From: Christoph Krapp Date: Mon, 6 Jul 2020 21:05:25 +0000 (+0200) Subject: ramips: add support for TP-Link RE500 v1 X-Git-Tag: v21.02.0-rc1~2342 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=ba0f4f0cfddc6f1152273565ec35f2a0bda1e95d;p=openwrt%2Fstaging%2Fpepe2k.git ramips: add support for TP-Link RE500 v1 This device uses the same hardware as RE650 v1 which got supported in 8c51dde. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re500-v1-squashfs-factory.bin from the RE500 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Christoph Krapp [remove dts-v1 in DTSI, do not touch WiFi LEDs for RE650, keep state_default in DTS files, fix label-mac-device, use lower case for WiFi LEDs] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ramips/dts/mt7621_tplink_re500-v1.dts b/target/linux/ramips/dts/mt7621_tplink_re500-v1.dts new file mode 100644 index 0000000000..600342a822 --- /dev/null +++ b/target/linux/ramips/dts/mt7621_tplink_re500-v1.dts @@ -0,0 +1,64 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include "mt7621_tplink_rexx0-v1.dtsi" + +/ { + compatible = "tplink,re500-v1", "mediatek,mt7621-soc"; + model = "TP-Link RE500 v1"; + + aliases { + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + leds { + compatible = "gpio-leds"; + + led_power: power { + label = "re500-v1:blue:power"; + gpios = <&gpio 22 GPIO_ACTIVE_LOW>; + }; + + wifi2g { + label = "re500-v1:blue:wifi2g"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wifi5g { + label = "re500-v1:blue:wifi5g"; + gpios = <&gpio 24 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + + wps_red { + label = "re500-v1:red:wps"; + gpios = <&gpio 26 GPIO_ACTIVE_HIGH>; + }; + + wps_blue { + label = "re500-v1:blue:wps"; + gpios = <&gpio 27 GPIO_ACTIVE_HIGH>; + }; + + eth_act { + label = "re500-v1:green:eth_act"; + gpios = <&gpio 28 GPIO_ACTIVE_LOW>; + }; + + eth_link { + label = "re500-v1:green:eth_link"; + gpios = <&gpio 29 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&state_default { + gpio { + groups = "rgmii2", "wdt"; + function = "gpio"; + }; +}; diff --git a/target/linux/ramips/dts/mt7621_tplink_re650-v1.dts b/target/linux/ramips/dts/mt7621_tplink_re650-v1.dts index d5ae954189..ab8805f163 100644 --- a/target/linux/ramips/dts/mt7621_tplink_re650-v1.dts +++ b/target/linux/ramips/dts/mt7621_tplink_re650-v1.dts @@ -1,10 +1,7 @@ // SPDX-License-Identifier: GPL-2.0-or-later OR MIT /dts-v1/; -#include "mt7621.dtsi" - -#include -#include +#include "mt7621_tplink_rexx0-v1.dtsi" / { compatible = "tplink,re650-v1", "mediatek,mt7621-soc"; @@ -15,11 +12,6 @@ led-failsafe = &led_power; led-running = &led_power; led-upgrade = &led_power; - label-mac-device = &gmac0; - }; - - chosen { - bootargs = "console=ttyS0,57600"; }; leds { @@ -60,124 +52,8 @@ gpios = <&gpio 29 GPIO_ACTIVE_LOW>; }; }; - - keys { - compatible = "gpio-keys"; - - wps { - label = "wps"; - gpios = <&gpio 18 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - linux,code = ; - }; - - power { - label = "power"; - gpios = <&gpio 25 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - linux,code = ; - }; - - led { - label = "led"; - gpios = <&gpio 30 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - linux,code = ; - }; - - reset { - label = "reset"; - gpios = <&gpio 31 GPIO_ACTIVE_LOW>; - debounce-interval = <60>; - linux,code = ; - }; - }; }; -&spi0 { - status = "okay"; - - flash@0 { - compatible = "jedec,spi-nor"; - reg = <0>; - spi-max-frequency = <40000000>; - - partitions { - compatible = "fixed-partitions"; - #address-cells = <1>; - #size-cells = <1>; - - partition@0 { - label = "u-boot"; - reg = <0x0 0x20000>; - read-only; - }; - - partition@20000 { - compatible = "tplink,firmware"; - label = "firmware"; - reg = <0x20000 0xde0000>; - }; - - config: partition@e00000 { - label = "config"; - reg = <0xe00000 0x50000>; - read-only; - }; - - /* range 0xe50000 to 0xff0000 is empty in vendor - * firmware, so we do not use it either - */ - - radio: partition@ff0000 { - label = "radio"; - reg = <0xff0000 0x10000>; - read-only; - }; - }; - }; -}; - -&pcie { - status = "okay"; -}; - -&pcie0 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&radio 0x0>; - mtd-mac-address = <&config 0x10008>; - mtd-mac-address-increment = <1>; - ieee80211-freq-limit = <2400000 2500000>; - }; -}; - -&pcie1 { - wifi@0,0 { - compatible = "mediatek,mt76"; - reg = <0x0000 0 0 0 0>; - mediatek,mtd-eeprom = <&radio 0x8000>; - mtd-mac-address = <&config 0x10008>; - mtd-mac-address-increment = <2>; - ieee80211-freq-limit = <5000000 6000000>; - }; -}; - -&gmac0 { - mtd-mac-address = <&config 0x10008>; -}; - -&switch0 { - ports { - port@0 { - status = "okay"; - label = "lan"; - }; - }; -}; - - &state_default { gpio { groups = "rgmii2", "wdt"; diff --git a/target/linux/ramips/dts/mt7621_tplink_rexx0-v1.dtsi b/target/linux/ramips/dts/mt7621_tplink_rexx0-v1.dtsi new file mode 100644 index 