From: Matthias Fuchs Date: Fri, 20 Feb 2009 09:19:19 +0000 (+0100) Subject: ppc4xx: Use correct io accessors for esd 405/440 boards X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=bb57ad4be76d0e2e7f9ec56678235cc9872ff40f;p=project%2Fbcm63xx%2Fu-boot.git ppc4xx: Use correct io accessors for esd 405/440 boards This patch replaces in/out8/16/32 macros by in/out_8/_be16/_be32 macros. Also volatile pointer references are replaced by the new accessors. Signed-off-by: Matthias Fuchs Signed-off-by: Stefan Roese --- diff --git a/board/esd/common/fpga.c b/board/esd/common/fpga.c index 5232dddc9e..62c324386c 100644 --- a/board/esd/common/fpga.c +++ b/board/esd/common/fpga.c @@ -24,6 +24,7 @@ #include #include +#include #include /* ------------------------------------------------------------------------- */ @@ -55,7 +56,7 @@ #define ERROR_FPGA_PRG_DONE -3 /* Timeout after programming */ #ifndef SET_FPGA -# define SET_FPGA(data) out32(GPIO0_OR, data) +# define SET_FPGA(data) out_be32((void *)GPIO0_OR, data) #endif #ifdef FPGA_PROG_ACTIVE_HIGH @@ -85,10 +86,10 @@ SET_FPGA(FPGA_PRG_HIGH | FPGA_CLK_HIGH | FPGA_DATA_HIGH);} /* set data to 1 */ #ifndef FPGA_DONE_STATE -# define FPGA_DONE_STATE (in32(GPIO0_IR) & FPGA_DONE) +# define FPGA_DONE_STATE (in_be32((void *)GPIO0_IR) & FPGA_DONE) #endif #ifndef FPGA_INIT_STATE -# define FPGA_INIT_STATE (in32(GPIO0_IR) & FPGA_INIT) +# define FPGA_INIT_STATE (in_be32((void *)GPIO0_IR) & FPGA_INIT) #endif @@ -139,8 +140,11 @@ static int fpga_boot (const unsigned char *fpgadata, int size) * Setup port pins for fpga programming */ #ifndef CONFIG_M5249 - out32 (GPIO0_ODR, 0x00000000); /* no open drain pins */ - out32 (GPIO0_TCR, in32 (GPIO0_TCR) | FPGA_PRG | FPGA_CLK | FPGA_DATA); /* setup for output */ + out_be32 ((void *)GPIO0_ODR, 0x00000000); /* no open drain pins */ + /* setup for output */ + out_be32 ((void *)GPIO0_TCR, + in_be32 ((void *)GPIO0_TCR) | + FPGA_PRG | FPGA_CLK | FPGA_DATA); #endif SET_FPGA (FPGA_PRG_HIGH | FPGA_CLK_HIGH | FPGA_DATA_HIGH); /* set pins to high */ diff --git a/board/esd/common/lcd.h b/board/esd/common/lcd.h index 3169e6bb5c..01f6019bb2 100644 --- a/board/esd/common/lcd.h +++ b/board/esd/common/lcd.h @@ -40,13 +40,13 @@ #define TRUE (!FALSE) #endif -#define S1D_WRITE_PALETTE(p,i,r,g,b) \ - { \ - ((volatile uchar*)(p))[palette_index] = (uchar)(i); \ - ((volatile uchar*)(p))[palette_value] = (uchar)(r); \ - ((volatile uchar*)(p))[palette_value] = (uchar)(g); \ - ((volatile uchar*)(p))[palette_value] = (uchar)(b); \ - } +#define S1D_WRITE_PALETTE(p,i,r,g,b) \ + { \ + out_8(&((uchar*)(p))[palette_index], (uchar)(i)); \ + out_8(&((uchar*)(p))[palette_index], (uchar)(r)); \ + out_8(&((uchar*)(p))[palette_index], (uchar)(g)); \ + out_8(&((uchar*)(p))[palette_index], (uchar)(b)); \ + } typedef struct { diff --git a/board/esd/common/xilinx_jtag/ports.c b/board/esd/common/xilinx_jtag/ports.c index 3ad94a5b66..ac0d7ac2bb 100644 --- a/board/esd/common/xilinx_jtag/ports.c +++ b/board/esd/common/xilinx_jtag/ports.c @@ -32,6 +32,7 @@ #include #include +#include #include "ports.h" @@ -68,7 +69,7 @@ void setPort(short p,short val) } else { output &= ~JTAG_TCK; } - out32(GPIO0_OR, output); + out_be32((void *)GPIO0_OR, output); } } @@ -98,7 +99,7 @@ unsigned char readTDOBit(void) { unsigned long inputs; - inputs = in32(GPIO0_IR); + inputs = in_be32((void *)GPIO0_IR); if (inputs & JTAG_TDO) return 1; else diff --git a/board/esd/dp405/dp405.c b/board/esd/dp405/dp405.c index eb001dacb6..c32c7c7a0f 100644 --- a/board/esd/dp405/dp405.c +++ b/board/esd/dp405/dp405.c @@ -23,6 +23,7 @@ #include #include +#include #include #include @@ -66,9 +67,11 @@ int board_early_init_f (void) /* * Reset CPLD via GPIO13 (CS4) pin */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~(0x80000000 >> 13)); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) & ~(0x80000000 >> 13)); udelay(1000); /* wait 1ms */ - out32(GPIO0_OR, in32(GPIO0_OR) | (0x80000000 >> 13)); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | (0x80000000 >> 13)); udelay(1000); /* wait 1ms */ return 0; @@ -104,9 +107,10 @@ int checkboard (void) puts(str); } - id1 = trans[(~(in32(GPIO0_IR) >> 5)) & 0x0000000f]; - id2 = trans[(~(in32(GPIO0_IR) >> 9)) & 0x0000000f]; - printf(" (ID=0x%1X%1X, PLD=0x%02X)\n", id2, id1, in8(0xf0001000)); + id1 = trans[(~(in_be32((void *)GPIO0_IR) >> 5)) & 0x0000000f]; + id2 = trans[(~(in_be32((void *)GPIO0_IR) >> 9)) & 0x0000000f]; + printf(" (ID=0x%1X%1X, PLD=0x%02X)\n", + id2, id1, in_8((void *)0xf0001000)); return 0; } diff --git a/board/esd/du405/du405.c b/board/esd/du405/du405.c index 3bb34fd826..8e9ac28b18 100644 --- a/board/esd/du405/du405.c +++ b/board/esd/du405/du405.c @@ -188,8 +188,8 @@ int checkboard (void) /* * Reset external DUART via FPGA */ - *(volatile unsigned char *) FPGA_MODE_REG = 0xff; /* reset high active */ - *(volatile unsigned char *) FPGA_MODE_REG = 0x00; /* low again */ + out_8((void *)FPGA_MODE_REG, 0xff); /* reset high active */ + out_8((void *)FPGA_MODE_REG, 0x00); /* low again */ return 0; } diff --git a/board/esd/du440/du440.c b/board/esd/du440/du440.c index f9b91b5937..45dfa6fd77 100644 --- a/board/esd/du440/du440.c +++ b/board/esd/du440/du440.c @@ -310,8 +310,8 @@ int misc_init_r(void) int pld_revision(void) { - out8(CONFIG_SYS_CPLD_BASE, 0x00); - return (int)(in8(CONFIG_SYS_CPLD_BASE) & CPLD_VERSION_MASK); + out_8((void *)CONFIG_SYS_CPLD_BASE, 0x00); + return (int)(in_8((void *)CONFIG_SYS_CPLD_BASE) & CPLD_VERSION_MASK); } int board_revision(void) @@ -872,12 +872,12 @@ static int got_pldirq; static int pld_interrupt(u32 arg) { int rc = -1; /* not for us */ - u8 status = in8(CONFIG_SYS_CPLD_BASE); + u8 status = in_8((void *)CONFIG_SYS_CPLD_BASE); /* check for PLD interrupt */ if (status & PWR_INT_FLAG) { /* reset this int */ - out8(CONFIG_SYS_CPLD_BASE, 0); + out_8((void *)CONFIG_SYS_CPLD_BASE, 0); rc = 0; got_pldirq = 1; /* trigger backend */ } @@ -890,7 +890,7 @@ int do_waitpwrirq(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) got_pldirq = 0; /* clear any pending interrupt */ - out8(CONFIG_SYS_CPLD_BASE, 0); + out_8((void *)CONFIG_SYS_CPLD_BASE, 0); irq_install_handler(CPLD_IRQ, (interrupt_handler_t *)pld_interrupt, 0); @@ -906,7 +906,8 @@ int do_waitpwrirq(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) if (got_pldirq) { printf("Got interrupt!\n"); printf("Power %sready!\n", - in8(CONFIG_SYS_CPLD_BASE) & PWR_RDY ? "":"NOT "); + in_8((void *)CONFIG_SYS_CPLD_BASE) & + PWR_RDY ? "":"NOT "); } irq_free_handler(CPLD_IRQ); diff --git a/board/esd/hh405/hh405.c b/board/esd/hh405/hh405.c index ae3bc80aa0..eab952c566 100644 --- a/board/esd/hh405/hh405.c +++ b/board/esd/hh405/hh405.c @@ -29,6 +29,7 @@ #include #include +#include #include #include #include @@ -36,6 +37,26 @@ DECLARE_GLOBAL_DATA_PTR; +/* FPGA internal regs */ +#define FPGA_CTRL ((u16 *)(CONFIG_SYS_FPGA_BASE_ADDR + 0x000)) +#define FPGA_STATUS ((u16 *)(CONFIG_SYS_FPGA_BASE_ADDR + 0x002)) +#define FPGA_CTR ((u16 *)(CONFIG_SYS_FPGA_BASE_ADDR + 0x004)) +#define FPGA_BL ((u16 *)(CONFIG_SYS_FPGA_BASE_ADDR + 0x006)) + +/* FPGA Control Reg */ +#define FPGA_CTRL_REV0 0x0001 +#define FPGA_CTRL_REV1 0x0002 +#define FPGA_CTRL_VGA0_BL 0x0004 +#define FPGA_CTRL_VGA0_BL_MODE 0x0008 +#define FPGA_CTRL_CF_RESET 0x0040 +#define