From: Daniel Gimpelevich Date: Sat, 1 Sep 2018 02:28:35 +0000 (-0700) Subject: ath79: add support for Bluesocket BSAP1880 board X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=bc18c2bfe7a80630eea15aa71800b0829ce32634;p=openwrt%2Fstaging%2Fthess.git ath79: add support for Bluesocket BSAP1880 board This board was used in dual-band 802.11n enterprise access points, models BSAP-1800v2 and BSAP-1840, introduced in 2010 by Bluesocket, which was acquired by Adtran in 2011, who has now EOL'ed them. They differed only in that the BSAP-1840's antennae were detachable, while the BSAP-1800v2's were inside the case. They have an external RJ-45 console port, which works with standard Cisco 72-3383-01 console cables. Specification: - System-On-Chip: AR7161 - CPU/Speed: 600 MHz - Flash-Chip: Macronix MX25L12845E - Flash size: 16 MiB - RAM: 64 MiB - Wireless No1: Lite-On WN2601A card: AR9160/AR9103 2.4GHz 802.11bgn - Wireless No2: Lite-On WN2502A card: AR9160/AR9106 5GHz 802.11an - PHY: Vitesse VSC8601, Rev. B Installation: 1. Connect to the serial console using a terminal that supports YMODEM at 115200 bps, 8 data bits, no parity, 1 stop bit 2. Interrupt the bootloader using its password, which is: r00t 3. Issue the "fis init" command, confirming if prompted 4. Look at the length of the openwrt-ath79-generic-*-squashfs-kernel.bin file, and substitute it below, instead of where I have "LeNgTh" 5. Issue the following command, and upload this file using YMODEM protocol load -r -v -b 0x80060000 -m ymodem 6. Issue the following commands, substituting as mentioned above: fis create -b 0x80060000 -l LeNgTh vmlinux_2 load -r -v -b 0x80100000 -m ymodem 7. Using YMODEM, upload openwrt-ath79-generic-*-squashfs-rootfs.bin 8. Issue the "fis free" command, and for the first range in its response, use a hexadecimal calculator to subtract the start from the end in order to substitute it below, with the leading "0x" to specify it in hexadecimal, instead of where I have "LeNgTh" 9. Issue the following commands, substituting as mentioned above: fis create -b 0x80100000 -l LeNgTh -e 0 -r 0 rootfs reset 10.Wait for the status LED to go solid green Tested-by: Brian Gonyer Signed-off-by: Daniel Gimpelevich [fixed obsolete $ARGV in platform_do_upgrade] Signed-off-by: Petr Štetiar --- diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index f7cac3e300..56650c3f6b 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -9,6 +9,8 @@ ath79_setup_interfaces() local board="$1" case "$board" in + adtran,bsap1800-v2|\ + adtran,bsap1840|\ aruba,ap-105|\ avm,fritz300e|\ devolo,dvl1200i|\ @@ -269,6 +271,11 @@ ath79_setup_macs() local board="$1" case "$board" in + adtran,bsap1800-v2|\ + adtran,bsap1840) + fconfig -s -w -d $(find_mtd_part "RedBoot config") -n boot_cntb -x 0 + lan_mac=$(mtd_get_mac_binary "Board data" 2) + ;; avm,fritz300e) lan_mac=$(fritz_tffs -n maca -i $(find_mtd_part "tffs (1)")) ;; diff --git a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches index 7f40285daf..f588b29956 100755 --- a/target/linux/ath79/base-files/etc/board.d/03_gpio_switches +++ b/target/linux/ath79/base-files/etc/board.d/03_gpio_switches @@ -10,6 +10,21 @@ board_config_update board=$(board_name) case "$board" in +adtran,bsap1800-v2|\ +adtran,bsap1840) + ucidef_add_gpio_switch "wifi1_ext_a" "5GHz External Antenna A" "489" "1" + ucidef_add_gpio_switch "wifi1_int_a" "5GHz Internal Antenna A" "493" + ucidef_add_gpio_switch "wifi1_ext_b" "5GHz External Antenna B" "494" "1" + ucidef_add_gpio_switch "wifi1_int_b" "5GHz Internal Antenna B" "495" + ucidef_add_gpio_switch "wifi1_ext_c" "5GHz External Antenna C" "496" "1" + ucidef_add_gpio_switch "wifi1_int_c" "5GHz Internal Antenna C" "497" + ucidef_add_gpio_switch "wifi0_ext_a" "2.4GHz External Antenna A" "505" "1" + ucidef_add_gpio_switch "wifi0_int_a" "2.4GHz Internal Antenna A" "506" + ucidef_add_gpio_switch "wifi0_ext_b" "2.4GHz External Antenna B" "507" "1" + ucidef_add_gpio_switch "wifi0_int_b" "2.4GHz Internal Antenna B" "508" + ucidef_add_gpio_switch "wifi0_ext_c" "2.4GHz External Antenna C" "509" "1" + ucidef_add_gpio_switch "wifi0_int_c" "2.4GHz Internal Antenna C" "510" + ;; comfast,cf-e5) ucidef_add_gpio_switch "lte_power" "LTE Power" "14" "1" ucidef_add_gpio_switch "lte_wakeup" "LTE Wakeup" "11" "1" diff --git a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac index