIG_LOGO_LINUX_VGA16=y -CONFIG_LOG_BUF_SHIFT=16 -# CONFIG_MACH_EDB9302A is not set -# CONFIG_MACH_EDB9307A is not set -# CONFIG_MACH_EDB9315A is not set -CONFIG_MACH_SIM_ONE=y -# CONFIG_MACH_SNAPPER_CL15 is not set -# CONFIG_MACH_VISION_EP9307 is not set -# CONFIG_MFD_T7L66XB is not set -CONFIG_MMC=y -CONFIG_MMC_BLOCK=y -CONFIG_MMC_SPI=y -CONFIG_MODULE_FORCE_UNLOAD=y -CONFIG_MTD_CFI_ADV_OPTIONS=y -# CONFIG_MTD_CFI_GEOMETRY is not set -CONFIG_MTD_CFI_STAA=y -# CONFIG_MTD_COMPLEX_MAPPINGS is not set -CONFIG_MTD_PHYSMAP=y -CONFIG_MTD_RAM=y -CONFIG_MULTI_IRQ_HANDLER=y -CONFIG_NEED_DMA_MAP_STATE=y -CONFIG_NEED_MACH_MEMORY_H=y -CONFIG_NEED_PER_CPU_KM=y -CONFIG_PAGEFLAGS_EXTENDED=y -CONFIG_PAGE_OFFSET=0xC0000000 -# CONFIG_PCI_SYSCALL is not set -CONFIG_PERF_USE_VMALLOC=y -# CONFIG_PREEMPT_RCU is not set -# CONFIG_SCSI_DMA is not set -# CONFIG_SERIAL_8250 is not set -CONFIG_SERIAL_AMBA_PL010=y -CONFIG_SERIAL_AMBA_PL010_CONSOLE=y -# CONFIG_SERIAL_AMBA_PL011 is not set -CONFIG_SPI=y -CONFIG_SPI_BITBANG=y -CONFIG_SPI_EP93XX=y -CONFIG_SPI_MASTER=y -CONFIG_SPLIT_PTLOCK_CPUS=999999 -CONFIG_SYS_SUPPORTS_APM_EMULATION=y -# CONFIG_TCP_CONG_ADVANCED is not set -# CONFIG_TOUCHSCREEN_ATMEL_MXT is not set -# CONFIG_TOUCHSCREEN_AUO_PIXCIR is not set -# CONFIG_TOUCHSCREEN_BU21013 is not set -# CONFIG_TOUCHSCREEN_DYNAPRO is not set -# CONFIG_TOUCHSCREEN_EGALAX is not set -# CONFIG_TOUCHSCREEN_EP93XX is not set -# CONFIG_TOUCHSCREEN_HAMPSHIRE is not set -# CONFIG_TOUCHSCREEN_MAX11801 is not set -# CONFIG_TOUCHSCREEN_PIXCIR is not set -# CONFIG_TOUCHSCREEN_ST1232 is not set -# CONFIG_TOUCHSCREEN_TSC2005 is not set -# CONFIG_TOUCHSCREEN_TSC_SERIO is not set -CONFIG_UID16=y -# CONFIG_USB_ARCH_HAS_EHCI is not set -# CONFIG_USB_ARCH_HAS_XHCI is not set -CONFIG_USB_SUPPORT=y -CONFIG_VECTORS_BASE=0xffff0000 -CONFIG_VIDEO_OUTPUT_CONTROL=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_VT=y -CONFIG_VT_CONSOLE=y -# CONFIG_VT_HW_CONSOLE_BINDING is not set -CONFIG_XZ_DEC_ARM=y -CONFIG_XZ_DEC_BCJ=y -CONFIG_ZBOOT_ROM_BSS=0x0 -CONFIG_ZBOOT_ROM_TEXT=0x0 -CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/ep93xx/patches-3.3/001-ep93xx_cpuinfo.patch b/target/linux/ep93xx/patches-3.3/001-ep93xx_cpuinfo.patch deleted file mode 100644 index 224d188b36..0000000000 --- a/target/linux/ep93xx/patches-3.3/001-ep93xx_cpuinfo.patch +++ /dev/null @@ -1,59 +0,0 @@ -This patch puts the EP93xx chip revision and unique ID into /proc/cpuinfo. -This is necessary to be able to set a unique MAC address for DHCP purposes -by adding a line to /etc/network/interfaces: - -# Generate a unique locally-assigned MAC address from the CPU serial number -pre-up ifconfig eth0 hw ether `sed -n 's/^Serial.