From: Piotr Dymacz Date: Tue, 29 Jan 2019 17:12:51 +0000 (+0100) Subject: ipq40xx: add support for ALFA Network AP120C-AC X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=c568c6dc09f0a847097fb9697369114a251f096d;p=openwrt%2Fstaging%2Fdedeckeh.git ipq40xx: add support for ALFA Network AP120C-AC ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 4x LED (all driven by GPIO) - 1x button (reset) - 1x USB 2.0 (optional, not installed in indoor version) - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) Flash instruction: 1. This board uses dual-image feature (128 MB NAND is divided into two 64 MB partitions: 'rootfs1' and 'rootfs2'). 2. Before update, make sure your device is running firmware no older than v1.1 (previous versions have incompatible U-Boot). 3. Use 'factory' image in vendor GUI or for sysupgrade tool, without preserving settings. Signed-off-by: Piotr Dymacz --- diff --git a/target/linux/ipq40xx/base-files/etc/board.d/01_leds b/target/linux/ipq40xx/base-files/etc/board.d/01_leds index 9105bf2452..2fca1cbc9f 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/01_leds +++ b/target/linux/ipq40xx/base-files/etc/board.d/01_leds @@ -11,6 +11,9 @@ board=$(board_name) boardname="${board##*,}" case "$board" in +alfa-network,ap120c-ac) + ucidef_set_led_netdev "wan" "WAN" "${boardname}:amber:wan" "eth1" + ;; asus,rt-ac58u) ucidef_set_led_wlan "wlan2g" "WLAN2G" "${boardname}:blue:wlan2G" "phy0tpt" ucidef_set_led_wlan "wlan5g" "WLAN5G" "${boardname}:blue:wlan5G" "phy1tpt" diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index 43be592071..b28f5ef12c 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -12,7 +12,8 @@ ipq40xx_setup_interfaces() local board="$1" case "$board" in - 8dev,jalapeno) + 8dev,jalapeno|\ + alfa-network,ap120c-ac) ucidef_set_interfaces_lan_wan "eth0" "eth1" ;; asus,map-ac2200|\ diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 21d9063fd4..718224f1e0 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -119,6 +119,7 @@ case "$FIRMWARE" in "ath10k/pre-cal-ahb-a000000.wifi.bin") case "$board" in 8dev,jalapeno |\ + alfa-network,ap120c-ac |\ glinet,gl-b1300 |\ linksys,ea6350v3 |\ qcom,ap-dk01.1-c1) @@ -160,6 +161,7 @@ case "$FIRMWARE" in "ath10k/pre-cal-ahb-a800000.wifi.bin") case "$board" in 8dev,jalapeno |\ + alfa-network,ap120c-ac |\ glinet,gl-b1300 |\ linksys,ea6350v3 |\ qcom,ap-dk01.1-c1) diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount new file mode 100755 index 0000000000..604f88c396 --- /dev/null +++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount @@ -0,0 +1,14 @@ +#!/bin/sh /etc/rc.common + +START=99 + +start() { + . /lib/functions.sh + + case $(board_name) in + alfa-network,ap120c-ac) + [ -n "$(fw_printenv bootcount changed 2>/dev/null)" ] &&\ + echo -e "bootcount\nchanged\n" | /usr/sbin/fw_setenv -s - + ;; + esac +} diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index f6bc173a76..b92a2bfe9f 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -46,7 +46,8 @@ zyxel_do_upgrade() { platform_do_upgrade() { case "$(board_name)" in - 8dev,jalapeno) + 8dev,jalapeno |\ + alfa-network,ap120c-ac) nand_do_upgrade "$ARGV" ;; asus,map-ac2200) @@ -81,6 +82,16 @@ platform_do_upgrade() { platform_nand_pre_upgrade() { case "$(board_name)" in + alfa-network,ap120c-ac) + part="$(awk -F 'ubi.mtd=' '{printf $2}' /proc/cmdline | sed -e 's/ .*$//')" + if [ "$part" = "rootfs1" ]; then + fw_setenv active 2 || exit 1 + CI_UBIPART="rootfs2" + else + fw_setenv active 1 || exit 1 + CI_UBIPART="rootfs1" + fi + ;; asus,rt-ac58u) CI_UBIPART="UBI_DEV" CI_KERNPART="linux" diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts new file mode 100644 index 0000000000..63e3426568 --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts @@ -0,0 +1,343 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "ALFA Network AP120C-AC"; + compatible = "alfa-network,ap120c-ac", "qcom,ipq4019"; + + aliases { + led-boot = &status; + led-failsafe = &status; + led-running = &status; + led-upgrade = &status; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + status: status { + label = "ap120c-ac:blue:status"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wan { + label = "ap120c-ac:amber:wan"; + gpios = <&qca8075 19 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + label = "ap120c-ac:green:wlan2g"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "ap120c-ac:red:wlan5g"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + }; + + soc { + mdio@90000 { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + phys = <&usb3_hs_phy>; + phy-names = "usb2-phy"; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + qca8075: ess-switch@c000000 { + status = "okay"; + + switch_lan_bmp = <0x10>; + switch_wan_bmp = <0x20>; + + #gpio-cells = <2>; + gpio-controller; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_i2c3 { + status = "okay"; + + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + + tpm@29 { + compatible = "atmel,at97sc3204t"; + reg = <0x29>; + }; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, + <&tlmm 4 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition@d0000 { + label = "DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition@e0000 { + label = "APPSBLENV"; + reg = <0x000e0000 0x00010000>; + }; + + partition@f0000 { + label = "APPSBL"; + reg = <0x000f0000 0x00080000>; + read-only; + }; + + partition@170000 { + label = "ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + + partition@180000 { + label = "priv_data1"; + reg = <0x00180000 0x00010000>; + read-only; + }; + + partition@190000 { + label = "priv_data2"; + reg = <0x00190000 0x00010000>; + read-only; + }; + }; + }; + + nand@1 { + compatible = "spinand,mt29f"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs1"; + reg = <0x00000000 0x04000000>; + }; + + partition@4000000 { + label = "rootfs2"; + reg = <0x04000000 0x04000000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial0_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + qcom,forced_duplex = <1>; + qcom,forced_speed = <1000>; + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + vlan_tag = <1 0x10>; +}; + +&gmac1 { + qcom,forced_duplex = <1>; + qcom,forced_speed = <1000>; + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + vlan_tag = <2 0x20>; +}; + +&tlmm { + i2c0_pins: i2c0_pinmux { + mux_i2c { + function = "blsp_i2c0"; + pins = "gpio58", "gpio59"; + drive-strength = <16>; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_mdio { + pins = "gpio53"; + function = "mdio"; + bias-pull-up; + }; + + mux_mdc { + pins = "gpio52"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial0_pins: serial0_pinmux { + mux_uart { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi0_pins: spi0_pinmux { + mux_spi { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54", "gpio4"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; +}; + +&wifi1 { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts new file mode 100644 index 0000000000..0c73539ee1 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ap120c-ac.dts @@ -0,0 +1,347 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "ALFA Network AP120C-AC"; + compatible = "alfa-network,ap120c-ac"; + + aliases { + led-boot = &status; + led-failsafe = &status; + led-running = &status; + led-upgrade = &status; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + status: status { + label = "ap120c-ac:blue:status"; + gpios = <&tlmm 5 GPIO_ACTIVE_LOW>; + default-state = "keep"; + }; + + wan { + label = "ap120c-ac:amber:wan"; + gpios = <&qca8075 19 GPIO_ACTIVE_HIGH>; + }; + + wlan2g { + label = "ap120c-ac:green:wlan2g"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tpt"; + }; + + wlan5g { + label = "ap120c-ac:red:wlan5g"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy1tpt"; + }; + }; + + soc { + rng@22000 { + status = "okay"; + }; + + mdio@90000 { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + counter@4a1000 { + compatible = "qcom,qca-gcnt"; + reg = <0x4a1000 0x4>; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + + dwc3@8a00000 { + phys = <&usb3_hs_phy>; + phy-names = "usb2-phy"; + }; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + qca8075: ess-switch@c000000 { + status = "okay"; + + switch_lan_bmp = <0x10>; + switch_wan_bmp = <0x20>; + + #gpio-cells = <2>; + gpio-controller; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_i2c3 { + status = "okay"; + + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + + tpm@29 { + compatible = "atmel,at97sc3204t"; + reg = <0x29>; + }; +}; + +&blsp1_spi1 { + status = "okay"; + + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, + <&tlmm 4 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + + partition@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + + partition@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + + partition@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + + partition@d0000 { + label = "DDRPARAMS"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + + partition@e0000 { + label = "APPSBLENV"; + reg = <0x000e0000 0x00010000>; + }; + + partition@f0000 { + label = "APPSBL"; + reg = <0x000f0000 0x00080000>; + read-only; + }; + + partition@170000 { + label = "ART"; + reg = <0x00170000 0x00010000>; + read-only; + }; + + partition@180000 { + label = "priv_data1"; + reg = <0x00180000 0x00010000>; + read-only; + }; + + partition@190000 { + label = "priv_data2"; + reg = <0x00190000 0x00010000>; + read-only; + }; + }; + }; + + nand@1 { + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "rootfs1"; + reg = <0x00000000 0x04000000>; + }; + + partition@4000000 { + label = "rootfs2"; + reg = <0x04000000 0x04000000>; + }; + }; + }; +}; + +&blsp1_uart1 { + status = "okay"; + + pinctrl-0 = <&serial0_pins>; + pinctrl-names = "default"; +}; + +&cryptobam { + status = "okay"; +}; + +&gmac0 { + qcom,forced_duplex = <1>; + qcom,forced_speed = <1000>; + qcom,phy_mdio_addr = <3>; + qcom,poll_required = <1>; + vlan_tag = <1 0x10>; +}; + +&gmac1 { + qcom,forced_duplex = <1>; + qcom,forced_speed = <1000>; + qcom,phy_mdio_addr = <4>; + qcom,poll_required = <1>; + vlan_tag = <2 0x20>; +}; + +&tlmm { + i2c0_pins: i2c0_pinmux { + mux_i2c { + function = "blsp_i2c0"; + pins = "gpio58", "gpio59"; + drive-strength = <16>; + bias-disable; + }; + }; + + mdio_pins: mdio_pinmux { + mux_mdio { + pins = "gpio53"; + function = "mdio"; + bias-pull-up; + }; + + mux_mdc { + pins = "gpio52"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial0_pins: serial0_pinmux { + mux_uart { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi0_pins: spi0_pinmux { + mux_spi { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54", "gpio4"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&wifi0 { + status = "okay"; +}; + +&wifi1 { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 31468fd758..f7e7ba3d0f 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -62,6 +62,21 @@ define Device/8dev_jalapeno endef TARGET_DEVICES += 8dev_jalapeno +define Device/alfa-network_ap120c-ac + $(call Device/FitImage) + $(call Device/UbiFit) + DEVICE_TITLE := ALFA Network AP120C-AC + DEVICE_DTS := qcom-ipq4018-ap120c-ac + DEVICE_PACKAGES := ipq-wifi-alfa-network_ap120c-ac kmod-usb-acm \ + kmod-tpm-i2c-atmel uboot-envtools + BLOCKSIZE := 128k + PAGESIZE := 2048 + IMAGE_SIZE := 65536k + IMAGES := nand-factory.bin nand-sysupgrade.bin + IMAGE/nand-factory.bin := append-ubi | qsdk-ipq-factory-nand +endef +TARGET_DEVICES += alfa-network_ap120c-ac + define Device/asus_map-ac2200 $(call Device/FitImageLzma) DEVICE_DTS := qcom-ipq4019-map-ac2200 diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch index 20ea3a8449..551ac6f109 100644 --- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch @@ -10,11 +10,12 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,23 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ + qcom-ipq4018-a42.dtb \ ++ qcom-ipq4018-ap120c-ac.dtb \ + qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ + qcom-ipq4018-ex6100v2.dtb \ diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index f3472b32c0..0e27eeab65 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,11 +10,12 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,26 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,27 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ + qcom-ipq4018-a42.dtb \ ++ qcom-ipq4018-ap120c-ac.dtb \ + qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ + qcom-ipq4018-ex6100v2.dtb \