From: Woojung Huh Date: Wed, 31 May 2017 20:19:19 +0000 (+0000) Subject: dsa: add DSA switch driver for Microchip KSZ9477 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=b987e98e50ab90e5291581204ef7a1c649313a70;p=openwrt%2Fstaging%2Fblogic.git dsa: add DSA switch driver for Microchip KSZ9477 The KSZ9477 is a fully integrated layer 2, managed, 7 ports GigE switch with numerous advanced features. 5 ports incorporate 10/100/1000 Mbps PHYs. The other 2 ports have interfaces that can be configured as SGMII, RGMII, MII or RMII. Either of these may connect directly to a host processor or to an external PHY. The SGMII port may interface to a fiber optic transceiver. This driver currently supports vlan, fdb, mdb & mirror dsa switch operations. Reviewed-by: Florian Fainelli Signed-off-by: Woojung Huh Reviewed-by: Andrew Lunn Signed-off-by: David S. Miller --- diff --git a/drivers/net/dsa/Kconfig b/drivers/net/dsa/Kconfig index 68131a45ac5e..83a9bc892a3b 100644 --- a/drivers/net/dsa/Kconfig +++ b/drivers/net/dsa/Kconfig @@ -39,6 +39,8 @@ config NET_DSA_MV88E6060 This enables support for the Marvell 88E6060 ethernet switch chip. +source "drivers/net/dsa/microchip/Kconfig" + source "drivers/net/dsa/mv88e6xxx/Kconfig" config NET_DSA_QCA8K diff --git a/drivers/net/dsa/Makefile b/drivers/net/dsa/Makefile index 9613f36083a6..4a5b5bd297ee 100644 --- a/drivers/net/dsa/Makefile +++ b/drivers/net/dsa/Makefile @@ -8,4 +8,5 @@ obj-$(CONFIG_NET_DSA_SMSC_LAN9303) += lan9303-core.o obj-$(CONFIG_NET_DSA_SMSC_LAN9303_I2C) += lan9303_i2c.o obj-$(CONFIG_NET_DSA_SMSC_LAN9303_MDIO) += lan9303_mdio.o obj-y += b53/ +obj-y += microchip/ obj-y += mv88e6xxx/ diff --git a/drivers/net/dsa/microchip/Kconfig b/drivers/net/dsa/microchip/Kconfig new file mode 100644 index 000000000000..a8b8f59099ce --- /dev/null +++ b/drivers/net/dsa/microchip/Kconfig @@ -0,0 +1,12 @@ +menuconfig MICROCHIP_KSZ + tristate "Microchip KSZ series switch support" + depends on NET_DSA + select NET_DSA_TAG_KSZ + help + This driver adds support for Microchip KSZ switch chips. + +config MICROCHIP_KSZ_SPI_DRIVER + tristate "KSZ series SPI connected switch driver" + depends on MICROCHIP_KSZ && SPI + help + Select to enable support for registering switches configured through SPI. diff --git a/drivers/net/dsa/microchip/Makefile b/drivers/net/dsa/microchip/Makefile new file mode 100644 index 000000000000..ed335e29fae8 --- /dev/null +++ b/drivers/net/dsa/microchip/Makefile @@ -0,0 +1,2 @@ +obj-$(CONFIG_MICROCHIP_KSZ) += ksz_common.o +obj-$(CONFIG_MICROCHIP_KSZ_SPI_DRIVER) += ksz_spi.o diff --git a/drivers/net/dsa/microchip/ksz_9477_reg.h b/drivers/net/dsa/microchip/ksz_9477_reg.h new file mode 100644 index 000000000000..6aa6752035a1 --- /dev/null +++ b/drivers/net/dsa/microchip/ksz_9477_reg.h @@ -0,0 +1,1676 @@ +/* + * Microchip KSZ9477 register definitions + * + * Copyright (C) 2017 + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef __KSZ9477_REGS_H +#define __KSZ9477_REGS_H + +#define KS_PRIO_M 0x7 +#define KS_PRIO_S 4 + +/* 0 - Operation */ +#define REG_CHIP_ID0__1 0x0000 + +#define REG_CHIP_ID1__1 0x0001 + +#define FAMILY_ID 0x95 +#define FAMILY_ID_94 0x94 +#define FAMILY_ID_95 0x95 +#define FAMILY_ID_85 0x85 +#define FAMILY_ID_98 0x98 +#define FAMILY_ID_88 0x88 + +#define REG_CHIP_ID2__1 0x0002 + +#define CHIP_ID_63 0x63 +#define CHIP_ID_66 0x66 +#define CHIP_ID_67 0x67 +#define CHIP_ID_77 0x77 +#define CHIP_ID_93 0x93 +#define CHIP_ID_96 0x96 +#define CHIP_ID_97 0x97 + +#define REG_CHIP_ID3__1 0x0003 + +#define SWITCH_REVISION_M 0x0F +#define SWITCH_REVISION_S 4 +#define SWITCH_RESET 0x01 + +#define REG_SW_PME_CTRL 0x0006 + +#define PME_ENABLE BIT(1) +#define PME_POLARITY BIT(0) + +#define REG_GLOBAL_OPTIONS 0x000F + +#define SW_GIGABIT_ABLE BIT(6) +#define SW_REDUNDANCY_ABLE BIT(5) +#define SW_AVB_ABLE BIT(4) +#define SW_9567_RL_5_2 0xC +#define SW_9477_SL_5_2 0xD + +#define SW_9896_GL_5_1 0xB +#define SW_9896_RL_5_1 0x8 +#define SW_9896_SL_5_1 0x9 + +#define SW_9895_GL_4_1 0x7 +#define SW_9895_RL_4_1 0x4 +#define SW_9895_SL_4_1 0x5 + +#define SW_9896_RL_4_2 0x6 + +#define SW_9893_RL_2_1 0x0 +#define SW_9893_SL_2_1 0x1 +#define SW_9893_GL_2_1 0x3 + +#define SW_QW_ABLE BIT(5) +#define SW_9893_RN_2_1 0xC + +#define REG_SW_INT_STATUS__4 0x0010 +#define REG_SW_INT_MASK__4 0x0014 + +#define LUE_INT BIT(31) +#define TRIG_TS_INT BIT(30) +#define APB_TIMEOUT_INT BIT(29) + +#define SWITCH_INT_MASK (TRIG_TS_INT | APB_TIMEOUT_INT) + +#define REG_SW_PORT_INT_STATUS__4 0x0018 +#define REG_SW_PORT_INT_MASK__4 0x001C +#define REG_SW_PHY_INT_STATUS 0x0020 +#define REG_SW_PHY_INT_ENABLE 0x0024 + +/* 1 - Global */ +#define REG_SW_GLOBAL_SERIAL_CTRL_0 0x0100 +#define SW_SPARE_REG_2 BIT(7) +#define SW_SPARE_REG_1 BIT(6) +#define SW_SPARE_REG_0 BIT(5) +#define SW_BIG_ENDIAN BIT(4) +#define SPI_AUTO_EDGE_DETECTION BIT(1) +#define SPI_CLOCK_OUT_RISING_EDGE BIT(0) + +#define REG_SW_GLOBAL_OUTPUT_CTRL__1 0x0103 +#define SW_ENABLE_REFCLKO BIT(1) +#define SW_REFCLKO_IS_125MHZ BIT(0) + +#define REG_SW_IBA__4 0x0104 + +#define SW_IBA_ENABLE BIT(31) +#define SW_IBA_DA_MATCH BIT(30) +#define SW_IBA_INIT BIT(29) +#define SW_IBA_QID_M 0xF +#define SW_IBA_QID_S 22 +#define SW_IBA_PORT_M 0x2F +#define SW_IBA_PORT_S 16 +#define SW_IBA_FRAME_TPID_M 0xFFFF + +#define REG_SW_APB_TIMEOUT_ADDR__4 0x0108 + +#define APB_TIMEOUT_ACKNOWLEDGE BIT(31) + +#define REG_SW_IBA_SYNC__1 0x010C + +#define REG_SW_IO_STRENGTH__1 0x010D +#define SW_DRIVE_STRENGTH_M 0x7 +#define SW_DRIVE_STRENGTH_2MA 0 +#define SW_DRIVE_STRENGTH_4MA 1 +#define SW_DRIVE_STRENGTH_8MA 2 +#define SW_DRIVE_STRENGTH_12MA 3 +#define SW_DRIVE_STRENGTH_16MA 4 +#define SW_DRIVE_STRENGTH_20MA 5 +#define SW_DRIVE_STRENGTH_24MA 6 +#define SW_DRIVE_STRENGTH_28MA 7 +#define SW_HI_SPEED_DRIVE_STRENGTH_S 4 +#define SW_LO_SPEED_DRIVE_STRENGTH_S 0 + +#define REG_SW_IBA_STATUS__4 0x0110 + +#define SW_IBA_REQ BIT(31) +#define SW_IBA_RESP BIT(30) +#define SW_IBA_DA_MISMATCH BIT(14) +#define SW_IBA_FMT_MISMATCH BIT(13) +#define SW_IBA_CODE_ERROR BIT(12) +#define SW_IBA_CMD_ERROR BIT(11) +#define SW_IBA_CMD_LOC_M (BIT(6) - 1) + +#define REG_SW_IBA_STATES__4 0x0114 + +#define SW_IBA_BUF_STATE_S 30 +#define SW_IBA_CMD_STATE_S 28 +#define SW_IBA_RESP_STATE_S 26 +#define SW_IBA_STATE_M 0x3 +#define SW_IBA_PACKET_SIZE_M 0x7F +#define SW_IBA_PACKET_SIZE_S 16 +#define SW_IBA_FMT_ID_M 0xFFFF + +#define REG_SW_IBA_RESULT__4 0x0118 + +#define SW_IBA_SIZE_S 24 + +#define SW_IBA_RETRY_CNT_M (BIT(5) - 1) + +/* 2 - PHY */ +#define REG_SW_POWER_MANAGEMENT_CTRL 0x0201 + +#define SW_PLL_POWER_DOWN BIT(5) +#define SW_POWER_DOWN_MODE 0x3 +#define SW_ENERGY_DETECTION 1 +#define SW_SOFT_POWER_DOWN 2 +#define SW_POWER_SAVING 3 + +/* 3 - Operation Control */ +#define REG_SW_OPERATION 0x0300 + +#define SW_DOUBLE_TAG BIT(7) +#define SW_RESET BIT(1) +#define SW_START BIT(0) + +#define REG_SW_MAC_ADDR_0 0x0302 +#define REG_SW_MAC_ADDR_1 0x0303 +#define REG_SW_MAC_ADDR_2 0x0304 +#define REG_SW_MAC_ADDR_3 0x0305 +#define REG_SW_MAC_ADDR_4 0x0306 +#define REG_SW_MAC_ADDR_5 0x0307 + +#define REG_SW_MTU__2 0x0308 + +#define REG_SW_ISP_TPID__2 0x030A + +#define REG_SW_HSR_TPID__2 0x030C + +#define REG_AVB_STRATEGY__2 0x030E + +#define SW_SHAPING_CREDIT_ACCT BIT(1) +#define SW_POLICING_CREDIT_ACCT BIT(0) + +#define REG_SW_LUE_CTRL_0 0x0310 + +#define SW_VLAN_ENABLE BIT(7) +#define SW_DROP_INVALID_VID BIT(6) +#define SW_AGE_CNT_M 0x7 +#define SW_AGE_CNT_S 3 +#define SW_RESV_MCAST_ENABLE BIT(2) +#define SW_HASH_OPTION_M 0x03 +#define SW_HASH_OPTION_CRC 1 +#define SW_HASH_OPTION_XOR 2 +#define SW_HASH_OPTION_DIRECT 3 + +#define REG_SW_LUE_CTRL_1 0x0311 + +#define UNICAST_LEARN_DISABLE BIT(7) +#define SW_SRC_ADDR_FILTER BIT(6) +#define SW_FLUSH_STP_TABLE BIT(5) +#define SW_FLUSH_MSTP_TABLE BIT(4) +#define SW_FWD_MCAST_SRC_ADDR BIT(3) +#define SW_AGING_ENABLE BIT(2) +#define SW_FAST_AGING BIT(1) +#define SW_LINK_AUTO_AGING BIT(0) + +#define REG_SW_LUE_CTRL_2 0x0312 + +#define SW_TRAP_DOUBLE_TAG BIT(6) +#define SW_EGRESS_VLAN_FILTER_DYN BIT(5) +#define SW_EGRESS_VLAN_FILTER_STA BIT(4) +#define SW_FLUSH_OPTION_M 0x3 +#define SW_FLUSH_OPTION_S 2 +#define SW_FLUSH_OPTION_DYN_MAC 1 +#define SW_FLUSH_OPTION_STA_MAC 2 +#define SW_FLUSH_OPTION_BOTH 3 +#define SW_PRIO_M 0x3 +#define SW_PRIO_DA 0 +#define SW_PRIO_SA 1 +#define SW_PRIO_HIGHEST_DA_SA 2 +#define SW_PRIO_LOWEST_DA_SA 3 + +#define REG_SW_LUE_CTRL_3 0x0313 + +#define REG_SW_LUE_INT_STATUS 0x0314 +#define REG_SW_LUE_INT_ENABLE 0x0315 + +#define LEARN_FAIL_INT BIT(2) +#define ALMOST_FULL_INT BIT(1) +#define WRITE_FAIL_INT BIT(0) + +#define REG_SW_LUE_INDEX_0__2 0x0316 + +#define ENTRY_INDEX_M 0x0FFF + +#define REG_SW_LUE_INDEX_1__2 0x0318 + +#define FAIL_INDEX_M 0x03FF + +#define REG_SW_LUE_INDEX_2__2 0x031A + +#define REG_SW_LUE_UNK_UCAST_CTRL__4 0x0320 + +#define SW_UNK_UCAST_ENABLE BIT(31) + +#define REG_SW_LUE_UNK_MCAST_CTRL__4 0x0324 + +#define SW_UNK_MCAST_ENABLE BIT(31) + +#define REG_SW_LUE_UNK_VID_CTRL__4 0x0328 + +#define SW_UNK_VID_ENABLE BIT(31) + +#define REG_SW_MAC_CTRL_0 0x0330 + +#define SW_NEW_BACKOFF BIT(7) +#define SW_CHECK_LENGTH BIT(3) +#define SW_PAUSE_UNH_MODE BIT(1) +#define SW_AGGR_BACKOFF BIT(0) + +#define REG_SW_MAC_CTRL_1 0x0331 + +#define MULTICAST_STORM_DISABLE BIT(6) +#define SW_BACK_PRESSURE BIT(5) +#define FAIR_FLOW_CTRL BIT(4) +#define NO_EXC_COLLISION_DROP BIT(3) +#define SW_JUMBO_PACKET BIT(2) +#define SW_LEGAL_PACKET_DISABLE BIT(1) +#define SW_PASS_SHORT_FRAME BIT(0) + +#define REG_SW_MAC_CTRL_2 0x0332 + +#define SW_REPLACE_VID BIT(3) +#define BROADCAST_STORM_RATE_HI 0x07 + +#define REG_SW_MAC_CTRL_3 0x0333 + +#define BROADCAST_STORM_RATE_LO 0xFF +#define BROADCAST_STORM_RATE 0x07FF + +#define REG_SW_MAC_CTRL_4 0x0334 + +#define SW_PASS_PAUSE BIT(3) + +#define REG_SW_MAC_CTRL_5 0x0335 + +#define SW_OUT_RATE_LIMIT_QUEUE_BASED BIT(3) + +#define REG_SW_MAC_CTRL_6 0x0336 + +#define SW_MIB_COUNTER_FLUSH BIT(7) +#define SW_MIB_COUNTER_FREEZE BIT(6) + +#define REG_SW_MAC_802_1P_MAP_0 0x0338 +#define REG_SW_MAC_802_1P_MAP_1 0x0339 +#define REG_SW_MAC_802_1P_MAP_2 0x033A +#define REG_SW_MAC_802_1P_MAP_3 0x033B + +#define SW_802_1P_MAP_M KS_PRIO_M +#define SW_802_1P_MAP_S KS_PRIO_S + +#define REG_SW_MAC_ISP_CTRL 0x033C + +#define REG_SW_MAC_TOS_CTRL 0x033E + +#define SW_TOS_DSCP_REMARK BIT(1) +#define SW_TOS_DSCP_REMAP BIT(0) + +#define REG_SW_MAC_TOS_PRIO_0 0x0340 +#define REG_SW_MAC_TOS_PRIO_1 0x0341 +#define REG_SW_MAC_TOS_PRIO_2 0x0342 +#define REG_SW_MAC_TOS_PRIO_3 0x0343 +#define REG_SW_MAC_TOS_PRIO_4 0x0344 +#define REG_SW_MAC_TOS_PRIO_5 0x0345 +#define REG_SW_MAC_TOS_PRIO_6 0x0346 +#define REG_SW_MAC_TOS_PRIO_7 0x0347 +#define REG_SW_MAC_TOS_PRIO_8 0x0348 +#define REG_SW_MAC_TOS_PRIO_9 0x0349 +#define REG_SW_MAC_TOS_PRIO_10 0x034A +#define REG_SW_MAC_TOS_PRIO_11 0x034B +#define REG_SW_MAC_TOS_PRIO_12 0x034C +#define REG_SW_MAC_TOS_PRIO_13 0x034D +#define REG_SW_MAC_TOS_PRIO_14 0x034E +#define REG_SW_MAC_TOS_PRIO_15 0x034F +#define REG_SW_MAC_TOS_PRIO_16 0x0350 +#define REG_SW_MAC_TOS_PRIO_17 0x0351 +#define REG_SW_MAC_TOS_PRIO_18 0x0352 +#define REG_SW_MAC_TOS_PRIO_19 0x0353 +#define REG_SW_MAC_TOS_PRIO_20 0x0354 +#define REG_SW_MAC_TOS_PRIO_21 0x0355 +#define REG_SW_MAC_TOS_PRIO_22 0x0356 +#define REG_SW_MAC_TOS_PRIO_23 0x0357 +#define REG_SW_MAC_TOS_PRIO_24 0x0358 +#define REG_SW_MAC_TOS_PRIO_25 0x0359 +#define REG_SW_MAC_TOS_PRIO_26 0x035A +#define REG_SW_MAC_TOS_PRIO_27 0x035B +#define REG_SW_MAC_TOS_PRIO_28 0x035C +#define REG_SW_MAC_TOS_PRIO_29 0x035D +#define REG_SW_MAC_TOS_PRIO_30 0x035E +#define REG_SW_MAC_TOS_PRIO_31 0x035F + +#define REG_SW_MRI_CTRL_0 0x0370 + +#define SW_IGMP_SNOOP BIT(6) +#define SW_IPV6_MLD_OPTION BIT(3) +#define SW_IPV6_MLD_SNOOP BIT(2) +#define SW_MIRROR_RX_TX BIT(0) + +#define REG_SW_CLASS_D_IP_CTRL__4 0x0374 + +#define SW_CLASS_D_IP_ENABLE BIT(31) + +#define REG_SW_MRI_CTRL_8 0x0378 + +#define SW_NO_COLOR_S 6 +#define SW_RED_COLOR_S 4 +#define SW_YELLOW_COLOR_S 2 +#define SW_GREEN_COLOR_S 0 +#define SW_COLOR_M 0x3 + +#define REG_SW_QM_CTRL__4 0x0390 + +#define PRIO_SCHEME_SELECT_M KS_PRIO_M +#define PRIO_SCHEME_SELECT_S 6 +#define PRIO_MAP_3_HI 0 +#define PRIO_MAP_2_HI 2 +#define PRIO_MAP_0_LO 3 +#define UNICAST_VLAN_BOUNDARY BIT(1) + +#define REG_SW_EEE_QM_CTRL__2 0x03C0 + +#define REG_SW_EEE_TXQ_WAIT_TIME__2 0x03C2 + +/* 4 - */ +#define REG_SW_VLAN_ENTRY__4 0x0400 + +#define VLAN_VALID BIT(31) +#define VLAN_FORWARD_OPTION BIT(27) +#define VLAN_PRIO_M KS_PRIO_M +#define VLAN_PRIO_S 24 +#define VLAN_MSTP_M 0x7 +#define VLAN_MSTP_S 12 +#define VLAN_FID_M 0x7F + +#define REG_SW_VLAN_ENTRY_UNTAG__4 0x0404 +#define REG_SW_VLAN_ENTRY_PORTS__4 0x0408 + +#define REG_SW_VLAN_ENTRY_INDEX__2 0x040C + +#define VLAN_INDEX_M 0x0FFF + +#define REG_SW_VLAN_CTRL 0x040E + +#define VLAN_START BIT(7) +#define VLAN_ACTION 0x3 +#define VLAN_WRITE 1 +#define VLAN_READ 2 +#define VLAN_CLEAR 3 + +#define REG_SW_ALU_INDEX_0 0x0410 + +#define ALU_FID_INDEX_S 16 +#define ALU_MAC_ADDR_HI 0xFFFF + +#define REG_SW_ALU_INDEX_1 0x0414 + +#define ALU_DIRECT_INDEX_M (BIT(12) - 1) + +#define REG_SW_ALU_CTRL__4 0x0418 + +#define ALU_VALID_CNT_M (BIT(14) - 1) +#define ALU_VALID_CNT_S 16 +#define ALU_START BIT(7) +#define ALU_VALID BIT(6) +#define ALU_DIRECT BIT(2) +#define ALU_ACTION 0x3 +#define ALU_WRITE 1 +#define ALU_READ 2 +#define ALU_SEARCH 3 + +#define REG_SW_ALU_STAT_CTRL__4 0x041C + +#define ALU_STAT_INDEX_M (BIT(4) - 1) +#define ALU_STAT_INDEX_S 16 +#define ALU_RESV_MCAST_INDEX_M (BIT(6) - 1) +#define ALU_STAT_START BIT(7) +#define ALU_RESV_MCAST_ADDR BIT(1) +#define ALU_STAT_READ BIT(0) + +#define REG_SW_ALU_VAL_A 0x0420 + +#define ALU_V_STATIC_VALID BIT(31) +#define ALU_V_SRC_FILTER BIT(30) +#define ALU_V_DST_FILTER BIT(29) +#define ALU_V_PRIO_AGE_CNT_M (BIT(3) - 1) +#define ALU_V_PRIO_AGE_CNT_S 26 +#define ALU_V_MSTP_M 0x7 + +#define REG_SW_ALU_VAL_B 0x0424 + +#define ALU_V_OVERRIDE BIT(31) +#define ALU_V_USE_FID BIT(30) +#define ALU_V_PORT_MAP (BIT(24) - 1) + +#define REG_SW_ALU_VAL_C 0x0428 + +#define ALU_V_FID_M (BIT(16) - 1) +#define ALU_V_FID_S 16 +#define ALU_V_MAC_ADDR_HI 0xFFFF + +#define REG_SW_ALU_VAL_D 0x042C + +#define REG_HSR_ALU_INDEX_0 0x0440 + +#define REG_HSR_ALU_INDEX_1 0x0444 + +#define HSR_DST_MAC_INDEX_LO_S 16 +#define HSR_SRC_MAC_INDEX_HI 0xFFFF + +#define REG_HSR_ALU_INDEX_2 0x0448 + +#define HSR_INDEX_MAX BIT(9) +#define HSR_DIRECT_INDEX_M (HSR_INDEX_MAX - 1) + +#define REG_HSR_ALU_INDEX_3 0x044C + +#define HSR_PATH_INDEX_M (BIT(4) - 1) + +#define REG_HSR_ALU_CTRL__4 0x0450 + +#define HSR_VALID_CNT_M (BIT(14) - 1) +#define HSR_VALID_CNT_S 16 +#define HSR_START BIT(7) +#define HSR_VALID BIT(6) +#define HSR_SEARCH_END BIT(5) +#define HSR_DIRECT BIT(2) +#define HSR_ACTION 0x3 +#define HSR_WRITE 1 +#define HSR_READ 2 +#define HSR_SEARCH 3 + +#define REG_HSR_ALU_VAL_A 0x0454 + +#define HSR_V_STATIC_VALID BIT(31) +#define HSR_V_AGE_CNT_M (BIT(3) - 1) +#define HSR_V_AGE_CNT_S 26 +#define HSR_V_PATH_ID_M (BIT(4) - 1) + +#define REG_HSR_ALU_VAL_B 0x0458 + +#define REG_HSR_ALU_VAL_C 0x045C + +#define HSR_V_DST_MAC_ADDR_LO_S 16 +#define HSR_V_SRC_MAC_ADDR_HI 0xFFFF + +#define REG_HSR_ALU_VAL_D 0x0460 + +#define REG_HSR_ALU_VAL_E 0x0464 + +#define HSR_V_START_SEQ_1_S 16 +#define HSR_V_START_SEQ_2_S 0 + +#define REG_HSR_ALU_VAL_F 0x0468 + +#define HSR_V_EXP_SEQ_1_S 16 +#define HSR_V_EXP_SEQ_2_S 0 + +#define REG_HSR_ALU_VAL_G 0x046C + +#define HSR_V_SEQ_CNT_1_S 16 +#define HSR_V_SEQ_CNT_2_S 0 + +#define HSR_V_SEQ_M (BIT(16) - 1) + +/* 5 - PTP Clock */ +#define REG_PTP_CLK_CTRL 0x0500 + +#define PTP_STEP_ADJ BIT(6) +#define PTP_STEP_DIR BIT(5) +#define PTP_READ_TIME BIT(4) +#define PTP_LOAD_TIME BIT(3) +#define PTP_CLK_ADJ_ENABLE BIT(2) +#define PTP_CLK_ENABLE BIT(1) +#define PTP_CLK_RESET BIT(0) + +#define REG_PTP_RTC_SUB_NANOSEC__2 0x0502 + +#define PTP_RTC_SUB_NANOSEC_M 0x0007 + +#define REG_PTP_RTC_NANOSEC 0x0504 +#define REG_PTP_RTC_NANOSEC_H 0x0504 +#define REG_PTP_RTC_NANOSEC_L 0x0506 + +#define REG_PTP_RTC_SEC 0x0508 +#define REG_PTP_RTC_SEC_H 0x0508 +#define REG_PTP_RTC_SEC_L 0x050A + +#define REG_PTP_SUBNANOSEC_RATE 0x050C +#define REG_PTP_SUBNANOSEC_RATE_H 0x050C + +#define PTP_RATE_DIR BIT(31) +#define PTP_TMP_RATE_ENABLE BIT(30) + +#define REG_PTP_SUBNANOSEC_RATE_L 0x050E + +#define REG_PTP_RATE_DURATION 0x0510 +#define REG_PTP_RATE_DURATION_H 0x0510 +#define REG_PTP_RATE_DURATION_L 0x0512 + +#define REG_PTP_MSG_CONF1 0x0514 + +#define PTP_802_1AS BIT(7) +#define PTP_ENABLE BIT(6) +#define PTP_ETH_ENABLE BIT(5) +#define PTP_IPV4_UDP_ENABLE BIT(4) +#define PTP_IPV6_UDP_ENABLE BIT(3) +#define PTP_TC_P2P BIT(2) +#define PTP_MASTER BIT(1) +#define PTP_1STEP BIT(0) + +#define REG_PTP_MSG_CONF2 0x0516 + +#define PTP_UNICAST_ENABLE BIT(12) +#define PTP_ALTERNATE_MASTER BIT(11) +#define PTP_ALL_HIGH_PRIO BIT(10) +#define PTP_SYNC_CHECK BIT(9) +#define PTP_DELAY_CHECK BIT(8) +#define PTP_PDELAY_CHECK BIT(7) +#define PTP_DROP_SYNC_DELAY_REQ BIT(5) +#define PTP_DOMAIN_CHECK BIT(4) +#define PTP_UDP_CHECKSUM BIT(2) + +#define REG_PTP_DOMAIN_VERSION 0x0518 +#define PTP_VERSION_M 0xFF00 +#define PTP_DOMAIN_M 0x00FF + +#define REG_PTP_UNIT_INDEX__4 0x0520 + +#define PTP_UNIT_M 0xF + +#define PTP_GPIO_INDEX_S 16 +#define PTP_TSI_INDEX_S 8 +#define PTP_TOU_INDEX_S 0 + +#define REG_PTP_TRIG_STATUS__4 0x0524 + +#define TRIG_ERROR_S 16 +#define TRIG_DONE_S 0 + +#define REG_PTP_INT_STATUS__4 0x0528 + +#define TRIG_INT_S 16 +#define TS_INT_S 0 + +#define TRIG_UNIT_M 0x7 +#define TS_UNIT_M 0x3 + +#define REG_PTP_CTRL_STAT__4 0x052C + +#define GPIO_IN BIT(7) +#define GPIO_OUT BIT(6) +#define TS_INT_ENABLE BIT(5) +#define TRIG_ACTIVE BIT(4) +#define TRIG_ENABLE BIT(3) +#define TRIG_RESET BIT(2) +#define TS_ENABLE BIT(1) +#define TS_RESET BIT(0) + +#define GPIO_CTRL_M (GPIO_IN | GPIO_OUT) + +#define TRIG_CTRL_M \ + (TRIG_ACTIVE | TRIG_ENABLE | TRIG_RESET) + +#define TS_CTRL_M \ + (TS_INT_ENABLE | TS_ENABLE | TS_RESET) + +#define REG_TRIG_TARGET_NANOSEC 0x0530 +#define REG_TRIG_TARGET_SEC 0x0534 + +#define REG_TRIG_CTRL__4 0x0538 + +#define TRIG_CASCADE_ENABLE BIT(31) +#define TRIG_CASCADE_TAIL BIT(30) +#define TRIG_CASCADE_UPS_M 0xF +#define TRIG_CASCADE_UPS_S 26 +#define TRIG_NOW BIT(25) +#define TRIG_NOTIFY BIT(24) +#define TRIG_EDGE BIT(23) +#define TRIG_PATTERN_S 20 +#define TRIG_PATTERN_M 0x7 +#define TRIG_NEG_EDGE 0 +#define TRIG_POS_EDGE 1 +#define TRIG_NEG_PULSE 2 +#define TRIG_POS_PULSE 3 +#define TRIG_NEG_PERIOD 4 +#define TRIG_POS_PERIOD 5 +#define TRIG_REG_OUTPUT 6 +#define TRIG_GPO_S 16 +#define TRIG_GPO_M 0xF +#define TRIG_CASCADE_ITERATE_CNT_M 0xFFFF + +#define REG_TRIG_CYCLE_WIDTH 0x053C + +#define REG_TRIG_CYCLE_CNT 0x0540 + +#define TRIG_CYCLE_CNT_M 0xFFFF +#define TRIG_CYCLE_CNT_S 16 +#define TRIG_BIT_PATTERN_M 0xFFFF + +#define REG_TRIG_ITERATE_TIME 0x0544 + +#define REG_TRIG_PULSE_WIDTH__4 0x0548 + +#define TRIG_PULSE_WIDTH_M 0x00FFFFFF + +#define REG_TS_CTRL_STAT__4 0x0550 + +#define TS_EVENT_DETECT_M 0xF +#define TS_EVENT_DETECT_S 17 +#define TS_EVENT_OVERFLOW BIT(16) +#define TS_GPI_M 0xF +#define TS_GPI_S 8 +#define TS_DETECT_RISE BIT(7) +#define TS_DETECT_FALL BIT(6) +#define TS_DETECT_S 6 +#define TS_CASCADE_TAIL BIT(5) +#define TS_CASCADE_UPS_M 0xF +#define TS_CASCADE_UPS_S 1 +#define TS_CASCADE_ENABLE BIT(0) + +#define DETECT_RISE (TS_DETECT_RISE >> TS_DETECT_S) +#define DETECT_FALL (TS_DETECT_FALL >> TS_DETECT_S) + +#define REG_TS_EVENT_0_NANOSEC 0x0554 +#define REG_TS_EVENT_0_SEC 0x0558 +#define REG_TS_EVENT_0_SUB_NANOSEC 0x055C + +#define REG_TS_EVENT_1_NANOSEC 0x0560 +#define REG_TS_EVENT_1_SEC 0x0564 +#define REG_TS_EVENT_1_SUB_NANOSEC 0x0568 + +#define REG_TS_EVENT_2_NANOSEC 0x056C +#define REG_TS_EVENT_2_SEC 0x0570 +#define REG_TS_EVENT_2_SUB_NANOSEC 0x0574 + +#define REG_TS_EVENT_3_NANOSEC 0x0578 +#define REG_TS_EVENT_3_SEC 0x057C +#define REG_TS_EVENT_3_SUB_NANOSEC 0x0580 + +#define REG_TS_EVENT_4_NANOSEC 0x0584 +#define REG_TS_EVENT_4_SEC 0x0588 +#define REG_TS_EVENT_4_SUB_NANOSEC 0x058C + +#define REG_TS_EVENT_5_NANOSEC 0x0590 +#define REG_TS_EVENT_5_SEC 0x0594 +#define REG_TS_EVENT_5_SUB_NANOSEC 0x0598 + +#define REG_TS_EVENT_6_NANOSEC 0x059C +#define REG_TS_EVENT_6_SEC 0x05A0 +#define REG_TS_EVENT_6_SUB_NANOSEC 0x05A4 + +#define REG_TS_EVENT_7_NANOSEC 0x05A8 +#define REG_TS_EVENT_7_SEC 0x05AC +#define REG_TS_EVENT_7_SUB_NANOSEC 0x05B0 + +#define TS_EVENT_EDGE_M 0x1 +#define TS_EVENT_EDGE_S 30 +#define TS_EVENT_NANOSEC_M (BIT(30) - 1) + +#define TS_EVENT_SUB_NANOSEC_M 0x7 + +#define TS_EVENT_SAMPLE \ + (REG_TS_EVENT_1_NANOSEC - REG_TS_EVENT_0_NANOSEC) + +#define PORT_CTRL_ADDR(port, addr) ((addr) | (((port) + 1) << 12)) + +#define REG_GLOBAL_RR_INDEX__1 0x0600 + +/* DLR */ +#define REG_DLR_SRC_PORT__4 0x0604 + +#define DLR_SRC_PORT_UNICAST BIT(31) +#define DLR_SRC_PORT_M 0x3 +#define DLR_SRC_PORT_BOTH 0 +#define DLR_SRC_PORT_EACH 1 + +#define REG_DLR_IP_ADDR__4 0x0608 + +#define REG_DLR_CTRL__1 0x0610 + +#define DLR_RESET_SEQ_ID BIT(3) +#define DLR_BACKUP_AUTO_ON BIT(2) +#define DLR_BEACON_TX_ENABLE BIT(1) +#define DLR_ASSIST_ENABLE BIT(0) + +#define REG_DLR_STATE__1 0x0611 + +#define DLR_NODE_STATE_M 0x3 +#define DLR_NODE_STATE_S 1 +#define DLR_NODE_STATE_IDLE 0 +#define DLR_NODE_STATE_FAULT 1 +#define DLR_NODE_STATE_NORMAL 2 +#define DLR_RING_STATE_FAULT 0 +#define DLR_RING_STATE_NORMAL 1 + +#define REG_DLR_PRECEDENCE__1 0x0612 + +#define REG_DLR_BEACON_INTERVAL__4 0x0614 + +#define REG_DLR_BEACON_TIMEOUT__4 0x0618 + +#define REG_DLR_TIMEOUT_WINDOW__4 0x061C + +#define DLR_TIMEOUT_WINDOW_M (BIT(22) - 1) + +#define REG_DLR_VLAN_ID__2 0x0620 + +#define DLR_VLAN_ID_M (BIT(12) - 1) + +#define REG_DLR_DEST_ADDR_0 0x0622 +#define REG_DLR_DEST_ADDR_1 0x0623 +#define