From: Alexandru Gagniuc Date: Sat, 20 Aug 2022 21:10:42 +0000 (-0500) Subject: realtek: split TP-Link SG2000 series devicetree X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=bc9dcfb1ce656e1da694d9d9a6f927b3142ab76a;p=openwrt%2Fstaging%2Fjow.git realtek: split TP-Link SG2000 series devicetree The TP-Link TL-SG2008, TL-SG2008P, and TL-SG2210P use the same board. The main difference is that some footprints are not populated in the lower-end models. To model this with minimal duplication, move the devicetree to a common dtsi, leaving out just the board name. Signed-off-by: Alexandru Gagniuc [remove port relabelling from commit message, already merged with commit 18a2b29aa1c9 ("realtek: tl-sg2008p: fix labeling of lan ports")] Signed-off-by: Sander Vanheule --- diff --git a/target/linux/realtek/dts-5.10/rtl8380_tplink_sg2008p-v1.dts b/target/linux/realtek/dts-5.10/rtl8380_tplink_sg2008p-v1.dts index d464921e50..0fef52984c 100644 --- a/target/linux/realtek/dts-5.10/rtl8380_tplink_sg2008p-v1.dts +++ b/target/linux/realtek/dts-5.10/rtl8380_tplink_sg2008p-v1.dts @@ -1,184 +1,8 @@ // SPDX-License-Identifier: GPL-2.0-or-later -#include "rtl838x.dtsi" - -#include -#include +#include "rtl8380_tplink_sg2xxx.dtsi" / { compatible = "tplink,sg2008p-v1", "realtek,rtl838x-soc"; model = "TP-Link SG2008P v1"; - - aliases { - led-boot = &led_power; - led-failsafe = &led_power; - led-running = &led_power; - led-upgrade = &led_power; - }; - - memory@0 { - device_type = "memory"; - reg = <0x0 0x10000000>; - }; - - keys { - compatible = "gpio-keys"; - - reset { - label = "reset"; - gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; - linux,code = ; - }; - }; - - gpio-restart { - compatible = "gpio-restart"; - gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; - }; - - leds { - compatible = "gpio-leds"; - - led_power: led-0 { - label = "green:power"; - gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; - }; - }; - - i2c1: i2c-gpio-1 { - compatible = "i2c-gpio"; - scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; - i2c-gpio,delay-us = <2>; - #address-cells = <1>; - #size-cells = <0>; - - tps23861@28 { - compatible = "ti,tps23861"; - reg = <0x28>; - shunt-resistor-micro-ohms = <255000>; - }; - }; - - watchdog { - compatible = "linux,wdt-gpio"; - gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; - hw_algo = "toggle"; - /* SGM706 specs: typical 1.6s, but minimum 1.0s. */ - hw_margin_ms = <1000>; - }; - - virtual_flash { - compatible = "mtd-concat"; - - devices = <&syspart &usrpart>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - compatible = "denx,uimage"; - label = "firmware"; - reg = <0x0 0x1a00000>; - }; - }; - }; -}; - -&gpio0 { - watchdog-enable { - gpio-hog; - gpios = <14 GPIO_ACTIVE_LOW>; - output-low; - line-name = "watchdog-enable"; - }; -}; - -&spi0 { - status = "okay"; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <10000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0xe0000>; - read-only; - }; - partition@e0000 { - label = "u-boot-env"; - reg = <0xe0000 0x20000>; - }; - syspart: partition@100000 { - label = "sys"; - reg = <0x100000 0x600000>; - }; - usrpart: partition@700000 { - label = "usrimg1"; - reg = <0x700000 0x1400000>; - }; - partition@1b00000 { - label = "usrappfs"; - reg = <0x1b00000 0x400000>; - }; - partition@1f00000 { - label = "para"; - reg = <0x1f00000 0x100000>; - read-only; - }; - }; - }; -}; - -ðernet0 { - mdio: mdio-bus { - compatible = "realtek,rtl838x-mdio"; - #address-cells = <1>; - #size-cells = <0>; - - INTERNAL_PHY(8) - INTERNAL_PHY(9) - INTERNAL_PHY(10) - INTERNAL_PHY(11) - INTERNAL_PHY(12) - INTERNAL_PHY(13) - INTERNAL_PHY(14) - INTERNAL_PHY(15) - }; -}; - -&switch0 { - ports { - #address-cells = <1>; - #size-cells = <0>; - - SWITCH_PORT(15, 1, internal) - SWITCH_PORT(14, 2, internal) - SWITCH_PORT(13, 3, internal) - SWITCH_PORT(12, 4, internal) - SWITCH_PORT(11, 5, internal) - SWITCH_PORT(10, 6, internal) - SWITCH_PORT(9, 7, internal) - SWITCH_PORT(8, 8, internal) - - port@28 { - ethernet = <ðernet0>; - reg = <28>; - phy-mode = "internal"; - - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; }; diff --git a/target/linux/realtek/dts-5.10/rtl8380_tplink_sg2xxx.dtsi b/target/linux/realtek/dts-5.10/rtl8380_tplink_sg2xxx.dtsi new file mode 100644 index 0000000000..8aa82831ab --- /dev/null +++ b/target/linux/realtek/dts-5.10/rtl8380_tplink_sg2xxx.dtsi @@ -0,0 +1,181 @@ +// SPDX-License-Identifier: GPL-2.0-or-later + +#include "rtl838x.dtsi" + +#include +#include + +/ { + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x10000000>; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio0 2 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio-restart { + compatible = "gpio-restart"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + }; + + leds { + compatible = "gpio-leds"; + + led_power: led-0 { + label = "green:power"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c1: i2c-gpio-1 { + compatible = "i2c-gpio"; + scl-gpios = <&gpio0 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + sda-gpios = <&gpio0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <2>; + #address-cells = <1>; + #size-cells = <0>; + + tps23861@28 { + compatible = "ti,tps23861"; + reg = <0x28>; + shunt-resistor-micro-ohms = <255000>; + }; + }; + + watchdog { + compatible = "linux,wdt-gpio"; + gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>; + hw_algo = "toggle"; + /* SGM706 specs: typical 1.6s, but minimum 1.0s. */ + hw_margin_ms = <1000>; + }; + + virtual_flash { + compatible = "mtd-concat"; + + devices = <&syspart &usrpart>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x0 0x1a00000>; + }; + }; + }; +}; + +&gpio0 { + watchdog-enable { + gpio-hog; + gpios = <14 GPIO_ACTIVE_LOW>; + output-low; + line-name = "watchdog-enable"; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0xe0000>; + read-only; + }; + partition@e0000 { + label = "u-boot-env"; + reg = <0xe0000 0x20000>; + }; + syspart: partition@100000 { + label = "sys"; + reg = <0x100000 0x600000>; + }; + usrpart: partition@700000 { + label = "usrimg1"; + reg = <0x700000 0x1400000>; + }; + partition@1b00000 { + label = "usrappfs"; + reg = <0x1b00000 0x400000>; + }; + partition@1f00000 { + label = "para"; + reg = <0x1f00000 0x100000>; + read-only; + }; + }; + }; +}; + +ðernet0 { + mdio: mdio-bus { + compatible = "realtek,rtl838x-mdio"; + #address-cells = <1>; + #size-cells = <0>; + + INTERNAL_PHY(8) + INTERNAL_PHY(9) + INTERNAL_PHY(10) + INTERNAL_PHY(11) + INTERNAL_PHY(12) + INTERNAL_PHY(13) + INTERNAL_PHY(14) + INTERNAL_PHY(15) + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + SWITCH_PORT(15, 1, internal) + SWITCH_PORT(14, 2, internal) + SWITCH_PORT(13, 3, internal) + SWITCH_PORT(12, 4, internal) + SWITCH_PORT(11, 5, internal) + SWITCH_PORT(10, 6, internal) + SWITCH_PORT(9, 7, internal) + SWITCH_PORT(8, 8, internal) + + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +};