From: Shiji Yang Date: Fri, 20 Jan 2023 03:16:33 +0000 (+0000) Subject: ath79: improve support for Letv LBA-047-CH X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=c7059c56a85567ce6bc943960168b19e2572508b;p=openwrt%2Fstaging%2Frobimarko.git ath79: improve support for Letv LBA-047-CH 1. Convert wireless calibration data to NVMEM. 2. Enable control green status LED and change default LED behaviors. The three LEDs of LBA-047-CH are in the same position, and the green LED will be completely covered by the other two LEDs. So don's use green LED as WAN indicator to ensure that only one LED is on at a time. LED Factory OpenWrt blue internet fail failsafe && upgrade green internet okay run red boot boot 3. Reduce the SPI clock to 30 MHz because the ath79 target does not support 50 MHz SPI operation well. Keep the fast-read support to ensure the spi-mem feature (b3f9842330) is enabled. 4. Remove unused package "uboot-envtools". 5. Split the factory image into two parts: rootfs and kernel. This change can reduce the factory image size and allow users to upgrade the OpenWrt kernel loader uImage (OKLI) independently. The new installation method: First, rename "squashfs-kernel.bin" to "openwrt-ar71xx-generic-ap147-16M-kernel.bin" and rename "rootfs.bin" to "openwrt-ar71xx-generic-ap147-16M-rootfs-squashfs.bin". Then we can press reset button for about 5 seconds to enter tftp download mode. Finally, set IP address to 192.168.67.100 and upload the above two parts via tftp server. Tested on Letv LBA-047-CH Signed-off-by: Shiji Yang --- diff --git a/target/linux/ath79/dts/qca9531_letv_lba-047-ch.dts b/target/linux/ath79/dts/qca9531_letv_lba-047-ch.dts index d65417c0d5..586facc9e5 100644 --- a/target/linux/ath79/dts/qca9531_letv_lba-047-ch.dts +++ b/target/linux/ath79/dts/qca9531_letv_lba-047-ch.dts @@ -4,6 +4,7 @@ #include #include +#include #include / { @@ -11,11 +12,11 @@ compatible = "letv,lba-047-ch", "qca,qca9531"; aliases { - led-boot = &led_status_red; - led-failsafe = &led_status_red; - led-running = &led_status_blue; - led-upgrade = &led_status_red; label-mac-device = ð0; + led-boot = &led_status_red; + led-failsafe = &led_status_blue; + led-running = &led_status_green; + led-upgrade = &led_status_blue; }; keys { @@ -31,16 +32,24 @@ leds { compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_wan_pin>; - - led_status_blue: status_blue { + led_status_blue: led-0 { label = "blue:status"; + color = ; + function = LED_FUNCTION_STATUS; gpios = <&gpio 13 GPIO_ACTIVE_LOW>; }; - led_status_red: status_red { + led_status_green: led-1 { + label = "green:status"; + color = ; + function = LED_FUNCTION_STATUS; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + led_status_red: led-2 { label = "red:status"; + color = ; + function = LED_FUNCTION_STATUS; gpios = <&gpio 11 GPIO_ACTIVE_LOW>; }; }; @@ -64,20 +73,13 @@ }; }; -&pinmux { - /* GPIO 4: LED_LINK_5 (WAN) */ - led_wan_pin: pinmux_led_wan_pin { - pinctrl-single,bits = <0x04 0x0000002d 0x000000ff>; - }; -}; - &spi { status = "okay"; flash@0 { compatible = "jedec,spi-nor"; reg = <0>; - spi-max-frequency = <50000000>; + spi-max-frequency = <30000000>; m25p,fast-read; partitions { @@ -112,10 +114,26 @@ reg = <0xe90000 0x160000>; }; - art: partition@ff0000 { + partition@ff0000 { label = "art"; reg = <0xff0000 0x10000>; read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_art_0: macaddr@0 { + reg = <0x0 0x6>; + }; + + macaddr_art_6: macaddr@6 { + reg = <0x6 0x6>; + }; + + cal_art_1000: calibration@1000 { + reg = <0x1000 0x440>; + }; }; }; }; @@ -140,19 +158,6 @@ &wmac { status = "okay"; - mtd-cal-data = <&art 0x1000>; -}; - -&art { - compatible = "nvmem-cells"; - #address-cells = <1>; - #size-cells = <1>; - - macaddr_art_0: macaddr@0 { - reg = <0x0 0x6>; - }; - - macaddr_art_6: macaddr@6 { - reg = <0x6 0x6>; - }; + nvmem-cells = <&cal_art_1000>; + nvmem-cell-names = "calibration"; }; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index b3b510a2ec..0837d37a30 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1645,13 +1645,15 @@ define Device/letv_lba-047-ch SOC := qca9531 DEVICE_VENDOR := Letv DEVICE_MODEL := LBA-047-CH + DEVICE_PACKAGES := -uboot-envtools + FACTORY_SIZE := 14528k IMAGE_SIZE := 15936k LOADER_FLASH_OFFS := 0x50000 KERNEL := kernel-bin | append-dtb | lzma | uImage lzma -M 0x4f4b4c49 - IMAGES += factory.bin - IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \ - append-rootfs | pad-rootfs | check-size | pad-to 14528k | \ - append-loader-okli-uimage $(1) | pad-to 64k + IMAGES += kernel.bin rootfs.bin + IMAGE/kernel.bin := append-loader-okli-uimage $(1) | pad-to 64k + IMAGE/rootfs.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \ + append-rootfs | pad-rootfs | check-size $$$$(FACTORY_SIZE) endef TARGET_DEVICES += letv_lba-047-ch