REG_DLR_DEST_ADDR_2 0x0624 +#define REG_DLR_DEST_ADDR_3 0x0625 +#define REG_DLR_DEST_ADDR_4 0x0626 +#define REG_DLR_DEST_ADDR_5 0x0627 + +#define REG_DLR_PORT_MAP__4 0x0628 + +#define REG_DLR_CLASS__1 0x062C + +#define DLR_FRAME_QID_M 0x3 + +/* HSR */ +#define REG_HSR_PORT_MAP__4 0x0640 + +#define REG_HSR_ALU_CTRL_0__1 0x0644 + +#define HSR_DUPLICATE_DISCARD BIT(7) +#define HSR_NODE_UNICAST BIT(6) +#define HSR_AGE_CNT_DEFAULT_M 0x7 +#define HSR_AGE_CNT_DEFAULT_S 3 +#define HSR_LEARN_MCAST_DISABLE BIT(2) +#define HSR_HASH_OPTION_M 0x3 +#define HSR_HASH_DISABLE 0 +#define HSR_HASH_UPPER_BITS 1 +#define HSR_HASH_LOWER_BITS 2 +#define HSR_HASH_XOR_BOTH_BITS 3 + +#define REG_HSR_ALU_CTRL_1__1 0x0645 + +#define HSR_LEARN_UCAST_DISABLE BIT(7) +#define HSR_FLUSH_TABLE BIT(5) +#define HSR_PROC_MCAST_SRC BIT(3) +#define HSR_AGING_ENABLE BIT(2) + +#define REG_HSR_ALU_CTRL_2__2 0x0646 + +#define REG_HSR_ALU_AGE_PERIOD__4 0x0648 + +#define REG_HSR_ALU_INT_STATUS__1 0x064C +#define REG_HSR_ALU_INT_MASK__1 0x064D + +#define HSR_WINDOW_OVERFLOW_INT BIT(3) +#define HSR_LEARN_FAIL_INT BIT(2) +#define HSR_ALMOST_FULL_INT BIT(1) +#define HSR_WRITE_FAIL_INT BIT(0) + +#define REG_HSR_ALU_ENTRY_0__2 0x0650 + +#define HSR_ENTRY_INDEX_M (BIT(10) - 1) +#define HSR_FAIL_INDEX_M (BIT(8) - 1) + +#define REG_HSR_ALU_ENTRY_1__2 0x0652 + +#define HSR_FAIL_LEARN_INDEX_M (BIT(8) - 1) + +#define REG_HSR_ALU_ENTRY_3__2 0x0654 + +#define HSR_CPU_ACCESS_ENTRY_INDEX_M (BIT(8) - 1) + +/* 0 - Operation */ +#define REG_PORT_DEFAULT_VID 0x0000 + +#define REG_PORT_CUSTOM_VID 0x0002 +#define REG_PORT_AVB_SR_1_VID 0x0004 +#define REG_PORT_AVB_SR_2_VID 0x0006 + +#define REG_PORT_AVB_SR_1_TYPE 0x0008 +#define REG_PORT_AVB_SR_2_TYPE 0x000A + +#define REG_PORT_PME_STATUS 0x0013 +#define REG_PORT_PME_CTRL 0x0017 + +#define PME_WOL_MAGICPKT BIT(2) +#define PME_WOL_LINKUP BIT(1) +#define PME_WOL_ENERGY BIT(0) + +#define REG_PORT_INT_STATUS 0x001B +#define REG_PORT_INT_MASK 0x001F + +#define PORT_SGMII_INT BIT(3) +#define PORT_PTP_INT BIT(2) +#define PORT_PHY_INT BIT(1) +#define PORT_ACL_INT BIT(0) + +#define PORT_INT_MASK \ + (PORT_SGMII_INT | PORT_PTP_INT | PORT_PHY_INT | PORT_ACL_INT) + +#define REG_PORT_CTRL_0 0x0020 + +#define PORT_MAC_LOOPBACK BIT(7) +#define PORT_FORCE_TX_FLOW_CTRL BIT(4) +#define PORT_FORCE_RX_FLOW_CTRL BIT(3) +#define PORT_TAIL_TAG_ENABLE BIT(2) +#define PORT_QUEUE_SPLIT_ENABLE 0x3 + +#define REG_PORT_CTRL_1 0x0021 + +#define PORT_SRP_ENABLE 0x3 + +#define REG_PORT_STATUS_0 0x0030 + +#define PORT_INTF_SPEED_M 0x3 +#define PORT_INTF_SPEED_S 3 +#define PORT_INTF_FULL_DUPLEX BIT(2) +#define PORT_TX_FLOW_CTRL BIT(1) +#define PORT_RX_FLOW_CTRL BIT(0) + +#define REG_PORT_STATUS_1 0x0034 + +/* 1 - PHY */ +#define REG_PORT_PHY_CTRL 0x0100 + +#define PORT_PHY_RESET BIT(15) +#define PORT_PHY_LOOPBACK BIT(14) +#define PORT_SPEED_100MBIT BIT(13) +#define PORT_AUTO_NEG_ENABLE BIT(12) +#define PORT_POWER_DOWN BIT(11) +#define PORT_ISOLATE BIT(10) +#define PORT_AUTO_NEG_RESTART BIT(9) +#define PORT_FULL_DUPLEX BIT(8) +#define PORT_COLLISION_TEST BIT(7) +#define PORT_SPEED_1000MBIT BIT(6) + +#define REG_PORT_PHY_STATUS 0x0102 + +#define PORT_100BT4_CAPABLE BIT(15) +#define PORT_100BTX_FD_CAPABLE BIT(14) +#define PORT_100BTX_CAPABLE BIT(13) +#define PORT_10BT_FD_CAPABLE BIT(12) +#define PORT_10BT_CAPABLE BIT(11) +#define PORT_EXTENDED_STATUS BIT(8) +#define PORT_MII_SUPPRESS_CAPABLE BIT(6) +#define PORT_AUTO_NEG_ACKNOWLEDGE BIT(5) +#define PORT_REMOTE_FAULT BIT(4) +#define PORT_AUTO_NEG_CAPABLE BIT(3) +#define PORT_LINK_STATUS BIT(2) +#define PORT_JABBER_DETECT BIT(1) +#define PORT_EXTENDED_CAPABILITY BIT(0) + +#define REG_PORT_PHY_ID_HI 0x0104 +#define REG_PORT_PHY_ID_LO 0x0106 + +#define KSZ9477_ID_HI 0x0022 +#define KSZ9477_ID_LO 0x1622 + +#define REG_PORT_PHY_AUTO_NEGOTIATION 0x0108 + +#define PORT_AUTO_NEG_NEXT_PAGE BIT(15) +#define PORT_AUTO_NEG_REMOTE_FAULT BIT(13) +#define PORT_AUTO_NEG_ASYM_PAUSE BIT(11) +#define PORT_AUTO_NEG_SYM_PAUSE BIT(10) +#define PORT_AUTO_NEG_100BT4 BIT(9) +#define PORT_AUTO_NEG_100BTX_FD BIT(8) +#define PORT_AUTO_NEG_100BTX BIT(7) +#define PORT_AUTO_NEG_10BT_FD BIT(6) +#define PORT_AUTO_NEG_10BT BIT(5) +#define PORT_AUTO_NEG_SELECTOR 0x001F +#define PORT_AUTO_NEG_802_3 0x0001 + +#define PORT_AUTO_NEG_PAUSE \ + (PORT_AUTO_NEG_ASYM_PAUSE | PORT_AUTO_NEG_SYM_PAUSE) + +#define REG_PORT_PHY_REMOTE_CAPABILITY 0x010A + +#define PORT_REMOTE_NEXT_PAGE BIT(15) +#define PORT_REMOTE_ACKNOWLEDGE BIT(14) +#define PORT_REMOTE_REMOTE_FAULT BIT(13) +#define PORT_REMOTE_ASYM_PAUSE BIT(11) +#define PORT_REMOTE_SYM_PAUSE BIT(10) +#define PORT_REMOTE_100BTX_FD BIT(8) +#define PORT_REMOTE_100BTX BIT(7) +#define PORT_REMOTE_10BT_FD BIT(6) +#define PORT_REMOTE_10BT BIT(5) + +#define REG_PORT_PHY_1000_CTRL 0x0112 + +#define PORT_AUTO_NEG_MANUAL BIT(12) +#define PORT_AUTO_NEG_MASTER BIT(11) +#define PORT_AUTO_NEG_MASTER_PREFERRED BIT(10) +#define PORT_AUTO_NEG_1000BT_FD BIT(9) +#define PORT_AUTO_NEG_1000BT BIT(8) + +#define REG_PORT_PHY_1000_STATUS 0x0114 + +#define PORT_MASTER_FAULT BIT(15) +#define PORT_LOCAL_MASTER BIT(14) +#define PORT_LOCAL_RX_OK BIT(13) +#define PORT_REMOTE_RX_OK BIT(12) +#define PORT_REMOTE_1000BT_FD BIT(11) +#define PORT_REMOTE_1000BT BIT(10) +#define PORT_REMOTE_IDLE_CNT_M 0x0F + +#define PORT_PHY_1000_STATIC_STATUS \ + (PORT_LOCAL_RX_OK | \ + PORT_REMOTE_RX_OK | \ + PORT_REMOTE_1000BT_FD | \ + PORT_REMOTE_1000BT) + +#define REG_PORT_PHY_MMD_SETUP 0x011A + +#define PORT_MMD_OP_MODE_M 0x3 +#define PORT_MMD_OP_MODE_S 14 +#define PORT_MMD_OP_INDEX 0 +#define PORT_MMD_OP_DATA_NO_INCR 1 +#define PORT_MMD_OP_DATA_INCR_RW 2 +#define PORT_MMD_OP_DATA_INCR_W 3 +#define PORT_MMD_DEVICE_ID_M 0x1F + +#define MMD_SETUP(mode, dev) \ + (((u16)(mode) << PORT_MMD_OP_MODE_S) | (dev)) + +#define REG_PORT_PHY_MMD_INDEX_DATA 0x011C + +#define MMD_DEVICE_ID_DSP 1 + +#define MMD_DSP_SQI_CHAN_A 0xAC +#define MMD_DSP_SQI_CHAN_B 0xAD +#define MMD_DSP_SQI_CHAN_C 0xAE +#define MMD_DSP_SQI_CHAN_D 0xAF + +#define DSP_SQI_ERR_DETECTED BIT(15) +#define DSP_SQI_AVG_ERR 0x7FFF + +#define MMD_DEVICE_ID_COMMON 2 + +#define MMD_DEVICE_ID_EEE_ADV 7 + +#define MMD_EEE_ADV 0x3C +#define EEE_ADV_100MBIT BIT(1) +#define EEE_ADV_1GBIT BIT(2) + +#define MMD_EEE_LP_ADV 0x3D +#define MMD_EEE_MSG_CODE 0x3F + +#define MMD_DEVICE_ID_AFED 0x1C + +#define REG_PORT_PHY_EXTENDED_STATUS 0x011E + +#define PORT_100BTX_FD_ABLE BIT(15) +#define PORT_100BTX_ABLE BIT(14) +#define PORT_10BT_FD_ABLE BIT(13) +#define PORT_10BT_ABLE BIT(12) + +#define REG_PORT_SGMII_ADDR__4 0x0200 +#define PORT_SGMII_AUTO_INCR BIT(23) +#define PORT_SGMII_DEVICE_ID_M 0x1F +#define PORT_SGMII_DEVICE_ID_S 16 +#define PORT_SGMII_ADDR_M (BIT(21) - 1) + +#define REG_PORT_SGMII_DATA__4 0x0204 +#define PORT_SGMII_DATA_M (BIT(16) - 1) + +#define MMD_DEVICE_ID_PMA 0x01 +#define MMD_DEVICE_ID_PCS 0x03 +#define MMD_DEVICE_ID_PHY_XS 0x04 +#define MMD_DEVICE_ID_DTE_XS 0x05 +#define MMD_DEVICE_ID_AN 0x07 +#define MMD_DEVICE_ID_VENDOR_CTRL 0x1E +#define MMD_DEVICE_ID_VENDOR_MII 0x1F + +#define SR_MII MMD_DEVICE_ID_VENDOR_MII + +#define MMD_SR_MII_CTRL 0x0000 + +#define SR_MII_RESET BIT(15) +#define SR_MII_LOOPBACK BIT(14) +#define SR_MII_SPEED_100MBIT BIT(13) +#define SR_MII_AUTO_NEG_ENABLE BIT(12) +#define SR_MII_POWER_DOWN BIT(11) +#define SR_MII_AUTO_NEG_RESTART BIT(9) +#define SR_MII_FULL_DUPLEX BIT(8) +#define SR_MII_SPEED_1000MBIT BIT(6) + +#define MMD_SR_MII_STATUS 0x0001 +#define MMD_SR_MII_ID_1 0x0002 +#define MMD_SR_MII_ID_2 0x0003 +#define MMD_SR_MII_AUTO_NEGOTIATION 0x0004 + +#define SR_MII_AUTO_NEG_NEXT_PAGE BIT(15) +#define SR_MII_AUTO_NEG_REMOTE_FAULT_M 0x3 +#define SR_MII_AUTO_NEG_REMOTE_FAULT_S 12 +#define SR_MII_AUTO_NEG_NO_ERROR 0 +#define SR_MII_AUTO_NEG_OFFLINE 1 +#define SR_MII_AUTO_NEG_LINK_FAILURE 2 +#define SR_MII_AUTO_NEG_ERROR 3 +#define SR_MII_AUTO_NEG_PAUSE_M 0x3 +#define SR_MII_AUTO_NEG_PAUSE_S 7 +#define SR_MII_AUTO_NEG_NO_PAUSE 0 +#define SR_MII_AUTO_NEG_ASYM_PAUSE_TX 1 +#define SR_MII_AUTO_NEG_SYM_PAUSE 2 +#define SR_MII_AUTO_NEG_ASYM_PAUSE_RX 3 +#define SR_MII_AUTO_NEG_HALF_DUPLEX BIT(6) +#define SR_MII_AUTO_NEG_FULL_DUPLEX BIT(5) + +#define MMD_SR_MII_REMOTE_CAPABILITY 0x0005 +#define MMD_SR_MII_AUTO_NEG_EXP 0x0006 +#define MMD_SR_MII_AUTO_NEG_EXT 0x000F + +#define MMD_SR_MII_DIGITAL_CTRL_1 0x8000 + +#define MMD_SR_MII_AUTO_NEG_CTRL 0x8001 + +#define SR_MII_8_BIT BIT(8) +#define SR_MII_SGMII_LINK_UP BIT(4) +#define SR_MII_TX_CFG_PHY_MASTER BIT(3) +#define SR_MII_PCS_MODE_M 0x3 +#define SR_MII_PCS_MODE_S 1 +#define SR_MII_PCS_SGMII 2 +#define SR_MII_AUTO_NEG_COMPLETE_INTR BIT(0) + +#define MMD_SR_MII_AUTO_NEG_STATUS 0x8002 + +#define SR_MII_STAT_LINK_UP BIT(4) +#define SR_MII_STAT_M 0x3 +#define SR_MII_STAT_S 2 +#define SR_MII_STAT_10_MBPS 0 +#define SR_MII_STAT_100_MBPS 1 +#define SR_MII_STAT_1000_MBPS 2 +#define SR_MII_STAT_FULL_DUPLEX BIT(1) + +#define MMD_SR_MII_PHY_CTRL 0x80A0 + +#define SR_MII_PHY_LANE_SEL_M 0xF +#define SR_MII_PHY_LANE_SEL_S 8 +#define SR_MII_PHY_WRITE BIT(1) +#define SR_MII_PHY_START_BUSY BIT(0) + +#define MMD_SR_MII_PHY_ADDR 0x80A1 + +#define SR_MII_PHY_ADDR_M (BIT(16) - 1) + +#define MMD_SR_MII_PHY_DATA 0x80A2 + +#define SR_MII_PHY_DATA_M (BIT(16) - 1) + +#define SR_MII_PHY_JTAG_CHIP_ID_HI 0x000C +#define SR_MII_PHY_JTAG_CHIP_ID_LO 0x000D + +#define REG_PORT_PHY_REMOTE_LB_LED 0x0122 + +#define PORT_REMOTE_LOOPBACK BIT(8) +#define PORT_LED_SELECT (3 << 6) +#define PORT_LED_CTRL (3 << 4) +#define PORT_LED_CTRL_TEST BIT(3) +#define PORT_10BT_PREAMBLE BIT(2) +#define PORT_LINK_MD_10BT_ENABLE BIT(1) +#define PORT_LINK_MD_PASS BIT(0) + +#define REG_PORT_PHY_LINK_MD 0x0124 + +#define PORT_START_CABLE_DIAG BIT(15) +#define PORT_TX_DISABLE BIT(14) +#define PORT_CABLE_DIAG_PAIR_M 0x3 +#define PORT_CABLE_DIAG_PAIR_S 12 +#define PORT_CABLE_DIAG_SELECT_M 0x3 +#define PORT_CABLE_DIAG_SELECT_S 10 +#define PORT_CABLE_DIAG_RESULT_M 0x3 +#define PORT_CABLE_DIAG_RESULT_S 8 +#define PORT_CABLE_STAT_NORMAL 0 +#define PORT_CABLE_STAT_OPEN 1 +#define PORT_CABLE_STAT_SHORT 2 +#define PORT_CABLE_STAT_FAILED 3 +#define PORT_CABLE_FAULT_COUNTER 0x00FF + +#define REG_PORT_PHY_PMA_STATUS 0x0126 + +#define PORT_1000_LINK_GOOD BIT(1) +#define PORT_100_LINK_GOOD BIT(0) + +#define REG_PORT_PHY_DIGITAL_STATUS 0x0128 + +#define PORT_LINK_DETECT BIT(14) +#define PORT_SIGNAL_DETECT BIT(13) +#define PORT_PHY_STAT_MDI BIT(12) +#define PORT_PHY_STAT_MASTER BIT(11) + +#define REG_PORT_PHY_RXER_COUNTER 0x012A + +#define REG_PORT_PHY_INT_ENABLE 0x0136 +#define REG_PORT_PHY_INT_STATUS 0x0137 + +#define JABBER_INT BIT(7) +#define RX_ERR_INT BIT(6) +#define PAGE_RX_INT BIT(5) +#define PARALLEL_DETECT_FAULT_INT BIT(4) +#define LINK_PARTNER_ACK_INT BIT(3) +#define LINK_DOWN_INT BIT(2) +#define REMOTE_FAULT_INT BIT(1) +#define LINK_UP_INT BIT(0) + +#define REG_PORT_PHY_DIGITAL_DEBUG_1 0x0138 + +#define