From: Dirk Buchwalder Date: Sat, 1 Jan 2022 22:20:19 +0000 (+0100) Subject: ipq807x: add QNAP 301w X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=bd17683261e1dde1fdd4223745852de1ce8cfc89;p=openwrt%2Fstaging%2Fsvanheule.git ipq807x: add QNAP 301w QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder --- diff --git a/package/boot/uboot-envtools/files/ipq807x b/package/boot/uboot-envtools/files/ipq807x index 636f334412..3961d4124e 100644 --- a/package/boot/uboot-envtools/files/ipq807x +++ b/package/boot/uboot-envtools/files/ipq807x @@ -22,6 +22,11 @@ xiaomi,ax3600) [ -n "$idx2" ] && \ ubootenv_add_uci_sys_config "/dev/mtd$idx2" "0x0" "0x10000" "0x20000" ;; +qnap,301w) + idx="$(find_mtd_index 0:appsblenv)" + [ -n "$idx" ] && \ + ubootenv_add_uci_config "/dev/mtd$idx" "0x0" "0x20000" "0x20000" "1" + ;; esac config_load ubootenv diff --git a/package/firmware/ipq-wifi/Makefile b/package/firmware/ipq-wifi/Makefile index 2767228080..dbc2b4e227 100644 --- a/package/firmware/ipq-wifi/Makefile +++ b/package/firmware/ipq-wifi/Makefile @@ -38,6 +38,7 @@ ALLWIFIBOARDS:= \ linksys_whw03v2 \ p2w_r619ac \ pakedge_wr-1 \ + qnap_301w \ qxwlan_e2600ac-c1 \ qxwlan_e2600ac-c2 \ redmi_ax6 \ @@ -130,6 +131,7 @@ $(eval $(call generate-ipq-wifi-package,linksys_ea8300,Linksys EA8300)) $(eval $(call generate-ipq-wifi-package,linksys_whw03v2,Linksys WHW03 V2)) $(eval $(call generate-ipq-wifi-package,p2w_r619ac,P&W R619AC)) $(eval $(call generate-ipq-wifi-package,pakedge_wr-1,Pakedge WR-1)) +$(eval $(call generate-ipq-wifi-package,qnap_301w,QNAP 301w)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c1,Qxwlan E2600AC C1)) $(eval $(call generate-ipq-wifi-package,qxwlan_e2600ac-c2,Qxwlan E2600AC C2)) $(eval $(call generate-ipq-wifi-package,redmi_ax6,Redmi AX6)) diff --git a/package/firmware/ipq-wifi/board-qnap_301w.ipq8074 b/package/firmware/ipq-wifi/board-qnap_301w.ipq8074 new file mode 100644 index 0000000000..6b8f8b9ce8 Binary files /dev/null and b/package/firmware/ipq-wifi/board-qnap_301w.ipq8074 differ diff --git a/target/linux/ipq807x/Makefile b/target/linux/ipq807x/Makefile index d02256abf2..539d930ce3 100644 --- a/target/linux/ipq807x/Makefile +++ b/target/linux/ipq807x/Makefile @@ -3,7 +3,7 @@ include $(TOPDIR)/rules.mk ARCH:=aarch64 BOARD:=ipq807x BOARDNAME:=Qualcomm Atheros IPQ807x -FEATURES:=squashfs ramdisk fpu nand rtc +FEATURES:=squashfs ramdisk fpu nand rtc emmc KERNELNAME:=Image dtbs CPU_TYPE:=cortex-a53 SUBTARGETS:=generic diff --git a/target/linux/ipq807x/base-files/etc/board.d/01_leds b/target/linux/ipq807x/base-files/etc/board.d/01_leds index a13ddcbb08..f0a2bdd7bb 100644 --- a/target/linux/ipq807x/base-files/etc/board.d/01_leds +++ b/target/linux/ipq807x/base-files/etc/board.d/01_leds @@ -10,6 +10,14 @@ redmi,ax6|\ xiaomi,ax3600) ucidef_set_led_netdev "wan" "WAN" "blue:network" "wan" ;; +qnap,301w) + ucidef_set_led_netdev "lan1" "LAN1" "green:lan1" "lan1" + ucidef_set_led_netdev "lan2" "LAN2" "green:lan2" "lan2" + ucidef_set_led_netdev "lan3" "LAN3" "green:lan3" "lan3" + ucidef_set_led_netdev "lan4" "LAN4" "green:lan4" "lan4" + ucidef_set_led_netdev "10G_1" "10G_1" "green:10g_1" "10g-1" + ucidef_set_led_netdev "10G_2" "10G_2" "green:10g_2" "10g-2" + ;; esac board_config_flush diff --git a/target/linux/ipq807x/base-files/etc/board.d/02_network b/target/linux/ipq807x/base-files/etc/board.d/02_network index e3f4d4f576..a6ff418a19 100644 --- a/target/linux/ipq807x/base-files/etc/board.d/02_network +++ b/target/linux/ipq807x/base-files/etc/board.d/02_network @@ -14,6 +14,9 @@ ipq807x_setup_interfaces() edimax,cax1800) ucidef_set_interfaces_lan_wan "lan" ;; + qnap,301w) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 10g-2" "10g-1" + ;; redmi,ax6|\ xiaomi,ax3600) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" diff --git