* 000000/02/p' /proc/cpuinfo` - -It uses the chip revision reading code in the ep93xx-chip-revision patch. - -Really, this is wrong, since /proc/cpuinfo should report the revision and -serial number of the ARM920T processor, while these are the rev and serial -of the EP93xx SoC. In a future kernel (>2.6.34) there may be a new file -/proc/socinfo for this information. - - -martinwguy 14 May 2010 - ---- a/arch/arm/kernel/setup.c -+++ b/arch/arm/kernel/setup.c -@@ -54,6 +54,12 @@ - #include - #include - -+#if defined(CONFIG_ARCH_EP93XX) -+#include -+#include -+#include -+#endif -+ - #if defined(CONFIG_DEPRECATED_PARAM_STRUCT) - #include "compat.h" - #endif -@@ -1087,9 +1093,16 @@ static int c_show(struct seq_file *m, vo - seq_puts(m, "\n"); - - seq_printf(m, "Hardware\t: %s\n", machine_name); -+#if defined(CONFIG_ARCH_EP93XX) -+ seq_printf(m, "Revision\t: %04x\n", -+ ep93xx_chip_revision()); -+ seq_printf(m, "Serial\t\t: %016x\n", -+ *((unsigned int *)EP93XX_SECURITY_UNIQID)); -+#else - seq_printf(m, "Revision\t: %04x\n", system_rev); - seq_printf(m, "Serial\t\t: %08x%08x\n", - system_serial_high, system_serial_low); -+#endif - - return 0; - } ---- a/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h -+++ b/arch/arm/mach-ep93xx/include/mach/ep93xx-regs.h -@@ -97,6 +97,8 @@ - #define EP93XX_I2S_BASE EP93XX_APB_IOMEM(0x00020000) - - #define EP93XX_SECURITY_BASE EP93XX_APB_IOMEM(0x00030000) -+#define EP93XX_SECURITY_REG(x) (EP93XX_SECURITY_BASE + (x)) -+#define EP93XX_SECURITY_UNIQID EP93XX_SECURITY_REG(0x2440) - - #define EP93XX_GPIO_PHYS_BASE EP93XX_APB_PHYS(0x00040000) - #define EP93XX_GPIO_BASE EP93XX_APB_IOMEM(0x00040000) diff --git a/target/linux/ep93xx/patches-3.3/003-ep93xx_touchscreen.patch b/target/linux/ep93xx/patches-3.3/003-ep93xx_touchscreen.patch deleted file mode 100644 index f37836d998..0000000000 --- a/target/linux/ep93xx/patches-3.3/003-ep93xx_touchscreen.patch +++ /dev/null @@ -1,1061 +0,0 @@ ---- - arch/arm/mach-ep93xx/include/mach/hardware.h | 1 - arch/arm/mach-ep93xx/include/mach/regs_touch.h | 95 ++ - drivers/input/touchscreen/Kconfig | 5 - drivers/input/touchscreen/Makefile | 1 - drivers/input/touchscreen/ep93xx_ts.c | 1117 +++++++++++++++++++++++++ - drivers/input/touchscreen/ep93xx_ts.h | 53 + - 6 files changed, 1272 insertions(+) - ---- a/drivers/input/touchscreen/Kconfig -+++ b/drivers/input/touchscreen/Kconfig -@@ -200,6 +200,15 @@ config TOUCHSCREEN_EGALAX - To compile this driver as a module, choose M here: the - module will be called egalax_ts. - -+config TOUCHSCREEN_EP93XX -+ tristate "EP93xx Touchscreen" -+ depends on ARM && INPUT && ARCH_EP93XX -+ help -+ Say Y here to enable support for EP93xx touch screen. -+ -+ To compile this driver as a module, choose M here: -+ the module will be called ep93xx_ts. -+ - config TOUCHSCREEN_FUJITSU - tristate "Fujitsu serial touchscreen" - select SERIO ---- a/drivers/input/touchscreen/Makefile -+++ b/drivers/input/touchscreen/Makefile -@@ -25,6 +25,7 @@ obj-$(CONFIG_TOUCHSCREEN_GUNZE) += gunz - obj-$(CONFIG_TOUCHSCREEN_EETI) += eeti_ts.o - obj-$(CONFIG_TOUCHSCREEN_ELO) += elo.o - obj-$(CONFIG_TOUCHSCREEN_EGALAX) += egalax_ts.o -+obj-$(CONFIG_TOUCHSCREEN_EP93XX) += ep93xx_ts.o - obj-$(CONFIG_TOUCHSCREEN_FUJITSU) += fujitsu_ts.o - obj-$(CONFIG_TOUCHSCREEN_INEXIO) += inexio.o - obj-$(CONFIG_TOUCHSCREEN_INTEL_MID) += intel-mid-touch.o ---- /dev/null -+++ b/drivers/input/touchscreen/ep93xx_ts.c -@@ -0,0 +1,1021 @@ -+/* -+ * linux/drivers/input/touchscreen/ep93xx_ts.c -+ * -+ * Copyright (C) 2003-2004 Cirrus Corp. -+ * -+ * This program is free software; you can redistribute it and/or modify -+ * it under the terms of the GNU General Public License version 2 as -+ * published by the Free Software Foundation. -+ */ -+ -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+#include -+ -+/* This stuff should be in ep93xx-regs.h */ -+#define EP93XX_TOUCHSCREEN_REG(x) (EP93XX_TOUCHSCREEN_BASE + (x)) -+/* R/W touchscreen controller setup control register. */ -+#define EP93XX_TOUCHSCREEN_SETUP EP93XX_TOUCHSCREEN_REG(0x00) -+/* R/W touchscreen controller max/min register. */ -+#define EP93XX_TOUCHSCREEN_XYMAXMIN EP93XX_TOUCHSCREEN_REG(0x04) -+/* R touchscreen controller result register. */ -+#define EP93XX_TOUCHSCREEN_XYRESULT EP93XX_TOUCHSCREEN_REG(0x08) -+/* LOCKED R/W touchscreen Switch Matrix control register. */ -+#define EP93XX_TOUCHSCREEN_DISCHARGE EP93XX_TOUCHSCREEN_REG(0x0C) -+#define EP93XX_TOUCHSCREEN_XSAMPLE EP93XX_TOUCHSCREEN_REG(0x10) -+#define EP93XX_TOUCHSCREEN_YSAMPLE EP93XX_TOUCHSCREEN_REG(0x14) -+#define EP93XX_TOUCHSCREEN_DIRECT EP93XX_TOUCHSCREEN_REG(0x18) -+#define EP93XX_TOUCHSCREEN_DETECT EP93XX_TOUCHSCREEN_REG(0x1C) -+/* NA R/W touchscreen software lock register. */ -+#define EP93XX_TOUCHSCREEN_SWLOCK EP93XX_TOUCHSCREEN_REG(0x20) -+/* R/W touchscreen setup control register #2. */ -+#define EP93XX_TOUCHSCREEN_SETUP2 EP93XX_TOUCHSCREEN_REG(0x24) -+ -+/* These are duplicated in mach-ep93xx/core.c */ -+#define EP93XX_TIMER_REG(x) (EP93XX_TIMER_BASE + (x)) -+#define EP93XX_TIMER2_LOAD EP93XX_TIMER_REG(0x20) -+#define EP93XX_TIMER2_VALUE EP93XX_TIMER_REG(0x24) -+#define EP93XX_TIMER2_CONTROL EP93XX_TIMER_REG(0x28) -+#define EP93XX_TIMER2_CLEAR EP93XX_TIMER_REG(0x2c) -+ -+/* -+ * Register bit definitions -+ */ -+#define TSSETUP_SDLY_MASK 0x000003FF -+#define TSSETUP_SDLY_SHIFT 0 -+#define TSSETUP_NSMP_4 0x00000000 -+#define TSSETUP_NSMP_8 0x00000400 -+#define TSSETUP_NSMP_16 0x00000800 -+#define TSSETUP_NSMP_32 0x00000C00 -+#define TSSETUP_NSMP_MASK 0x00000C00 -+#define TSSETUP_DEV_4 0x00000000 -+#define TSSETUP_DEV_8 0x00001000 -+#define TSSETUP_DEV_12 0x00002000 -+#define TSSETUP_DEV_16 0x00003000 -+#define TSSETUP_DEV_24 0x00004000 -+#define TSSETUP_DEV_32 0x00005000 -+#define TSSETUP_DEV_64 0x00006000 -+#define TSSETUP_DEV_128 0x00007000 -+#define TSSETUP_ENABLE 0x00008000 -+#define TSSETUP_DLY_MASK 0x03FF0000 -+#define TSSETUP_DLY_SHIFT 16 -+#define TSSETUP_TDTCT 0x80000000 -+ -+#define TSMAXMIN_XMIN_MASK 0x000000FF -+#define TSMAXMIN_XMIN_SHIFT 0 -+#define TSMAXMIN_YMIN_MASK 0x0000FF00 -+#define