PORT_REG_CLK_SPEED_25_MHZ BIT(14) +#define PORT_PHY_FORCE_MDI BIT(7) +#define PORT_PHY_AUTO_MDIX_DISABLE BIT(6) + +/* Same as PORT_PHY_LOOPBACK */ +#define PORT_PHY_PCS_LOOPBACK BIT(0) + +#define REG_PORT_PHY_DIGITAL_DEBUG_2 0x013A + +#define REG_PORT_PHY_DIGITAL_DEBUG_3 0x013C + +#define PORT_100BT_FIXED_LATENCY BIT(15) + +#define REG_PORT_PHY_PHY_CTRL 0x013E + +#define PORT_INT_PIN_HIGH BIT(14) +#define PORT_ENABLE_JABBER BIT(9) +#define PORT_STAT_SPEED_1000MBIT BIT(6) +#define PORT_STAT_SPEED_100MBIT BIT(5) +#define PORT_STAT_SPEED_10MBIT BIT(4) +#define PORT_STAT_FULL_DUPLEX BIT(3) + +/* Same as PORT_PHY_STAT_MASTER */ +#define PORT_STAT_MASTER BIT(2) +#define PORT_RESET BIT(1) +#define PORT_LINK_STATUS_FAIL BIT(0) + +/* 3 - xMII */ +#define REG_PORT_XMII_CTRL_0 0x0300 + +#define PORT_SGMII_SEL BIT(7) +#define PORT_MII_FULL_DUPLEX BIT(6) +#define PORT_MII_100MBIT BIT(4) +#define PORT_GRXC_ENABLE BIT(0) + +#define REG_PORT_XMII_CTRL_1 0x0301 + +#define PORT_RMII_CLK_SEL BIT(7) +/* S1 */ +#define PORT_MII_1000MBIT_S1 BIT(6) +/* S2 */ +#define PORT_MII_NOT_1GBIT BIT(6) +#define PORT_MII_SEL_EDGE BIT(5) +#define PORT_RGMII_ID_IG_ENABLE BIT(4) +#define PORT_RGMII_ID_EG_ENABLE BIT(3) +#define PORT_MII_MAC_MODE BIT(2) +#define PORT_MII_SEL_M 0x3 +/* S1 */ +#define PORT_MII_SEL_S1 0x0 +#define PORT_RMII_SEL_S1 0x1 +#define PORT_GMII_SEL_S1 0x2 +#define PORT_RGMII_SEL_S1 0x3 +/* S2 */ +#define PORT_RGMII_SEL 0x0 +#define PORT_RMII_SEL 0x1 +#define PORT_GMII_SEL 0x2 +#define PORT_MII_SEL 0x3 + +/* 4 - MAC */ +#define REG_PORT_MAC_CTRL_0 0x0400 + +#define PORT_BROADCAST_STORM BIT(1) +#define PORT_JUMBO_FRAME BIT(0) + +#define REG_PORT_MAC_CTRL_1 0x0401 + +#define PORT_BACK_PRESSURE BIT(3) +#define PORT_PASS_ALL BIT(0) + +#define REG_PORT_MAC_CTRL_2 0x0402 + +#define PORT_100BT_EEE_DISABLE BIT(7) +#define PORT_1000BT_EEE_DISABLE BIT(6) + +#define REG_PORT_MAC_IN_RATE_LIMIT 0x0403 + +#define PORT_IN_PORT_BASED_S 6 +#define PORT_RATE_PACKET_BASED_S 5 +#define PORT_IN_FLOW_CTRL_S 4 +#define PORT_COUNT_IFG_S 1 +#define PORT_COUNT_PREAMBLE_S 0 +#define PORT_IN_PORT_BASED BIT(6) +#define PORT_IN_PACKET_BASED BIT(5) +#define PORT_IN_FLOW_CTRL BIT(4) +#define PORT_IN_LIMIT_MODE_M 0x3 +#define PORT_IN_LIMIT_MODE_S 2 +#define PORT_IN_ALL 0 +#define PORT_IN_UNICAST 1 +#define PORT_IN_MULTICAST 2 +#define PORT_IN_BROADCAST 3 +#define PORT_COUNT_IFG BIT(1) +#define PORT_COUNT_PREAMBLE BIT(0) + +#define REG_PORT_IN_RATE_0 0x0410 +#define REG_PORT_IN_RATE_1 0x0411 +#define REG_PORT_IN_RATE_2 0x0412 +#define REG_PORT_IN_RATE_3 0x0413 +#define REG_PORT_IN_RATE_4 0x0414 +#define REG_PORT_IN_RATE_5 0x0415 +#define REG_PORT_IN_RATE_6 0x0416 +#define REG_PORT_IN_RATE_7 0x0417 + +#define REG_PORT_OUT_RATE_0 0x0420 +#define REG_PORT_OUT_RATE_1 0x0421 +#define REG_PORT_OUT_RATE_2 0x0422 +#define REG_PORT_OUT_RATE_3 0x0423 + +#define PORT_RATE_LIMIT_M (BIT(7) - 1) + +/* 5 - MIB Counters */ +#define REG_PORT_MIB_CTRL_STAT__4 0x0500 + +#define MIB_COUNTER_OVERFLOW BIT(31) +#define MIB_COUNTER_VALID BIT(30) +#define MIB_COUNTER_READ BIT(25) +#define MIB_COUNTER_FLUSH_FREEZE BIT(24) +#define MIB_COUNTER_INDEX_M (BIT(8) - 1) +#define MIB_COUNTER_INDEX_S 16 +#define MIB_COUNTER_DATA_HI_M 0xF + +#define REG_PORT_MIB_DATA 0x0504 + +/* 6 - ACL */ +#define REG_PORT_ACL_0 0x0600 + +#define ACL_FIRST_RULE_M 0xF + +#define REG_PORT_ACL_1 0x0601 + +#define ACL_MODE_M 0x3 +#define ACL_MODE_S 4 +#define ACL_MODE_DISABLE 0 +#define ACL_MODE_LAYER_2 1 +#define ACL_MODE_LAYER_3 2 +#define ACL_MODE_LAYER_4 3 +#define ACL_ENABLE_M 0x3 +#define ACL_ENABLE_S 2 +#define ACL_ENABLE_2_COUNT 0 +#define ACL_ENABLE_2_TYPE 1 +#define ACL_ENABLE_2_MAC 2 +#define ACL_ENABLE_2_BOTH 3 +#define ACL_ENABLE_3_IP 1 +#define ACL_ENABLE_3_SRC_DST_COMP 2 +#define ACL_ENABLE_4_PROTOCOL 0 +#define ACL_ENABLE_4_TCP_PORT_COMP 1 +#define ACL_ENABLE_4_UDP_PORT_COMP 2 +#define ACL_ENABLE_4_TCP_SEQN_COMP 3 +#define ACL_SRC BIT(1) +#define ACL_EQUAL BIT(0) + +#define REG_PORT_ACL_2 0x0602 +#define REG_PORT_ACL_3 0x0603 + +#define ACL_MAX_PORT 0xFFFF + +#define REG_PORT_ACL_4 0x0604 +#define REG_PORT_ACL_5 0x0605 + +#define ACL_MIN_PORT 0xFFFF +#define ACL_IP_ADDR 0xFFFFFFFF +#define ACL_TCP_SEQNUM 0xFFFFFFFF + +#define REG_PORT_ACL_6 0x0606 + +#define ACL_RESERVED 0xF8 +#define ACL_PORT_MODE_M 0x3 +#define ACL_PORT_MODE_S 1 +#define ACL_PORT_MODE_DISABLE 0 +#define ACL_PORT_MODE_EITHER 1 +#define ACL_PORT_MODE_IN_RANGE 2 +#define ACL_PORT_MODE_OUT_OF_RANGE 3 + +#define REG_PORT_ACL_7 0x0607 + +#define ACL_TCP_FLAG_ENABLE BIT(0) + +#define REG_PORT_ACL_8 0x0608 + +#define ACL_TCP_FLAG_M 0xFF + +#define REG_PORT_ACL_9 0x0609 + +#define ACL_TCP_FLAG 0xFF +#define ACL_ETH_TYPE 0xFFFF +#define ACL_IP_M 0xFFFFFFFF + +#define REG_PORT_ACL_A 0x060A + +#define ACL_PRIO_MODE_M 0x3 +#define ACL_PRIO_MODE_S 6 +#define ACL_PRIO_MODE_DISABLE 0 +#define ACL_PRIO_MODE_HIGHER 1 +#define ACL_PRIO_MODE_LOWER 2 +#define ACL_PRIO_MODE_REPLACE 3 +#define ACL_PRIO_M KS_PRIO_M +#define ACL_PRIO_S 3 +#define ACL_VLAN_PRIO_REPLACE BIT(2) +#define ACL_VLAN_PRIO_M KS_PRIO_M +#define ACL_VLAN_PRIO_HI_M 0x3 + +#define REG_PORT_ACL_B 0x060B + +#define ACL_VLAN_PRIO_LO_M 0x8 +#define ACL_VLAN_PRIO_S 7 +#define ACL_MAP_MODE_M 0x3 +#define ACL_MAP_MODE_S 5 +#define ACL_MAP_MODE_DISABLE 0 +#define ACL_MAP_MODE_OR 1 +#define ACL_MAP_MODE_AND 2 +#define ACL_MAP_MODE_REPLACE 3 + +#define ACL_CNT_M (BIT(11) - 1) +#define ACL_CNT_S 5 + +#define REG_PORT_ACL_C 0x060C + +#define REG_PORT_ACL_D 0x060D +#define ACL_MSEC_UNIT BIT(6) +#define ACL_INTR_MODE BIT(5) +#define ACL_PORT_MAP 0x7F + +#define REG_PORT_ACL_E 0x060E +#define REG_PORT_ACL_F 0x060F + +#define REG_PORT_ACL_BYTE_EN_MSB 0x0610 +#define REG_PORT_ACL_BYTE_EN_LSB 0x0611 + +#define ACL_ACTION_START 0xA +#define ACL_ACTION_LEN 4 +#define ACL_INTR_CNT_START 0xD +#define ACL_RULESET_START 0xE +#define ACL_RULESET_LEN 2 +#define ACL_TABLE_LEN 16 + +#define ACL_ACTION_ENABLE 0x003C +#define ACL_MATCH_ENABLE 0x7FC3 +#define ACL_RULESET_ENABLE 0x8003 +#define ACL_BYTE_ENABLE 0xFFFF + +#define REG_PORT_ACL_CTRL_0 0x0612 + +#define PORT_ACL_WRITE_DONE BIT(6) +#define PORT_ACL_READ_DONE BIT(5) +#define PORT_ACL_WRITE BIT(4) +#define PORT_ACL_INDEX_M 0xF + +#define REG_PORT_ACL_CTRL_1 0x0613 + +/* 8 - Classification and Policing */ +#define REG_PORT_MRI_MIRROR_CTRL 0x0800 + +#define PORT_MIRROR_RX BIT(6) +#define PORT_MIRROR_TX BIT(5) +#define PORT_MIRROR_SNIFFER BIT(1) + +#define REG_PORT_MRI_PRIO_CTRL 0x0801 + +#define PORT_HIGHEST_PRIO BIT(7) +#define PORT_OR_PRIO BIT(6) +#define PORT_MAC_PRIO_ENABLE BIT(4) +#define PORT_VLAN_PRIO_ENABLE BIT(3) +#define PORT_802_1P_PRIO_ENABLE BIT(2) +#define PORT_DIFFSERV_PRIO_ENABLE BIT(1) +#define PORT_ACL_PRIO_ENABLE BIT(0) + +#define REG_PORT_MRI_MAC_CTRL 0x0802 + +#define PORT_USER_PRIO_CEILING BIT(7) +#define PORT_DROP_NON_VLAN BIT(4) +#define PORT_DROP_TAG BIT(3) +#define PORT_BASED_PRIO_M KS_PRIO_M +#define PORT_BASED_PRIO_S 0 + +#define REG_PORT_MRI_AUTHEN_CTRL 0x0803 + +#define PORT_ACL_ENABLE BIT(2) +#define PORT_AUTHEN_MODE 0x3 +#define PORT_AUTHEN_PASS 0 +#define PORT_AUTHEN_BLOCK 1 +#define PORT_AUTHEN_TRAP 2 + +#define REG_PORT_MRI_INDEX__4 0x0804 + +#define MRI_INDEX_P_M 0x7 +#define MRI_INDEX_P_S 16 +#define MRI_INDEX_Q_M 0x3 +#define MRI_INDEX_Q_S 0 + +#define REG_PORT_MRI_TC_MAP__4 0x0808 + +#define PORT_TC_MAP_M 0xf +#define PORT_TC_MAP_S 4 + +#define REG_PORT_MRI_POLICE_CTRL__4 0x080C + +#define POLICE_DROP_ALL BIT(10) +#define POLICE_PACKET_TYPE_M 0x3 +#define POLICE_PACKET_TYPE_S 8 +#define POLICE_PACKET_DROPPED 0 +#define POLICE_PACKET_GREEN 1 +#define POLICE_PACKET_YELLOW 2 +#define POLICE_PACKET_RED 3 +#define PORT_BASED_POLICING BIT(7) +#define NON_DSCP_COLOR_M 0x3 +#define NON_DSCP_COLOR_S 5 +#define COLOR_MARK_ENABLE BIT(4) +#define COLOR_REMAP_ENABLE BIT(3) +#define POLICE_DROP_SRP BIT(2) +#define POLICE_COLOR_NOT_AWARE BIT(1) +#define POLICE_ENABLE BIT(0) + +#define REG_PORT_POLICE_COLOR_0__4 0x0810 +#define REG_PORT_POLICE_COLOR_1__4 0x0814 +#define REG_PORT_POLICE_COLOR_2__4 0x0818 +#define REG_PORT_POLICE_COLOR_3__4 0x081C + +#define POLICE_COLOR_MAP_S 2 +#define POLICE_COLOR_MAP_M (BIT(POLICE_COLOR_MAP_S) - 1) + +#define REG_PORT_POLICE_RATE__4 0x0820 + +#define POLICE_CIR_S 16 +#define POLICE_PIR_S 0 + +#define REG_PORT_POLICE_BURST_SIZE__4 0x0824 + +#define POLICE_BURST_SIZE_M 0x3FFF +#define POLICE_CBS_S 16 +#define POLICE_PBS_S 0 + +#define REG_PORT_WRED_PM_CTRL_0__4 0x0830 + +#define WRED_PM_CTRL_M (BIT(11) - 1) + +#define WRED_PM_MAX_THRESHOLD_S 16 +#define WRED_PM_MIN_THRESHOLD_S 0 + +#define REG_PORT_WRED_PM_CTRL_1__4 0x0834 + +#define WRED_PM_MULTIPLIER_S 16 +#define WRED_PM_AVG_QUEUE_SIZE_S 0 + +#define REG_PORT_WRED_QUEUE_CTRL_0__4 0x0840 +#define REG_PORT_WRED_QUEUE_CTRL_1__4 0x0844 + +#define REG_PORT_WRED_QUEUE_PMON__4 0x0848 + +#define WRED_RANDOM_DROP_ENABLE BIT(31) +#define WRED_PMON_FLUSH BIT(30) +#define WRED_DROP_GYR_DISABLE BIT(29) +#define WRED_DROP_YR_DISABLE BIT(28) +#define WRED_DROP_R_DISABLE BIT(27) +#define WRED_DROP_ALL BIT(26) +#define WRED_PMON_M (BIT(24) - 1) + +/* 9 - Shaping */ + +#define REG_PORT_MTI_QUEUE_INDEX__4 0x0900 + +#define REG_PORT_MTI_QUEUE_CTRL_0__4 0x0904 + +#define MTI_PVID_REPLACE BIT(0) + +#define REG_PORT_MTI_QUEUE_CTRL_0 0x0914 + +#define MTI_SCHEDULE_MODE_M 0x3 +#define MTI_SCHEDULE_MODE_S 6 +#define MTI_SCHEDULE_STRICT_PRIO 0 +#define MTI_SCHEDULE_WRR 2 +#define MTI_SHAPING_M 0x3 +#define MTI_SHAPING_S 4 +#define MTI_SHAPING_OFF 0 +#define MTI_SHAPING_SRP 1 +#define MTI_SHAPING_TIME_AWARE 2 + +#define REG_PORT_MTI_QUEUE_CTRL_1 0x0915 + +#define MTI_TX_RATIO_M (BIT(7) - 1) + +#define REG_PORT_MTI_QUEUE_CTRL_2__2 0x0916 +#define REG_PORT_MTI_HI_WATER_MARK 0x0916 +#define REG_PORT_MTI_QUEUE_CTRL_3__2 0x0918 +#define REG_PORT_MTI_LO_WATER_MARK 0x0918 +#define REG_PORT_MTI_QUEUE_CTRL_4__2 0x091A +#define REG_PORT_MTI_CREDIT_INCREMENT 0x091A + +/* A - QM */ + +#define REG_PORT_QM_CTRL__4 0x0A00 + +#define PORT_QM_DROP_PRIO_M 0x3 + +#define REG_PORT_VLAN_MEMBERSHIP__4 0x0A04 + +#define REG_PORT_QM_QUEUE_INDEX__4 0x0A08 + +#define PORT_QM_QUEUE_INDEX_S 24 +#define PORT_QM_BURST_SIZE_S 16 +#define PORT_QM_MIN_RESV_SPACE_M (BIT(11) - 1) + +#define REG_PORT_QM_WATER_MARK__4 0x0A0C + +#define PORT_QM_HI_WATER_MARK_S 16 +#define PORT_QM_LO_WATER_MARK_S 0 +#define PORT_QM_WATER_MARK_M (BIT(11) - 1) + +#define REG_PORT_QM_TX_CNT_0__4 0x0A10 + +#define PORT_QM_TX_CNT_USED_S 0 +#define PORT_QM_TX_CNT_M (BIT(11) - 1) + +#define REG_PORT_QM_TX_CNT_1__4 0x0A14 + +#define PORT_QM_TX_CNT_CALCULATED_S 16 +#define PORT_QM_TX_CNT_AVAIL_S 0 + +/* B - LUE */ +#define REG_PORT_LUE_CTRL 0x0B00 + +#define PORT_VLAN_LOOKUP_VID_0 BIT(7) +#define PORT_INGRESS_FILTER BIT(6) +#define PORT_DISCARD_NON_VID BIT(5) +#define PORT_MAC_BASED_802_1X BIT(4) +#define PORT_SRC_ADDR_FILTER