FPGA_CTRL_PS2_PWR 0x0080 +#define FPGA_CTRL_CF_PWRN 0x0100 /* low active */ +#define FPGA_CTRL_CF_BUS_EN 0x0200 +#define FPGA_CTRL_LCD_CLK 0x7000 /* mask for lcd clock */ +#define FPGA_CTRL_OW_ENABLE 0x8000 + +#define FPGA_STATUS_CF_DETECT 0x8000 + #ifdef CONFIG_VIDEO_SM501 #define SWAP32(x) ((((x) & 0x000000ff) << 24) | (((x) & 0x0000ff00) << 8)|\ @@ -297,22 +318,22 @@ int board_revision(void) /* * Setup GPIO pins (BLAST/GPIO0 and GPIO9 as GPIO) */ - osrh_reg = in32(GPIO0_OSRH); - isr1h_reg = in32(GPIO0_ISR1H); - tcr_reg = in32(GPIO0_TCR); - out32(GPIO0_OSRH, osrh_reg & ~0xC0003000); /* output select */ - out32(GPIO0_ISR1H, isr1h_reg | 0xC0003000); /* input select */ - out32(GPIO0_TCR, tcr_reg & ~0x80400000); /* select input */ + osrh_reg = in_be32((void *)GPIO0_OSRH); + isr1h_reg = in_be32((void *)GPIO0_ISR1H); + tcr_reg = in_be32((void *)GPIO0_TCR); + out_be32((void *)GPIO0_OSRH, osrh_reg & ~0xC0003000); /* output select */ + out_be32((void *)GPIO0_ISR1H, isr1h_reg | 0xC0003000); /* input select */ + out_be32((void *)GPIO0_TCR, tcr_reg & ~0x80400000); /* select input */ udelay(1000); /* wait some time before reading input */ - value = in32(GPIO0_IR) & 0x80400000; /* get config bits */ + value = in_be32((void *)GPIO0_IR) & 0x80400000; /* get config bits */ /* * Restore GPIO settings */ - out32(GPIO0_OSRH, osrh_reg); /* output select */ - out32(GPIO0_ISR1H, isr1h_reg); /* input select */ - out32(GPIO0_TCR, tcr_reg); /* enable output driver for outputs */ + out_be32((void *)GPIO0_OSRH, osrh_reg); /* output select */ + out_be32((void *)GPIO0_ISR1H, isr1h_reg); /* input select */ + out_be32((void *)GPIO0_TCR, tcr_reg); /* enable output driver for outputs */ if (value & 0x80000000) { /* Revision 1.0 or 1.1 detected */ @@ -353,7 +374,7 @@ int board_early_init_f (void) /* * EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us */ - mtebc (epcr, 0xa8400000); /* ebc always driven */ + mtebc(epcr, 0xa8400000); /* ebc always driven */ return 0; } @@ -362,27 +383,26 @@ int cf_enable(void) { int i; - volatile unsigned short *fpga_ctrl = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL); - volatile unsigned short *fpga_status = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL + 2); - if (gd->board_type >= 2) { - if (*fpga_status & CONFIG_SYS_FPGA_STATUS_CF_DETECT) { - if (!(*fpga_ctrl & CONFIG_SYS_FPGA_CTRL_CF_BUS_EN)) { - *fpga_ctrl &= ~CONFIG_SYS_FPGA_CTRL_CF_PWRN; + if (in_be16(FPGA_STATUS) & FPGA_STATUS_CF_DETECT) { + if (!(in_be16(FPGA_CTRL) & FPGA_CTRL_CF_BUS_EN)) { + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) & ~FPGA_CTRL_CF_PWRN); for (i=0; i<300; i++) udelay(1000); - *fpga_ctrl |= CONFIG_SYS_FPGA_CTRL_CF_BUS_EN; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) | FPGA_CTRL_CF_BUS_EN); for (i=0; i<20; i++) udelay(1000); } } else { - *fpga_ctrl &= ~CONFIG_SYS_FPGA_CTRL_CF_BUS_EN; - *fpga_ctrl |= CONFIG_SYS_FPGA_CTRL_CF_PWRN; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) & ~FPGA_CTRL_CF_BUS_EN); + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) | FPGA_CTRL_CF_PWRN); } } @@ -391,12 +411,6 @@ int cf_enable(void) int misc_init_r (void) { - volatile unsigned short *fpga_ctrl = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL); - volatile unsigned short *lcd_contrast = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL + 4); - volatile unsigned short *lcd_backlight = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL + 6); unsigned char *dst; ulong len = sizeof(fpgadata); int status; @@ -460,36 +474,43 @@ int misc_init_r (void) /* * Reset FPGA via FPGA_INIT pin */ - out32(GPIO0_TCR, in32(GPIO0_TCR) | FPGA_INIT); /* setup FPGA_INIT as