a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata index 7f919bafc5..fd431d07da 100644 --- a/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata +++ b/target/linux/ipq807x/base-files/etc/hotplug.d/firmware/11-ath11k-caldata @@ -10,6 +10,7 @@ case "$FIRMWARE" in "ath11k/IPQ8074/hw2.0/cal-ahb-c000000.wifi.bin") case "$board" in edimax,cax1800|\ + qnap,301w|\ redmi,ax6|\ xiaomi,ax3600) caldata_extract "0:art" 0x1000 0x20000 diff --git a/target/linux/ipq807x/base-files/lib/upgrade/mmc.sh b/target/linux/ipq807x/base-files/lib/upgrade/mmc.sh new file mode 100644 index 0000000000..dac9ddd568 --- /dev/null +++ b/target/linux/ipq807x/base-files/lib/upgrade/mmc.sh @@ -0,0 +1,83 @@ +# +# Copyright (C) 2016 lede-project.org +# + +# this can be used as a generic mmc upgrade script +# just add a device entry in platform.sh, +# define "kernelname" and "rootfsname" and call mmc_do_upgrade +# after the kernel and rootfs flash a loopdev (as overlay) is +# setup on top of the rootfs partition +# for the proper function a padded rootfs image is needed, basically +# append "pad-to 64k" to the image definition +# this is based on the ipq806x zyxel.sh mmc upgrade + +. /lib/functions.sh + +mmc_do_upgrade() { + local tar_file="$1" + local rootfs= + local kernel= + + [ -z "$kernel" ] && kernel=$(find_mmc_part ${kernelname}) + [ -z "$rootfs" ] && rootfs=$(find_mmc_part ${rootfsname}) + + [ -z "$kernel" ] && echo "Upgrade failed: kernel partition not found! Rebooting..." && reboot -f + [ -z "$rootfs" ] && echo "Upgrade failed: rootfs partition not found! Rebooting..." && reboot -f + + mmc_do_flash $tar_file $kernel $rootfs + + return 0 +} + +mmc_do_flash() { + local tar_file=$1 + local kernel=$2 + local rootfs=$3 + + # keep sure its unbound + losetup --detach-all || { + echo Failed to detach all loop devices. Skip this try. + reboot -f + } + + # use the first found directory in the tar archive + local board_dir=$(tar tf $tar_file | grep -m 1 '^sysupgrade-.*/$') + board_dir=${board_dir%/} + + echo "flashing kernel to $kernel" + tar xf $tar_file ${board_dir}/kernel -O >$kernel + + echo "flashing rootfs to ${rootfs}" + tar xf $tar_file ${board_dir}/root -O >"${rootfs}" + + # a padded rootfs is needed for overlay fs creation + local offset=$(tar xf $tar_file ${board_dir}/root -O | wc -c) + [ $offset -lt 65536 ] && { + echo Wrong size for rootfs: $offset + sleep 10 + reboot -f + } + + # Mount loop for rootfs_data + local loopdev="$(losetup -f)" + losetup -o $offset $loopdev $rootfs || { + echo "Failed to mount looped rootfs_data." + sleep 10 + reboot -f + } + + echo "Format new rootfs_data at position ${offset}." + mkfs.ext4 -F -L rootfs_data $loopdev + mkdir /tmp/new_root + mount -t ext4 $loopdev /tmp/new_root && { + echo "Saving config to rootfs_data at position ${offset}." + cp -v "$UPGRADE_BACKUP" "/tmp/new_root/$BACKUP_FILE" + umount /tmp/new_root + } + + # Cleanup + losetup -d $loopdev >/dev/null 2>&1 + sync + umount -a + reboot -f +} diff --git a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh index d6e5d04a31..9e8f4796cf 100644 --- a/target/linux/ipq807x/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq807x/base-files/lib/upgrade/platform.sh @@ -45,6 +45,11 @@ platform_do_upgrade() { edimax,cax1800) nand_do_upgrade "$1" ;; + qnap,301w) + kernelname="0:HLOS" + rootfsname="rootfs" + mmc_do_upgrade "$1" + ;; redmi,ax6|\ xiaomi,ax3600) # Make sure that UART is enabled diff --git a/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-301w.dts b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-301w.dts new file mode 100644 index 0000000000..d3e788a36c --- /dev/null +++ b/target/linux/ipq807x/files/arch/arm64/boot/dts/qcom/ipq8072-301w.dts @@ -0,0 +1,410 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/* Copyright (c) 2021, Dirk Buchwalder */ + +/dts-v1/; + +#include "ipq8074.dtsi" +#include "ipq8074-hk-cpu.dtsi" +#include "ipq8074-ess.dtsi" +#include +#include +#include + +/ { + model = "QNAP 301w"; + compatible = "qnap,301w", "qcom,ipq8074"; + + aliases { + serial0 = &blsp1_uart5; + /* + * Aliases as required by u-boot + * to patch MAC addresses + */ + led-boot = &led_system_red; + led-failsafe = &led_system_red; + led-running = &led_pwr_green; + led-upgrade = &led_system_red; + ethernet0 = &dp1; + ethernet1 = &dp2; + ethernet2 = &dp3; + ethernet3 = &dp4; + ethernet4 = &dp5; + ethernet5 = &dp6_syn; + label-mac-device = &dp1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + keys { + compatible = "gpio-keys"; + pinctrl-0 = <&button_pins>; + pinctrl-names = "default"; + + wps-button { + label = "wps"; + gpios = <&tlmm 57 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + reset-button { + label = "reset"; + gpios = <&tlmm 67 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&leds_pins>; + pinctrl-names = "default"; + + led_system_green: led-system-green { + label = "green:system"; + gpios = <&tlmm 1 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led_system_red: led-system-red { + label = "red:system"; + gpios = <&tlmm 3 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led_pwr_green: led-pwr-green { + label = "green:pwr"; + gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-wifi-green { + label = "green:wifi"; + gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan4-green { + label = "green:lan4"; + gpios = <&tlmm 6 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan4-amber { + label = "amber:lan4"; + gpios = <&tlmm 7 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan3-green { + label = "green:lan3"; + gpios = <&tlmm 8 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan3-amber { + label = "amber:lan3"; + gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan2-green { + label = "green:lan2"; + gpios = <&tlmm 12 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan2-amber { + label = "amber:lan2"; + gpios = <&tlmm 13 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan1-green { + label = "green:lan1"; + gpios = <&tlmm 14 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-lan1-amber { + label = "amber:lan1"; + gpios = <&tlmm 15 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-10g-1-green { + label = "green:10g_1"; + gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-10g-1-amber { + label = "amber:10g_1"; + gpios = <&tlmm 56 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-10g-2-green { + label = "green:10g_2"; + gpios = <&tlmm 51 GPIO_ACTIVE_HIGH>; + color = ; + }; + + led-10g-2-amber { + label = "amber:10g_2"; + gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>; + color = ; + }; + }; +}; + +&tlmm { + + mdio_pins: mdio-state { + mdc-pins { + pins = "gpio68"; + function = "mdc"; + drive-strength = <8>; + bias-pull-up; + }; + + mdio-pins { + pins = "gpio69"; + function = "mdio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + button_pins: button-state { + wps-pins { + pins = "gpio57"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + + rst-pins { + pins = "gpio67"; + function = "gpio"; + drive-strength = <8>; + bias-pull-up; + }; + }; + + leds_pins: leds-state { + pins = "gpio1", "gpio3", "gpio4", "gpio6", "gpio7", "gpio8", + "gpio11", "gpio12", "gpio13", "gpio14", "gpio15", "gpio42", + "gpio51", "gpio52", "gpio54", "gpio56"; + function = "gpio"; + drive-strength = <8>; + bias-pull-down; + }; +}; + +&blsp1_uart5 { + status = "okay"; +}; + +&prng { + status = "okay"; +}; + +&ssphy_0 { + status = "okay"; +}; + +&qusb_phy_0 { + status = "okay"; +}; + +&ssphy_1 { + status = "okay"; +}; + +&qusb_phy_1 { + status = "okay"; +}; + +&usb_0 { + status = "okay"; +}; + +&usb_1 { + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&crypto { + status = "okay"; +}; + +&qpic_bam { + status = "okay"; +}; + +&blsp1_spi1 { /* BLSP1 QUP1 */ + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <0>; + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <50000000>; + + partitions { + compatible = "qcom,smem-part"; + }; + }; +}; + +&mdio { + status = "okay"; + + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + reset-gpios = <&tlmm 37 GPIO_ACTIVE_LOW>; + + aqr113c_0: ethernet-phy@0 { + compatible ="ethernet-phy-ieee802.3-c45"; + reg = <0>; + reset-gpios = <&tlmm 59 GPIO_ACTIVE_LOW>; + }; + + aqr113c_8: ethernet-phy@8 { + compatible ="ethernet-phy-ieee802.3-c45"; + reg = <8>; + reset-gpios = <&tlmm 44 GPIO_ACTIVE_LOW>; + }; + + qca8075_16: ethernet-phy@16 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <16>; + }; + + qca8075_17: ethernet-phy@17 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <17>; + }; + + qca8075_18: ethernet-phy@18 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <18>; + }; + + qca8075_19: ethernet-phy@19 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <19>; + }; +}; + +&sdhc_1 { + status = "okay"; + + /* According to the stock dts from the QNAP gpl drop + * the emmc has a problem with the hs400 > hs200 speed switch. + * Therefore remove the mmc-hs400-1_8v property + */ + /delete-property/ mmc-hs400-1_8v; + mmc-hs200-1_8v; + mmc-ddr-1_8v; + vqmmc-supply = <&l11>; +}; + +&switch { + status = "okay"; + + switch_cpu_bmp = <0x1>; /* cpu port bitmap */ + switch_lan_bmp = <0x3e>; /* lan port bitmap */ + switch_wan_bmp = <0xc0>; /* wan port bitmap */ + switch_mac_mode = <0xb>; /* mac mode for uniphy instance0*/ + switch_mac_mode1 = <0xd>; /* mac mode for uniphy instance1*/ + switch_mac_mode2 = <0xd>; /* mac mode for uniphy instance2*/ + bm_tick_mode = <0>; /* bm tick mode */ + tm_tick_mode = <0>; /* tm tick mode */ + + qcom,port_phyinfo { + port@0 { + port_id = <1>; + phy_address = <16>; + }; + port@1 { + port_id = <2>; + phy_address = <17>; + }; + port@2 { + port_id = <3>; + phy_address = <18>; + }; + port@3 { + port_id = <4>; + phy_address = <19>; + }; + port@4 { + port_id = <5>; + phy_address = <8>; + compatible = "ethernet-phy-ieee802.3-c45"; + ethernet-phy-ieee802.3-c45; + }; + port@5 { + port_id = <6>; + phy_address = <0>; + compatible = "ethernet-phy-ieee802.3-c45"; + ethernet-phy-ieee802.3-c45; + }; + }; +}; + +&edma { + status = "okay"; +}; + +&dp1 { + status = "okay"; + phy-handle = <&qca8075_16>; + label = "lan4"; +}; + +&dp2 { + status = "okay"; + phy-handle = <&qca8075_17>; + label = "lan3"; +}; + +&dp3 { + status = "okay"; + phy-handle = <&qca8075_18>; + label = "lan2"; +}; + +&dp4 { + status = "okay"; + phy-handle = <&qca8075_19>; + label = "lan1"; +}; + +&dp5 { + status = "okay"; + qcom,mactype = <1>; + phy-handle = <&aqr113c_8>; + label = "10g-1"; +}; + +&dp6_syn { + status = "okay"; + phy-handle = <&aqr113c_0>; + label = "10g-2"; +}; + +&wifi { + status = "okay"; + + qcom,ath11k-calibration-variant = "QNAP-301w"; +}; diff --git a/target/linux/ipq807x/image/generic.mk b/target/linux/ipq807x/image/generic.mk index 95937512a9..7bf659f80f 100644 --- a/target/linux/ipq807x/image/generic.mk +++ b/target/linux/ipq807x/image/generic.mk @@ -30,6 +30,21 @@ define Device/edimax_cax1800 endef TARGET_DEVICES += edimax_cax1800 +define Device/qnap_301w + $(call Device/FitImage) + DEVICE_VENDOR := QNAP + DEVICE_MODEL := 301w + DEVICE_DTS_CONFIG := config@hk01 + KERNEL_SIZE := 16384k + BLOCKSIZE := 512k + SOC := ipq8072 + IMAGES += factory.bin sysupgrade.bin + IMAGE/factory.bin := append-rootfs | pad-rootfs | pad-to 64k + IMAGE/sysupgrade.bin/squashfs := append-rootfs | pad-to 64k | sysupgrade-tar rootfs=$$$$@ | append-metadata + DEVICE_PACKAGES := ipq-wifi-qnap_301w e2fsprogs kmod-fs-ext4 losetup +endef +TARGET_DEVICES += qnap_301w + define Device/redmi_ax6 $(call Device/xiaomi_ax3600) DEVICE_VENDOR := Redmi