BIT(3) + +#define REG_PORT_LUE_MSTP_INDEX 0x0B01 + +#define REG_PORT_LUE_MSTP_STATE 0x0B04 + +#define PORT_TX_ENABLE BIT(2) +#define PORT_RX_ENABLE BIT(1) +#define PORT_LEARN_DISABLE BIT(0) + +/* C - PTP */ + +#define REG_PTP_PORT_RX_DELAY__2 0x0C00 +#define REG_PTP_PORT_TX_DELAY__2 0x0C02 +#define REG_PTP_PORT_ASYM_DELAY__2 0x0C04 + +#define REG_PTP_PORT_XDELAY_TS 0x0C08 +#define REG_PTP_PORT_XDELAY_TS_H 0x0C08 +#define REG_PTP_PORT_XDELAY_TS_L 0x0C0A + +#define REG_PTP_PORT_SYNC_TS 0x0C0C +#define REG_PTP_PORT_SYNC_TS_H 0x0C0C +#define REG_PTP_PORT_SYNC_TS_L 0x0C0E + +#define REG_PTP_PORT_PDRESP_TS 0x0C10 +#define REG_PTP_PORT_PDRESP_TS_H 0x0C10 +#define REG_PTP_PORT_PDRESP_TS_L 0x0C12 + +#define REG_PTP_PORT_TX_INT_STATUS__2 0x0C14 +#define REG_PTP_PORT_TX_INT_ENABLE__2 0x0C16 + +#define PTP_PORT_SYNC_INT BIT(15) +#define PTP_PORT_XDELAY_REQ_INT BIT(14) +#define PTP_PORT_PDELAY_RESP_INT BIT(13) + +#define REG_PTP_PORT_LINK_DELAY__4 0x0C18 + +#define PRIO_QUEUES 4 +#define RX_PRIO_QUEUES 8 + +#define KS_PRIO_IN_REG 2 + +#define TOTAL_PORT_NUM 7 + +#define KSZ9477_COUNTER_NUM 0x20 +#define TOTAL_KSZ9477_COUNTER_NUM (KSZ9477_COUNTER_NUM + 2 + 2) + +#define SWITCH_COUNTER_NUM KSZ9477_COUNTER_NUM +#define TOTAL_SWITCH_COUNTER_NUM TOTAL_KSZ9477_COUNTER_NUM + +#define P_BCAST_STORM_CTRL REG_PORT_MAC_CTRL_0 +#define P_PRIO_CTRL REG_PORT_MRI_PRIO_CTRL +#define P_MIRROR_CTRL REG_PORT_MRI_MIRROR_CTRL +#define P_STP_CTRL REG_PORT_LUE_MSTP_STATE +#define P_PHY_CTRL REG_PORT_PHY_CTRL +#define P_NEG_RESTART_CTRL REG_PORT_PHY_CTRL +#define P_LINK_STATUS REG_PORT_PHY_STATUS +#define P_SPEED_STATUS REG_PORT_PHY_PHY_CTRL +#define P_RATE_LIMIT_CTRL REG_PORT_MAC_IN_RATE_LIMIT + +#define S_LINK_AGING_CTRL REG_SW_LUE_CTRL_1 +#define S_MIRROR_CTRL REG_SW_MRI_CTRL_0 +#define S_REPLACE_VID_CTRL REG_SW_MAC_CTRL_2 +#define S_802_1P_PRIO_CTRL REG_SW_MAC_802_1P_MAP_0 +#define S_TOS_PRIO_CTRL REG_SW_MAC_TOS_PRIO_0 +#define S_FLUSH_TABLE_CTRL REG_SW_LUE_CTRL_1 + +#define SW_FLUSH_DYN_MAC_TABLE SW_FLUSH_MSTP_TABLE + +#define MAX_TIMESTAMP_UNIT 2 +#define MAX_TRIG_UNIT 3 +#define MAX_TIMESTAMP_EVENT_UNIT 8 +#define MAX_GPIO 4 + +#define PTP_TRIG_UNIT_M (BIT(MAX_TRIG_UNIT) - 1) +#define PTP_TS_UNIT_M (BIT(MAX_TIMESTAMP_UNIT) - 1) + +/* Driver set switch broadcast storm protection at 10% rate. */ +#define BROADCAST_STORM_PROT_RATE 10 + +/* 148,800 frames * 67 ms / 100 */ +#define BROADCAST_STORM_VALUE 9969 + +#endif /* KSZ9477_REGS_H */ diff --git a/drivers/net/dsa/microchip/ksz_common.c b/drivers/net/dsa/microchip/ksz_common.c new file mode 100644 index 000000000000..b313ecdf2919 --- /dev/null +++ b/drivers/net/dsa/microchip/ksz_common.c @@ -0,0 +1,1279 @@ +/* + * Microchip switch driver main logic + * + * Copyright (C) 2017 + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include "ksz_priv.h" + +static const struct { + int index; + char string[ETH_GSTRING_LEN]; +} mib_names[TOTAL_SWITCH_COUNTER_NUM] = { + { 0x00, "rx_hi" }, + { 0x01, "rx_undersize" }, + { 0x02, "rx_fragments" }, + { 0x03, "rx_oversize" }, + { 0x04, "rx_jabbers" }, + { 0x05, "rx_symbol_err" }, + { 0x06, "rx_crc_err" }, + { 0x07, "rx_align_err" }, + { 0x08, "rx_mac_ctrl" }, + { 0x09, "rx_pause" }, + { 0x0A, "rx_bcast" }, + { 0x0B, "rx_mcast" }, + { 0x0C, "rx_ucast" }, + { 0x0D, "rx_64_or_less" }, + { 0x0E, "rx_65_127" }, + { 0x0F, "rx_128_255" }, + { 0x10, "rx_256_511" }, + { 0x11, "rx_512_1023" }, + { 0x12, "rx_1024_1522" }, + { 0x13, "rx_1523_2000" }, + { 0x14, "rx_2001" }, + { 0x15, "tx_hi" }, + { 0x16, "tx_late_col" }, + { 0x17, "tx_pause" }, + { 0x18, "tx_bcast" }, + { 0x19, "tx_mcast" }, + { 0x1A, "tx_ucast" }, + { 0x1B, "tx_deferred" }, + { 0x1C, "tx_total_col" }, + { 0x1D, "tx_exc_col" }, + { 0x1E, "tx_single_col" }, + { 0x1F, "tx_mult_col" }, + { 0x80, "rx_total" }, + { 0x81, "tx_total" }, + { 0x82, "rx_discards" }, + { 0x83, "tx_discards" }, +}; + +static void ksz_cfg(struct ksz_device *dev, u32 addr, u8 bits, bool set) +{ + u8 data; + + ksz_read8(dev, addr, &data); + if (set) + data |= bits; + else + data &= ~bits; + ksz_write8(dev, addr, data); +} + +static void ksz_cfg32(struct ksz_device *dev, u32 addr, u32 bits, bool set) +{ + u32 data; + + ksz_read32(dev, addr, &data); + if (set) + data |= bits; + else + data &= ~bits; + ksz_write32(dev, addr, data); +} + +static void ksz_port_cfg(struct ksz_device *dev, int port, int offset, u8 bits, + bool set) +{ + u32 addr; + u8 data; + + addr = PORT_CTRL_ADDR(port, offset); + ksz_read8(dev, addr, &data); + + if (set) + data |= bits; + else + data &= ~bits; + + ksz_write8(dev, addr, data); +} + +static void ksz_port_cfg32(struct ksz_device *dev, int port, int offset, + u32 bits, bool set) +{ + u32 addr; + u32 data; + + addr = PORT_CTRL_ADDR(port, offset); + ksz_read32(dev, addr, &data); + + if (set) + data |= bits; + else + data &= ~bits; + + ksz_write32(dev, addr, data); +} + +static int wait_vlan_ctrl_ready(struct ksz_device *dev, u32 waiton, int timeout) +{ + u8 data; + + do { + ksz_read8(dev, REG_SW_VLAN_CTRL, &data); + if (!(data & waiton)) + break; + usleep_range(1, 10); + } while (timeout-- > 0); + + if (timeout <= 0) + return -ETIMEDOUT; + + return 0; +} + +static int get_vlan_table(struct dsa_switch *ds, u16 vid, u32 *vlan_table) +{ + struct ksz_device *dev = ds->priv; + int ret; + + mutex_lock(&dev->vlan_mutex); + + ksz_write16(dev, REG_SW_VLAN_ENTRY_INDEX__2, vid & VLAN_INDEX_M); + ksz_write8(dev, REG_SW_VLAN_CTRL, VLAN_READ | VLAN_START); + + /* wait to be cleared */ + ret = wait_vlan_ctrl_ready(dev, VLAN_START, 1000); + if (ret < 0) { + dev_dbg(dev->dev, "Failed to read vlan table\n"); + goto exit; + } + + ksz_read32(dev, REG_SW_VLAN_ENTRY__4, &vlan_table[0]); + ksz_read32(dev, REG_SW_VLAN_ENTRY_UNTAG__4, &vlan_table[1]); + ksz_read32(dev, REG_SW_VLAN_ENTRY_PORTS__4, &vlan_table[2]); + + ksz_write8(dev, REG_SW_VLAN_CTRL, 0); + +exit: + mutex_unlock(&dev->vlan_mutex); + + return ret; +} + +static int set_vlan_table(struct dsa_switch *ds, u16 vid, u32 *vlan_table) +{ + struct ksz_device *dev = ds->priv; + int ret; + + mutex_lock(&dev->vlan_mutex); + + ksz_write32(dev, REG_SW_VLAN_ENTRY__4, vlan_table[0]); + ksz_write32(dev, REG_SW_VLAN_ENTRY_UNTAG__4, vlan_table[1]); + ksz_write32(dev, REG_SW_VLAN_ENTRY_PORTS__4, vlan_table[2]); + + ksz_write16(dev, REG_SW_VLAN_ENTRY_INDEX__2, vid & VLAN_INDEX_M); + ksz_write8(dev, REG_SW_VLAN_CTRL, VLAN_START | VLAN_WRITE); + + /* wait to be cleared */ + ret = wait_vlan_ctrl_ready(dev, VLAN_START, 1000); + if (ret < 0) { + dev_dbg(dev->dev, "Failed to write vlan table\n"); + goto exit; + } + + ksz_write8(dev, REG_SW_VLAN_CTRL, 0); + + /* update vlan cache table */ + dev->vlan_cache[vid].table[0] = vlan_table[0]; + dev->vlan_cache[vid].table[1] = vlan_table[1]; + dev->vlan_cache[vid].table[2] = vlan_table[2]; + +exit: + mutex_unlock(&dev->vlan_mutex); + + return ret; +} + +static void read_table(struct dsa_switch *ds, u32 *table) +{ + struct ksz_device *dev = ds->priv; + + ksz_read32(dev, REG_SW_ALU_VAL_A, &table[0]); + ksz_read32(dev, REG_SW_ALU_VAL_B, &table[1]); + ksz_read32(dev, REG_SW_ALU_VAL_C, &table[2]); + ksz_read32(dev, REG_SW_ALU_VAL_D, &table[3]); +} + +static void write_table(struct dsa_switch *ds, u32 *table) +{ + struct ksz_device *dev = ds->priv; + + ksz_write32(dev, REG_SW_ALU_VAL_A, table[0]); + ksz_write32(dev, REG_SW_ALU_VAL_B, table[1]); + ksz_write32(dev, REG_SW_ALU_VAL_C, table[2]); + ksz_write32(dev, REG_SW_ALU_VAL_D, table[3]); +} + +static int wait_alu_ready(struct ksz_device *dev, u32 waiton, int timeout) +{ + u32 data; + + do { + ksz_read32(dev, REG_SW_ALU_CTRL__4, &data); + if (!(data & waiton)) + break; + usleep_range(1, 10); + } while (timeout-- > 0); + + if (timeout <= 0) + return -ETIMEDOUT; + + return 0; +} + +static int wait_alu_sta_ready(struct ksz_device *dev, u32 waiton, int timeout) +{ + u32 data; + + do { + ksz_read32(dev, REG_SW_ALU_STAT_CTRL__4, &data); + if (!(data & waiton)) + break; + usleep_range(1, 10); + } while (timeout-- > 0); + + if (timeout <= 0) + return -ETIMEDOUT; + + return 0; +} + +static int ksz_reset_switch(struct dsa_switch *ds) +{ + struct ksz_device *dev = ds->priv; + u8 data8; + u16 data16; + u32 data32; + + /* reset switch */ + ksz_cfg(dev, REG_SW_OPERATION, SW_RESET, true); + + /* turn off SPI DO Edge select */ + ksz_read8(dev, REG_SW_GLOBAL_SERIAL_CTRL_0, &data8); + data8 &= ~SPI_AUTO_EDGE_DETECTION; + ksz_write8(dev, REG_SW_GLOBAL_SERIAL_CTRL_0, data8); + + /* default configuration */ + ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8); + data8 = SW_AGING_ENABLE | SW_LINK_AUTO_AGING | + SW_SRC_ADDR_FILTER | SW_FLUSH_STP_TABLE | SW_FLUSH_MSTP_TABLE; + ksz_write8(dev, REG_SW_LUE_CTRL_1, data8); + + /* disable interrupts */ + ksz_write32(dev, REG_SW_INT_MASK__4, SWITCH_INT_MASK); + ksz_write32(dev, REG_SW_PORT_INT_MASK__4, 0x7F); + ksz_read32(dev, REG_SW_PORT_INT_STATUS__4, &data32); + + /* set broadcast storm protection 10% rate */ + ksz_read16(dev, REG_SW_MAC_CTRL_2, &data16); + data16 &= ~BROADCAST_STORM_RATE; + data16 |= (BROADCAST_STORM_VALUE * BROADCAST_STORM_PROT_RATE) / 100; + ksz_write16(dev, REG_SW_MAC_CTRL_2, data16); + + return 0; +} + +static void port_setup(struct ksz_device *dev, int port, bool cpu_port) +{ + u8 data8; + u16 data16; + + /* enable tag tail for host port */ + if (cpu_port) + ksz_port_cfg(dev, port, REG_PORT_CTRL_0, PORT_TAIL_TAG_ENABLE, + true); + + ksz_port_cfg(dev, port, REG_PORT_CTRL_0, PORT_MAC_LOOPBACK, false); + + /* set back pressure */ + ksz_port_cfg(dev, port, REG_PORT_MAC_CTRL_1, PORT_BACK_PRESSURE, true); + + /* set flow control */ + ksz_port_cfg(dev, port, REG_PORT_CTRL_0, + PORT_FORCE_TX_FLOW_CTRL | PORT_FORCE_RX_FLOW_CTRL, true); + + /* enable broadcast storm limit */ + ksz_port_cfg(dev, port, P_BCAST_STORM_CTRL, PORT_BROADCAST_STORM, true); + + /* disable DiffServ priority */ + ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_DIFFSERV_PRIO_ENABLE, false); + + /* replace priority */ + ksz_port_cfg(dev, port, REG_PORT_MRI_MAC_CTRL, PORT_USER_PRIO_CEILING, + false); + ksz_port_cfg32(dev, port, REG_PORT_MTI_QUEUE_CTRL_0__4, + MTI_PVID_REPLACE, false); + + /* enable 802.1p priority */ + ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_PRIO_ENABLE, true); + + /* configure MAC to 1G & RGMII mode */ + ksz_pread8(dev, port, REG_PORT_XMII_CTRL_1, &data8); + data8 |= PORT_RGMII_ID_EG_ENABLE; + data8 &= ~PORT_MII_NOT_1GBIT; + data8 &= ~PORT_MII_SEL_M; + data8 |= PORT_RGMII_SEL; + ksz_pwrite8(dev, port, REG_PORT_XMII_CTRL_1, data8); + + /* clear pending interrupts */ + ksz_pread16(dev, port, REG_PORT_PHY_INT_ENABLE, &data16); +} + +static void ksz_config_cpu_port(struct dsa_switch *ds) +{ + struct ksz_device *dev = ds->priv; + int i; + + ds->num_ports = dev->port_cnt; + + for (i = 0; i < ds->num_ports; i++) { + if (dsa_is_cpu_port(ds, i) && (dev->cpu_ports & (1 << i))) { + dev->cpu_port = i; + + /* enable cpu port */ + port_setup(dev, i, true); + } + } +} + +static int ksz_setup(struct dsa_switch *ds) +{ + struct ksz_device *dev = ds->priv; + int ret = 0; + + dev->vlan_cache = devm_kcalloc(dev->dev, sizeof(struct vlan_table), + dev->num_vlans, GFP_KERNEL); + if (!dev->vlan_cache) + return -ENOMEM; + + ret = ksz_reset_switch(ds); + if (ret) { + dev_err(ds->dev, "failed to reset switch\n"); + return ret; + } + + /* accept packet up to 2000bytes */ + ksz_cfg(dev, REG_SW_MAC_CTRL_1, SW_LEGAL_PACKET_DISABLE, true); + + ksz_config_cpu_port(ds); + + ksz_cfg(dev, REG_SW_MAC_CTRL_1, MULTICAST_STORM_DISABLE, true); + + /* queue based egress rate limit */ + ksz_cfg(dev, REG_SW_MAC_CTRL_5, SW_OUT_RATE_LIMIT_QUEUE_BASED, true); + + /* start switch */ + ksz_cfg(dev, REG_SW_OPERATION, SW_START, true); + + return 0; +} + +static enum dsa_tag_protocol ksz_get_tag_protocol(struct dsa_switch *ds) +{ + return DSA_TAG_PROTO_KSZ; +} + +static int ksz_phy_read16(struct dsa_switch *ds, int addr, int reg) +{ + struct ksz_device *dev = ds->priv; + u16 val = 0; + + ksz_pread16(dev, addr, 0x100 + (reg << 1), &val); + + return val; +} + +static int ksz_phy_write16(struct dsa_switch *ds, int addr, int reg, u16 val) +{ + struct ksz_device *dev = ds->priv; + + ksz_pwrite16(dev, addr, 0x100 + (reg << 1), val); + + return 0; +} + +static int ksz_enable_port(struct dsa_switch *ds, int port, + struct phy_device *phy) +{ + struct ksz_device *dev = ds->priv; + + /* setup slave port */ + port_setup(dev, port, false); + + return 0; +} + +static void ksz_disable_port(struct dsa_switch *ds, int port, + struct phy_device *phy) +{ + struct ksz_device *dev = ds->priv; + + /* there is no port disable */ + ksz_port_cfg(dev, port, REG_PORT_CTRL_0, PORT_MAC_LOOPBACK, true); +} + +static int ksz_sset_count(struct dsa_switch *ds) +{ + return TOTAL_SWITCH_COUNTER_NUM; +} + +static void ksz_get_strings(struct dsa_switch *ds, int port, uint8_t *buf) +{ + int i; + + for (i = 0; i < TOTAL_SWITCH_COUNTER_NUM; i++) { + memcpy(buf + i * ETH_GSTRING_LEN, mib_names[i].string, + ETH_GSTRING_LEN); + } +} + +static void ksz_get_ethtool_stats(struct dsa_switch *ds, int port, + uint64_t *buf) +{ + struct ksz_device *dev = ds->priv; + int i; + u32 data; + int timeout; + + mutex_lock(&dev->stats_mutex); + + for (i = 0; i < TOTAL_SWITCH_COUNTER_NUM; i++) { + data = MIB_COUNTER_READ; + data |= ((mib_names[i].index & 0xFF) << MIB_COUNTER_INDEX_S); + ksz_pwrite32(dev, port, REG_PORT_MIB_CTRL_STAT__4, data); + + timeout = 1000; + do { + ksz_pread32(dev, port, REG_PORT_MIB_CTRL_STAT__4, + &data); + usleep_range(1, 10); + if (!(data & MIB_COUNTER_READ)) + break; + } while (timeout-- > 0); + + /* failed to read MIB. get out of loop */ + if (!timeout) { + dev_dbg(dev->dev, "Failed to get MIB\n"); + break; + } + + /* count resets upon read */ + ksz_pread32(dev, port, REG_PORT_MIB_DATA, &data); + + dev->mib_value[i] += (uint64_t)data; + buf[i] = dev->mib_value[i]; + } + + mutex_unlock(&dev->stats_mutex); +} + +static void ksz_port_stp_state_set(struct dsa_switch *ds, int port, u8 state) +{ + struct ksz_device *dev = ds->priv; + u8 data; + + ksz_pread8(dev, port, P_STP_CTRL, &data); + data &= ~(PORT_TX_ENABLE | PORT_RX_ENABLE | PORT_LEARN_DISABLE); + + switch (state) { + case BR_STATE_DISABLED: + data |= PORT_LEARN_DISABLE; + break; + case BR_STATE_LISTENING: + data |= (PORT_RX_ENABLE | PORT_LEARN_DISABLE); + break; + case BR_STATE_LEARNING: + data |= PORT_RX_ENABLE; + break; + case BR_STATE_FORWARDING: + data |= (PORT_TX_ENABLE | PORT_RX_ENABLE); + break; + case BR_STATE_BLOCKING: + data |= PORT_LEARN_DISABLE; + break; + default: + dev_err(ds->dev, "invalid STP state: %d\n", state); + return; + } + + ksz_pwrite8(dev, port, P_STP_CTRL, data); +} + +static void ksz_port_fast_age(struct dsa_switch *ds, int port) +{ + struct ksz_device *dev = ds->priv; + u8 data8; + + ksz_read8(dev, REG_SW_LUE_CTRL_1, &data8); + data8 |= SW_FAST_AGING; + ksz_write8(dev, REG_SW_LUE_CTRL_1, data8); + + data8 &= ~SW_FAST_AGING; + ksz_write8(dev, REG_SW_LUE_CTRL_1, data8); +} + +static int ksz_port_vlan_filtering(struct dsa_switch *ds, int port, bool flag) +{ + struct ksz_device *dev = ds->priv; + + if (flag) { + ksz_port_cfg(dev, port, REG_PORT_LUE_CTRL, + PORT_VLAN_LOOKUP_VID_0, true); + ksz_cfg32(dev, REG_SW_QM_CTRL__4, UNICAST_VLAN_BOUNDARY, true); + ksz_cfg(dev, REG_SW_LUE_CTRL_0, SW_VLAN_ENABLE, true); + } else { + ksz_cfg(dev, REG_SW_LUE_CTRL_0, SW_VLAN_ENABLE, false); + ksz_cfg32(dev, REG_SW_QM_CTRL__4, UNICAST_VLAN_BOUNDARY, false); + ksz_port_cfg(dev, port, REG_PORT_LUE_CTRL, + PORT_VLAN_LOOKUP_VID_0, false); + } + + return 0; +} + +static int ksz_port_vlan_prepare(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan, + struct switchdev_trans *trans) +{ + /* nothing needed */ + + return 0; +} + +static void ksz_port_vlan_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan, + struct switchdev_trans *trans) +{ + struct ksz_device *dev = ds->priv; + u32 vlan_table[3]; + u16 vid; + bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; + + for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) { + if (get_vlan_table(ds, vid, vlan_table)) { + dev_dbg(dev->dev, "Failed to get vlan table\n"); + return; + } + + vlan_table[0] = VLAN_VALID | (vid & VLAN_FID_M); + if (untagged) + vlan_table[1] |= BIT(port); + else + vlan_table[1] &= ~BIT(port); + vlan_table[1] &= ~(BIT(dev->cpu_port)); + + vlan_table[2] |= BIT(port) | BIT(dev->cpu_port); + + if (set_vlan_table(ds, vid, vlan_table)) { + dev_dbg(dev->dev, "Failed to set vlan table\n"); + return; + } + + /* change PVID */ + if (vlan->flags & BRIDGE_VLAN_INFO_PVID) + ksz_pwrite16(dev, port, REG_PORT_DEFAULT_VID, vid); + } +} + +static int ksz_port_vlan_del(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_vlan *vlan) +{ + struct ksz_device *dev = ds->priv; + bool untagged = vlan->flags & BRIDGE_VLAN_INFO_UNTAGGED; + u32 vlan_table[3]; + u16 vid; + u16 pvid; + + ksz_pread16(dev, port, REG_PORT_DEFAULT_VID, &pvid); + pvid = pvid & 0xFFF; + + for (vid = vlan->vid_begin; vid <= vlan->vid_end; vid++) { + if (get_vlan_table(ds, vid, vlan_table)) { + dev_dbg(dev->dev, "Failed to get vlan table\n"); + return -ETIMEDOUT; + } + + vlan_table[2] &= ~BIT(port); + + if (pvid == vid) + pvid = 1; + + if (untagged) + vlan_table[1] &= ~BIT(port); + + if (set_vlan_table(ds, vid, vlan_table)) { + dev_dbg(dev->dev, "Failed to set vlan table\n"); + return -ETIMEDOUT; + } + } + + ksz_pwrite16(dev, port, REG_PORT_DEFAULT_VID, pvid); + + return 0; +} + +static int ksz_port_vlan_dump(struct dsa_switch *ds, int port, + struct switchdev_obj_port_vlan *vlan, + switchdev_obj_dump_cb_t *cb) +{ + struct ksz_device *dev = ds->priv; + u16 vid; + u16 data; + struct vlan_table *vlan_cache; + int err = 0; + + mutex_lock(&dev->vlan_mutex); + + /* use dev->vlan_cache due to lack of searching valid vlan entry */ + for (vid = vlan->vid_begin; vid < dev->num_vlans; vid++) { + vlan_cache = &dev->vlan_cache[vid]; + + if (!(vlan_cache->table[0] & VLAN_VALID)) + continue; + + vlan->vid_begin = vid; + vlan->vid_end = vid; + vlan->flags = 0; + if (vlan_cache->table[2] & BIT(port)) { + if (vlan_cache->table[1] & BIT(port)) + vlan->flags |= BRIDGE_VLAN_INFO_UNTAGGED; + ksz_pread16(dev, port, REG_PORT_DEFAULT_VID, &data); + if (vid == (data & 0xFFFFF)) + vlan->flags |= BRIDGE_VLAN_INFO_PVID; + + err = cb(&vlan->obj); + if (err) + break; + } + } + + mutex_unlock(&dev->vlan_mutex); + + return err; +} + +static int ksz_port_fdb_prepare(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_fdb *fdb, + struct switchdev_trans *trans) +{ + /* nothing needed */ + + return 0; +} + +struct alu_struct { + /* entry 1 */ + u8 is_static:1; + u8 is_src_filter:1; + u8 is_dst_filter:1; + u8 prio_age:3; + u32 _reserv_0_1:23; + u8 mstp:3; + /* entry 2 */ + u8 is_override:1; + u8 is_use_fid:1; + u32 _reserv_1_1:23; + u8 port_forward:7; + /* entry 3 & 4*/ + u32 _reserv_2_1:9; + u8 fid:7; + u8 mac[ETH_ALEN]; +}; + +static void ksz_port_fdb_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_fdb *fdb, + struct switchdev_trans *trans) +{ + struct ksz_device *dev = ds->priv; + u32 alu_table[4]; + u32 data; + + mutex_lock(&dev->alu_mutex); + + /* find any entry with mac & vid */ + data = fdb->vid << ALU_FID_INDEX_S; + data |= ((fdb->addr[0] << 8) | fdb->addr[1]); + ksz_write32(dev, REG_SW_ALU_INDEX_0, data); + + data = ((fdb->addr[2] << 24) | (fdb->addr[3] << 16)); + data |= ((fdb->addr[4] << 8) | fdb->addr[5]); + ksz_write32(dev, REG_SW_ALU_INDEX_1, data); + + /* start read operation */ + ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_READ | ALU_START); + + /* wait to be finished */ + if (wait_alu_ready(dev, ALU_START, 1000) < 0) { + dev_dbg(dev->dev, "Failed to read ALU\n"); + goto exit; + } + + /* read ALU entry */ + read_table(ds, alu_table); + + /* update ALU entry */ + alu_table[0] = ALU_V_STATIC_VALID; + alu_table[1] |= BIT(port); + if (fdb->vid) + alu_table[1] |= ALU_V_USE_FID; + alu_table[2] = (fdb->vid << ALU_V_FID_S); + alu_table[2] |= ((fdb->addr[0] << 8) | fdb->addr[1]); + alu_table[3] = ((fdb->addr[2] << 24) | (fdb->addr[3] << 16)); + alu_table[3] |= ((fdb->addr[4] << 8) | fdb->addr[5]); + + write_table(ds, alu_table); + + ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_WRITE | ALU_START); + + /* wait to be finished */ + if (wait_alu_ready(dev, ALU_START, 1000) < 0) + dev_dbg(dev->dev, "Failed to read ALU\n"); + +exit: + mutex_unlock(&dev->alu_mutex); +} + +static int ksz_port_fdb_del(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_fdb *fdb) +{ + struct ksz_device *dev = ds->priv; + u32 alu_table[4]; + u32 data; + int ret = 0; + + mutex_lock(&dev->alu_mutex); + + /* read any entry with mac & vid */ + data = fdb->vid << ALU_FID_INDEX_S; + data |= ((fdb->addr[0] << 8) | fdb->addr[1]); + ksz_write32(dev, REG_SW_ALU_INDEX_0, data); + + data = ((fdb->addr[2] << 24) | (fdb->addr[3] << 16)); + data |= ((fdb->addr[4] << 8) | fdb->addr[5]); + ksz_write32(dev, REG_SW_ALU_INDEX_1, data); + + /* start read operation */ + ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_READ | ALU_START); + + /* wait to be finished */ + ret = wait_alu_ready(dev, ALU_START, 1000); + if (ret < 0) { + dev_dbg(dev->dev, "Failed to read ALU\n"); + goto exit; + } + + ksz_read32(dev, REG_SW_ALU_VAL_A, &alu_table[0]); + if (alu_table[0] & ALU_V_STATIC_VALID) { + ksz_read32(dev, REG_SW_ALU_VAL_B, &alu_table[1]); + ksz_read32(dev, REG_SW_ALU_VAL_C, &alu_table[2]); + ksz_read32(dev, REG_SW_ALU_VAL_D, &alu_table[3]); + + /* clear forwarding port */ + alu_table[2] &= ~BIT(port); + + /* if there is no port to forward, clear table */ + if ((alu_table[2] & ALU_V_PORT_MAP) == 0) { + alu_table[0] = 0; + alu_table[1] = 0; + alu_table[2] = 0; + alu_table[3] = 0; + } + } else { + alu_table[0] = 0; + alu_table[1] = 0; + alu_table[2] = 0; + alu_table[3] = 0; + } + + write_table(ds, alu_table); + + ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_WRITE | ALU_START); + + /* wait to be finished */ + ret = wait_alu_ready(dev, ALU_START, 1000); + if (ret < 0) + dev_dbg(dev->dev, "Failed to write ALU\n"); + +exit: + mutex_unlock(&dev->alu_mutex); + + return ret; +} + +static void convert_alu(struct alu_struct *alu, u32 *alu_table) +{ + alu->is_static = !!