output */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~FPGA_INIT); /* reset low */ + /* setup FPGA_INIT as output */ + out_be32((void *)GPIO0_TCR, + in_be32((void *)GPIO0_TCR) | FPGA_INIT); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) & ~FPGA_INIT); /* reset low */ udelay(1000); /* wait 1ms */ - out32(GPIO0_OR, in32(GPIO0_OR) | FPGA_INIT); /* reset high */ + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | FPGA_INIT); /* reset high */ udelay(1000); /* wait 1ms */ /* * Write Board revision into FPGA */ - *fpga_ctrl |= gd->board_type & 0x0003; + out_be16(FPGA_CTRL, in_be16(FPGA_CTRL) | (gd->board_type & 0x0003)); /* * Setup and enable EEPROM write protection */ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_EEPROM_WP); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | CONFIG_SYS_EEPROM_WP); /* * Reset touch-screen controller */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_TOUCH_RST); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_TOUCH_RST); udelay(1000); - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_TOUCH_RST); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | CONFIG_SYS_TOUCH_RST); /* * Enable power on PS/2 interface (with reset) */ - *fpga_ctrl &= ~(CONFIG_SYS_FPGA_CTRL_PS2_PWR); + out_be16(FPGA_CTRL, in_be16(FPGA_CTRL) & ~FPGA_CTRL_PS2_PWR); for (i=0;i<500;i++) udelay(1000); - *fpga_ctrl |= (CONFIG_SYS_FPGA_CTRL_PS2_PWR); + out_be16(FPGA_CTRL, in_be16(FPGA_CTRL) | FPGA_CTRL_PS2_PWR); /* * Get contrast value from environment variable @@ -498,7 +519,8 @@ int misc_init_r (void) if (str) { contrast0 = simple_strtol(str, NULL, 16); if (contrast0 > 255) { - printf("ERROR: contrast0 value too high (0x%lx)!\n", contrast0); + printf("ERROR: contrast0 value too high (0x%lx)!\n", + contrast0); contrast0 = 0xffffffff; } } @@ -512,8 +534,9 @@ int misc_init_r (void) /* * Switch backlight on */ - *fpga_ctrl |= CONFIG_SYS_FPGA_CTRL_VGA0_BL; - *lcd_backlight = 0x0000; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) | FPGA_CTRL_VGA0_BL); + out_be16(FPGA_BL, 0x0000); lcd_setup(1, 0); lcd_init((uchar *)CONFIG_SYS_LCD_BIG_REG, (uchar *)CONFIG_SYS_LCD_BIG_MEM, @@ -524,8 +547,9 @@ int misc_init_r (void) /* * Switch backlight on */ - *fpga_ctrl &= ~CONFIG_SYS_FPGA_CTRL_VGA0_BL; - *lcd_backlight = 0x0000; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) & ~FPGA_CTRL_VGA0_BL); + out_be16(FPGA_BL, 0x0000); lcd_setup(1, 0); lcd_init((uchar *)CONFIG_SYS_LCD_BIG_REG, (uchar *)CONFIG_SYS_LCD_BIG_MEM, @@ -537,19 +561,22 @@ int misc_init_r (void) * Set default display contrast voltage */ if (contrast0 == 0xffffffff) { - *lcd_contrast = 0x0082; + out_be16(FPGA_CTR, 0x0082); } else { - *lcd_contrast = contrast0; + out_be16(FPGA_CTR, contrast0); } - *lcd_backlight = 0xffff; + out_be16(FPGA_BL, 0xffff); /* * Switch backlight on */ - *fpga_ctrl |= CONFIG_SYS_FPGA_CTRL_VGA0_BL | CONFIG_SYS_FPGA_CTRL_VGA0_BL_MODE; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) | + FPGA_CTRL_VGA0_BL | + FPGA_CTRL_VGA0_BL_MODE); /* * Set lcd clock (small epson) */ - *fpga_ctrl |= LCD_CLK_06250; + out_be16(FPGA_CTRL, in_be16(FPGA_CTRL) | LCD_CLK_06250); udelay(100); /* wait for 100 us */ lcd_setup(0, 1); @@ -562,19 +589,25 @@ int misc_init_r (void) * Set default display contrast voltage */ if (contrast0 == 0xffffffff) { - *lcd_contrast = 0x0060; + out_be16(FPGA_CTR, 0x0060); } else { - *lcd_contrast = contrast0; + out_be16(FPGA_CTR, contrast0); } - *lcd_backlight = 0xffff; + out_be16(FPGA_BL, 0xffff); /* * Switch backlight on */ - *fpga_ctrl |= CONFIG_SYS_FPGA_CTRL_VGA0_BL | CONFIG_SYS_FPGA_CTRL_VGA0_BL_MODE; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) | + FPGA_CTRL_VGA0_BL | + FPGA_CTRL_VGA0_BL_MODE); /* * Set lcd clock (small epson), enable 1-wire interface */ - *fpga_ctrl |= LCD_CLK_08330 | CONFIG_SYS_FPGA_CTRL_OW_ENABLE; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) | + LCD_CLK_08330 | + FPGA_CTRL_OW_ENABLE); lcd_setup(0, 1); lcd_init((uchar *)CONFIG_SYS_LCD_SMALL_REG, (uchar *)CONFIG_SYS_LCD_SMALL_MEM, @@ -593,10 +626,10 @@ int misc_init_r (void) puts("VGA: SM501 with 8 MB "); if (strcmp(str, "ppc221") == 0) { printf("(800*600, %dbpp)\n", BPP); - *lcd_backlight = 0x002d; /* max. allowed brightness */ + out_be16(FPGA_BL, 0x002d); /* max. allowed brightness */ } else if (strcmp(str, "ppc231") == 0) { printf("(1024*768, %dbpp)\n", BPP); - *lcd_backlight = 0x0000; + out_be16(FPGA_BL, 0x0000); } else { printf("Unsupported bd_type defined (%s) -> No display configured!\n", str); return 0; @@ -646,21 +679,21 @@ int checkboard (void) #ifdef CONFIG_IDE_RESET void ide_set_reset(int on) { - volatile unsigned short *fpga_mode = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL); - volatile unsigned short *fpga_status = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL + 2); - - if (((gd->board_type >= 2) && (*fpga_status & CONFIG_SYS_FPGA_STATUS_CF_DETECT)) || + if (((gd->board_type >= 2) && + (in_be16(FPGA_STATUS) & FPGA_STATUS_CF_DETECT)) || (gd->board_type < 2)) { /* * Assert or deassert CompactFlash Reset Pin */ if (on) { /* assert RESET */ cf_enable(); - *fpga_mode &= ~(CONFIG_SYS_FPGA_CTRL_CF_RESET); + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) & + ~FPGA_CTRL_CF_RESET); } else { /* release RESET */ - *fpga_mode |= CONFIG_SYS_FPGA_CTRL_CF_RESET; + out_be16(FPGA_CTRL, + in_be16(FPGA_CTRL) | + FPGA_CTRL_CF_RESET); } } } @@ -684,17 +717,20 @@ int eeprom_write_enable (unsigned dev_addr, int state) switch (state) { case 1: /* Enable write access, clear bit GPIO_SINT2. */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_EEPROM_WP); state = 0; break; case 0: /* Disable write access, set bit GPIO_SINT2. */ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_EEPROM_WP); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | CONFIG_SYS_EEPROM_WP); state = 0; break; default: /* Read current status back. */ - state = (0 == (in32(GPIO0_OR) & CONFIG_SYS_EEPROM_WP)); + state = (0 == (in_be32((void *)GPIO0_OR) & + CONFIG_SYS_EEPROM_WP)); break; } } diff --git a/board/esd/hub405/hub405.c b/board/esd/hub405/hub405.c index 8785e6c84f..03e5ad7dd1 100644 --- a/board/esd/hub405/hub405.c +++ b/board/esd/hub405/hub405.c @@ -23,6 +23,7 @@ #include #include +#include #include #include @@ -44,22 +45,22 @@ int board_revision(void) /* * Setup GPIO pin(s) (IRQ6/GPIO23) */ - osrl_reg = in32(GPIO0_OSRH); - isr1l_reg = in32(GPIO0_ISR1H); - tcr_reg = in32(GPIO0_TCR); - out32(GPIO0_OSRH, osrl_reg & ~0x00030000); /* output select */ - out32(GPIO0_ISR1H, isr1l_reg | 0x00030000); /* input select */ - out32(GPIO0_TCR, tcr_reg & ~0x00000100); /* select input */ + osrl_reg = in_be32((void *)GPIO0_OSRH); + isr1l_reg = in_be32((void *)GPIO0_ISR1H); + tcr_reg = in_be32((void *)GPIO0_TCR); + out_be32((void *)GPIO0_OSRH, osrl_reg & ~0x00030000); /* output select */ + out_be32((void *)GPIO0_ISR1H, isr1l_reg | 0x00030000); /* input select */ + out_be32((void *)GPIO0_TCR, tcr_reg & ~0x00000100); /* select input */ udelay(1000); /* wait some time before reading input */ - value = in32(GPIO0_IR) & 0x00000100; /* get config bits */ + value = in_be32((void *)GPIO0_IR) & 0x00000100; /* get config bits */ /* * Restore GPIO settings */ - out32(GPIO0_OSRH, osrl_reg); /* output select */ - out32(GPIO0_ISR1H, isr1l_reg); /* input select */ - out32(GPIO0_TCR, tcr_reg); /* enable output driver for outputs */ + out_be32((void *)GPIO0_OSRH, osrl_reg); /* output select */ + out_be32((void *)GPIO0_ISR1H, isr1l_reg); /* input select */ + out_be32((void *)GPIO0_TCR, tcr_reg); /* enable output driver for outputs */ if (value & 0x00000100) { /* Revision 1.1 or 1.2 detected */ @@ -101,13 +102,9 @@ int board_early_init_f (void) return 0; } +#define LED_REG (DUART0_BA + 0x20) int misc_init_r (void) { - volatile unsigned char *duart0_mcr = (unsigned char *)((ulong)DUART0_BA + 4); - volatile unsigned char *duart1_mcr = (unsigned char *)((ulong)DUART1_BA + 4); - volatile unsigned char *duart2_mcr = (unsigned char *)((ulong)DUART2_BA + 4); - volatile unsigned char *duart3_mcr = (unsigned char *)((ulong)DUART3_BA + 4); - volatile unsigned char *led_reg = (unsigned char *)((ulong)DUART0_BA + 0x20); unsigned long val; int delay, flashcnt; char *str; @@ -116,16 +113,17 @@ int misc_init_r (void) /* * Enable interrupts in exar duart mcr[3] */ - *duart0_mcr = 0x08; - *duart1_mcr = 0x08; - *duart2_mcr = 0x08; - *duart3_mcr = 0x08; + out_8((void *)(DUART0_BA + 4), 0x08); + out_8((void *)(DUART1_BA + 4), 0x08); + out_8((void *)(DUART2_BA + 4), 0x08); + out_8((void *)(DUART3_BA + 4), 0x08); /* * Set RS232/RS422 control (RS232 = high on GPIO) */ - val = in32(GPIO0_OR); - val &= ~(CONFIG_SYS_UART2_RS232 | CONFIG_SYS_UART3_RS232 | CONFIG_SYS_UART4_RS232 | CONFIG_SYS_UART5_RS232); + val = in_be32((void *)GPIO0_OR); + val &= ~(CONFIG_SYS_UART2_RS232 | CONFIG_SYS_UART3_RS232 | + CONFIG_SYS_UART4_RS232 | CONFIG_SYS_UART5_RS232); str = getenv("phys0"); if (!str || (str && (str[0] == '0'))) @@ -143,7 +141,7 @@ int misc_init_r (void) if (!str || (str && (str[0] == '0'))) val |= CONFIG_SYS_UART5_RS232; - out32(GPIO0_OR, val); + out_be32((void *)GPIO0_OR, val); /* * check board type and setup AP power @@ -160,23 +158,27 @@ int misc_init_r (void) * Flash LEDs */ for (flashcnt = 0; flashcnt < 3; flashcnt++) { - *led_reg = led_reg_default; /* LED_A..D off */ + /* LED_A..D off */ + out_8((void *)LED_REG, led_reg_default); for (delay = 0; delay < 100; delay++) udelay(1000); - *led_reg = led_reg_default | 0xf0; /* LED_A..D on */ + /* LED_A..D on */ + out_8((void *)LED_REG, led_reg_default | 0xf0); for (delay = 0; delay < 50; delay++) udelay(1000); } - *led_reg = led_reg_default; + out_8((void *)LED_REG, led_reg_default); } } /* * Reset external DUARTs */ - out32(GPIO0_OR, in32(GPIO0_OR) | CONFIG_SYS_DUART_RST); /* set reset to high */ + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | CONFIG_SYS_DUART_RST); /* set reset to high */ udelay(10); /* wait 10us */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~CONFIG_SYS_DUART_RST); /* set reset to low */ + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_DUART_RST); /* set reset to low */ udelay(1000); /* wait 1ms */ /* diff --git a/board/esd/pci405/pci405.c b/board/esd/pci405/pci405.c index 0602abf9c4..8973f97095 100644 --- a/board/esd/pci405/pci405.c +++ b/board/esd/pci405/pci405.c @@ -338,17 +338,17 @@ int checkboard (void) } /* ------------------------------------------------------------------------- */ +#define UART1_MCR 0xef600404 int wpeeprom(int wp) { int wp_state = wp; - volatile unsigned char *uart1_mcr = (volatile unsigned char *)0xef600404; if (wp == 1) { - *uart1_mcr &= ~0x02; + out_8((void *)UART1_MCR, in_8((void *)UART1_MCR) & ~0x02); } else if (wp == 0) { - *uart1_mcr |= 0x02; + out_8((void *)UART1_MCR, in_8((void *)UART1_MCR) | 0x02); } else { - if (*uart1_mcr & 0x02) { + if (in_8((void *)UART1_MCR) & 0x02) { wp_state = 0; } else { wp_state = 1; diff --git a/board/esd/plu405/plu405.c