From: Tianling Shen Date: Sun, 25 Jun 2023 16:37:30 +0000 (+0800) Subject: rockchip: add NanoPi R5S support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=c06a71f0b3fae00dbd402840ea6e3b532c35b0da;p=openwrt%2Fstaging%2Fthess.git rockchip: add NanoPi R5S support Hardware -------- RockChip RK3568 ARM64 (4 cores) 2GB or 4GB LPDDR4X RAM 1x 1000 Base-T 2x 2500 Base-T 4 LEDs (LAN1 / LAN2 / WAN / POWER) 8GB eMMC on-board Micro-SD Slot M.2 Slot 2x USB 3.0 Port Installation ------------ Uncompress the OpenWrt sysupgrade and write it to a micro SD card or internal eMMC using dd. Tested-by: Packet Please Signed-off-by: Tianling Shen --- diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds index d82e47cf53..cfab545849 100644 --- a/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds +++ b/target/linux/rockchip/armv8/base-files/etc/board.d/01_leds @@ -16,6 +16,11 @@ xunlong,orangepi-r1-plus-lts) ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0" ucidef_set_led_netdev "lan" "LAN" "green:lan" "eth1" ;; +friendlyarm,nanopi-r5s) + ucidef_set_led_netdev "wan" "WAN" "green:wan" "eth0" + ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "eth1" + ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "eth2" + ;; esac board_config_flush diff --git a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network index 7ac5148275..838a107193 100644 --- a/target/linux/rockchip/armv8/base-files/etc/board.d/02_network +++ b/target/linux/rockchip/armv8/base-files/etc/board.d/02_network @@ -14,6 +14,9 @@ rockchip_setup_interfaces() xunlong,orangepi-r1-plus-lts) ucidef_set_interfaces_lan_wan 'eth1' 'eth0' ;; + friendlyarm,nanopi-r5s) + ucidef_set_interfaces_lan_wan 'eth1 eth2' 'eth0' + ;; *) ucidef_set_interface_lan 'eth0' ;; @@ -58,6 +61,10 @@ rockchip_setup_macs() wan_mac=$(nanopi_r4s_get_mac wan) lan_mac=$(nanopi_r4s_get_mac lan) ;; + friendlyarm,nanopi-r5s) + wan_mac=$(macaddr_generate_from_mmc_cid mmcblk1) + lan_mac=$(macaddr_add "$wan_mac" 1) + ;; xunlong,orangepi-r1-plus|\ xunlong,orangepi-r1-plus-lts) wan_mac=$(macaddr_add "$(cat /sys/class/net/eth1/address)" -1) diff --git a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity index bb119b9185..161059a87b 100644 --- a/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity +++ b/target/linux/rockchip/armv8/base-files/etc/hotplug.d/net/40-net-smp-affinity @@ -40,5 +40,10 @@ friendlyarm,nanopi-r4s) set_interface_core 10 "eth0" set_interface_core 20 "eth1" ;; +friendlyarm,nanopi-r5s) + set_interface_core 2 "eth0" + set_interface_core 4 "eth1" + set_interface_core 8 "eth2" + ;; esac diff --git a/target/linux/rockchip/image/armv8.mk b/target/linux/rockchip/image/armv8.mk index 608ad79ca4..e836e3c91d 100644 --- a/target/linux/rockchip/image/armv8.mk +++ b/target/linux/rockchip/image/armv8.mk @@ -47,6 +47,14 @@ define Device/friendlyarm_nanopi-r4s endef TARGET_DEVICES += friendlyarm_nanopi-r4s +define Device/friendlyarm_nanopi-r5s + DEVICE_VENDOR := FriendlyARM + DEVICE_MODEL := NanoPi R5S + SOC := rk3568 + DEVICE_PACKAGES := kmod-r8169 +endef +TARGET_DEVICES += friendlyarm_nanopi-r5s + define Device/pine64_rock64 DEVICE_VENDOR := Pine64 DEVICE_MODEL := Rock64 diff --git a/target/linux/rockchip/patches-6.1/009-v6.4-arm64-dts-rockchip-Add-FriendlyElec-Nanopi-R5S.patch b/target/linux/rockchip/patches-6.1/009-v6.4-arm64-dts-rockchip-Add-FriendlyElec-Nanopi-R5S.patch new file mode 100644 index 0000000000..3d502a65b6 --- /dev/null +++ b/target/linux/rockchip/patches-6.1/009-v6.4-arm64-dts-rockchip-Add-FriendlyElec-Nanopi-R5S.patch @@ -0,0 +1,754 @@ +From c6629b9a6738a64507478527da6c7b83c10a6d2c Mon Sep 17 00:00:00 2001 +From: Vasily Khoruzhick +Date: Tue, 7 Mar 2023 22:32:40 -0800 +Subject: [PATCH] arm64: dts: rockchip: Add FriendlyElec Nanopi R5S + +FriendlyElec Nanopi R5S is an open-sourced mini IoT gateway device. + +Board Specifications +- Rockchip RK3568 +- 2 or 4GB LPDDR4X +- 8GB or 16GB eMMC, SD card slot +- GbE LAN (Native) +- 2x 2.5G LAN (PCIe) +- M.2 Connector +- HDMI 2.0, MIPI DSI/CSI +- 2xUSB 3.0 Host +- USB Type C PD, 5V/9V/12V +- GPIO: 12-pin 0.5mm FPC connector + +Based on Tianling Shen's work. + +Signed-off-by: Vasily Khoruzhick +Link: https://lore.kernel.org/r/20230308063240.107178-2-anarsoul@gmail.com +Signed-off-by: Heiko Stuebner +--- + arch/arm64/boot/dts/rockchip/Makefile | 1 + + .../boot/dts/rockchip/rk3568-nanopi-r5s.dts | 713 ++++++++++++++++++ + 2 files changed, 714 insertions(+) + create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts + +--- a/arch/arm64/boot/dts/rockchip/Makefile ++++ b/arch/arm64/boot/dts/rockchip/Makefile +@@ -74,4 +74,5 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-ro + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3566-soquartz-cm4.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-bpi-r2-pro.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-evb1-v10.dtb ++dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-nanopi-r5s.dtb + dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-rock-3a.dtb +--- /dev/null ++++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts +@@ -0,0 +1,713 @@ ++// SPDX-License-Identifier: GPL-2.0-or-later OR MIT ++/* ++ * Copyright (c) 2022 FriendlyElec Computer Tech. Co., Ltd. ++ * (http://www.friendlyelec.com) ++ * ++ * Copyright (c) 2023 Tianling Shen ++ */ ++ ++/dts-v1/; ++#include ++#include ++#include ++#include ++#include ++#include "rk3568.dtsi" ++ ++/ { ++ model = "FriendlyElec NanoPi R5S"; ++ compatible = "friendlyarm,nanopi-r5s", "rockchip,rk3568"; ++ ++ aliases { ++ ethernet0 = &gmac0; ++ mmc0 = &sdmmc0; ++ mmc1 = &sdhci; ++ }; ++ ++ chosen: chosen { ++ stdout-path = "serial2:1500000n8"; ++ }; ++ ++ hdmi-con { ++ compatible = "hdmi-connector"; ++ type = "a"; ++ ++ port { ++ hdmi_con_in: endpoint { ++ remote-endpoint = <&hdmi_out_con>; ++ }; ++ }; ++ }; ++ ++ gpio-leds { ++ compatible = "gpio-leds"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&lan1_led_pin>, <&lan2_led_pin>, <&power_led_pin>, <&wan_led_pin>; ++ ++ led-lan1 { ++ color = ; ++ function = LED_FUNCTION_LAN; ++ function-enumerator = <1>; ++ gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-lan2 { ++ color = ; ++ function = LED_FUNCTION_LAN; ++ function-enumerator = <2>; ++ gpios = <&gpio3 RK_PD7 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ power_led: led-power { ++ color = ; ++ function = LED_FUNCTION_POWER; ++ linux,default-trigger = "heartbeat"; ++ gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; ++ }; ++ ++ led-wan { ++ color = ; ++ function = LED_FUNCTION_WAN; ++ gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>; ++ }; ++ }; ++ ++ vdd_usbc: vdd-usbc-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vdd_usbc"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ }; ++ ++ vcc3v3_sys: vcc3v3-sys-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v3_sys"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ vin-supply = <&vdd_usbc>; ++ }; ++ ++ vcc5v0_sys: vcc5v0-sys-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc5v0_sys"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vdd_usbc>; ++ }; ++ ++ vcc3v3_pcie: vcc3v3-pcie-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v3_pcie"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ enable-active-high; ++ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; ++ startup-delay-us = <200000>; ++ vin-supply = <&vcc5v0_sys>; ++ }; ++ ++ vcc5v0_usb: vcc5v0-usb-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc5v0_usb"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vdd_usbc>; ++ }; ++ ++ vcc5v0_usb_host: vcc5v0-usb-host-regulator { ++ compatible = "regulator-fixed"; ++ enable-active-high; ++ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&vcc5v0_usb_host_en>; ++ regulator-name = "vcc5v0_usb_host"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vcc5v0_usb>; ++ }; ++ ++ vcc5v0_usb_otg: vcc5v0-usb-otg-regulator { ++ compatible = "regulator-fixed"; ++ enable-active-high; ++ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&vcc5v0_usb_otg_en>; ++ regulator-name = "vcc5v0_usb_otg"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vcc5v0_usb>; ++ }; ++ ++ pcie30_avdd0v9: pcie30-avdd0v9-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "pcie30_avdd0v9"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <900000>; ++ regulator-max-microvolt = <900000>; ++ vin-supply = <&vcc3v3_sys>; ++ }; ++ ++ pcie30_avdd1v8: pcie30-avdd1v8-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "pcie30_avdd1v8"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ vin-supply = <&vcc3v3_sys>; ++ }; ++}; ++ ++&combphy0 { ++ status = "okay"; ++}; ++ ++&combphy1 { ++ status = "okay"; ++}; ++ ++&combphy2 { ++ status = "okay"; ++}; ++ ++&cpu0 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&cpu2 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&cpu3 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&gmac0 { ++ assigned-clocks = <&cru SCLK_GMAC0_RX_TX>, <&cru SCLK_GMAC0>; ++ assigned-clock-parents = <&cru SCLK_GMAC0_RGMII_SPEED>, <&cru CLK_MAC0_2TOP>; ++ assigned-clock-rates = <0>, <125000000>; ++ clock_in_out = "output"; ++ phy-handle = <&rgmii_phy0>; ++ phy-mode = "rgmii-id"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&gmac0_miim ++ &gmac0_tx_bus2 ++ &gmac0_rx_bus2 ++ &gmac0_rgmii_clk ++ &gmac0_rgmii_bus>; ++ snps,reset-gpio = <&gpio0 RK_PC5 GPIO_ACTIVE_LOW>; ++ snps,reset-active-low; ++ /* Reset time is 15ms, 50ms for rtl8211f */ ++ snps,reset-delays-us = <0 15000 50000>; ++ tx_delay = <0x3c>; ++ rx_delay = <0x2f>; ++ status = "okay"; ++}; ++ ++&gpu { ++ mali-supply = <&vdd_gpu>; ++ status = "okay"; ++}; ++ ++&hdmi { ++ avdd-0v9-supply = <&vdda0v9_image>; ++ avdd-1v8-supply = <&vcca1v8_image>; ++ status = "okay"; ++}; ++ ++&hdmi_in { ++ hdmi_in_vp0: endpoint { ++ remote-endpoint = <&vp0_out_hdmi>; ++ }; ++}; ++ ++&hdmi_out { ++ hdmi_out_con: endpoint { ++ remote-endpoint = <&hdmi_con_in>; ++ }; ++}; ++ ++&hdmi_sound { ++ status = "okay"; ++}; ++ ++&i2c0 { ++ status = "okay"; ++ ++ vdd_cpu: regulator@1c { ++ compatible = "tcs,tcs4525"; ++ reg = <0x1c>; ++ fcs,suspend-voltage-selector = <1>; ++ regulator-name = "vdd_cpu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <800000>; ++ regulator-max-microvolt = <1150000>; ++ regulator-ramp-delay = <2300>; ++ vin-supply = <&vcc5v0_sys>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ rk809: pmic@20 { ++ compatible = "rockchip,rk809"; ++ reg = <0x20>; ++ interrupt-parent = <&gpio0>; ++ interrupts = ; ++ #clock-cells = <1>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pmic_int>; ++ rockchip,system-power-controller; ++ vcc1-supply = <&vcc3v3_sys>; ++ vcc2-supply = <&vcc3v3_sys>; ++ vcc3-supply = <&vcc3v3_sys>; ++ vcc4-supply = <&vcc3v3_sys>; ++ vcc5-supply = <&vcc3v3_sys>; ++ vcc6-supply = <&vcc3v3_sys>; ++ vcc7-supply = <&vcc3v3_sys>; ++ vcc8-supply = <&vcc3v3_sys>; ++ vcc9-supply = <&vcc3v3_sys>; ++ wakeup-source; ++ ++ regulators { ++ vdd_logic: DCDC_REG1 { ++ regulator-name = "vdd_logic"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-init-microvolt = <900000>; ++ regulator-initial-mode = <0x2>; ++ regulator-min-microvolt = <500000>; ++ regulator-max-microvolt = <1350000>; ++ regulator-ramp-delay = <6001>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdd_gpu: DCDC_REG2 { ++ regulator-name = "vdd_gpu"; ++ regulator-always-on; ++ regulator-init-microvolt = <900000>; ++ regulator-initial-mode = <0x2>; ++ regulator-min-microvolt = <500000>; ++ regulator-max-microvolt = <1350000>; ++ regulator-ramp-delay = <6001>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc_ddr: DCDC_REG3 { ++ regulator-name = "vcc_ddr"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-initial-mode = <0x2>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ }; ++ }; ++ ++ vdd_npu: DCDC_REG4 { ++ regulator-name = "vdd_npu"; ++ regulator-init-microvolt = <900000>; ++ regulator-initial-mode = <0x2>; ++ regulator-min-microvolt = <500000>; ++ regulator-max-microvolt = <1350000>; ++ regulator-ramp-delay = <6001>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc_1v8: DCDC_REG5 { ++ regulator-name = "vcc_1v8"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdda0v9_image: LDO_REG1 { ++ regulator-name = "vdda0v9_image"; ++ regulator-min-microvolt = <950000>; ++ regulator-max-microvolt = <950000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdda_0v9: LDO_REG2 { ++ regulator-name = "vdda_0v9"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <900000>; ++ regulator-max-microvolt = <900000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdda0v9_pmu: LDO_REG3 { ++ regulator-name = "vdda0v9_pmu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <900000>; ++ regulator-max-microvolt = <900000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <900000>; ++ }; ++ }; ++ ++ vccio_acodec: LDO_REG4 { ++ regulator-name = "vccio_acodec"; ++ regulator-always-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vccio_sd: LDO_REG5 { ++ regulator-name = "vccio_sd"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc3v3_pmu: LDO_REG6 { ++ regulator-name = "vcc3v3_pmu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <3300000>; ++ }; ++ }; ++ ++ vcca_1v8: LDO_REG7 { ++ regulator-name = "vcca_1v8"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcca1v8_pmu: LDO_REG8 { ++ regulator-name = "vcca1v8_pmu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1800000>; ++ }; ++ }; ++ ++ vcca1v8_image: LDO_REG9 { ++ regulator-name = "vcca1v8_image"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc_3v3: SWITCH_REG1 { ++ regulator-name = "vcc_3v3"; ++ regulator-always-on; ++ regulator-boot-on; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc3v3_sd: SWITCH_REG2 { ++ regulator-name = "vcc3v3_sd"; ++ regulator-always-on; ++ regulator-boot-on; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ }; ++ ++ }; ++}; ++ ++&i2c5 { ++ status = "okay"; ++ ++ hym8563: rtc@51 { ++ compatible = "haoyu,hym8563"; ++ reg = <0x51>; ++ interrupt-parent = <&gpio0>; ++ interrupts = ; ++ #clock-cells = <0>; ++ clock-output-names = "rtcic_32kout"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hym8563_int>; ++ wakeup-source; ++ }; ++}; ++ ++&i2s0_8ch { ++ status = "okay"; ++}; ++ ++&i2s1_8ch { ++ rockchip,trcm-sync-tx-only; ++ status = "okay"; ++}; ++ ++&mdio0 { ++ rgmii_phy0: ethernet-phy@1 { ++ compatible = "ethernet-phy-ieee802.3-c22"; ++ reg = <1>; ++ pinctrl-0 = <ð_phy0_reset_pin>; ++ pinctrl-names = "default"; ++ reset-assert-us = <10000>; ++ reset-deassert-us = <50000>; ++ reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>; ++ }; ++}; ++ ++&pcie2x1 { ++ num-lanes = <1>; ++ reset-gpios = <&gpio0 RK_PB6 GPIO_ACTIVE_HIGH>; ++ status = "okay"; ++}; ++ ++&pcie30phy { ++ data-lanes = <1 2>; ++ status = "okay"; ++}; ++ ++&pcie3x1 { ++ num-lanes = <1>; ++ reset-gpios = <&gpio0 RK_PA0 GPIO_ACTIVE_HIGH>; ++ vpcie3v3-supply = <&vcc3v3_pcie>; ++ status = "okay"; ++}; ++ ++&pcie3x2 { ++ num-lanes = <1>; ++ num-ib-windows = <8>; ++ num-ob-windows = <8>; ++ reset-gpios = <&gpio2 RK_PD6 GPIO_ACTIVE_HIGH>; ++ vpcie3v3-supply = <&vcc3v3_pcie>; ++ status = "okay"; ++}; ++ ++&pinctrl { ++ gmac0 { ++ eth_phy0_reset_pin: eth-phy0-reset-pin { ++ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>; ++ }; ++ }; ++ ++ gpio-leds { ++ lan1_led_pin: lan1-led-pin { ++ rockchip,pins = <3 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ lan2_led_pin: lan2-led-pin { ++ rockchip,pins = <3 RK_PD7 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ power_led_pin: power-led-pin { ++ rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ wan_led_pin: wan-led-pin { ++ rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ }; ++ ++ hym8563 { ++ hym8563_int: hym8563-int { ++ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>; ++ }; ++ }; ++ ++ pmic { ++ pmic_int: pmic-int { ++ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; ++ }; ++ }; ++ ++ usb { ++ vcc5v0_usb_host_en: vcc5v0-usb-host-en { ++ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ vcc5v0_usb_otg_en: vcc5v0-usb-otg-en { ++ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ }; ++}; ++ ++&pmu_io_domains { ++ pmuio1-supply = <&vcc3v3_pmu>; ++ pmuio2-supply = <&vcc3v3_pmu>; ++ vccio1-supply = <&vccio_acodec>; ++ vccio3-supply = <&vccio_sd>; ++ vccio4-supply = <&vcc_1v8>; ++ vccio5-supply = <&vcc_3v3>; ++ vccio6-supply = <&vcc_1v8>; ++ vccio7-supply = <&vcc_3v3>; ++ status = "okay"; ++}; ++ ++&saradc { ++ vref-supply = <&vcca_1v8>; ++ status = "okay"; ++}; ++ ++&sdhci { ++ bus-width = <8>; ++ max-frequency = <200000000>; ++ non-removable; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>; ++ status = "okay"; ++}; ++ ++&sdmmc0 { ++ max-frequency = <150000000>; ++ no-sdio; ++ no-mmc; ++ bus-width = <4>; ++ cap-mmc-highspeed; ++ cap-sd-highspeed; ++ disable-wp; ++ vmmc-supply = <&vcc3v3_sd>; ++ vqmmc-supply = <&vccio_sd>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>; ++ status = "okay"; ++}; ++ ++&tsadc { ++ rockchip,hw-tshut-mode = <1>; ++ rockchip,hw-tshut-polarity = <0>; ++ status = "okay"; ++}; ++ ++&uart2 { ++ status = "okay"; ++}; ++ ++&usb_host0_ehci { ++ status = "okay"; ++}; ++ ++&usb_host0_ohci { ++ status = "okay"; ++}; ++ ++&usb_host0_xhci { ++ extcon = <&usb2phy0>; ++ dr_mode = "host"; ++ status = "okay"; ++}; ++ ++&usb_host1_ehci { ++ status = "okay"; ++}; ++ ++&usb_host1_ohci { ++ status = "okay"; ++}; ++ ++&usb_host1_xhci { ++ status = "okay"; ++}; ++ ++&usb2phy0 { ++ status = "okay"; ++}; ++ ++&usb2phy0_host { ++ phy-supply = <&vcc5v0_usb_host>; ++ status = "okay"; ++}; ++ ++&usb2phy0_otg { ++ status = "okay"; ++}; ++ ++&usb2phy1 { ++ status = "okay"; ++}; ++ ++&usb2phy1_host { ++ phy-supply = <&vcc5v0_usb_otg>; ++ status = "okay"; ++}; ++ ++&usb2phy1_otg { ++ status = "okay"; ++}; ++ ++&vop { ++ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; ++ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; ++ status = "okay"; ++}; ++ ++&vop_mmu { ++ status = "okay"; ++}; ++ ++&vp0 { ++ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { ++ reg = ; ++ remote-endpoint = <&hdmi_in_vp0>; ++ }; ++}; diff --git a/target/linux/rockchip/patches-6.1/010-v6.4-arm64-dts-rockchip-create-common-dtsi-for-NanoPi-R5-serie.patch b/target/linux/rockchip/patches-6.1/010-v6.4-arm64-dts-rockchip-create-common-dtsi-for-NanoPi-R5-serie.patch new file mode 100644 index 0000000000..cf9fe06ad0 --- /dev/null +++ b/target/linux/rockchip/patches-6.1/010-v6.4-arm64-dts-rockchip-create-common-dtsi-for-NanoPi-R5-serie.patch @@ -0,0 +1,1226 @@ +From c8ec73b05a95d9f0969ae0f28dd8799a54fcdfc7 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Sat, 18 Mar 2023 16:37:41 +0800 +Subject: [PATCH] arm64: dts: rockchip: create common dtsi for NanoPi R5 series + +Create common dtsi for the FriendlyElec NanoPi R5 series. + +Signed-off-by: Tianling Shen +Link: https://lore.kernel.org/r/20230318083745.6181-2-cnsztl@gmail.com +Signed-off-by: Heiko Stuebner +--- + .../boot/dts/rockchip/rk3568-nanopi-r5s.dts | 575 +---------------- + .../boot/dts/rockchip/rk3568-nanopi-r5s.dtsi | 596 ++++++++++++++++++ + 2 files changed, 597 insertions(+), 574 deletions(-) + create mode 100644 arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi + +--- a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts ++++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts +@@ -7,12 +7,7 @@ + */ + + /dts-v1/; +-#include +-#include +-#include +-#include +-#include +-#include "rk3568.dtsi" ++#include "rk3568-nanopi-r5s.dtsi" + + / { + model = "FriendlyElec NanoPi R5S"; +@@ -20,23 +15,6 @@ + + aliases { + ethernet0 = &gmac0; +- mmc0 = &sdmmc0; +- mmc1 = &sdhci; +- }; +- +- chosen: chosen { +- stdout-path = "serial2:1500000n8"; +- }; +- +- hdmi-con { +- compatible = "hdmi-connector"; +- type = "a"; +- +- port { +- hdmi_con_in: endpoint { +- remote-endpoint = <&hdmi_out_con>; +- }; +- }; + }; + + gpio-leds { +@@ -71,130 +49,6 @@ + gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>; + }; + }; +- +- vdd_usbc: vdd-usbc-regulator { +- compatible = "regulator-fixed"; +- regulator-name = "vdd_usbc"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <5000000>; +- regulator-max-microvolt = <5000000>; +- }; +- +- vcc3v3_sys: vcc3v3-sys-regulator { +- compatible = "regulator-fixed"; +- regulator-name = "vcc3v3_sys"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <3300000>; +- regulator-max-microvolt = <3300000>; +- vin-supply = <&vdd_usbc>; +- }; +- +- vcc5v0_sys: vcc5v0-sys-regulator { +- compatible = "regulator-fixed"; +- regulator-name = "vcc5v0_sys"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <5000000>; +- regulator-max-microvolt = <5000000>; +- vin-supply = <&vdd_usbc>; +- }; +- +- vcc3v3_pcie: vcc3v3-pcie-regulator { +- compatible = "regulator-fixed"; +- regulator-name = "vcc3v3_pcie"; +- regulator-min-microvolt = <3300000>; +- regulator-max-microvolt = <3300000>; +- enable-active-high; +- gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; +- startup-delay-us = <200000>; +- vin-supply = <&vcc5v0_sys>; +- }; +- +- vcc5v0_usb: vcc5v0-usb-regulator { +- compatible = "regulator-fixed"; +- regulator-name = "vcc5v0_usb"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <5000000>; +- regulator-max-microvolt = <5000000>; +- vin-supply = <&vdd_usbc>; +- }; +- +- vcc5v0_usb_host: vcc5v0-usb-host-regulator { +- compatible = "regulator-fixed"; +- enable-active-high; +- gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>; +- pinctrl-names = "default"; +- pinctrl-0 = <&vcc5v0_usb_host_en>; +- regulator-name = "vcc5v0_usb_host"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <5000000>; +- regulator-max-microvolt = <5000000>; +- vin-supply = <&vcc5v0_usb>; +- }; +- +- vcc5v0_usb_otg: vcc5v0-usb-otg-regulator { +- compatible = "regulator-fixed"; +- enable-active-high; +- gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>; +- pinctrl-names = "default"; +- pinctrl-0 = <&vcc5v0_usb_otg_en>; +- regulator-name = "vcc5v0_usb_otg"; +- regulator-min-microvolt = <5000000>; +- regulator-max-microvolt = <5000000>; +- vin-supply = <&vcc5v0_usb>; +- }; +- +- pcie30_avdd0v9: pcie30-avdd0v9-regulator { +- compatible = "regulator-fixed"; +- regulator-name = "pcie30_avdd0v9"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <900000>; +- regulator-max-microvolt = <900000>; +- vin-supply = <&vcc3v3_sys>; +- }; +- +- pcie30_avdd1v8: pcie30-avdd1v8-regulator { +- compatible = "regulator-fixed"; +- regulator-name = "pcie30_avdd1v8"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- vin-supply = <&vcc3v3_sys>; +- }; +-}; +- +-&combphy0 { +- status = "okay"; +-}; +- +-&combphy1 { +- status = "okay"; +-}; +- +-&combphy2 { +- status = "okay"; +-}; +- +-&cpu0 { +- cpu-supply = <&vdd_cpu>; +-}; +- +-&cpu1 { +- cpu-supply = <&vdd_cpu>; +-}; +- +-&cpu2 { +- cpu-supply = <&vdd_cpu>; +-}; +- +-&cpu3 { +- cpu-supply = <&vdd_cpu>; + }; + + &gmac0 { +@@ -219,292 +73,6 @@ + status = "okay"; + }; + +-&gpu { +- mali-supply = <&vdd_gpu>; +- status = "okay"; +-}; +- +-&hdmi { +- avdd-0v9-supply = <&vdda0v9_image>; +- avdd-1v8-supply = <&vcca1v8_image>; +- status = "okay"; +-}; +- +-&hdmi_in { +- hdmi_in_vp0: endpoint { +- remote-endpoint = <&vp0_out_hdmi>; +- }; +-}; +- +-&hdmi_out { +- hdmi_out_con: endpoint { +- remote-endpoint = <&hdmi_con_in>; +- }; +-}; +- +-&hdmi_sound { +- status = "okay"; +-}; +- +-&i2c0 { +- status = "okay"; +- +- vdd_cpu: regulator@1c { +- compatible = "tcs,tcs4525"; +- reg = <0x1c>; +- fcs,suspend-voltage-selector = <1>; +- regulator-name = "vdd_cpu"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <800000>; +- regulator-max-microvolt = <1150000>; +- regulator-ramp-delay = <2300>; +- vin-supply = <&vcc5v0_sys>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- rk809: pmic@20 { +- compatible = "rockchip,rk809"; +- reg = <0x20>; +- interrupt-parent = <&gpio0>; +- interrupts = ; +- #clock-cells = <1>; +- pinctrl-names = "default"; +- pinctrl-0 = <&pmic_int>; +- rockchip,system-power-controller; +- vcc1-supply = <&vcc3v3_sys>; +- vcc2-supply = <&vcc3v3_sys>; +- vcc3-supply = <&vcc3v3_sys>; +- vcc4-supply = <&vcc3v3_sys>; +- vcc5-supply = <&vcc3v3_sys>; +- vcc6-supply = <&vcc3v3_sys>; +- vcc7-supply = <&vcc3v3_sys>; +- vcc8-supply = <&vcc3v3_sys>; +- vcc9-supply = <&vcc3v3_sys>; +- wakeup-source; +- +- regulators { +- vdd_logic: DCDC_REG1 { +- regulator-name = "vdd_logic"; +- regulator-always-on; +- regulator-boot-on; +- regulator-init-microvolt = <900000>; +- regulator-initial-mode = <0x2>; +- regulator-min-microvolt = <500000>; +- regulator-max-microvolt = <1350000>; +- regulator-ramp-delay = <6001>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vdd_gpu: DCDC_REG2 { +- regulator-name = "vdd_gpu"; +- regulator-always-on; +- regulator-init-microvolt = <900000>; +- regulator-initial-mode = <0x2>; +- regulator-min-microvolt = <500000>; +- regulator-max-microvolt = <1350000>; +- regulator-ramp-delay = <6001>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vcc_ddr: DCDC_REG3 { +- regulator-name = "vcc_ddr"; +- regulator-always-on; +- regulator-boot-on; +- regulator-initial-mode = <0x2>; +- +- regulator-state-mem { +- regulator-on-in-suspend; +- }; +- }; +- +- vdd_npu: DCDC_REG4 { +- regulator-name = "vdd_npu"; +- regulator-init-microvolt = <900000>; +- regulator-initial-mode = <0x2>; +- regulator-min-microvolt = <500000>; +- regulator-max-microvolt = <1350000>; +- regulator-ramp-delay = <6001>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vcc_1v8: DCDC_REG5 { +- regulator-name = "vcc_1v8"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vdda0v9_image: LDO_REG1 { +- regulator-name = "vdda0v9_image"; +- regulator-min-microvolt = <950000>; +- regulator-max-microvolt = <950000>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vdda_0v9: LDO_REG2 { +- regulator-name = "vdda_0v9"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <900000>; +- regulator-max-microvolt = <900000>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vdda0v9_pmu: LDO_REG3 { +- regulator-name = "vdda0v9_pmu"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <900000>; +- regulator-max-microvolt = <900000>; +- +- regulator-state-mem { +- regulator-on-in-suspend; +- regulator-suspend-microvolt = <900000>; +- }; +- }; +- +- vccio_acodec: LDO_REG4 { +- regulator-name = "vccio_acodec"; +- regulator-always-on; +- regulator-min-microvolt = <3300000>; +- regulator-max-microvolt = <3300000>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vccio_sd: LDO_REG5 { +- regulator-name = "vccio_sd"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <3300000>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vcc3v3_pmu: LDO_REG6 { +- regulator-name = "vcc3v3_pmu"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <3300000>; +- regulator-max-microvolt = <3300000>; +- +- regulator-state-mem { +- regulator-on-in-suspend; +- regulator-suspend-microvolt = <3300000>; +- }; +- }; +- +- vcca_1v8: LDO_REG7 { +- regulator-name = "vcca_1v8"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vcca1v8_pmu: LDO_REG8 { +- regulator-name = "vcca1v8_pmu"; +- regulator-always-on; +- regulator-boot-on; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- +- regulator-state-mem { +- regulator-on-in-suspend; +- regulator-suspend-microvolt = <1800000>; +- }; +- }; +- +- vcca1v8_image: LDO_REG9 { +- regulator-name = "vcca1v8_image"; +- regulator-min-microvolt = <1800000>; +- regulator-max-microvolt = <1800000>; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vcc_3v3: SWITCH_REG1 { +- regulator-name = "vcc_3v3"; +- regulator-always-on; +- regulator-boot-on; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- +- vcc3v3_sd: SWITCH_REG2 { +- regulator-name = "vcc3v3_sd"; +- regulator-always-on; +- regulator-boot-on; +- +- regulator-state-mem { +- regulator-off-in-suspend; +- }; +- }; +- }; +- +- }; +-}; +- +-&i2c5 { +- status = "okay"; +- +- hym8563: rtc@51 { +- compatible = "haoyu,hym8563"; +- reg = <0x51>; +- interrupt-parent = <&gpio0>; +- interrupts = ; +- #clock-cells = <0>; +- clock-output-names = "rtcic_32kout"; +- pinctrl-names = "default"; +- pinctrl-0 = <&hym8563_int>; +- wakeup-source; +- }; +-}; +- +-&i2s0_8ch { +- status = "okay"; +-}; +- +-&i2s1_8ch { +- rockchip,trcm-sync-tx-only; +- status = "okay"; +-}; +- + &mdio0 { + rgmii_phy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; +@@ -568,146 +136,5 @@ + rockchip,pins = <2 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>; + }; + }; +- +- hym8563 { +- hym8563_int: hym8563-int { +- rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>; +- }; +- }; +- +- pmic { +- pmic_int: pmic-int { +- rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; +- }; +- }; +- +- usb { +- vcc5v0_usb_host_en: vcc5v0-usb-host-en { +- rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; +- }; +- +- vcc5v0_usb_otg_en: vcc5v0-usb-otg-en { +- rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; +- }; +- }; +-}; +- +-&pmu_io_domains { +- pmuio1-supply = <&vcc3v3_pmu>; +- pmuio2-supply = <&vcc3v3_pmu>; +- vccio1-supply = <&vccio_acodec>; +- vccio3-supply = <&vccio_sd>; +- vccio4-supply = <&vcc_1v8>; +- vccio5-supply = <&vcc_3v3>; +- vccio6-supply = <&vcc_1v8>; +- vccio7-supply = <&vcc_3v3>; +- status = "okay"; +-}; +- +-&saradc { +- vref-supply = <&vcca_1v8>; +- status = "okay"; +-}; +- +-&sdhci { +- bus-width = <8>; +- max-frequency = <200000000>; +- non-removable; +- pinctrl-names = "default"; +- pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>; +- status = "okay"; +-}; +- +-&sdmmc0 { +- max-frequency = <150000000>; +- no-sdio; +- no-mmc; +- bus-width = <4>; +- cap-mmc-highspeed; +- cap-sd-highspeed; +- disable-wp; +- vmmc-supply = <&vcc3v3_sd>; +- vqmmc-supply = <&vccio_sd>; +- pinctrl-names = "default"; +- pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>; +- status = "okay"; +-}; +- +-&tsadc { +- rockchip,hw-tshut-mode = <1>; +- rockchip,hw-tshut-polarity = <0>; +- status = "okay"; +-}; +- +-&uart2 { +- status = "okay"; +-}; +- +-&usb_host0_ehci { +- status = "okay"; +-}; +- +-&usb_host0_ohci { +- status = "okay"; +-}; +- +-&usb_host0_xhci { +- extcon = <&usb2phy0>; +- dr_mode = "host"; +- status = "okay"; +-}; +- +-&usb_host1_ehci { +- status = "okay"; +-}; +- +-&usb_host1_ohci { +- status = "okay"; + }; + +-&usb_host1_xhci { +- status = "okay"; +-}; +- +-&usb2phy0 { +- status = "okay"; +-}; +- +-&usb2phy0_host { +- phy-supply = <&vcc5v0_usb_host>; +- status = "okay"; +-}; +- +-&usb2phy0_otg { +- status = "okay"; +-}; +- +-&usb2phy1 { +- status = "okay"; +-}; +- +-&usb2phy1_host { +- phy-supply = <&vcc5v0_usb_otg>; +- status = "okay"; +-}; +- +-&usb2phy1_otg { +- status = "okay"; +-}; +- +-&vop { +- assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; +- assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; +- status = "okay"; +-}; +- +-&vop_mmu { +- status = "okay"; +-}; +- +-&vp0 { +- vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { +- reg = ; +- remote-endpoint = <&hdmi_in_vp0>; +- }; +-}; +--- /dev/null ++++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi +@@ -0,0 +1,596 @@ ++// SPDX-License-Identifier: GPL-2.0-or-later OR MIT ++/* ++ * Copyright (c) 2022 FriendlyElec Computer Tech. Co., Ltd. ++ * (http://www.friendlyelec.com) ++ * ++ * Copyright (c) 2023 Tianling Shen ++ */ ++ ++/dts-v1/; ++#include ++#include ++#include ++#include ++#include ++#include "rk3568.dtsi" ++ ++/ { ++ aliases { ++ mmc0 = &sdmmc0; ++ mmc1 = &sdhci; ++ }; ++ ++ chosen: chosen { ++ stdout-path = "serial2:1500000n8"; ++ }; ++ ++ hdmi-con { ++ compatible = "hdmi-connector"; ++ type = "a"; ++ ++ port { ++ hdmi_con_in: endpoint { ++ remote-endpoint = <&hdmi_out_con>; ++ }; ++ }; ++ }; ++ ++ vdd_usbc: vdd-usbc-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vdd_usbc"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ }; ++ ++ vcc3v3_sys: vcc3v3-sys-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v3_sys"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ vin-supply = <&vdd_usbc>; ++ }; ++ ++ vcc5v0_sys: vcc5v0-sys-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc5v0_sys"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vdd_usbc>; ++ }; ++ ++ vcc3v3_pcie: vcc3v3-pcie-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc3v3_pcie"; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ enable-active-high; ++ gpios = <&gpio0 RK_PD4 GPIO_ACTIVE_HIGH>; ++ startup-delay-us = <200000>; ++ vin-supply = <&vcc5v0_sys>; ++ }; ++ ++ vcc5v0_usb: vcc5v0-usb-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "vcc5v0_usb"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vdd_usbc>; ++ }; ++ ++ vcc5v0_usb_host: vcc5v0-usb-host-regulator { ++ compatible = "regulator-fixed"; ++ enable-active-high; ++ gpio = <&gpio0 RK_PA6 GPIO_ACTIVE_HIGH>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&vcc5v0_usb_host_en>; ++ regulator-name = "vcc5v0_usb_host"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vcc5v0_usb>; ++ }; ++ ++ vcc5v0_usb_otg: vcc5v0-usb-otg-regulator { ++ compatible = "regulator-fixed"; ++ enable-active-high; ++ gpio = <&gpio0 RK_PA5 GPIO_ACTIVE_HIGH>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&vcc5v0_usb_otg_en>; ++ regulator-name = "vcc5v0_usb_otg"; ++ regulator-min-microvolt = <5000000>; ++ regulator-max-microvolt = <5000000>; ++ vin-supply = <&vcc5v0_usb>; ++ }; ++ ++ pcie30_avdd0v9: pcie30-avdd0v9-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "pcie30_avdd0v9"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <900000>; ++ regulator-max-microvolt = <900000>; ++ vin-supply = <&vcc3v3_sys>; ++ }; ++ ++ pcie30_avdd1v8: pcie30-avdd1v8-regulator { ++ compatible = "regulator-fixed"; ++ regulator-name = "pcie30_avdd1v8"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ vin-supply = <&vcc3v3_sys>; ++ }; ++}; ++ ++&combphy0 { ++ status = "okay"; ++}; ++ ++&combphy1 { ++ status = "okay"; ++}; ++ ++&combphy2 { ++ status = "okay"; ++}; ++ ++&cpu0 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&cpu1 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&cpu2 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&cpu3 { ++ cpu-supply = <&vdd_cpu>; ++}; ++ ++&gpu { ++ mali-supply = <&vdd_gpu>; ++ status = "okay"; ++}; ++ ++&hdmi { ++ avdd-0v9-supply = <&vdda0v9_image>; ++ avdd-1v8-supply = <&vcca1v8_image>; ++ status = "okay"; ++}; ++ ++&hdmi_in { ++ hdmi_in_vp0: endpoint { ++ remote-endpoint = <&vp0_out_hdmi>; ++ }; ++}; ++ ++&hdmi_out { ++ hdmi_out_con: endpoint { ++ remote-endpoint = <&hdmi_con_in>; ++ }; ++}; ++ ++&hdmi_sound { ++ status = "okay"; ++}; ++ ++&i2c0 { ++ status = "okay"; ++ ++ vdd_cpu: regulator@1c { ++ compatible = "tcs,tcs4525"; ++ reg = <0x1c>; ++ fcs,suspend-voltage-selector = <1>; ++ regulator-name = "vdd_cpu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <800000>; ++ regulator-max-microvolt = <1150000>; ++ regulator-ramp-delay = <2300>; ++ vin-supply = <&vcc5v0_sys>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ rk809: pmic@20 { ++ compatible = "rockchip,rk809"; ++ reg = <0x20>; ++ interrupt-parent = <&gpio0>; ++ interrupts = ; ++ #clock-cells = <1>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&pmic_int>; ++ rockchip,system-power-controller; ++ vcc1-supply = <&vcc3v3_sys>; ++ vcc2-supply = <&vcc3v3_sys>; ++ vcc3-supply = <&vcc3v3_sys>; ++ vcc4-supply = <&vcc3v3_sys>; ++ vcc5-supply = <&vcc3v3_sys>; ++ vcc6-supply = <&vcc3v3_sys>; ++ vcc7-supply = <&vcc3v3_sys>; ++ vcc8-supply = <&vcc3v3_sys>; ++ vcc9-supply = <&vcc3v3_sys>; ++ wakeup-source; ++ ++ regulators { ++ vdd_logic: DCDC_REG1 { ++ regulator-name = "vdd_logic"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-init-microvolt = <900000>; ++ regulator-initial-mode = <0x2>; ++ regulator-min-microvolt = <500000>; ++ regulator-max-microvolt = <1350000>; ++ regulator-ramp-delay = <6001>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdd_gpu: DCDC_REG2 { ++ regulator-name = "vdd_gpu"; ++ regulator-always-on; ++ regulator-init-microvolt = <900000>; ++ regulator-initial-mode = <0x2>; ++ regulator-min-microvolt = <500000>; ++ regulator-max-microvolt = <1350000>; ++ regulator-ramp-delay = <6001>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc_ddr: DCDC_REG3 { ++ regulator-name = "vcc_ddr"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-initial-mode = <0x2>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ }; ++ }; ++ ++ vdd_npu: DCDC_REG4 { ++ regulator-name = "vdd_npu"; ++ regulator-init-microvolt = <900000>; ++ regulator-initial-mode = <0x2>; ++ regulator-min-microvolt = <500000>; ++ regulator-max-microvolt = <1350000>; ++ regulator-ramp-delay = <6001>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc_1v8: DCDC_REG5 { ++ regulator-name = "vcc_1v8"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdda0v9_image: LDO_REG1 { ++ regulator-name = "vdda0v9_image"; ++ regulator-min-microvolt = <950000>; ++ regulator-max-microvolt = <950000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdda_0v9: LDO_REG2 { ++ regulator-name = "vdda_0v9"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <900000>; ++ regulator-max-microvolt = <900000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vdda0v9_pmu: LDO_REG3 { ++ regulator-name = "vdda0v9_pmu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <900000>; ++ regulator-max-microvolt = <900000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <900000>; ++ }; ++ }; ++ ++ vccio_acodec: LDO_REG4 { ++ regulator-name = "vccio_acodec"; ++ regulator-always-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vccio_sd: LDO_REG5 { ++ regulator-name = "vccio_sd"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc3v3_pmu: LDO_REG6 { ++ regulator-name = "vcc3v3_pmu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <3300000>; ++ regulator-max-microvolt = <3300000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <3300000>; ++ }; ++ }; ++ ++ vcca_1v8: LDO_REG7 { ++ regulator-name = "vcca_1v8"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcca1v8_pmu: LDO_REG8 { ++ regulator-name = "vcca1v8_pmu"; ++ regulator-always-on; ++ regulator-boot-on; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-on-in-suspend; ++ regulator-suspend-microvolt = <1800000>; ++ }; ++ }; ++ ++ vcca1v8_image: LDO_REG9 { ++ regulator-name = "vcca1v8_image"; ++ regulator-min-microvolt = <1800000>; ++ regulator-max-microvolt = <1800000>; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc_3v3: SWITCH_REG1 { ++ regulator-name = "vcc_3v3"; ++ regulator-always-on; ++ regulator-boot-on; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ ++ vcc3v3_sd: SWITCH_REG2 { ++ regulator-name = "vcc3v3_sd"; ++ regulator-always-on; ++ regulator-boot-on; ++ ++ regulator-state-mem { ++ regulator-off-in-suspend; ++ }; ++ }; ++ }; ++ ++ }; ++}; ++ ++&i2c5 { ++ status = "okay"; ++ ++ hym8563: rtc@51 { ++ compatible = "haoyu,hym8563"; ++ reg = <0x51>; ++ interrupt-parent = <&gpio0>; ++ interrupts = ; ++ #clock-cells = <0>; ++ clock-output-names = "rtcic_32kout"; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&hym8563_int>; ++ wakeup-source; ++ }; ++}; ++ ++&i2s0_8ch { ++ status = "okay"; ++}; ++ ++&i2s1_8ch { ++ rockchip,trcm-sync-tx-only; ++ status = "okay"; ++}; ++ ++&pcie30phy { ++ data-lanes = <1 2>; ++ status = "okay"; ++}; ++ ++&pinctrl { ++ hym8563 { ++ hym8563_int: hym8563-int { ++ rockchip,pins = <0 RK_PD3 RK_FUNC_GPIO &pcfg_pull_up>; ++ }; ++ }; ++ ++ pmic { ++ pmic_int: pmic-int { ++ rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; ++ }; ++ }; ++ ++ usb { ++ vcc5v0_usb_host_en: vcc5v0-usb-host-en { ++ rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ ++ vcc5v0_usb_otg_en: vcc5v0-usb-otg-en { ++ rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; ++ }; ++ }; ++}; ++ ++&pmu_io_domains { ++ pmuio1-supply = <&vcc3v3_pmu>; ++ pmuio2-supply = <&vcc3v3_pmu>; ++ vccio1-supply = <&vccio_acodec>; ++ vccio3-supply = <&vccio_sd>; ++ vccio4-supply = <&vcc_1v8>; ++ vccio5-supply = <&vcc_3v3>; ++ vccio6-supply = <&vcc_1v8>; ++ vccio7-supply = <&vcc_3v3>; ++ status = "okay"; ++}; ++ ++&saradc { ++ vref-supply = <&vcca_1v8>; ++ status = "okay"; ++}; ++ ++&sdhci { ++ bus-width = <8>; ++ max-frequency = <200000000>; ++ non-removable; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&emmc_bus8 &emmc_clk &emmc_cmd>; ++ status = "okay"; ++}; ++ ++&sdmmc0 { ++ max-frequency = <150000000>; ++ no-sdio; ++ no-mmc; ++ bus-width = <4>; ++ cap-mmc-highspeed; ++ cap-sd-highspeed; ++ disable-wp; ++ vmmc-supply = <&vcc3v3_sd>; ++ vqmmc-supply = <&vccio_sd>; ++ pinctrl-names = "default"; ++ pinctrl-0 = <&sdmmc0_bus4 &sdmmc0_clk &sdmmc0_cmd &sdmmc0_det>; ++ status = "okay"; ++}; ++ ++&tsadc { ++ rockchip,hw-tshut-mode = <1>; ++ rockchip,hw-tshut-polarity = <0>; ++ status = "okay"; ++}; ++ ++&uart2 { ++ status = "okay"; ++}; ++ ++&usb_host0_ehci { ++ status = "okay"; ++}; ++ ++&usb_host0_ohci { ++ status = "okay"; ++}; ++ ++&usb_host0_xhci { ++ extcon = <&usb2phy0>; ++ dr_mode = "host"; ++ status = "okay"; ++}; ++ ++&usb_host1_ehci { ++ status = "okay"; ++}; ++ ++&usb_host1_ohci { ++ status = "okay"; ++}; ++ ++&usb_host1_xhci { ++ status = "okay"; ++}; ++ ++&usb2phy0 { ++ status = "okay"; ++}; ++ ++&usb2phy0_host { ++ phy-supply = <&vcc5v0_usb_host>; ++ status = "okay"; ++}; ++ ++&usb2phy0_otg { ++ status = "okay"; ++}; ++ ++&usb2phy1 { ++ status = "okay"; ++}; ++ ++&usb2phy1_host { ++ phy-supply = <&vcc5v0_usb_otg>; ++ status = "okay"; ++}; ++ ++&usb2phy1_otg { ++ status = "okay"; ++}; ++ ++&vop { ++ assigned-clocks = <&cru DCLK_VOP0>, <&cru DCLK_VOP1>; ++ assigned-clock-parents = <&pmucru PLL_HPLL>, <&cru PLL_VPLL>; ++ status = "okay"; ++}; ++ ++&vop_mmu { ++ status = "okay"; ++}; ++ ++&vp0 { ++ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 { ++ reg = ; ++ remote-endpoint = <&hdmi_in_vp0>; ++ }; ++}; diff --git a/target/linux/rockchip/patches-6.1/011-v6.4-arm64-dts-rockchip-fix-gmac-support-for-NanoPi-R5S.patch b/target/linux/rockchip/patches-6.1/011-v6.4-arm64-dts-rockchip-fix-gmac-support-for-NanoPi-R5S.patch new file mode 100644 index 0000000000..47f76d54e7 --- /dev/null +++ b/target/linux/rockchip/patches-6.1/011-v6.4-arm64-dts-rockchip-fix-gmac-support-for-NanoPi-R5S.patch @@ -0,0 +1,49 @@ +From 31425b1fadb2040b359e52ffc24c049a78d56c96 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Sat, 18 Mar 2023 16:37:44 +0800 +Subject: [PATCH] arm64: dts: rockchip: fix gmac support for NanoPi R5S + +- Changed phy-mode to rgmii. + +- Fixed pull type in pinctrl for gmac0. + +- Removed duplicate properties in mdio node. + These properties are defined in the gmac0 node already. + +Signed-off-by: Tianling Shen +Link: https://lore.kernel.org/r/20230318083745.6181-5-cnsztl@gmail.com +Signed-off-by: Heiko Stuebner +--- + arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts | 7 ++----- + 1 file changed, 2 insertions(+), 5 deletions(-) + +--- a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts ++++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts +@@ -57,7 +57,7 @@ + assigned-clock-rates = <0>, <125000000>; + clock_in_out = "output"; + phy-handle = <&rgmii_phy0>; +- phy-mode = "rgmii-id"; ++ phy-mode = "rgmii"; + pinctrl-names = "default"; + pinctrl-0 = <&gmac0_miim + &gmac0_tx_bus2 +@@ -79,9 +79,6 @@ + reg = <1>; + pinctrl-0 = <ð_phy0_reset_pin>; + pinctrl-names = "default"; +- reset-assert-us = <10000>; +- reset-deassert-us = <50000>; +- reset-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_LOW>; + }; + }; + +@@ -115,7 +112,7 @@ + &pinctrl { + gmac0 { + eth_phy0_reset_pin: eth-phy0-reset-pin { +- rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_down>; ++ rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_up>; + }; + }; + diff --git a/target/linux/rockchip/patches-6.1/012-v6.4-arm64-dts-rockchip-remove-I2S1-TDM-node-for-the-NanoPi-R5.patch b/target/linux/rockchip/patches-6.1/012-v6.4-arm64-dts-rockchip-remove-I2S1-TDM-node-for-the-NanoPi-R5.patch new file mode 100644 index 0000000000..48021b226a --- /dev/null +++ b/target/linux/rockchip/patches-6.1/012-v6.4-arm64-dts-rockchip-remove-I2S1-TDM-node-for-the-NanoPi-R5.patch @@ -0,0 +1,39 @@ +From 975e9bbad11950fc8276f1fa260d8bf2c341aa41 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Sat, 18 Mar 2023 16:37:45 +0800 +Subject: [PATCH] arm64: dts: rockchip: remove I2S1 TDM node for the NanoPi R5 + series + +This is for the audio output which does not exist on the boards. +Also disable regulator-always-on for vccio_acodec since it's only +used by the audio output. + +Signed-off-by: Tianling Shen +Link: https://lore.kernel.org/r/20230318083745.6181-6-cnsztl@gmail.com +Signed-off-by: Heiko Stuebner +--- + arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi | 6 ------ + 1 file changed, 6 deletions(-) + +--- a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi ++++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi +@@ -330,7 +330,6 @@ + + vccio_acodec: LDO_REG4 { + regulator-name = "vccio_acodec"; +- regulator-always-on; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + +@@ -441,11 +440,6 @@ + status = "okay"; + }; + +-&i2s1_8ch { +- rockchip,trcm-sync-tx-only; +- status = "okay"; +-}; +- + &pcie30phy { + data-lanes = <1 2>; + status = "okay"; diff --git a/target/linux/rockchip/patches-6.1/110-arm64-dts-rockchip-Update-LED-properties-for-NanoPi-.patch b/target/linux/rockchip/patches-6.1/110-arm64-dts-rockchip-Update-LED-properties-for-NanoPi-.patch new file mode 100644 index 0000000000..8339ef5dbc --- /dev/null +++ b/target/linux/rockchip/patches-6.1/110-arm64-dts-rockchip-Update-LED-properties-for-NanoPi-.patch @@ -0,0 +1,63 @@ +From 0000000000000000000000000000000000000000 Mon Sep 17 00:00:00 2001 +From: Tianling Shen +Date: Tue Jun 20 16:45:27 2023 +0800 +Subject: [PATCH] arm64: dts: rockchip: Update LED properties for NanoPi R5 + series + +Add OpenWrt's LED aliases for showing system status. +Also replace function/color with legacy label as OpenWrt relys on it +to update LED settings. + +Signed-off-by: Tianling Shen +--- + +--- a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts ++++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dts +@@ -23,29 +23,22 @@ + pinctrl-0 = <&lan1_led_pin>, <&lan2_led_pin>, <&power_led_pin>, <&wan_led_pin>; + + led-lan1 { +- color = ; +- function = LED_FUNCTION_LAN; +- function-enumerator = <1>; ++ label = "green:lan1"; + gpios = <&gpio3 RK_PD6 GPIO_ACTIVE_HIGH>; + }; + + led-lan2 { +- color = ; +- function = LED_FUNCTION_LAN; +- function-enumerator = <2>; ++ label = "green:lan2"; + gpios = <&gpio3 RK_PD7 GPIO_ACTIVE_HIGH>; + }; + + power_led: led-power { +- color = ; +- function = LED_FUNCTION_POWER; +- linux,default-trigger = "heartbeat"; ++ label = "red:power"; + gpios = <&gpio4 RK_PD2 GPIO_ACTIVE_HIGH>; + }; + + led-wan { +- color = ; +- function = LED_FUNCTION_WAN; ++ label = "green:wan"; + gpios = <&gpio2 RK_PC1 GPIO_ACTIVE_HIGH>; + }; + }; +--- a/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi ++++ b/arch/arm64/boot/dts/rockchip/rk3568-nanopi-r5s.dtsi +@@ -18,6 +18,11 @@ + aliases { + mmc0 = &sdmmc0; + mmc1 = &sdhci; ++ ++ led-boot = &power_led; ++ led-failsafe = &power_led; ++ led-running = &power_led; ++ led-upgrade = &power_led; + }; + + chosen: chosen {