(alu_table[0] & ALU_V_STATIC_VALID); + alu->is_src_filter = !!(alu_table[0] & ALU_V_SRC_FILTER); + alu->is_dst_filter = !!(alu_table[0] & ALU_V_DST_FILTER); + alu->prio_age = (alu_table[0] >> ALU_V_PRIO_AGE_CNT_S) & + ALU_V_PRIO_AGE_CNT_M; + alu->mstp = alu_table[0] & ALU_V_MSTP_M; + + alu->is_override = !!(alu_table[1] & ALU_V_OVERRIDE); + alu->is_use_fid = !!(alu_table[1] & ALU_V_USE_FID); + alu->port_forward = alu_table[1] & ALU_V_PORT_MAP; + + alu->fid = (alu_table[2] >> ALU_V_FID_S) & ALU_V_FID_M; + + alu->mac[0] = (alu_table[2] >> 8) & 0xFF; + alu->mac[1] = alu_table[2] & 0xFF; + alu->mac[2] = (alu_table[3] >> 24) & 0xFF; + alu->mac[3] = (alu_table[3] >> 16) & 0xFF; + alu->mac[4] = (alu_table[3] >> 8) & 0xFF; + alu->mac[5] = alu_table[3] & 0xFF; +} + +static int ksz_port_fdb_dump(struct dsa_switch *ds, int port, + struct switchdev_obj_port_fdb *fdb, + switchdev_obj_dump_cb_t *cb) +{ + struct ksz_device *dev = ds->priv; + int ret = 0; + u32 data; + u32 alu_table[4]; + struct alu_struct alu; + int timeout; + + mutex_lock(&dev->alu_mutex); + + /* start ALU search */ + ksz_write32(dev, REG_SW_ALU_CTRL__4, ALU_START | ALU_SEARCH); + + do { + timeout = 1000; + do { + ksz_read32(dev, REG_SW_ALU_CTRL__4, &data); + if ((data & ALU_VALID) || !(data & ALU_START)) + break; + usleep_range(1, 10); + } while (timeout-- > 0); + + if (!timeout) { + dev_dbg(dev->dev, "Failed to search ALU\n"); + ret = -ETIMEDOUT; + goto exit; + } + + /* read ALU table */ + read_table(ds, alu_table); + + convert_alu(&alu, alu_table); + + if (alu.port_forward & BIT(port)) { + fdb->vid = alu.fid; + if (alu.is_static) + fdb->ndm_state = NUD_NOARP; + else + fdb->ndm_state = NUD_REACHABLE; + ether_addr_copy(fdb->addr, alu.mac); + + ret = cb(&fdb->obj); + if (ret) + goto exit; + } + } while (data & ALU_START); + +exit: + + /* stop ALU search */ + ksz_write32(dev, REG_SW_ALU_CTRL__4, 0); + + mutex_unlock(&dev->alu_mutex); + + return ret; +} + +static int ksz_port_mdb_prepare(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb, + struct switchdev_trans *trans) +{ + /* nothing to do */ + return 0; +} + +static void ksz_port_mdb_add(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb, + struct switchdev_trans *trans) +{ + struct ksz_device *dev = ds->priv; + u32 static_table[4]; + u32 data; + int index; + u32 mac_hi, mac_lo; + + mac_hi = ((mdb->addr[0] << 8) | mdb->addr[1]); + mac_lo = ((mdb->addr[2] << 24) | (mdb->addr[3] << 16)); + mac_lo |= ((mdb->addr[4] << 8) | mdb->addr[5]); + + mutex_lock(&dev->alu_mutex); + + for (index = 0; index < dev->num_statics; index++) { + /* find empty slot first */ + data = (index << ALU_STAT_INDEX_S) | + ALU_STAT_READ | ALU_STAT_START; + ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data); + + /* wait to be finished */ + if (wait_alu_sta_ready(dev, ALU_STAT_START, 1000) < 0) { + dev_dbg(dev->dev, "Failed to read ALU STATIC\n"); + goto exit; + } + + /* read ALU static table */ + read_table(ds, static_table); + + if (static_table[0] & ALU_V_STATIC_VALID) { + /* check this has same vid & mac address */ + if (((static_table[2] >> ALU_V_FID_S) == (mdb->vid)) && + ((static_table[2] & ALU_V_MAC_ADDR_HI) == mac_hi) && + (static_table[3] == mac_lo)) { + /* found matching one */ + break; + } + } else { + /* found empty one */ + break; + } + } + + /* no available entry */ + if (index == dev->num_statics) + goto exit; + + /* add entry */ + static_table[0] = ALU_V_STATIC_VALID; + static_table[1] |= BIT(port); + if (mdb->vid) + static_table[1] |= ALU_V_USE_FID; + static_table[2] = (mdb->vid << ALU_V_FID_S); + static_table[2] |= mac_hi; + static_table[3] = mac_lo; + + write_table(ds, static_table); + + data = (index << ALU_STAT_INDEX_S) | ALU_STAT_START; + ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data); + + /* wait to be finished */ + if (wait_alu_sta_ready(dev, ALU_STAT_START, 1000) < 0) + dev_dbg(dev->dev, "Failed to read ALU STATIC\n"); + +exit: + mutex_unlock(&dev->alu_mutex); +} + +static int ksz_port_mdb_del(struct dsa_switch *ds, int port, + const struct switchdev_obj_port_mdb *mdb) +{ + struct ksz_device *dev = ds->priv; + u32 static_table[4]; + u32 data; + int index; + int ret = 0; + u32 mac_hi, mac_lo; + + mac_hi = ((mdb->addr[0] << 8) | mdb->addr[1]); + mac_lo = ((mdb->addr[2] << 24) | (mdb->addr[3] << 16)); + mac_lo |= ((mdb->addr[4] << 8) | mdb->addr[5]); + + mutex_lock(&dev->alu_mutex); + + for (index = 0; index < dev->num_statics; index++) { + /* find empty slot first */ + data = (index << ALU_STAT_INDEX_S) | + ALU_STAT_READ | ALU_STAT_START; + ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data); + + /* wait to be finished */ + ret = wait_alu_sta_ready(dev, ALU_STAT_START, 1000); + if (ret < 0) { + dev_dbg(dev->dev, "Failed to read ALU STATIC\n"); + goto exit; + } + + /* read ALU static table */ + read_table(ds, static_table); + + if (static_table[0] & ALU_V_STATIC_VALID) { + /* check this has same vid & mac address */ + + if (((static_table[2] >> ALU_V_FID_S) == (mdb->vid)) && + ((static_table[2] & ALU_V_MAC_ADDR_HI) == mac_hi) && + (static_table[3] == mac_lo)) { + /* found matching one */ + break; + } + } + } + + /* no available entry */ + if (index == dev->num_statics) { + ret = -EINVAL; + goto exit; + } + + /* clear port */ + static_table[1] &= ~BIT(port); + + if ((static_table[1] & ALU_V_PORT_MAP) == 0) { + /* delete entry */ + static_table[0] = 0; + static_table[1] = 0; + static_table[2] = 0; + static_table[3] = 0; + } + + write_table(ds, static_table); + + data = (index << ALU_STAT_INDEX_S) | ALU_STAT_START; + ksz_write32(dev, REG_SW_ALU_STAT_CTRL__4, data); + + /* wait to be finished */ + ret = wait_alu_sta_ready(dev, ALU_STAT_START, 1000); + if (ret < 0) + dev_dbg(dev->dev, "Failed to read ALU STATIC\n"); + +exit: + mutex_unlock(&dev->alu_mutex); + + return ret; +} + +static int ksz_port_mdb_dump(struct dsa_switch *ds, int port, + struct switchdev_obj_port_mdb *mdb, + switchdev_obj_dump_cb_t *cb) +{ + /* this is not called by switch layer */ + return 0; +} + +static int ksz_port_mirror_add(struct dsa_switch *ds, int port, + struct dsa_mall_mirror_tc_entry *mirror, + bool ingress) +{ + struct ksz_device *dev = ds->priv; + + if (ingress) + ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, true); + else + ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, true); + + ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_SNIFFER, false); + + /* configure mirror port */ + ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL, + PORT_MIRROR_SNIFFER, true); + + ksz_cfg(dev, S_MIRROR_CTRL, SW_MIRROR_RX_TX, false); + + return 0; +} + +static void ksz_port_mirror_del(struct dsa_switch *ds, int port, + struct dsa_mall_mirror_tc_entry *mirror) +{ + struct ksz_device *dev = ds->priv; + u8 data; + + if (mirror->ingress) + ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_RX, false); + else + ksz_port_cfg(dev, port, P_MIRROR_CTRL, PORT_MIRROR_TX, false); + + ksz_pread8(dev, port, P_MIRROR_CTRL, &data); + + if (!(data & (PORT_MIRROR_RX | PORT_MIRROR_TX))) + ksz_port_cfg(dev, mirror->to_local_port, P_MIRROR_CTRL, + PORT_MIRROR_SNIFFER, false); +} + +static const struct dsa_switch_ops ksz_switch_ops = { + .get_tag_protocol = ksz_get_tag_protocol, + .setup = ksz_setup, + .phy_read = ksz_phy_read16, + .phy_write = ksz_phy_write16, + .port_enable = ksz_enable_port, + .port_disable = ksz_disable_port, + .get_strings = ksz_get_strings, + .get_ethtool_stats = ksz_get_ethtool_stats, + .get_sset_count = ksz_sset_count, + .port_stp_state_set = ksz_port_stp_state_set, + .port_fast_age = ksz_port_fast_age, + .port_vlan_filtering = ksz_port_vlan_filtering, + .port_vlan_prepare = ksz_port_vlan_prepare, + .port_vlan_add = ksz_port_vlan_add, + .port_vlan_del = ksz_port_vlan_del, + .port_vlan_dump = ksz_port_vlan_dump, + .port_fdb_prepare = ksz_port_fdb_prepare, + .port_fdb_dump = ksz_port_fdb_dump, + .port_fdb_add = ksz_port_fdb_add, + .port_fdb_del = ksz_port_fdb_del, + .port_mdb_prepare = ksz_port_mdb_prepare, + .port_mdb_add = ksz_port_mdb_add, + .port_mdb_del = ksz_port_mdb_del, + .port_mdb_dump = ksz_port_mdb_dump, + .port_mirror_add = ksz_port_mirror_add, + .port_mirror_del = ksz_port_mirror_del, +}; + +struct ksz_chip_data { + u32 chip_id; + const char *dev_name; + int num_vlans; + int num_alus; + int num_statics; + int cpu_ports; + int port_cnt; +}; + +static const struct ksz_chip_data ksz_switch_chips[] = { + { + .chip_id = 0x00947700, + .dev_name = "KSZ9477", + .num_vlans = 4096, + .num_alus = 4096, + .num_statics = 16, + .cpu_ports = 0x7F, /* can be configured as cpu port */ + .port_cnt = 7, /* total physical port count */ + }, +}; + +static int ksz_switch_init(struct ksz_device *dev) +{ + int i; + + mutex_init(&dev->reg_mutex); + mutex_init(&dev->stats_mutex); + mutex_init(&dev->alu_mutex); + mutex_init(&dev->vlan_mutex); + + dev->ds->ops = &ksz_switch_ops; + + for (i = 0; i < ARRAY_SIZE(ksz_switch_chips); i++) { + const struct ksz_chip_data *chip = &ksz_switch_chips[i]; + + if (dev->chip_id == chip->chip_id) { + dev->name = chip->dev_name; + dev->num_vlans = chip->num_vlans; + dev->num_alus = chip->num_alus; + dev->num_statics = chip->num_statics; + dev->port_cnt = chip->port_cnt; + dev->cpu_ports = chip->cpu_ports; + + break; + } + } + + /* no switch found */ + if (!dev->port_cnt) + return -ENODEV; + + return 0; +} + +struct ksz_device *ksz_switch_alloc(struct device *base, + const struct ksz_io_ops *ops, + void *priv) +{ + struct dsa_switch *ds; + struct ksz_device *swdev; + + ds = dsa_switch_alloc(base, DSA_MAX_PORTS); + if (!ds) + return NULL; + + swdev = devm_kzalloc(base, sizeof(*swdev), GFP_KERNEL); + if (!swdev) + return NULL; + + ds->priv = swdev; + swdev->dev = base; + + swdev->ds = ds; + swdev->priv = priv; + swdev->ops = ops; + + return swdev; +} +EXPORT_SYMBOL(ksz_switch_alloc); + +int ksz_switch_detect(struct ksz_device *dev) +{ + u8 data8; + u32 id32; + int ret; + + /* turn off SPI DO Edge select */ + ret = ksz_read8(dev, REG_SW_GLOBAL_SERIAL_CTRL_0, &data8); + if (ret) + return ret; + + data8 &= ~SPI_AUTO_EDGE_DETECTION; + ret = ksz_write8(dev, REG_SW_GLOBAL_SERIAL_CTRL_0, data8); + if (ret) + return ret; + + /* read chip id */ + ret = ksz_read32(dev, REG_CHIP_ID0__1, &id32); + if (ret) + return ret; + + dev->chip_id = id32; + + return 0; +} +EXPORT_SYMBOL(ksz_switch_detect); + +int ksz_switch_register(struct