0000000000..fa9d16a55a --- /dev/null +++ b/target/linux/ramips/dts/mt7621_tplink_rexx0-v1.dtsi @@ -0,0 +1,131 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "mt7621.dtsi" + +#include +#include + +/ { + aliases { + label-mac-device = &gmac0; + }; + + chosen { + bootargs = "console=ttyS0,57600"; + }; + + keys { + compatible = "gpio-keys"; + + wps { + label = "wps"; + gpios = <&gpio 18 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + linux,code = ; + }; + + power { + label = "power"; + gpios = <&gpio 25 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + linux,code = ; + }; + + led { + label = "led"; + gpios = <&gpio 30 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + linux,code = ; + }; + + reset { + label = "reset"; + gpios = <&gpio 31 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + linux,code = ; + }; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x20000>; + read-only; + }; + + partition@20000 { + compatible = "tplink,firmware"; + label = "firmware"; + reg = <0x20000 0xde0000>; + }; + + config: partition@e00000 { + label = "config"; + reg = <0xe00000 0x50000>; + read-only; + }; + + /* range 0xe50000 to 0xff0000 is empty in vendor + * firmware, so we do not use it either + */ + + radio: partition@ff0000 { + label = "radio"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pcie0 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&radio 0x0>; + mtd-mac-address = <&config 0x10008>; + mtd-mac-address-increment = <1>; + ieee80211-freq-limit = <2400000 2500000>; + }; +}; + +&pcie1 { + wifi@0,0 { + compatible = "mediatek,mt76"; + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&radio 0x8000>; + mtd-mac-address = <&config 0x10008>; + mtd-mac-address-increment = <2>; + ieee80211-freq-limit = <5000000 6000000>; + }; +}; + +&gmac0 { + mtd-mac-address = <&config 0x10008>; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan"; + }; + }; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index de20934598..d7a4b9fa7c 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -842,6 +842,16 @@ define Device/tplink_re350-v1 endef TARGET_DEVICES += tplink_re350-v1 +define Device/tplink_re500-v1 + $(Device/tplink-safeloader) + DEVICE_MODEL := RE500 + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-mt7615e wpad-basic + TPLINK_BOARD_ID := RE500-V1 + IMAGE_SIZE := 14208k +endef +TARGET_DEVICES += tplink_re500-v1 + define Device/tplink_re650-v1 $(Device/tplink-safeloader) DEVICE_MODEL := RE650 diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds index 716bc6e462..2e3dca7901 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/01_leds @@ -75,6 +75,10 @@ tplink,re650-v1) ucidef_set_led_netdev "eth_act" "LAN act" "$boardname:green:eth_act" "lan" "tx rx" ucidef_set_led_netdev "eth_link" "LAN link" "$boardname:green:eth_link" "lan" "link" ;; +tplink,re500-v1) + ucidef_set_led_netdev "eth_act" "LAN act" "$boardname:green:eth_act" "lan" "tx rx" + ucidef_set_led_netdev "eth_link" "LAN link" "$boardname:green:eth_link" "lan" "link" + ;; xzwifi,creativebox-v1) ucidef_set_led_netdev "internet" "internet" "$boardname:blue:internet" "wan" ;; diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 03cc921be3..a276d082e9 100755 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -37,6 +37,7 @@ ramips_setup_interfaces() netgear,ex6150|\ thunder,timecloud|\ tplink,re350-v1|\ + tplink,re500-v1|\ tplink,re650-v1|\ ubnt,unifi-nanohd) ucidef_set_interface_lan "lan" diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index a97f329a87..6cd2a45247 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -1858,6 +1858,43 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system" }, + /** Firmware layout for the RE500 */ + { + .id = "RE500-V1", + .vendor = "", + .support_list = + "SupportList:\r\n" + "{product_name:RE500,product_ver:1.0.0,special_id:00000000}\r\n" + "{product_name:RE500,product_ver:1.0.0,special_id:55530000}\r\n" + "{product_name:RE500,product_ver:1.0.0,special_id:45550000}\r\n" + "{product_name:RE500,product_ver:1.0.0,special_id:4A500000}\r\n" + "{product_name:RE500,product_ver:1.0.0,special_id:43410000}\r\n" + "{product_name:RE500,product_ver:1.0.0,special_id:41550000}\r\n" + "{product_name:RE500,product_ver:1.0.0,special_id:41530000}\r\n", + .support_trail = '\x00', + .soft_ver = NULL, + + /* We're using a dynamic kernel/rootfs split here */ + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"firmware", 0x20000, 0xde0000}, + {"partition-table", 0xe00000, 0x02000}, + {"default-mac", 0xe10000, 0x00020}, + {"pin", 0xe10100, 0x00020}, + {"product-info", 0xe11100, 0x01000}, + {"soft-version", 0xe20000, 0x01000}, + {"support-list", 0xe21000, 0x01000}, + {"profile", 0xe22000, 0x08000}, + {"user-config", 0xe30000, 0x10000}, + {"default-config", 0xe40000, 0x10000}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system" + }, + /** Firmware layout for the RE650 */ { .id = "RE650-V1",