From: Arınç ÜNAL Date: Wed, 29 Mar 2023 10:11:30 +0000 (+0300) Subject: ramips: add support for TOZED ZLT S12 PRO X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=ce1f9fa625ab7d2159b90d76df5030a55a3de419;p=openwrt%2Fstaging%2Fstintel.git ramips: add support for TOZED ZLT S12 PRO The TOZED ZLT S12 PRO is an AC1200 router featuring 4 Ethernet ports with a TOZED TL70-C cellular modem which supports the NCM mode. The stock firmware does SIM locking on the modem by stopping dialing when a different PLMN is detected. This is not the case on OpenWrt. Specifications: - CPU: MediaTek MT7621AT - RAM: 256MB DDR3 - NOR Flash: MX25L12833FM2I 16MB SPI Flash - Wi-Fi 2.4Ghz: MT7603E - Wi-Fi 5Ghz: MT7612E - Switch: MT7530 4x 1Gbit Ports - WWAN: Unisoc SL8563 based TOZED TL70-C LTE CAT6 cellular modem - USB: 1x optional USB2.0 external port - Switches/Buttons: WPS, Reset, Power Switch - LEDs: Power, Wi-Fi, Data, Signal 1-5, Phone Installation and TFTP Recovery: - Connect to serial console. - Boot initramfs image by choosing option 1 when U-Boot prompts. - Install sysupgrade image via OpenWrt. Serial Pins: Located at the bottom right when looking from the front, right under the Reset/WPS buttons. The pinout from the left is: - RX - GND - TX Baudrate is 115200. When connecting from a powered off state, disconnect RX as it blocks the boot process. Link: http://www.sztozed.com/en/contents/58/84.html Co-developed-by: Andre Cruz Signed-off-by: Andre Cruz Signed-off-by: Arınç ÜNAL --- diff --git a/target/linux/ramips/dts/mt7621_tozed_zlt-s12-pro.dts b/target/linux/ramips/dts/mt7621_tozed_zlt-s12-pro.dts new file mode 100644 index 0000000000..5a94bbda82 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_tozed_zlt-s12-pro.dts @@ -0,0 +1,245 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include +#include + +/ { + compatible = "tozed,zlt-s12-pro", "mediatek,mt7621-soc"; + model = "TOZED ZLT S12 PRO"; + + aliases { + led-boot = &led_power_blue; + led-failsafe = &led_power_yellow; + led-running = &led_power_blue; + led-upgrade = &led_power_blue; + label-mac-device = &wifi1; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led-modem-blue { + label = "blue:modem"; + gpios = <&gpio 33 GPIO_ACTIVE_LOW>; + }; + + led-modem-red { + label = "red:modem"; + gpios = <&gpio 27 GPIO_ACTIVE_LOW>; + }; + + led_power_blue: led-power-blue { + label = "blue:power"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + + led_power_yellow: led-power-yellow { + label = "yellow:power"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + }; + + led-wifi { + label = "blue:wifi"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led-signal1 { + label = "blue:signal1"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + }; + + led-signal2 { + label = "blue:signal2"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + }; + + led-signal3 { + label = "blue:signal3"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + }; + + led-signal4 { + label = "blue:signal4"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + + led-signal5 { + label = "blue:signal5"; + gpios = <&gpio 26 GPIO_ACTIVE_LOW>; + }; + + led-phone { + label = "blue:phone"; + gpios = <&gpio 31 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + button-reset { + label = "reset"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + button-rfkill { + label = "rfkill"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + button-wps { + label = "wps"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio_export { + compatible = "gpio-export"; + + lt72_ant0 { + gpio-export,name = "lt72_ant0"; + gpio-export,input = <0>; + gpios = <&gpio 6 GPIO_ACTIVE_HIGH>; + }; + + lt72_ant1 { + gpio-export,name = "lt72_ant1"; + gpio-export,input = <0>; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + }; + + lt72_power { + gpio-export,name = "lt72_power"; + gpio-export,output = <1>; + gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x8000>; + read-only; + }; + + // Stock config partition + partition@38000 { + label = "tozed-conf"; + reg = <0x38000 0x8000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_factory_e000: macaddr@e000 { + reg = <0xe000 0x6>; + }; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0xfb0000>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi0: mt76@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +&pcie1 { + wifi1: mt76@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + ieee80211-freq-limit = <2400000 2500000>; + }; +}; + +ðernet { + pinctrl-0 = <&mdio_pins>, <&rgmii1_pins>; +}; + +&gmac0 { + nvmem-cells = <&macaddr_factory_e000>; + nvmem-cell-names = "mac-address"; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "wan"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@4 { + status = "okay"; + label = "lan1"; + }; + }; +}; + +&state_default { + gpio { + groups = "wdt", "rgmii2", "jtag", "uart3"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index fc532966c8..f717fea5d4 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -2135,6 +2135,16 @@ define Device/totolink_x5000r endef TARGET_DEVICES += totolink_x5000r +define Device/tozed_zlt-s12-pro + $(Device/dsa-migration) + $(Device/uimage-lzma-loader) + IMAGE_SIZE := 16064k + DEVICE_VENDOR := TOZED + DEVICE_MODEL := ZLT S12 PRO + DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb3 comgt-ncm -uboot-envtools +endef +TARGET_DEVICES += tozed_zlt-s12-pro + define Device/tplink_archer-ax23-v1 $(Device/dsa-migration) $(Device/tplink-safeloader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 5b7cc7f2ca..176d15b730 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -108,6 +108,10 @@ ramips_setup_interfaces() mikrotik,routerboard-760igs) ucidef_set_interfaces_lan_wan "lan2 lan3 lan4 lan5" "wan sfp" ;; + tozed,zlt-s12-pro) + ucidef_set_interface "wwan" device "/dev/ttyUSB0" protocol "ncm" + uci add_list firewall.@zone[1].network='wwan' + ;; tplink,deco-m4r-v4) ucidef_set_interfaces_lan_wan "eth1" "eth0" ;; diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/03_gpio_switches b/target/linux/ramips/mt7621/base-files/etc/board.d/03_gpio_switches index ec2bf695a0..aebb416371 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/03_gpio_switches @@ -12,6 +12,9 @@ mikrotik,routerboard-760igs) telco-electronics,x1) ucidef_add_gpio_switch "modem_reset" "Modem Reset" "496" ;; +tozed,zlt-s12-pro) + ucidef_add_gpio_switch "lt72_power" "Power LTE modem" "lt72_power" "1" + ;; tplink,eap235-wall-v1|\ tplink,eap615-wall-v1) ucidef_add_gpio_switch "poe_passthrough" "PoE Passthrough" "poe-passthrough"