From: David Bauer Date: Sat, 8 Feb 2020 11:58:25 +0000 (+0100) Subject: ath79: add support for Siemens WS-AP3610 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=d2b8ccb1c04d;p=openwrt%2Fstaging%2Fstintel.git ath79: add support for Siemens WS-AP3610 Hardware -------- SoC: Atheros AR7161 RAM: Samsung K4H511638D-UCCC 2x 64M DDR1 SPI: Micron M25P128 (16M) WiFi: Atheros AR9160 bgn Atheros AR9160 an ETH: Broadcom BCM5481 LED: Power (Green/Red) ETH (Green / Blue / Yellow) (PHY-controlled) WiFi 5 (Green / Blue) WiFi 2 (Green / Blue) BTN: Reset Serial: Cisco-Style RJ45 - 115200 8N1 Installation ------------ 1. Download the OpenWrt initramfs-image. Place it into a TFTP server root directory and rename it to 1401A8C0.img. Configure the TFTP server to listen at 192.168.1.66/24. 2. Connect the TFTP server to the access point. 3. Connect to the serial console of the access point. Attach power and interrupt the boot procedure when prompted (bootdelay is 1 second). 4. Configure the U-Boot environment for booting OpenWrt from Ram and flash: $ setenv boot_openwrt 'setenv bootargs; bootm 0xbf080000' $ setenv ramboot_openwrt 'setenv serverip 192.168.1.66; tftpboot; bootm' $ saveenv 5. Load OpenWrt into memory: $ run ramboot_openwrt Wait for the image to boot. 6. Transfer the OpenWrt sysupgrade image to the device. Write the image to flash using sysupgrade: $ sysupgrade -n /path/to/openwrt-sysuograde.bin Signed-off-by: David Bauer --- diff --git a/target/linux/ath79/dts/ar7161_siemens_ws-ap3610.dts b/target/linux/ath79/dts/ar7161_siemens_ws-ap3610.dts new file mode 100644 index 0000000000..8e0a80cb32 --- /dev/null +++ b/target/linux/ath79/dts/ar7161_siemens_ws-ap3610.dts @@ -0,0 +1,186 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar7100.dtsi" + +/ { + compatible = "siemens,ws-ap3610", "qca,ar7161"; + model = "Siemens WS-AP3610"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_red; + led-running = &led_power_green; + led-upgrade = &led_power_red; + label-mac-device = ð0; + }; + + extosc: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-output-names = "ref"; + clock-frequency = <40000000>; + }; + + leds { + compatible = "gpio-leds"; + + led_power_green: led_power_green { + label = "ws-ap3610:green:power"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + + led_power_red: led_power_red { + label = "ws-ap3610:red:power"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + led_wlan5_blue { + label = "ws-ap3610:blue:wlan5"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led_wlan5_green { + label = "ws-ap3610:green:wlan5"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + led_wlan2_blue { + label = "ws-ap3610:blue:wlan2"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + led_wlan2_green { + label = "ws-ap3610:green:wlan2"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + /* + * When the compatible-is missing, PHY autodetection + * is performed, but the PHY-ID reads all 0xff. + * + * Linux does not create the device in this case, + * and the reset is never even de-asserted. + */ + compatible = "ethernet-phy-id0143.bca2", + "ethernet-phy-ieee802.3-c22"; + reg = <0>; + + resets = <&rst 8>; + reset-names = "phy"; + reset-assert-us = <10000>; + reset-deassert-us = <10000>; + }; +}; + +ð0 { + status = "okay"; + + phy-mode = "rgmii-id"; + phy-handle = <&phy0>; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "u-boot-bak"; + reg = <0x40000 0x40000>; + read-only; + }; + + partition@80000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x80000 0xe00000>; + }; + + partition@e80000 { + label = "cfg1"; + reg = <0xe80000 0x40000>; + read-only; + }; + + partition@ec0000 { + label = "cfg2"; + reg = <0xec0000 0x40000>; + read-only; + }; + + partition@f00000 { + label = "nvram1"; + reg = <0xf00000 0x40000>; + read-only; + }; + + partition@f40000 { + label = "nvram2"; + reg = <0xf40000 0x40000>; + read-only; + }; + + partition@f80000 { + label = "rsvd1"; + reg = <0xf80000 0x40000>; + read-only; + }; + + partition@fc0000 { + label = "rsvd2"; + reg = <0xfc0000 0x40000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index a3fcf35715..69c19358e2 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -30,6 +30,7 @@ ath79_setup_interfaces() pisen,ts-d084|\ pisen,wmb001n|\ pisen,wmm003n|\ + siemens,ws-ap3610|\ tplink,cpe210-v2|\ tplink,cpe210-v3|\ tplink,cpe510-v2|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index 8c8b7932bc..f814bd46ad 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -34,6 +34,9 @@ case "$board" in [ "$PHYNBR" -eq 1 ] && \ k2t_get_mac "lan_mac" > /sys${DEVPATH}/macaddress ;; + siemens,ws-ap3610) + mtd_get_mac_ascii cfg1 RADIOADDR${PHYNBR} > /sys${DEVPATH}/macaddress + ;; trendnet,tew-823dru) # set the 2.4G interface mac address to LAN MAC [ "$PHYNBR" -eq 1 ] && \ diff --git a/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh b/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh new file mode 100644 index 0000000000..a0fb9fc717 --- /dev/null +++ b/target/linux/ath79/generic/base-files/lib/preinit/10_fix_eth_mac.sh @@ -0,0 +1,13 @@ +#!/bin/sh + +. /lib/functions.sh + +preinit_set_mac_address() { + case $(board_name) in + siemens,ws-ap3610) + ip link set dev eth0 address $(mtd_get_mac_ascii cfg1 ethaddr) + ;; + esac +} + +boot_hook_add preinit_main preinit_set_mac_address diff --git a/target/linux/ath79/generic/config-default b/target/linux/ath79/generic/config-default index 2d8f7f20c2..6cd1518e3a 100644 --- a/target/linux/ath79/generic/config-default +++ b/target/linux/ath79/generic/config-default @@ -1,4 +1,5 @@ CONFIG_AT803X_PHY=y +CONFIG_BROADCOM_PHY=y CONFIG_GPIO_WATCHDOG=y CONFIG_GPIO_WATCHDOG_ARCH_INITCALL=y CONFIG_INTEL_XWAY_PHY=y diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 05d2ba6a75..d4693cea68 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1041,6 +1041,20 @@ define Device/rosinson_wr818 endef TARGET_DEVICES += rosinson_wr818 +define Device/siemens_ws-ap3610 + SOC := ar7161 + DEVICE_VENDOR := Siemens + DEVICE_MODEL := WS-AP3610 + IMAGE_SIZE := 14336k + LOADER_TYPE := bin + LOADER_FLASH_OFFS := 0x82000 + COMPILE := loader-$(1).bin + COMPILE/loader-$(1).bin := loader-okli-compile + KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 | loader-okli $(1) 8128 | uImage none + KERNEL_INITRAMFS := kernel-bin | append-dtb | uImage none +endef +TARGET_DEVICES += siemens_ws-ap3610 + define Device/sitecom_wlr-7100 SOC := ar1022 DEVICE_VENDOR := Sitecom