From: INAGAKI Hiroshi Date: Sat, 29 Dec 2018 15:55:35 +0000 (+0900) Subject: ath79: add support for ELECOM WRC-1750GHBK2-I/C X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=caf306ce912a46e2d1204b996c3b4fede9af6dae;p=openwrt%2Fstaging%2Fluka.git ath79: add support for ELECOM WRC-1750GHBK2-I/C ELECOM WRC-1750GHBK2-I/WRC-1750GHBK2-C are 2.4/5 GHz band 11ac routers, based on Qualcomm Atheros QCA9563. This commit also includes small fix; use "0x0x03000101" as pll_1000 instead of "0x03000000". Specification: - SoC: Qualcom Atheros QCA9563 - RAM: 128 MB (DDR2) - Flash: 16 MB (SPI-NOR) - WLAN: 2.4/5 GHz - 2.4 GHz: 2T2R (SoC internal) - 5 GHz: 3T3R (QCA9880) - Ethernet: 10/100/1000 Mbps - LED/key: 4x/3x (2x buttons, 1x slide-switch) - UART: through-hole on PCB - Vcc, RX, GND, TX from switch (QCA8337N) side - 115200n8 Flash instruction using factory image: 1. Boot WRC-1750GHBK2-I/C normaly 2. Access to "http://192.168.2.1/" and open firmware upgrade page ("ファームウェア更新 手動更新（アップデート）") 3. Select the OpenWrt factory image and click apply ("適用") button to perform firmware update 4. On the (initramfs) factory image, perform sysupgrade with squashfs-sysupgrade image 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi --- diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 1be7a63c85..83bede0961 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -77,6 +77,7 @@ ath79_setup_interfaces() ucidef_add_switch "switch0" \ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan" ;; + elecom,wrc-1750ghbk2-i|\ elecom,wrc-300ghbk2-i) ucidef_add_switch "switch0" \ "0@eth0" "2:lan:4" "3:lan:3" "4:lan:2" "5:lan:1" "1:wan" @@ -244,6 +245,7 @@ ath79_setup_macs() lan_mac=$(mtd_get_mac_ascii devdata "lanmac") wan_mac=$(mtd_get_mac_ascii devdata "wanmac") ;; + elecom,wrc-1750ghbk2-i|\ elecom,wrc-300ghbk2-i) wan_mac=$(macaddr_add "$(mtd_get_mac_binary ART 4098)" -2) ;; diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 7fe19c0604..45d3819c21 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -96,6 +96,9 @@ case "$FIRMWARE" in ath10kcal_extract "art" 20480 2116 ath10kcal_patch_mac $(mtd_get_mac_ascii devdata "wlan5mac") ;; + elecom,wrc-1750ghbk2-i) + ath10kcal_extract "ART" 20480 2116 + ;; glinet,ar750s|\ tplink,re450-v2) ath10kcal_extract "art" 20480 2116 diff --git a/target/linux/ath79/dts/qca9563_elecom_wrc-1750ghbk2-i.dts b/target/linux/ath79/dts/qca9563_elecom_wrc-1750ghbk2-i.dts new file mode 100644 index 0000000000..287dee6bb1 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_elecom_wrc-1750ghbk2-i.dts @@ -0,0 +1,56 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca9563_elecom_wrc-ghbk2-i.dtsi" + +/ { + model = "ELECOM WRC-1750GHBK2-I/C"; + compatible = "elecom,wrc-1750ghbk2-i", "qca,qca9563"; +}; + +&leds { + power: power { + label = "elecom:blue:power"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + wlan2g { + label = "elecom:blue:wlan2g"; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + + wlan5g { + label = "elecom:blue:wlan5g"; + gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; +}; + +&partitions { + partition@70000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x070000 0xf70000>; + }; + + partition@fe0000 { + label = "hwconfig"; + reg = <0xfe0000 0x010000>; + read-only; + }; + + ART: partition@ff0000 { + label = "ART"; + reg = <0xff0000 0x010000>; + read-only; + }; +}; + +&pcie { + status = "okay"; +}; diff --git a/target/linux/ath79/dts/qca9563_elecom_wrc-300ghbk2-i.dts b/target/linux/ath79/dts/qca9563_elecom_wrc-300ghbk2-i.dts index bb1f350150..c823f4a342 100644 --- a/target/linux/ath79/dts/qca9563_elecom_wrc-300ghbk2-i.dts +++ b/target/linux/ath79/dts/qca9563_elecom_wrc-300ghbk2-i.dts @@ -4,156 +4,43 @@ #include #include -#include "qca956x.dtsi" +#include "qca9563_elecom_wrc-ghbk2-i.dtsi" / { model = "ELECOM WRC-300GHBK2-I"; compatible = "elecom,wrc-300ghbk2-i", "qca,qca9563"; +}; - chosen { - bootargs = "console=ttyS0,115200n8"; - }; - - aliases { - led-boot = &power; - led-failsafe = &power; - led-running = &power; - led-upgrade = &power; +&leds { + power: power { + label = "elecom:white:power"; + gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; + default-state = "on"; }; - leds { - compatible = "gpio-leds"; - - power: power { - label = "wrc-300ghbk2-i:white:power"; - gpios = <&gpio 1 GPIO_ACTIVE_HIGH>; - default-state = "on"; - }; - - wlan2g { - label = "wrc-300ghbk2-i:white:wlan2g"; - gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; - linux,default-trigger = "phy0tpt"; - }; - - wps { - label = "wrc-300ghbk2-i:red:wps"; - gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; - }; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&gpio 2 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - }; - - button_wps { - label = "wps"; - gpios = <&gpio 5 GPIO_ACTIVE_LOW>; - linux,code = ; - debounce-interval = <60>; - }; - - ap { - label = "ap"; - gpios = <&gpio 6 GPIO_ACTIVE_LOW>; - linux,code = ; - linux,input-type = ; - debounce-interval = <60>; - }; + wlan2g { + label = "elecom:white:wlan2g"; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; }; }; -&spi { - status = "okay"; - num-cs = <1>; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <25000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x000000 0x040000>; - read-only; - }; - - partition@40000 { - label = "u-boot-env"; - reg = <0x040000 0x010000>; - read-only; - }; - - partition@50000 { - label = "nvram"; - reg = <0x050000 0x020000>; - read-only; - }; - - partition@70000 { - compatible = "denx,uimage"; - label = "firmware"; - reg = <0x070000 0x770000>; - }; - - partition@7e0000 { - label = "hwconfig"; - reg = <0x7e0000 0x010000>; - read-only; - }; - - ART: partition@7f0000 { - label = "ART"; - reg = <0x7f0000 0x010000>; - read-only; - }; - }; +&partitions { + partition@70000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x070000 0x770000>; }; -}; - -&mdio0 { - status = "okay"; - - phy0: ethernet-phy@0 { - reg = <0>; - phy-mode = "sgmii"; - qca,ar8327-initvals = < - 0x04 0x00000080 /* PORT0 PAD MODE CTRL */ - 0x50 0xcf37cf37 /* LED_CTRL0 */ - 0x54 0x00000000 /* LED_CTRL1 */ - 0x58 0x00000000 /* LED_CTRL2 */ - 0x5c 0x03ffff00 /* LED_CTRL3 */ - 0x7c 0x0000007e /* PORT0_STATUS */ - >; + partition@7e0000 { + label = "hwconfig"; + reg = <0x7e0000 0x010000>; + read-only; }; -}; - -ð0 { - status = "okay"; - - mtd-mac-address = <&ART 0x1002>; - mtd-mac-address-increment = <(-1)>; - phy-mode = "sgmii"; - phy-handle = <&phy0>; -}; -&uart { - status = "okay"; -}; - -&wmac { - status = "okay"; - mtd-cal-data = <&ART 0x1000>; + ART: partition@7f0000 { + label = "ART"; + reg = <0x7f0000 0x010000>; + read-only; + }; }; diff --git a/target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi b/target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi new file mode 100644 index 0000000000..8d5bbe180c --- /dev/null +++ b/target/linux/ath79/dts/qca9563_elecom_wrc-ghbk2-i.dtsi @@ -0,0 +1,127 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca956x.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + leds: leds { + compatible = "gpio-leds"; + + wps { + label = "elecom:red:wps"; + gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + button_wps { + label = "wps"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + linux,code = ; + debounce-interval = <60>; + }; + + ap { + label = "ap"; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + debounce-interval = <60>; + }; + }; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions: partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + read-only; + }; + + partition@50000 { + label = "nvram"; + reg = <0x050000 0x020000>; + read-only; + }; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy0: ethernet-phy@0 { + reg = <0>; + + qca,ar8327-initvals = < + 0x04 0x00000080 /* PORT0 PAD MODE CTRL */ + 0x50 0xcf37cf37 /* LED_CTRL0 */ + 0x54 0x00000000 /* LED_CTRL1 */ + 0x58 0x00000000 /* LED_CTRL2 */ + 0x5c 0x03ffff00 /* LED_CTRL3 */ + 0x7c 0x0000007e /* PORT0_STATUS */ + >; + }; +}; + +ð0 { + status = "okay"; + + pll-data = <0x03000101 0x00000101 0x00001919>; + + mtd-mac-address = <&ART 0x1002>; + mtd-mac-address-increment = <(-1)>; + phy-mode = "sgmii"; + phy-handle = <&phy0>; +}; + +&uart { + status = "okay"; +}; + +&wmac { + status = "okay"; + mtd-cal-data = <&ART 0x1000>; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 2f9b2c9d7e..31c62f659d 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -221,6 +221,17 @@ define Device/dlink_dir-859-a1 endef TARGET_DEVICES += dlink_dir-859-a1 +define Device/elecom_wrc-1750ghbk2-i + ATH_SOC := qca9563 + DEVICE_TITLE := ELECOM WRC-1750GHBK2-I/C + IMAGE_SIZE := 15808k + KERNEL_INITRAMFS := $$(KERNEL) | pad-to 2 | \ + elecom-header 16187314 RN68 WRC-1750GHBK2 \ + $(KDIR)/tmp/$$(KERNEL_INITRAMFS_PREFIX)-factory.bin + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca988x-ct +endef +TARGET_DEVICES += elecom_wrc-1750ghbk2-i + define Device/elecom_wrc-300ghbk2-i ATH_SOC := qca9563 DEVICE_TITLE := ELECOM WRC-300GHBK2-I