From: Andrew Pikler Date: Wed, 27 Jan 2021 17:35:49 +0000 (+0200) Subject: ramips: add support for Cudy WR1300 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=cd2b661453a8a2b8260dfb9b9c0dc5297b981331;p=openwrt%2Fstaging%2Fxback.git ramips: add support for Cudy WR1300 Specifications: - SoC: MediaTek MT7621AT - RAM: 128 MB (DDR3) - Flash: 16 MB (SPI NOR) - WiFi: MediaTek MT7603E, MediaTek MT7612E - Switch: 1 WAN, 4 LAN (Gigabit) - Ports: 1 USB 3.0 - Buttons: Reset, WPS - LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB - Power: DC 12V 1A tip positive UART Serial: 115200 baud Located on unpopulated 4 pin header near J4: J4 [o] Rx [o] Tx [o] GND [ ] Vcc - Do not connect Installation: Download and flash the manufacturer's built OpenWRT image available at http://www.cudytech.com/openwrt_software_download Install the new OpenWRT image via luci (System -> Backup/Flash firmware) Be sure to NOT keep settings. The force upgrade may need to be checked due to differences in router naming conventions. Recovery: - Loads only signed manufacture firmware due to bootloader RSA verification - serve tftp-recovery image as /recovery.bin on 192.168.1.88/24 - connect to any lan ethernet port - power on the device while holding the reset button - wait at least 8 seconds before releasing reset button for image to download - See http://www.cudytech.com/newsinfo/547425.html MAC addresses as verified by OEM firmware: use address source LAN *:f0 label WAN *:f1 label + 1 2g *:f0 label 5g *:f2 label + 2 The label MAC address is found in bdinfo 0xde00. Signed-off-by: Andrew Pikler --- diff --git a/target/linux/ramips/dts/mt7621_cudy_wr1300.dts b/target/linux/ramips/dts/mt7621_cudy_wr1300.dts new file mode 100644 index 0000000000..a66ce942a5 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_cudy_wr1300.dts @@ -0,0 +1,195 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + compatible = "cudy,wr1300", "mediatek,mt7621-soc"; + model = "Cudy WR1300"; + + aliases { + led-boot = &led_sys; + led-failsafe = &led_sys; + led-running = &led_sys; + led-upgrade = &led_sys; + label-mac-device = &gmac0; + }; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_sys: sys { + label = "green:sys"; + gpios = <&gpio 15 GPIO_ACTIVE_HIGH>; + }; + + usb { + label = "green:usb"; + gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; + trigger-sources = <&xhci_ehci_port1>, <&ehci_port2>; + linux,default-trigger = "usbport"; + }; + + wps { + label = "green:wps"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <80000000>; + m25p,fast-read; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x50000 0xf80000>; + }; + + partition@fd0000 { + label = "debug"; + reg = <0xfd0000 0x10000>; + read-only; + }; + + partition@fe0000 { + label = "backup"; + reg = <0xfe0000 0x10000>; + read-only; + }; + + bdinfo: partition@ff0000 { + label = "bdinfo"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "pci14c3,7603"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x0000>; + mtd-mac-address = <&bdinfo 0xde00>; + ieee80211-freq-limit = <2400000 2500000>; + + led { + led-active-low; + }; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "pci14c3,7662"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x8000>; + mtd-mac-address = <&bdinfo 0xde00>; + mtd-mac-address-increment = <2>; + ieee80211-freq-limit = <5000000 6000000>; + + led { + led-sources = <2>; + led-active-low; + }; + }; +}; + +&gmac0 { + mtd-mac-address = <&bdinfo 0xde00>; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan4"; + }; + + port@1 { + status = "okay"; + label = "lan3"; + }; + + port@2 { + status = "okay"; + label = "lan2"; + }; + + port@3 { + status = "okay"; + label = "lan1"; + }; + + port@4 { + status = "okay"; + label = "wan"; + mtd-mac-address = <&bdinfo 0xde00>; + mtd-mac-address-increment = <1>; + }; + }; +}; + +&state_default { + gpio { + groups = "wdt", "i2c", "jtag"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index 39a4d03a42..203ca1b908 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -222,6 +222,16 @@ define Device/buffalo_wsr-600dhp endef TARGET_DEVICES += buffalo_wsr-600dhp +define Device/cudy_wr1300 + $(Device/dsa-migration) + IMAGE_SIZE := 15872k + DEVICE_VENDOR := Cudy + DEVICE_MODEL := WR1300 + DEVICE_PACKAGES := kmod-mt7603 kmod-mt76x2 kmod-usb2 kmod-usb3 \ + kmod-usb-ledtrig-usbport +endef +TARGET_DEVICES += cudy_wr1300 + define Device/dlink_dir-8xx-a1 $(Device/dsa-migration) IMAGE_SIZE := 16000k