From: Wenli Looi Date: Sat, 12 Jun 2021 23:32:33 +0000 (-0700) Subject: ath79: add partial support for Netgear EX7300v2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=c32008a37b81d0ab1062993241a1e9f0a8e73102;p=openwrt%2Fstaging%2Fthess.git ath79: add partial support for Netgear EX7300v2 Hardware -------- SoC: QCN5502 Flash: 16 MiB RAM: 128 MiB Ethernet: 1 gigabit port Wireless No1: QCN5502 on-chip 2.4GHz 4x4 Wireless No2: QCA9984 pcie 5GHz 4x4 USB: none Installation ------------ Flash the factory image using the stock web interface or TFTP the factory image to the bootloader. What works ---------- - LEDs - Ethernet port - 5GHz wifi (QCA9984 pcie) What doesn't work ----------------- - 2.4GHz wifi (QCN5502 on-chip) (I was not able to make this work, probably because ath9k requires some changes to support QCN5502.) Signed-off-by: Wenli Looi --- diff --git a/package/boot/uboot-envtools/files/ath79 b/package/boot/uboot-envtools/files/ath79 index 8cc0f59764..20715eb678 100644 --- a/package/boot/uboot-envtools/files/ath79 +++ b/package/boot/uboot-envtools/files/ath79 @@ -39,6 +39,7 @@ glinet,gl-ar750s-nor-nand|\ librerouter,librerouter-v1|\ netgear,ex6400|\ netgear,ex7300|\ +netgear,ex7300-v2|\ netgear,wndr4300-v2|\ netgear,wndr4500-v3|\ netgear,wnr1000-v2|\ diff --git a/target/linux/ath79/dts/qcn5502_netgear_ex7300-v2.dts b/target/linux/ath79/dts/qcn5502_netgear_ex7300-v2.dts new file mode 100644 index 0000000000..ba8dae0b36 --- /dev/null +++ b/target/linux/ath79/dts/qcn5502_netgear_ex7300-v2.dts @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca956x.dtsi" + +#include +#include + +/ { + model = "Netgear EX7300 v2"; + compatible = "netgear,ex7300-v2", "qca,qcn5500", "qca,qca9560"; + + aliases { + led-boot = &led_power_green; + led-failsafe = &led_power_amber; + led-running = &led_power_green; + led-upgrade = &led_power_amber; + label-mac-device = ð0; + }; + + led_spi { + compatible = "spi-gpio"; + #address-cells = <1>; + #size-cells = <0>; + + sck-gpios = <&gpio 14 GPIO_ACTIVE_HIGH>; + mosi-gpios = <&gpio 0 GPIO_ACTIVE_HIGH>; + num-chipselects = <0>; + + led_gpio: led_gpio@0 { + compatible = "fairchild,74hc595"; + reg = <0>; + gpio-controller; + #gpio-cells = <2>; + registers-number = <1>; + spi-max-frequency = <500000>; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_power_green: power_green { + label = "green:power"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + + led_power_amber: power_amber { + label = "amber:power"; + gpios = <&led_gpio 7 GPIO_ACTIVE_LOW>; + }; + + wps_green { + label = "green:wps"; + gpios = <&led_gpio 6 GPIO_ACTIVE_LOW>; + }; + + router_red { + label = "red:router"; + gpios = <&led_gpio 5 GPIO_ACTIVE_LOW>; + }; + + router_green { + label = "green:router"; + gpios = <&led_gpio 4 GPIO_ACTIVE_LOW>; + }; + + client_red { + label = "red:client"; + gpios = <&led_gpio 3 GPIO_ACTIVE_LOW>; + }; + + client_green { + label = "green:client"; + gpios = <&led_gpio 2 GPIO_ACTIVE_LOW>; + }; + + left_blue { + label = "blue:left"; + gpios = <&led_gpio 1 GPIO_ACTIVE_LOW>; + }; + + right_blue { + label = "blue:right"; + gpios = <&led_gpio 0 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + wps { + label = "WPS button"; + linux,code = ; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + + extender_apmode { + label = "EXTENDER/APMODE switch"; + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; + linux,code = ; + linux,input-type = ; + debounce-interval = <60>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pll { + clocks = <&extosc>; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + uboot: partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + read-only; + }; + + partition@50000 { + label = "config"; + reg = <0x050000 0x010000>; + }; + + partition@60000 { + label = "pot"; + reg = <0x060000 0x010000>; + read-only; + }; + + partition@70000 { + label = "firmware"; + reg = <0x70000 0xe30000>; + compatible = "denx,uimage"; + }; + + partition@ea0000 { + label = "rae"; + reg = <0xea0000 0x100000>; + read-only; + }; + + partition@fa0000 { + label = "oopsdump"; + reg = <0xfa0000 0x40000>; + read-only; + }; + + artmtd: partition@fe0000 { + label = "artmtd"; + reg = <0xfe0000 0x10000>; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +/* +Does not work due to lack of QCN5502 support in ath9k. +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; + mtd-mac-address = <&artmtd 0x6>; +}; +*/ + +&mdio0 { + status = "okay"; + + phy5: ethernet-phy@5 { + reg = <5>; + phy-mode = "sgmii"; + }; +}; + +ð0 { + status = "okay"; + + mtd-mac-address = <&artmtd 0x0>; + + phy-handle = <&phy5>; + phy-mode = "sgmii"; + + pll-data = <0x03000000 0x00000101 0x00001313>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 83e74f0651..b80f8cd266 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -44,6 +44,7 @@ ath79_setup_interfaces() meraki,mr16|\ netgear,ex6400|\ netgear,ex7300|\ + netgear,ex7300-v2|\ ocedo,koala|\ ocedo,raccoon|\ onion,omega|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 109b33795a..787d56c237 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -218,6 +218,10 @@ case "$FIRMWARE" in caldata_extract "caldata" 0x5000 0x2f20 ath10k_patch_mac $(mtd_get_mac_binary caldata 0xc) ;; + netgear,ex7300-v2) + caldata_extract "art" 0x5000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_binary artmtd 0xc) + ;; phicomm,k2t) caldata_extract "art" 0x5000 0x2f20 ath10k_patch_mac $(k2t_get_mac "5g_mac") diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index b3598a2000..3b23267b70 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -1580,6 +1580,23 @@ define Device/netgear_ex7300 endef TARGET_DEVICES += netgear_ex7300 +define Device/netgear_ex7300-v2 + $(Device/netgear_generic) + SOC := qcn5502 + DEVICE_MODEL := EX7300 + DEVICE_VARIANT := v2 + UIMAGE_MAGIC := 0x27051956 + NETGEAR_BOARD_ID := EX7300v2series + NETGEAR_HW_ID := 29765907+16+0+128 + IMAGE_SIZE := 14528k + IMAGE/default := append-kernel | pad-offset $$$$(BLOCKSIZE) 64 | \ + netgear-rootfs | pad-rootfs + IMAGE/sysupgrade.bin := $$(IMAGE/default) | check-size | append-metadata + IMAGE/factory.img := $$(IMAGE/default) | check-size | netgear-dni + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9984-ct +endef +TARGET_DEVICES += netgear_ex7300-v2 + define Device/netgear_wndr3x00 $(Device/netgear_generic) SOC := ar7161