TSMAXMIN_YMIN_SHIFT 8 -+#define TSMAXMIN_XMAX_MASK 0x00FF0000 -+#define TSMAXMIN_XMAX_SHIFT 16 -+#define TSMAXMIN_YMAX_MASK 0xFF000000 -+#define TSMAXMIN_YMAX_SHIFT 24 -+ -+#define TSXYRESULT_X_MASK 0x00000FFF -+#define TSXYRESULT_X_SHIFT 0 -+#define TSXYRESULT_AD_MASK 0x0000FFFF -+#define TSXYRESULT_AD_SHIFT 0 -+#define TSXYRESULT_Y_MASK 0x0FFF0000 -+#define TSXYRESULT_Y_SHIFT 16 -+#define TSXYRESULT_SDR 0x80000000 -+ -+#define TSX_SAMPLE_MASK 0x00003FFF -+#define TSX_SAMPLE_SHIFT 0x00 -+#define TSY_SAMPLE_MASK 0x3FFF0000 -+#define TSY_SAMPLE_SHIFT 0x10 -+ -+#define TSSETUP2_TINT 0x00000001 -+#define TSSETUP2_NICOR 0x00000002 -+#define TSSETUP2_PINT 0x00000004 -+#define TSSETUP2_PENSTS 0x00000008 -+#define TSSETUP2_PINTEN 0x00000010 -+#define TSSETUP2_DEVINT 0x00000020 -+#define TSSETUP2_DINTEN 0x00000040 -+#define TSSETUP2_DTMEN 0x00000080 -+#define TSSETUP2_DISDEV 0x00000100 -+#define TSSETUP2_NSIGND 0x00000200 -+#define TSSETUP2_S28EN 0x00000400 -+#define TSSETUP2_RINTEN 0x00000800 -+ -+#define TSXYRESULT_SDR 0x80000000 -+ -+/* -+ * These are used as trigger levels to know when we have pen up/down. -+ * The rules: -+ * 1. TS_HEAVY_INV_PRESSURE < TS_LIGHT_INV_PRESSURE because these -+ * are Inverse pressure. -+ * 2. Any touch lighter than TS_LIGHT_INV_PRESSURE is a pen up. -+ * 3. Any touch heavier than TS_HEAVY_INV_PRESSURE is a pen down. -+ */ -+#define TS_HEAVY_INV_PRESSURE 0xFE0 /* C00 */ -+#define TS_LIGHT_INV_PRESSURE 0xFFF /* e00 */ -+ -+/* -+ * If the x, y, or inverse pressure changes more than these values -+ * between two succeeding points, the point is not reported. -+ */ -+#define TS_MAX_VALID_XY_CHANGE 0x300 -+#define TS_MAX_VALID_PRESSURE_CHANGE 0x100 -+ -+/* -+ * This is the minimum Z1 Value that is valid. -+ */ -+#define MIN_Z1_VALUE 0x50 -+ -+/* -+ * Settling delay for taking each ADC measurement. Increase this -+ * if ts is jittery. -+ */ -+#define EP93XX_TS_ADC_DELAY_USEC 2000 -+ -+/* -+ * Delay between TS points. -+ */ -+#define EP93XX_TS_PER_POINT_DELAY_USEC 10000 -+ -+/* -+ * A few more macros... -+ */ -+#define TSSETUP_DEFAULT (TSSETUP_NSMP_32 | TSSETUP_DEV_64 | \ -+ ((128<= TS_LIGHT_INV_PRESSURE) -+ { -+ bCurrentPenDown = 0; -+ ee93xx_ts_evt_add(0, guiLastX, guiLastY, 0); -+ TS_Hardware_Scan_Mode(); -+ return; -+ } -+ -+ /* -+ * Hysteresis: -+ * If the pen pressure is hard enough to be less than the 'min' OR -+ * the pen is already down and is still less than the 'max'... -+ */ -+ if ((uiInvPressure < TS_HEAVY_INV_PRESSURE) || -+ (bCurrentPenDown && (uiInvPressure < TS_LIGHT_INV_PRESSURE))) -+ { -+ if (bCurrentPenDown) -+ { -+ /* -+ * If pen was previously down, check the difference between -+ * the last sample and this one... if the difference between -+ * samples is too great, ignore the sample. -+ */ -+ uiXDiff = abs(guiLastX - sTouch.uiX); -+ uiYDiff = abs(guiLastY - sTouch.uiY); -+ uiInvPressureDiff = abs(guiLastInvPressure - uiInvPressure); -+ -+ if (uiXDiff < TS_MAX_VALID_XY_CHANGE -+ && uiYDiff < TS_MAX_VALID_XY_CHANGE -+ && uiInvPressureDiff < TS_MAX_VALID_PRESSURE_CHANGE) -+ { -+ bValidPoint = 1; -+ } -+ } -+ else -+ { -+ bValidPoint = 1; -+ } -+ -+ /* -+ * If either the pen was put down or dragged make a note of it. -+ */ -+ if (bValidPoint) -+ { -+ guiLastX = sTouch.uiX; -+ guiLastY = sTouch.uiY; -+ guiLastInvPressure = uiInvPressure; -+ bCurrentPenDown = 1; -+ ee93xx_ts_evt_add(1, sTouch.uiX, sTouch.uiY, -+ 0x7000000 / uiInvPressure); -+ } -+ -+ TS_Soft_Scan_Mode(); -+ return; -+ } -+ -+ TS_Hardware_Scan_Mode(); -+} -+ -+static void ep93xx_ts_set_direct(unsigned int uiADCSwitch) -+{ -+ unsigned int uiResult; -+ -+ /* -+ * Set the switch settings in the direct register. -+ */ -+ __raw_writel(0xaa, EP93XX_TOUCHSCREEN_SWLOCK); -+ __raw_writel(uiADCSwitch, EP93XX_TOUCHSCREEN_DIRECT); -+ -+ /* -+ * Read and throw away the first sample. -+ */ -+ do { -+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT); -+ } while (!(uiResult & TSXYRESULT_SDR)); -+ -+} -+ -+static unsigned int ADCGetData(unsigned int uiSamples, unsigned int uiMaxDiff) -+{ -+ unsigned int uiResult, uiValue, uiCount, uiLowest, uiHighest, uiSum, uiAve; -+ -+ do -+ { -+ /* -+ * Initialize our values. -+ */ -+ uiLowest = 0xfffffff; -+ uiHighest = 0; -+ uiSum = 0; -+ -+ for (uiCount = 0; uiCount < uiSamples; uiCount++) -+ { -+ /* -+ * Read the touch screen four more times and average. -+ */ -+ do { -+ uiResult = __raw_readl(EP93XX_TOUCHSCREEN_XYRESULT); -+ } while (!(uiResult & TSXYRESULT_SDR)); -+ -+ uiValue = (uiResult & TSXYRESULT_AD_MASK) >> TSXYRESULT_AD_SHIFT; -+ uiValue = ((uiValue >> 4) + ((1 + TSXYRESULT_X_MASK)>>1)) & TSXYRESULT_X_MASK; -+ -+ /* -+ * Add up the values. -+ */ -+ uiSum += uiValue; -+ -+ /* -+ * Get the lowest and highest values. -+ */ -+ if (uiValue < uiLowest) -+ { -+ uiLowest = uiValue; -+ } -+ if (uiValue > uiHighest) -+ { -+ uiHighest = uiValue; -+ } -+ } -+ } while ((uiHighest - uiLowest) > uiMaxDiff); -+ -+ /* -+ * Calculate the Average value. -+ */ -+ uiAve = uiSum / uiSamples; -+ -+ return uiAve; -+} -+ -+/* -+ * CalculateInvPressure -+ * -+ * Is the Touch Valid. Touch is not valid if the X or Y value is not -+ * in range and the pressure is not enough. -+ * -+ * Touch resistance can be measured by the following formula: -+ * -+ * Rx * X * Z2 -+ * Rtouch = --------- * (-- - 1) -+ * 4096 Z1 -+ * -+ * This is simplified in the ration of Rtouch to Rx. The lower the value, the -+ * higher the pressure. -+ * -+ * Z2 -+ * InvPressure = X * (-- - 1) -+ * Z1 -+ */ -+static unsigned int CalculateInvPressure(void) -+{ -+ unsigned int uiInvPressure; -+ -+ /* -+ * Check to see if the point is valid. -+ */ -+ if (sTouch.uiZ1 < MIN_Z1_VALUE) -+ { -+ uiInvPressure = 0x10000; -+ } -+ -+ /* -+ * Can omit the pressure calculation if you need to get rid of the division. -+ */ -+ else -+ { -+ uiInvPressure = ((sTouch.uiX * sTouch.uiZ2) / sTouch.uiZ1) - sTouch.uiX; -+ } -+ -+ return uiInvPressure; -+} -+ -+/* -+ * TS_Hardware_Scan_Mode -+ * -+ * Enables the ep93xx ts scanning engine so that when the pen goes down -+ * we will get an interrupt. -+ */ -+static void TS_Hardware_Scan_Mode(void) -+{ -+ unsigned int uiDevCfg; -+ -+ /* -+ * Disable the soft scanning engine. -+ */ -+ sTouch.state = TS_STATE_STOPPED; -+ Stop_Timer2(); -+ -+ /* -+ * Clear the TIN (Touchscreen INactive) bit so we can go to -+ * automatic scanning mode. -+ */ -+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG); -+ ep93xx_syscon_swlocked_write(uiDevCfg & ~EP93XX_SYSCON_DEVCFG_TIN, -+ EP93XX_SYSCON_DEVCFG); -+ -+ /* -+ * Enable the touch screen scanning state machine by setting -+ * the ENABLE bit. -+ */ -+ __raw_writel(TSSETUP_DEFAULT | TSSETUP_ENABLE, EP93XX_TOUCHSCREEN_SETUP); -+ -+ /* -+ * Set the flag to show that we are in interrupt mode. -+ */ -+ gScanningMode = TS_MODE_HARDWARE_SCAN; -+ -+ /* -+ * Initialize EP93XX_TOUCHSCREEN_SETUP2 register. -+ */ -+ __raw_writel(TSSETUP2_DEFAULT, EP93XX_TOUCHSCREEN_SETUP2); -+ -+} -+ -+/* -+ * TS_Soft_Scan_Mode -+ * -+ * Sets the touch screen to manual polling mode. -+ */ -+static void TS_Soft_Scan_Mode(void) -+{ -+ unsigned int uiDevCfg; -+ -+ if (gScanningMode != TS_MODE_SOFT_SCAN) -+ { -+ /* -+ * Disable the touch screen scanning state machine by clearing -+ * the ENABLE bit. -+ */ -+ __raw_writel(TSSETUP_DEFAULT, EP93XX_TOUCHSCREEN_SETUP); -+ -+ /* -+ * Set the TIN bit so we can do manual touchscreen polling. -+ */ -+ uiDevCfg = __raw_readl(EP93XX_SYSCON_DEVCFG); -+ ep93xx_syscon_swlocked_write(uiDevCfg | EP93XX_SYSCON_DEVCFG_TIN, -+ EP93XX_SYSCON_DEVCFG); -+ } -+ -+ /* -+ * Set the switch register up for the first ADC reading -+ */ -+ ep93xx_ts_set_direct(sSwitchSettings.uiSwitchZ1); -+ -+ /* -+ * Initialize our software state machine to know which ADC -+ * reading to take -+ */ -+ sTouch.state = TS_STATE_Z1; -+ -+ /* -+ * Set the timer so after a mSec or two settling delay it will -+ * take the first ADC reading. -+ */ -+ Set_Timer2_uSec(EP93XX_TS_PER_POINT_DELAY_USEC); -+ -+ /* -+ * Note that we are in sw scanning mode not hw scanning mode. -+ */ -+ gScanningMode = TS_MODE_SOFT_SCAN; -+ -+} -+ -+static void Set_Timer2_uSec(unsigned int uiDelay_uSec) -+{ -+ unsigned int uiClockTicks; -+ -+ /* -+ * Stop timer 2 -+ */ -+ __raw_writel(0, EP93XX_TIMER2_CONTROL); -+ -+ uiClockTicks = ((uiDelay_uSec * 508) + 999) / 1000; -+ __raw_writel(uiClockTicks, EP93XX_TIMER2_LOAD); -+ __raw_writel(uiClockTicks, EP93XX_TIMER2_VALUE); -+ -+ /* -+ * Set up Timer 2 for 508 kHz clock and periodic mode. -+ */ -+ __raw_writel(0xC8, EP93XX_TIMER2_CONTROL); -+ -+} -+ -+static void Stop_Timer2(void) -+{ -+ __raw_writel(0, EP93XX_TIMER2_CONTROL); -+} -+ -+/* -+ * Initialization and exit routines -+ */ -+int __init ep93xx_ts_init(void) -+{ -+ int retval; -+ -+ retval = request_irq(IRQ_EP93XX_TOUCH, ep93xx_ts_isr, -+ IRQF_DISABLED, "ep93xx_ts", 0); -+ if (retval) -+ { -+ printk(KERN_WARNING "ep93xx_ts: failed to get touchscreen IRQ\n"); -+ return retval; -+ } -+ -+ retval = request_irq(IRQ_EP93XX_TIMER2, ep93xx_timer2_isr, -+ IRQF_DISABLED, "ep93xx_timer2", 0); -+ if (retval) -+ { -+ printk(KERN_WARNING "ep93xx_ts: failed to get timer2 IRQ\n"); -+ free_irq(IRQ_EP93XX_TOUCH, 0); -+ return retval; -+ } -+ -+ misc_register(&ep93xx_ts_miscdev); -+ -+ sTouch.state = TS_STATE_STOPPED; -+ gScanningMode = TS_MODE_UN_INITIALIZED; -+ -+ printk(KERN_NOTICE "ep93xx touchscreen driver configured for 4-wire operation\n"); -+ -+ return 0; -+} -+ -+void __exit ep93xx_ts_exit(void) -+{ -+ Stop_Timer2(); -+ -+ free_irq(IRQ_EP93XX_TOUCH, 0); -+ free_irq(IRQ_EP93XX_TIMER2, 0); -+ -+ misc_deregister(&ep93xx_ts_miscdev); -+} -+ -+module_init(ep93xx_ts_init); -+module_exit(ep93xx_ts_exit); -+ -+MODULE_DESCRIPTION("Cirrus EP93xx touchscreen driver"); -+MODULE_SUPPORTED_DEVICE("touchscreen/ep93xx"); -+MODULE_LICENSE("GPL"); diff --git a/target/linux/ep93xx/patches-3.3/004-simone_add_mmc_spi.patch b/target/linux/ep93xx/patches-3.3/004-simone_add_mmc_spi.patch deleted file mode 100644 index d8160f56c0..0000000000 --- a/target/linux/ep93xx/patches-3.3/004-simone_add_mmc_spi.patch +++ /dev/null @@ -1,180 +0,0 @@ -This enables the mmc-over-spi driver for the Sim.One board, based on Mika's -patch, which used a GPIO for chip select in stead of the default SFRMOUT pin. -I've modified it to use the usual SFRMOUT; if you've modified your Sim.One -board to use a GPIO instead, uncomment and modify -// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15 -in the source file. - -martinwguy, 14 May 2010 - -From: Mika Westerberg -Date: Wed, 28 Apr 2010 08:42:46 +0300 -Subject: [PATCH] ep93xx: simone: added board specific SPI support for MMC/SD cards - -This includes setting up EGPIOs 0 and 9 for card detection and chip select -respectively. - ---- a/arch/arm/mach-ep93xx/simone.c -+++ b/arch/arm/mach-ep93xx/simone.c -@@ -18,12 +18,17 @@ - #include - #include - #include -+#include - #include - #include -+#include -+#include -+#include - - #include - #include - #include -+#include - - #include - #include -@@ -39,6 +44,135 @@ static struct ep93xxfb_mach_info __initd - .flags = EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING, - }; - -+/* -+ * GPIO lines used for MMC card detection. -+ */ -+#define MMC_CARD_DETECT_GPIO EP93XX_GPIO_LINE_EGPIO0 -+ -+/* -+ * If you have hacked your Sim.One to use a GPIO as SD card chip select -+ * (SD pin 1), uncomment the following line. -+ * The example, EGPIO15, is on TP17 near the CPU. -+ */ -+// #define MMC_CHIP_SELECT_GPIO EP93XX_GPIO_LINE_EGPIO15 -+ -+/* -+ * MMC SPI chip select GPIO handling. If you are using SFRMOUT (SFRM1) signal, -+ * you can leave these empty and pass NULL as .controller_data. -+ */ -+ -+#ifdef MMC_CHIP_SELECT_GPIO -+static int simone_mmc_spi_setup(struct spi_device *spi) -+{ -+ unsigned int gpio = MMC_CHIP_SELECT_GPIO; -+ int err; -+ -+ err = gpio_request(gpio, spi->modalias); -+ if (err) -+ return err; -+ -+ err = gpio_direction_output(gpio, 1); -+ if (err) { -+ gpio_free(gpio); -+ return err; -+ } -+ -+ return 0; -+} -+ -+static void simone_mmc_spi_cleanup(struct spi_device *spi) -+{ -+ unsigned int gpio = MMC_CHIP_SELECT_GPIO; -+ -+ gpio_set_value(gpio, 1); -+ gpio_direction_input(gpio); -+ gpio_free(gpio); -+} -+ -+static void simone_mmc_spi_cs_control(struct spi_device *spi, int value) -+{ -+ gpio_set_value(MMC_CHIP_SELECT_GPIO, value); -+} -+ -+static struct ep93xx_spi_chip_ops simone_mmc_spi_ops = { -+ .setup = simone_mmc_spi_setup, -+ .cleanup = simone_mmc_spi_cleanup, -+ .cs_control = simone_mmc_spi_cs_control, -+}; -+#endif -+ -+/* -+ * MMC card detection GPIO setup. -+ */ -+static int simone_mmc_spi_init(struct device *dev, -+ irqreturn_t (*irq_handler)(int, void *), void *mmc) -+{ -+ unsigned int gpio = MMC_CARD_DETECT_GPIO; -+ int irq, err; -+ -+ err = gpio_request(gpio, dev_name(dev)); -+ if (err) -+ return err; -+ -+ err = gpio_direction_input(gpio); -+ if (err) -+ goto fail; -+ -+ irq = gpio_to_irq(gpio); -+ if (irq < 0) -+ goto fail; -+ -+ err = request_irq(irq, irq_handler, IRQF_TRIGGER_FALLING, -+ "MMC card detect", mmc); -+ if (err) -+ goto fail; -+ -+ printk(KERN_INFO "%s: using irq %d for MMC card detection\n", -+ dev_name(dev), irq); -+ -+ return 0; -+fail: -+ gpio_free(gpio); -+ return err; -+} -+ -+static void simone_mmc_spi_exit(struct device *dev, void *mmc) -+{ -+ unsigned int gpio = MMC_CARD_DETECT_GPIO; -+ -+ free_irq(gpio_to_irq(gpio), mmc); -+ gpio_free(gpio); -+} -+ -+static struct mmc_spi_platform_data simone_mmc_spi_data = { -+ .init = simone_mmc_spi_init, -+ .exit = simone_mmc_spi_exit, -+ .detect_delay = 500, -+ .ocr_mask = MMC_VDD_32_33 | MMC_VDD_33_34, -+}; -+ -+static struct spi_board_info simone_spi_devices[] __initdata = { -+ { -+ .modalias = "mmc_spi", -+#ifdef MMC_CHIP_SELECT_GPIO -+ .controller_data = &simone_mmc_spi_ops, -+#endif -+ .platform_data = &simone_mmc_spi_data, -+ /* -+ * We use 10 MHz even though the maximum is 3.7 MHz. The driver -+ * will limit it automatically to max. frequency. -+ */ -+ .max_speed_hz = 10 * 1000 * 1000, -+ .bus_num = 0, -+ .chip_select = 0, -+ .mode = SPI_MODE_3, -+ }, -+}; -+ -+static struct ep93xx_spi_info simone_spi_info __initdata = { -+ .num_chipselect = ARRAY_SIZE(simone_spi_devices), -+}; -+ - static struct i2c_gpio_platform_data __initdata simone_i2c_gpio_data = { - .sda_pin = EP93XX_GPIO_LINE_EEDAT, - .sda_is_open_drain = 0, -@@ -73,6 +207,8 @@ static void __init simone_init_machine(v - ep93xx_register_fb(&simone_fb_info); - ep93xx_register_i2c(&simone_i2c_gpio_data, simone_i2c_board_info, - ARRAY_SIZE(simone_i2c_board_info)); -+ ep93xx_register_spi(&simone_spi_info, simone_spi_devices, -+ ARRAY_SIZE(simone_spi_devices)); - simone_register_audio(); - } -