ksz_device *dev) +{ + int ret; + + if (dev->pdata) + dev->chip_id = dev->pdata->chip_id; + + if (ksz_switch_detect(dev)) + return -EINVAL; + + ret = ksz_switch_init(dev); + if (ret) + return ret; + + return dsa_register_switch(dev->ds); +} +EXPORT_SYMBOL(ksz_switch_register); + +void ksz_switch_remove(struct ksz_device *dev) +{ + dsa_unregister_switch(dev->ds); +} +EXPORT_SYMBOL(ksz_switch_remove); + +MODULE_AUTHOR("Woojung Huh "); +MODULE_DESCRIPTION("Microchip KSZ Series Switch DSA Driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/net/dsa/microchip/ksz_priv.h b/drivers/net/dsa/microchip/ksz_priv.h new file mode 100644 index 000000000000..2a98dbd51456 --- /dev/null +++ b/drivers/net/dsa/microchip/ksz_priv.h @@ -0,0 +1,210 @@ +/* + * Microchip KSZ series switch common definitions + * + * Copyright (C) 2017 + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef __KSZ_PRIV_H +#define __KSZ_PRIV_H + +#include +#include +#include +#include +#include + +#include "ksz_9477_reg.h" + +struct ksz_io_ops; + +struct vlan_table { + u32 table[3]; +}; + +struct ksz_device { + struct dsa_switch *ds; + struct ksz_platform_data *pdata; + const char *name; + + struct mutex reg_mutex; /* register access */ + struct mutex stats_mutex; /* status access */ + struct mutex alu_mutex; /* ALU access */ + struct mutex vlan_mutex; /* vlan access */ + const struct ksz_io_ops *ops; + + struct device *dev; + + void *priv; + + /* chip specific data */ + u32 chip_id; + int num_vlans; + int num_alus; + int num_statics; + int cpu_port; /* port connected to CPU */ + int cpu_ports; /* port bitmap can be cpu port */ + int port_cnt; + + struct vlan_table *vlan_cache; + + u64 mib_value[TOTAL_SWITCH_COUNTER_NUM]; +}; + +struct ksz_io_ops { + int (*read8)(struct ksz_device *dev, u32 reg, u8 *value); + int (*read16)(struct ksz_device *dev, u32 reg, u16 *value); + int (*read24)(struct ksz_device *dev, u32 reg, u32 *value); + int (*read32)(struct ksz_device *dev, u32 reg, u32 *value); + int (*write8)(struct ksz_device *dev, u32 reg, u8 value); + int (*write16)(struct ksz_device *dev, u32 reg, u16 value); + int (*write24)(struct ksz_device *dev, u32 reg, u32 value); + int (*write32)(struct ksz_device *dev, u32 reg, u32 value); + int (*phy_read16)(struct ksz_device *dev, int addr, int reg, + u16 *value); + int (*phy_write16)(struct ksz_device *dev, int addr, int reg, + u16 value); +}; + +struct ksz_device *ksz_switch_alloc(struct device *base, + const struct ksz_io_ops *ops, void *priv); +int ksz_switch_detect(struct ksz_device *dev); +int ksz_switch_register(struct ksz_device *dev); +void ksz_switch_remove(struct ksz_device *dev); + +static inline int ksz_read8(struct ksz_device *dev, u32 reg, u8 *val) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->read8(dev, reg, val); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline int ksz_read16(struct ksz_device *dev, u32 reg, u16 *val) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->read16(dev, reg, val); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline int ksz_read24(struct ksz_device *dev, u32 reg, u32 *val) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->read24(dev, reg, val); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline int ksz_read32(struct ksz_device *dev, u32 reg, u32 *val) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->read32(dev, reg, val); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline int ksz_write8(struct ksz_device *dev, u32 reg, u8 value) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->write8(dev, reg, value); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline int ksz_write16(struct ksz_device *dev, u32 reg, u16 value) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->write16(dev, reg, value); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline int ksz_write24(struct ksz_device *dev, u32 reg, u32 value) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->write24(dev, reg, value); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline int ksz_write32(struct ksz_device *dev, u32 reg, u32 value) +{ + int ret; + + mutex_lock(&dev->reg_mutex); + ret = dev->ops->write32(dev, reg, value); + mutex_unlock(&dev->reg_mutex); + + return ret; +} + +static inline void ksz_pread8(struct ksz_device *dev, int port, int offset, + u8 *data) +{ + ksz_read8(dev, PORT_CTRL_ADDR(port, offset), data); +} + +static inline void ksz_pread16(struct ksz_device *dev, int port, int offset, + u16 *data) +{ + ksz_read16(dev, PORT_CTRL_ADDR(port, offset), data); +} + +static inline void ksz_pread32(struct ksz_device *dev, int port, int offset, + u32 *data) +{ + ksz_read32(dev, PORT_CTRL_ADDR(port, offset), data); +} + +static inline void ksz_pwrite8(struct ksz_device *dev, int port, int offset, + u8 data) +{ + ksz_write8(dev, PORT_CTRL_ADDR(port, offset), data); +} + +static inline void ksz_pwrite16(struct ksz_device *dev, int port, int offset, + u16 data) +{ + ksz_write16(dev, PORT_CTRL_ADDR(port, offset), data); +} + +static inline void ksz_pwrite32(struct ksz_device *dev, int port, int offset, + u32 data) +{ + ksz_write32(dev, PORT_CTRL_ADDR(port, offset), data); +} + +#endif diff --git a/drivers/net/dsa/microchip/ksz_spi.c b/drivers/net/dsa/microchip/ksz_spi.c new file mode 100644 index 000000000000..c51946983bed --- /dev/null +++ b/drivers/net/dsa/microchip/ksz_spi.c @@ -0,0 +1,216 @@ +/* + * Microchip KSZ series register access through SPI + * + * Copyright (C) 2017 + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#include + +#include +#include +#include +#include + +#include "ksz_priv.h" + +/* SPI frame opcodes */ +#define KS_SPIOP_RD 3 +#define KS_SPIOP_WR 2 + +#define SPI_ADDR_SHIFT 24 +#define SPI_ADDR_MASK (BIT(SPI_ADDR_SHIFT) - 1) +#define SPI_TURNAROUND_SHIFT 5 + +static int ksz_spi_read_reg(struct spi_device *spi, u32 reg, u8 *val, + unsigned int len) +{ + u32 txbuf; + int ret; + + txbuf = reg & SPI_ADDR_MASK; + txbuf |= KS_SPIOP_RD << SPI_ADDR_SHIFT; + txbuf <<= SPI_TURNAROUND_SHIFT; + txbuf = cpu_to_be32(txbuf); + + ret = spi_write_then_read(spi, &txbuf, 4, val, len); + return ret; +} + +static int ksz_spi_read(struct ksz_device *dev, u32 reg, u8 *data, + unsigned int len) +{ + struct spi_device *spi = dev->priv; + + return ksz_spi_read_reg(spi, reg, data, len); +} + +static int ksz_spi_read8(struct ksz_device *dev, u32 reg, u8 *val) +{ + return ksz_spi_read(dev, reg, val, 1); +} + +static int ksz_spi_read16(struct ksz_device *dev, u32 reg, u16 *val) +{ + int ret = ksz_spi_read(dev, reg, (u8 *)val, 2); + + if (!ret) + *val = be16_to_cpu(*val); + + return ret; +} + +static int ksz_spi_read24(struct ksz_device *dev, u32 reg, u32 *val) +{ + int ret; + + *val = 0; + ret = ksz_spi_read(dev, reg, (u8 *)val, 3); + if (!ret) { + *val = be32_to_cpu(*val); + /* convert to 24bit */ + *val >>= 8; + } + + return ret; +} + +static int ksz_spi_read32(struct ksz_device *dev, u32 reg, u32 *val) +{ + int ret = ksz_spi_read(dev, reg, (u8 *)val, 4); + + if (!ret) + *val = be32_to_cpu(*val); + + return ret; +} + +static int ksz_spi_write_reg(struct spi_device *spi, u32 reg, u8 *val, + unsigned int len) +{ + u32 txbuf; + u8 data[12]; + int i; + + txbuf = reg & SPI_ADDR_MASK; + txbuf |= (KS_SPIOP_WR << SPI_ADDR_SHIFT); + txbuf <<= SPI_TURNAROUND_SHIFT; + txbuf = cpu_to_be32(txbuf); + + data[0] = txbuf & 0xFF; + data[1] = (txbuf & 0xFF00) >> 8; + data[2] = (txbuf & 0xFF0000) >> 16; + data[3] = (txbuf & 0xFF000000) >> 24; + for (i = 0; i < len; i++) + data[i + 4] = val[i]; + + return spi_write(spi, &data, 4 + len); +} + +static int ksz_spi_write8(struct ksz_device *dev, u32 reg, u8 value) +{ + struct spi_device *spi = dev->priv; + + return ksz_spi_write_reg(spi, reg, &value, 1); +} + +static int ksz_spi_write16(struct ksz_device *dev, u32 reg, u16 value) +{ + struct spi_device *spi = dev->priv; + + value = cpu_to_be16(value); + return ksz_spi_write_reg(spi, reg, (u8 *)&value, 2); +} + +static int ksz_spi_write24(struct ksz_device *dev, u32 reg, u32 value) +{ + struct spi_device *spi = dev->priv; + + /* make it to big endian 24bit from MSB */ + value <<= 8; + value = cpu_to_be32(value); + return ksz_spi_write_reg(spi, reg, (u8 *)&value, 3); +} + +static int ksz_spi_write32(struct ksz_device *dev, u32 reg, u32 value) +{ + struct spi_device *spi = dev->priv; + + value = cpu_to_be32(value); + return ksz_spi_write_reg(spi, reg, (u8 *)&value, 4); +} + +static const struct ksz_io_ops ksz_spi_ops = { + .read8 = ksz_spi_read8, + .read16 = ksz_spi_read16, + .read24 = ksz_spi_read24, + .read32 = ksz_spi_read32, + .write8 = ksz_spi_write8, + .write16 = ksz_spi_write16, + .write24 = ksz_spi_write24, + .write32 = ksz_spi_write32, +}; + +static int ksz_spi_probe(struct spi_device *spi) +{ + struct ksz_device *dev; + int ret; + + dev = ksz_switch_alloc(&spi->dev, &ksz_spi_ops, spi); + if (!dev) + return -ENOMEM; + + if (spi->dev.platform_data) + dev->pdata = spi->dev.platform_data; + + ret = ksz_switch_register(dev); + if (ret) + return ret; + + spi_set_drvdata(spi, dev); + + return 0; +} + +static int ksz_spi_remove(struct spi_device *spi) +{ + struct ksz_device *dev = spi_get_drvdata(spi); + + if (dev) + ksz_switch_remove(dev); + + return 0; +} + +static const struct of_device_id ksz_dt_ids[] = { + { .compatible = "microchip,ksz9477" }, + {}, +}; +MODULE_DEVICE_TABLE(of, ksz_dt_ids); + +static struct spi_driver ksz_spi_driver = { + .driver = { + .name = "ksz9477-switch", + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(ksz_dt_ids), + }, + .probe = ksz_spi_probe, + .remove = ksz_spi_remove, +}; + +module_spi_driver(ksz_spi_driver); + +MODULE_AUTHOR("Woojung Huh "); +MODULE_DESCRIPTION("Microchip KSZ Series Switch SPI access Driver"); +MODULE_LICENSE("GPL"); diff --git a/include/linux/platform_data/microchip-ksz.h b/include/linux/platform_data/microchip-ksz.h new file mode 100644 index 000000000000..84789ca634aa --- /dev/null +++ b/include/linux/platform_data/microchip-ksz.h @@ -0,0 +1,29 @@ +/* + * Microchip KSZ series switch platform data + * + * Copyright (C) 2017 + * + * Permission to use, copy, modify, and/or distribute this software for any + * purpose with or without fee is hereby granted, provided that the above + * copyright notice and this permission notice appear in all copies. + * + * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES + * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF + * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR + * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES + * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN + * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF + * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. + */ + +#ifndef __MICROCHIP_KSZ_H +#define __MICROCHIP_KSZ_H + +#include + +struct ksz_platform_data { + u32 chip_id; + u16 enabled_ports; +}; + +#endif