From: Jean Thomas Date: Thu, 9 Nov 2023 10:28:45 +0000 (+0100) Subject: mediatek: Add support for GL.iNet X3000 (Spitz AX) and XE3000 (Puli AX) X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=d1016446dacd16a87e807478227f4f96a0a37a45;p=openwrt%2Fstaging%2Frmilecki.git mediatek: Add support for GL.iNet X3000 (Spitz AX) and XE3000 (Puli AX) The GL.iNet X3000 and XE3000 are Wi-Fi 6 5G cellular routers, based on MediaTek MT7981A SoC. The XE3000 is the same device as the X3000, except for an additional battery. Specifications: - SoC: Filogic 820 MT7981A (1.3GHz) - RAM: DDR4 512M - Flash: eMMC 8G, MicroSD card slot - WiFi: 2.4GHz and 5GHz with 6 antennas - Ethernet: - 1x LAN (10/100/1000M) - 1x WAN (10/100/1000/2500M) - 5G: Quectel RM520N-GL with two nano-SIM card slots - USB: 1x USB 2.0 port - UART: - 3.3V, TX, RX, GND / 115200 8N1 MAC addresses as verified by OEM firmware: vendor OpenWrt address source WAN eth0 label factory 0x0a (label) LAN eth1 label + 1 2g phy0-ap0 label + 2 factory 0x04 5g phy1-ap0 label + 3 Installation via U-Boot rescue: 1. Press and hold reset button while booting the device 2. Wait for the Internet led to blink 5 times 3. Release reset button 4. The rescue page is accessible via http://192.168.1.1 5. Select the OpenWrt sysupgrade image and start upgrade 6. Wait for the router to flash new firmware and reboot Revert to stock firmware: 1. Download the stock firmware from GL.iNet website 2. Use the method explained above to flash the stock firmware Switch the modem network port between PCIe and USB interfaces: 1. Connect to the AT commands (/dev/ttyUSB2) port using e.g. minicom: minicom -D /dev/ttyUSB2 2. Check the current modem mode with 'AT+QCFG="data_interface"': - 0,0 indicates that the network port uses the USB interface - 1,0 indicates that the network port uses the PCIe interface 3. Switch the active interface with: - 'AT+QCFG="data_interface",0,0' to use the USB interface - 'AT+QCFG="data_interface",1,0' to use the PCIe interface 4. Reboot Signed-off-by: Jean Thomas --- diff --git a/target/linux/mediatek/dts/mt7981a-glinet-gl-x3000-xe3000-common.dtsi b/target/linux/mediatek/dts/mt7981a-glinet-gl-x3000-xe3000-common.dtsi new file mode 100644 index 00000000000..4b311dbe21f --- /dev/null +++ b/target/linux/mediatek/dts/mt7981a-glinet-gl-x3000-xe3000-common.dtsi @@ -0,0 +1,273 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +/dts-v1/; + +#include "mt7981.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8 root=PARTLABEL=rootfs rootwait"; + }; + + aliases { + label-mac-device = &gmac0; + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; + + fan_5v: regulator-fan-5v { + compatible = "regulator-fixed"; + regulator-name = "fan"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 28 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&pio 1 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-export { + compatible = "gpio-export"; + + hub_power { + gpio-export,name = "hub_power"; + gpio-export,output = <1>; + gpios = <&pio 5 GPIO_ACTIVE_HIGH>; + }; + + 5G_power { + gpio-export,name = "5G_power"; + gpio-export,output = <1>; + gpios = <&pio 11 GPIO_ACTIVE_HIGH>; + }; + + 5G_control { + gpio-export,name = "5G_control"; + gpio-export,output = <1>; + gpios = <&pio 9 GPIO_ACTIVE_HIGH>; + }; + + 5G_reset { + gpio-export,name = "5G_reset"; + gpio-export,output = <0>; + gpios = <&pio 10 GPIO_ACTIVE_HIGH>; + }; + }; + + leds { + compatible = "gpio-leds"; + + wifi2g { + label = "green:wifi2g"; + gpios = <&pio 30 GPIO_ACTIVE_LOW>; + }; + + wifi5g { + label = "green:wifi5g"; + gpios = <&pio 38 GPIO_ACTIVE_LOW>; + }; + + 5g_led1 { + label = "green:5g:led1"; + gpios = <&pio 6 GPIO_ACTIVE_LOW>; + }; + + 5g_led2 { + label = "green:5g:led2"; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + + 5g_led3 { + label = "green:5g:led3"; + gpios = <&pio 8 GPIO_ACTIVE_LOW>; + }; + + 5g_led4 { + label = "green:5g:led4"; + gpios = <&pio 4 GPIO_ACTIVE_HIGH>; + }; + + led_power: power { + label = "green:power"; + gpios = <&pio 39 GPIO_ACTIVE_LOW>; + }; + + wan { + label = "green:wan"; + gpios = <&pio 31 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&uart0 { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&mmc0 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + bus-width = <8>; + max-frequency = <52000000>; + cap-mmc-highspeed; + vmmc-supply = <®_3p3v>; + non-removable; + status = "okay"; + + card@0 { + compatible = "mmc-card"; + reg = <0>; + + block { + compatible = "block-device"; + partitions { + block-partition-env { + partname = "u-boot-env"; + + nvmem-layout { + compatible = "u-boot,env-layout"; + }; + }; + + block-partition-factory { + partname = "factory"; + + nvmem-layout { + compatible = "fixed-layout"; + #address-cells = <1>; + #size-cells = <1>; + + eeprom_factory_0: eeprom@0 { + reg = <0x0 0x1000>; + }; + + macaddr_factory_a: macaddr@a { + compatible = "mac-base"; + reg = <0xa 0x6>; + #nvmem-cell-cells = <1>; + }; + }; + }; + }; + }; + }; +}; + +&mdio_bus { + reset-gpios = <&pio 14 GPIO_ACTIVE_LOW>; + reset-delay-us = <600>; + reset-post-delay-us = <20000>; + + phy5: ethernet-phy@5 { + reg = <5>; + compatible = "ethernet-phy-ieee802.3-c45"; + }; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + phy-handle = <&phy5>; + nvmem-cells = <&macaddr_factory_a 0>; + nvmem-cell-names = "mac-address"; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "gmii"; + phy-handle = <&int_gbe_phy>; + nvmem-cells = <&macaddr_factory_a 1>; + nvmem-cell-names = "mac-address"; + }; +}; + +&pio { + mmc0_pins_default: mmc0-pins-default { + mux { + function = "flash"; + groups = "emmc_8"; + }; + }; + mmc0_pins_uhs: mmc0-pins-uhs { + mux { + function = "flash"; + groups = "emmc_8"; + }; + }; + pcie_pins: pcie-pins { + mux { + function = "pcie"; + groups = "pcie_pereset", "pcie_clk", "pcie_wake"; + }; + }; + pwm0_pin: pwm0-pin-g0 { + mux { + function = "pwm"; + groups = "pwm0_1"; + }; + }; +}; + +&xhci { + phys = <&u2port0 PHY_TYPE_USB2>; + vbus-supply = <®_5v>; + mediatek,u3p-dis-msk = <0x01>; + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_pins>; + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pin>; +}; + +&wifi { + nvmem-cells = <&eeprom_factory_0>; + nvmem-cell-names = "eeprom"; + status = "okay"; +}; + +&fan { + pwms = <&pwm 0 40000 0>; + fan-supply = <&fan_5v>; + interrupt-parent = <&pio>; + interrupts = <29 IRQ_TYPE_EDGE_RISING>; + status = "okay"; +}; diff --git a/target/linux/mediatek/dts/mt7981a-glinet-gl-x3000.dts b/target/linux/mediatek/dts/mt7981a-glinet-gl-x3000.dts new file mode 100644 index 00000000000..bee1ecd89a9 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981a-glinet-gl-x3000.dts @@ -0,0 +1,8 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7981a-glinet-gl-x3000-xe3000-common.dtsi" + +/ { + model = "GL.iNet GL-X3000"; + compatible = "glinet,gl-x3000", "mediatek,mt7981"; +}; diff --git a/target/linux/mediatek/dts/mt7981a-glinet-gl-xe3000.dts b/target/linux/mediatek/dts/mt7981a-glinet-gl-xe3000.dts new file mode 100644 index 00000000000..e14b944bc97 --- /dev/null +++ b/target/linux/mediatek/dts/mt7981a-glinet-gl-xe3000.dts @@ -0,0 +1,23 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7981a-glinet-gl-x3000-xe3000-common.dtsi" + +/ { + model = "GL.iNet GL-XE3000"; + compatible = "glinet,gl-xe3000", "mediatek,mt7981"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; + status = "okay"; +}; + +&pio { + uart1_pins: uart1-pins-g1 { + mux { + function = "uart"; + groups = "uart1_3"; + }; + }; +}; diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds index b3dceb74c47..69afdfde56d 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/01_leds @@ -32,6 +32,17 @@ cudy,re3000-v1) cudy,wr3000-v1) ucidef_set_led_netdev "wan" "wan" "blue:wan" "wan" ;; +glinet,gl-x3000|\ +glinet,gl-xe3000) + ucidef_set_led_default "power" "POWER" "green:power" "1" + ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0" + ucidef_set_led_netdev "5g_1" "5G_1" "green:5g:led1" "wwan0" + ucidef_set_led_netdev "5g_2" "5G_2" "green:5g:led2" "wwan0" + ucidef_set_led_netdev "5g_3" "5G_3" "green:5g:led3" "wwan0" + ucidef_set_led_netdev "5g_4" "5G_4" "green:5g:led4" "wwan0" + ucidef_set_led_netdev "wlan2g" "WLAN2G" "green:wifi2g" "phy0-ap0" + ucidef_set_led_netdev "wlan5g" "WLAN5G" "green:wifi5g" "phy1-ap0" + ;; mercusys,mr90x-v1) ucidef_set_led_netdev "lan-0" "lan-0" "green:lan-0" "lan0" "link tx rx" ucidef_set_led_netdev "lan-1" "lan-1" "green:lan-1" "lan1" "link tx rx" diff --git a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network index dbda950cc50..8e4fd8003c1 100644 --- a/target/linux/mediatek/filogic/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/filogic/base-files/etc/board.d/02_network @@ -50,7 +50,9 @@ mediatek_setup_interfaces() ucidef_set_interfaces_lan_wan "lan1" eth1 ;; glinet,gl-mt2500|\ - glinet,gl-mt3000) + glinet,gl-mt3000|\ + glinet,gl-x3000|\ + glinet,gl-xe3000) ucidef_set_interfaces_lan_wan eth1 eth0 ;; glinet,gl-mt6000|\ diff --git a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac index ebee1b931f9..facd2079c46 100644 --- a/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac +++ b/target/linux/mediatek/filogic/base-files/etc/hotplug.d/ieee80211/11_fix_wifi_mac @@ -74,7 +74,9 @@ case "$board" in [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_setbit_la $(macaddr_add $addr 1) > /sys${DEVPATH}/macaddress ;; - glinet,gl-mt6000) + glinet,gl-mt6000|\ + glinet,gl-x3000|\ + glinet,gl-xe3000) addr=$(mmc_get_mac_binary factory 0x04) [ "$PHYNBR" = "0" ] && echo "$addr" > /sys${DEVPATH}/macaddress [ "$PHYNBR" = "1" ] && macaddr_add $addr 1 > /sys${DEVPATH}/macaddress diff --git a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh index abb692fb41d..4df4370f0fd 100755 --- a/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh @@ -120,7 +120,9 @@ platform_do_upgrade() { default_do_upgrade "$1" ;; glinet,gl-mt2500|\ - glinet,gl-mt6000) + glinet,gl-mt6000|\ + glinet,gl-x3000|\ + glinet,gl-xe3000) CI_KERNPART="kernel" CI_ROOTPART="rootfs" emmc_do_upgrade "$1" @@ -216,6 +218,8 @@ platform_copy_config() { acer,predator-w6|\ glinet,gl-mt2500|\ glinet,gl-mt6000|\ + glinet,gl-x3000|\ + glinet,gl-xe3000|\ jdcloud,re-cp-03|\ ubnt,unifi-6-plus) emmc_copy_config diff --git a/target/linux/mediatek/image/filogic.mk b/target/linux/mediatek/image/filogic.mk index b1c043bef20..7d2fac56b65 100644 --- a/target/linux/mediatek/image/filogic.mk +++ b/target/linux/mediatek/image/filogic.mk @@ -535,6 +535,31 @@ define Device/glinet_gl-mt6000 endef TARGET_DEVICES += glinet_gl-mt6000 +define Device/glinet_gl-x3000-xe3000-common + DEVICE_VENDOR := GL.iNet + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-mt7981-firmware mt7981-wo-firmware mkf2fs \ + kmod-fs-f2fs kmod-hwmon-pwmfan kmod-usb3 kmod-usb-serial-option \ + kmod-usb-storage kmod-usb-net-qmi-wwan uqmi + IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata +endef + +define Device/glinet_gl-x3000 + DEVICE_MODEL := GL-X3000 + DEVICE_DTS := mt7981a-glinet-gl-x3000 + SUPPORTED_DEVICES := glinet,gl-x3000 + $(call Device/glinet_gl-x3000-xe3000-common) +endef +TARGET_DEVICES += glinet_gl-x3000 + +define Device/glinet_gl-xe3000 + DEVICE_MODEL := GL-XE3000 + DEVICE_DTS := mt7981a-glinet-gl-xe3000 + SUPPORTED_DEVICES := glinet,gl-xe3000 + $(call Device/glinet_gl-x3000-xe3000-common) +endef +TARGET_DEVICES += glinet_gl-xe3000 + define Device/h3c_magic-nx30-pro DEVICE_VENDOR := H3C DEVICE_MODEL := Magic NX30 Pro