From: David Bauer Date: Wed, 8 Aug 2018 20:13:44 +0000 (+0200) Subject: ath79: add support for OCEDO Koala X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=c4931713df8ffb3c4e5c1be7d0b6d4aa96a7dd4c;p=openwrt%2Fstaging%2Fblocktrron.git ath79: add support for OCEDO Koala This commit adds support for the OCEDO Koala SOC: Qualcomm QCA9558 (Scorpion) RAM: 128MB FLASH: 16MiB WLAN1: QCA9558 2.4 GHz 802.11bgn 3x3 WLAN2: QCA9880 5 GHz 802.11nac 3x3 INPUT: RESET button LED: Power, LAN, WiFi 2.4, WiFi 5, SYS Serial: Header Next to Black metal shield Pinout is 3.3V - GND - TX - RX (Arrow Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi - 5 GHz WiFi - TFTP boot from ramdisk image - Installation via ramdisk image - OpenWRT sysupgrade - Buttons - LEDs Installation seems to be possible only through booting an OpenWRT ramdisk image. Hold down the reset button while powering on the device. It will load a ramdisk image named 'koala-uImage-initramfs-lzma.bin' from 192.168.100.8. Note: depending on the present software, the device might also try to pull a file called 'koala-uimage-factory'. Only the name differs, it is still used as a ramdisk image. Wait for the ramdisk image to boot. OpenWRT can be written to the flash via sysupgrade or mtd. Due to the flip-flop bootloader which we not (yet) support, you need to set the partition the bootloader is selecting. It is possible from the initramfs image with > fw_setenv bootcmd run bootcmd_1 Afterwards you can reboot the device. Signed-off-by: David Bauer --- diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 4d9d2e8fe0..aa0bf4514f 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -14,6 +14,7 @@ board=$(board_name) case "$board" in glinet,ar300m|\ +ocedo,koala|\ ocedo,raccoon|\ openmesh,om5p-ac-v2) ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x10000" "0x10000" diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 573bc80462..bbb30aa0cc 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -10,6 +10,7 @@ ath79_setup_interfaces() case "$board" in avm,fritz300e|\ + ocedo,koala|\ ocedo,raccoon|\ pcs,cap324|\ tplink,re450-v2|\ diff --git a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 038573f3e8..57d9744af2 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -87,6 +87,10 @@ board=$(board_name) case "$FIRMWARE" in "ath10k/cal-pci-0000:00:00.0.bin") case $board in + ocedo,koala) + ath10kcal_extract "art" 20480 2116 + ath10kcal_patch_mac $(mtd_get_mac_binary art 12) + ;; openmesh,om5p-ac-v2) ath10kcal_extract "ART" 20480 2116 ath10kcal_patch_mac $(macaddr_add $(cat /sys/class/net/eth0/address) +16) diff --git a/target/linux/ath79/dts/qca9558_ocedo_koala.dts b/target/linux/ath79/dts/qca9558_ocedo_koala.dts new file mode 100644 index 0000000000..6020e469a3 --- /dev/null +++ b/target/linux/ath79/dts/qca9558_ocedo_koala.dts @@ -0,0 +1,169 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "qca9557.dtsi" + +/ { + compatible = "ocedo,koala", "qca,qca9557"; + model = "OCEDO Koala"; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-status = &system; + }; + + leds { + compatible = "gpio-leds"; + + power { + label = "koala:green:power"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + wifi2 { + label = "koala:yellow:wlan2"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + default-state = "off"; + }; + + wifi5 { + label = "koala:red:wlan58"; + gpios = <&gpio 13 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + default-state = "off"; + }; + + system: system { + label = "koala:blue:sys"; + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + keys { + compatible = "gpio-keys-polled"; + poll-interval = <100>; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pcie0 { + status = "okay"; +}; + +&uart { + status = "okay"; +}; + +&pll { + clocks = <&extosc>; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + label = "firmware"; + reg = <0x050000 0x740000>; + }; + + partition@790000 { + label = "vendor"; + reg = <0x790000 0x740000>; + read-only; + }; + + partition@ed0000 { + label = "data"; + reg = <0xed0000 0x110000>; + read-only; + }; + + partition@fe0000 { + label = "id"; + reg = <0xfe0000 0x010000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&art 0x06>; +}; + +&mdio0 { + status = "okay"; + + phy5: ethernet-phy@5 { + reg = <5>; + phy-mode = "rgmii-rxid"; + + at803x-disable-smarteee; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&art 0x00>; + + phy-handle = <&phy5>; + phy-mode = "rgmii-rxid"; + + pll-data = <0xae000000 0xa0000101 0xa0001313>; + + gmac-config { + device = <&gmac>; + + rxdv-delay = <3>; + rxd-delay = <3>; + txen-delay = <0>; + txd-delay = <0>; + rgmii-enabled = <1>; + }; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index a6de86eade..614b3371f3 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -57,6 +57,16 @@ define Device/glinet_ar300m_nor endef TARGET_DEVICES += glinet_ar300m_nor +define Device/ocedo_koala + ATH_SOC := qca9558 + DEVICE_TITLE := OCEDO Koala + DEVICE_PACKAGES := kmod-ath10k ath10k-firmware-qca988x + SUPPORTED_DEVICES += koala + IMAGE_SIZE := 7424k + IMAGE/sysupgrade.bin := append-kernel | append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE) +endef +TARGET_DEVICES += ocedo_koala + define Device/ocedo_raccoon ATH_SOC := ar9344 DEVICE_TITLE := OCEDO Raccoon