bdb8b71ff7..bf3e14aa9c 100644 --- a/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac +++ b/target/linux/ath79/base-files/etc/hotplug.d/ieee80211/10_fix_wifi_mac @@ -13,6 +13,10 @@ PHYNBR=${DEVPATH##*/phy} board=$(board_name) case "$board" in + adtran,bsap1800-v2|\ + adtran,bsap1840) + macaddr_add "$(mtd_get_mac_binary 'Board data' 2)" $(($PHYNBR * 8 + 1)) > /sys${DEVPATH}/macaddress + ;; iodata,wn-ag300dgr) # There is no eeprom data for 5 GHz wlan in "art" partition # which would allow to patch the macaddress diff --git a/target/linux/ath79/base-files/lib/upgrade/platform.sh b/target/linux/ath79/base-files/lib/upgrade/platform.sh index 8c5a8e52fe..3aff5dee14 100644 --- a/target/linux/ath79/base-files/lib/upgrade/platform.sh +++ b/target/linux/ath79/base-files/lib/upgrade/platform.sh @@ -40,6 +40,10 @@ platform_do_upgrade() { local board=$(board_name) case "$board" in + adtran,bsap1800-v2|\ + adtran,bsap1840) + redboot_fis_do_upgrade "$1" vmlinux_2 + ;; jjplus,ja76pf2) redboot_fis_do_upgrade "$1" linux ;; diff --git a/target/linux/ath79/dts/ar7161_adtran_bsap1800-v2.dts b/target/linux/ath79/dts/ar7161_adtran_bsap1800-v2.dts new file mode 100644 index 0000000000..1745ac76fb --- /dev/null +++ b/target/linux/ath79/dts/ar7161_adtran_bsap1800-v2.dts @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar7161_adtran_bsap1880.dtsi" + +/ { + model = "Adtran/Bluesocket BSAP-1800 v2"; + compatible = "adtran,bsap1800-v2", "qca,ar7161"; +}; diff --git a/target/linux/ath79/dts/ar7161_adtran_bsap1840.dts b/target/linux/ath79/dts/ar7161_adtran_bsap1840.dts new file mode 100644 index 0000000000..38b87a1e32 --- /dev/null +++ b/target/linux/ath79/dts/ar7161_adtran_bsap1840.dts @@ -0,0 +1,9 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "ar7161_adtran_bsap1880.dtsi" + +/ { + model = "Adtran/Bluesocket BSAP-1840"; + compatible = "adtran,bsap1840", "qca,ar7161"; +}; diff --git a/target/linux/ath79/dts/ar7161_adtran_bsap1880.dtsi b/target/linux/ath79/dts/ar7161_adtran_bsap1880.dtsi new file mode 100644 index 0000000000..ba9b588bec --- /dev/null +++ b/target/linux/ath79/dts/ar7161_adtran_bsap1880.dtsi @@ -0,0 +1,99 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar7100.dtsi" + +/ { + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + aliases { + led-boot = &led_green_status; + led-failsafe = &led_yellow_status; + led-running = &led_green_status; + led-upgrade = &led_yellow_status; + }; + + leds { + compatible = "gpio-leds"; + + wlan5g { + label = "bluesocket:green:wifi5g"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wlan2g { + label = "bluesocket:green:wifi2g"; + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + led_green_status: green_status { + label = "bluesocket:green:status"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + led_yellow_status: yellow_status { + label = "bluesocket:yellow:status"; + gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0x1>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + + phy-mode = "rgmii-id"; + phy-handle = <&phy0>; +}; + +&pcie0 { + status = "okay"; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + #address-cells = <1>; + #size-cells = <1>; + compatible = "ecoscentric,redboot-fis-partitions"; + }; + }; +}; + +&uart { + status = "okay"; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 4662383541..3c679fb480 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -85,6 +85,32 @@ define Device/8dev_carambola2 endef TARGET_DEVICES += 8dev_carambola2 +define Device/adtran_bsap1880 + ATH_SOC := ar7161 + DEVICE_VENDOR := Adtran/Bluesocket + DEVICE_PACKAGES += -swconfig -uboot-envtools fconfig + KERNEL := kernel-bin | append-dtb | lzma + KERNEL_INITRAMFS := kernel-bin | append-dtb + IMAGE_SIZE := 11200k + IMAGES += kernel.bin rootfs.bin + IMAGE/kernel.bin := append-kernel | pad-to $$$$(BLOCKSIZE) + IMAGE/rootfs.bin := append-rootfs | pad-rootfs + IMAGE/sysupgrade.bin := append-rootfs | pad-rootfs | combined-image | append-metadata | check-size $$$$(IMAGE_SIZE) +endef + +define Device/adtran_bsap1800-v2 + $(Device/adtran_bsap1880) + DEVICE_MODEL := BSAP-1800 + DEVICE_VARIANT := v2 +endef +TARGET_DEVICES += adtran_bsap1800-v2 + +define Device/adtran_bsap1840 + $(Device/adtran_bsap1880) + DEVICE_MODEL := BSAP-1840 +endef +TARGET_DEVICES += adtran_bsap1840 + define Device/aruba_ap-105 ATH_SOC := ar7161 DEVICE_VENDOR := Aruba