b/board/esd/plu405/plu405.c index 7c0aaa2e32..a94604a2f2 100644 --- a/board/esd/plu405/plu405.c +++ b/board/esd/plu405/plu405.c @@ -237,18 +237,18 @@ int checkboard (void) } #ifdef CONFIG_IDE_RESET +#define FPGA_CTRL (CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL) void ide_set_reset(int on) { - volatile unsigned short *fpga_mode = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL); - /* * Assert or deassert CompactFlash Reset Pin */ if (on) { /* assert RESET */ - *fpga_mode &= ~(CONFIG_SYS_FPGA_CTRL_CF_RESET); + out_be16((void *)FPGA_CTRL, + in_be16((void *)FPGA_CTRL) & ~CONFIG_SYS_FPGA_CTRL_CF_RESET); } else { /* release RESET */ - *fpga_mode |= CONFIG_SYS_FPGA_CTRL_CF_RESET; + out_be16((void *)FPGA_CTRL, + in_be16((void *)FPGA_CTRL) | CONFIG_SYS_FPGA_CTRL_CF_RESET); } } #endif /* CONFIG_IDE_RESET */ diff --git a/board/esd/pmc440/cmd_pmc440.c b/board/esd/pmc440/cmd_pmc440.c index 7808d4d17e..0fbc3dc239 100644 --- a/board/esd/pmc440/cmd_pmc440.c +++ b/board/esd/pmc440/cmd_pmc440.c @@ -242,7 +242,7 @@ int do_fifo(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) "address %08x\n", n, data, f); for (i=0; ihelp); diff --git a/board/esd/pmc440/pmc440.c b/board/esd/pmc440/pmc440.c index 3824105342..2ab944ddf0 100644 --- a/board/esd/pmc440/pmc440.c +++ b/board/esd/pmc440/pmc440.c @@ -107,31 +107,31 @@ int board_early_init_f(void) * Setup the GPIO pins * TODO: setup GPIOs via CONFIG_SYS_4xx_GPIO_TABLE in board's config file */ - out32(GPIO0_OR, 0x40000102); - out32(GPIO0_TCR, 0x4c90011f); - out32(GPIO0_OSRL, 0x28051400); - out32(GPIO0_OSRH, 0x55005000); - out32(GPIO0_TSRL, 0x08051400); - out32(GPIO0_TSRH, 0x55005000); - out32(GPIO0_ISR1L, 0x54000000); - out32(GPIO0_ISR1H, 0x00000000); - out32(GPIO0_ISR2L, 0x44000000); - out32(GPIO0_ISR2H, 0x00000100); - out32(GPIO0_ISR3L, 0x00000000); - out32(GPIO0_ISR3H, 0x00000000); - - out32(GPIO1_OR, 0x80002408); - out32(GPIO1_TCR, 0xd6003c08); - out32(GPIO1_OSRL, 0x0a5a0000); - out32(GPIO1_OSRH, 0x00000000); - out32(GPIO1_TSRL, 0x00000000); - out32(GPIO1_TSRH, 0x00000000); - out32(GPIO1_ISR1L, 0x00005555); - out32(GPIO1_ISR1H, 0x40000000); - out32(GPIO1_ISR2L, 0x04010000); - out32(GPIO1_ISR2H, 0x00000000); - out32(GPIO1_ISR3L, 0x01400000); - out32(GPIO1_ISR3H, 0x00000000); + out_be32((void *)GPIO0_OR, 0x40000102); + out_be32((void *)GPIO0_TCR, 0x4c90011f); + out_be32((void *)GPIO0_OSRL, 0x28051400); + out_be32((void *)GPIO0_OSRH, 0x55005000); + out_be32((void *)GPIO0_TSRL, 0x08051400); + out_be32((void *)GPIO0_TSRH, 0x55005000); + out_be32((void *)GPIO0_ISR1L, 0x54000000); + out_be32((void *)GPIO0_ISR1H, 0x00000000); + out_be32((void *)GPIO0_ISR2L, 0x44000000); + out_be32((void *)GPIO0_ISR2H, 0x00000100); + out_be32((void *)GPIO0_ISR3L, 0x00000000); + out_be32((void *)GPIO0_ISR3H, 0x00000000); + + out_be32((void *)GPIO1_OR, 0x80002408); + out_be32((void *)GPIO1_TCR, 0xd6003c08); + out_be32((void *)GPIO1_OSRL, 0x0a5a0000); + out_be32((void *)GPIO1_OSRH, 0x00000000); + out_be32((void *)GPIO1_TSRL, 0x00000000); + out_be32((void *)GPIO1_TSRH, 0x00000000); + out_be32((void *)GPIO1_ISR1L, 0x00005555); + out_be32((void *)GPIO1_ISR1H, 0x40000000); + out_be32((void *)GPIO1_ISR2L, 0x04010000); + out_be32((void *)GPIO1_ISR2H, 0x00000000); + out_be32((void *)GPIO1_ISR3L, 0x01400000); + out_be32((void *)GPIO1_ISR3H, 0x00000000); /* patch PLB:PCI divider for 66MHz PCI */ mfcpr(clk_spcid, reg); @@ -804,17 +804,20 @@ int eeprom_write_enable(unsigned dev_addr, int state) switch (state) { case 1: /* Enable write access, clear bit GPIO_SINT2. */ - out32(GPIO0_OR, in32(GPIO0_OR) & ~GPIO0_EP_EEP); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) & ~GPIO0_EP_EEP); state = 0; break; case 0: /* Disable write access, set bit GPIO_SINT2. */ - out32(GPIO0_OR, in32(GPIO0_OR) | GPIO0_EP_EEP); + out_be32((void *)GPIO0_OR, + in_be32((void *)GPIO0_OR) | GPIO0_EP_EEP); state = 0; break; default: /* Read current status back. */ - state = (0 == (in32(GPIO0_OR) & GPIO0_EP_EEP)); + state = (0 == (in_be32((void *)GPIO0_OR) + & GPIO0_EP_EEP)); break; } } diff --git a/board/esd/tasreg/tasreg.c b/board/esd/tasreg/tasreg.c index 80ff2376b8..760c71d264 100644 --- a/board/esd/tasreg/tasreg.c +++ b/board/esd/tasreg/tasreg.c @@ -25,6 +25,7 @@ #include #include #include +#include /* Prototypes */ @@ -118,7 +119,7 @@ phys_size_t initdram (int board_type) { /** Precharge sequence **/ mbar_writeLong(MCFSIM_DACR0, 0x0000332c); /* Set DACR0[IP] (bit 3) */ - *((volatile unsigned long *) 0x00) = junk; /* write to a memory location to init. precharge */ + out_be32((void *)0, junk); /* write to a memory location to init. precharge */ udelay(0x10); /* Allow several Precharge cycles */ /** Refresh Sequence **/ @@ -127,7 +128,7 @@ phys_size_t initdram (int board_type) { /** Mode Register initialization **/ mbar_writeLong(MCFSIM_DACR0, 0x0000b364); /* Enable DACR0[IMRS] (bit 6); RE remains enabled */ - *((volatile unsigned long *) 0x800) = junk; /* Access RAM to initialize the mode register */ + out_be32((void *)0x800, junk); /* Access RAM to initialize the mode register */ return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; }; @@ -258,7 +259,7 @@ int do_codec(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[]) { uchar buf[8]; - *(volatile ushort *)0xe0000000 = 0x4000; + out_be16((void *)0xe0000000, 0x4000); udelay(5000); /* wait for 5ms */ diff --git a/board/esd/voh405/voh405.c b/board/esd/voh405/voh405.c index 5480105b48..96a04b3ff8 100644 --- a/board/esd/voh405/voh405.c +++ b/board/esd/voh405/voh405.c @@ -297,18 +297,18 @@ int checkboard (void) } #ifdef CONFIG_IDE_RESET +#define FPGA_MODE (CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL) void ide_set_reset(int on) { - volatile unsigned short *fpga_mode = - (unsigned short *)((ulong)CONFIG_SYS_FPGA_BASE_ADDR + CONFIG_SYS_FPGA_CTRL); - /* * Assert or deassert CompactFlash Reset Pin */ if (on) { /* assert RESET */ - *fpga_mode &= ~(CONFIG_SYS_FPGA_CTRL_CF_RESET); + out_be16((void *)FPGA_MODE, + in_be16((void *)FPGA_MODE) & ~CONFIG_SYS_FPGA_CTRL_CF_RESET); } else { /* release RESET */ - *fpga_mode |= CONFIG_SYS_FPGA_CTRL_CF_RESET; + out_be16((void *)FPGA_MODE, + in_be16((void *)FPGA_MODE) | CONFIG_SYS_FPGA_CTRL_CF_RESET); } } #endif /* CONFIG_IDE_RESET */ diff --git a/include/configs/HH405.h b/include/configs/HH405.h index ed9a235f6e..92335239df 100644 --- a/include/configs/HH405.h +++ b/include/configs/HH405.h @@ -413,23 +413,6 @@ #define CONFIG_SYS_FPGA_BASE_ADDR 0xF0100100 /* FPGA internal Base Address */ -/* FPGA internal regs */ -#define CONFIG_SYS_FPGA_CTRL 0x000 - -/* FPGA Control Reg */ -#define CONFIG_SYS_FPGA_CTRL_REV0 0x0001 -#define CONFIG_SYS_FPGA_CTRL_REV1 0x0002 -#define CONFIG_SYS_FPGA_CTRL_VGA0_BL 0x0004 -#define CONFIG_SYS_FPGA_CTRL_VGA0_BL_MODE 0x0008 -#define CONFIG_SYS_FPGA_CTRL_CF_RESET 0x0040 -#define CONFIG_SYS_FPGA_CTRL_PS2_PWR 0x0080 -#define CONFIG_SYS_FPGA_CTRL_CF_PWRN 0x0100 /* low active */ -#define CONFIG_SYS_FPGA_CTRL_CF_BUS_EN 0x0200 -#define CONFIG_SYS_FPGA_CTRL_LCD_CLK 0x7000 /* Mask for lcd clock */ -#define CONFIG_SYS_FPGA_CTRL_OW_ENABLE 0x8000 - -#define CONFIG_SYS_FPGA_STATUS_CF_DETECT 0x8000 - #define LCD_CLK_OFF 0x0000 /* Off */ #define LCD_CLK_02083 0x1000 /* 2.083 MHz */ #define LCD_CLK_03135 0x2000 /* 3.135 MHz */