From: Tomasz Figa Date: Fri, 16 Nov 2012 14:28:17 +0000 (+0100) Subject: mmc: host: sdhci-s3c: Add support for pinctrl X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=b96efccb8fc9939605599e5b2c026644973cc92d;p=openwrt%2Fstaging%2Fblogic.git mmc: host: sdhci-s3c: Add support for pinctrl This patch adds support for pin configuration using pinctrl subsystem to the sdhci-s3c driver. Signed-off-by: Tomasz Figa Acked-by: Thomas Abraham Signed-off-by: Chris Ball --- diff --git a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt index 630a7d7f4718..97e9e315400d 100644 --- a/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt +++ b/Documentation/devicetree/bindings/mmc/samsung-sdhci.txt @@ -12,10 +12,6 @@ is used. The Samsung's SDHCI controller bindings extends this as listed below. [A] The property "samsung,cd-pinmux-gpio" can be used as stated in the "Optional Board Specific Properties" section below. -[B] If core card-detect bindings and "samsung,cd-pinmux-gpio" property - is not specified, it is assumed that there is no card detection - mechanism used. - Required SoC Specific Properties: - compatible: should be one of the following - "samsung,s3c6410-sdhci": For controllers compatible with s3c6410 sdhci @@ -24,14 +20,18 @@ Required SoC Specific Properties: controller. Required Board Specific Properties: -- gpios: Should specify the gpios used for clock, command and data lines. The - gpio specifier format depends on the gpio controller. +- Samsung GPIO variant (will be completely replaced by pinctrl): + - gpios: Should specify the gpios used for clock, command and data lines. The + gpio specifier format depends on the gpio controller. +- Pinctrl variant (preferred if available): + - pinctrl-0: Should specify pin control groups used for this controller. + - pinctrl-names: Should contain only one value - "default". Optional Board Specific Properties: - samsung,cd-pinmux-gpio: Specifies the card detect line that is routed through a pinmux to the card-detect pin of the card slot. This property should be used only if none of the mmc core card-detect properties are - used. + used. Only for Samsung GPIO variant. Example: sdhci@12530000 { @@ -40,12 +40,18 @@ Example: interrupts = <0 75 0>; bus-width = <4>; cd-gpios = <&gpk2 2 2 3 3>; + + /* Samsung GPIO variant */ gpios = <&gpk2 0 2 0 3>, /* clock line */ <&gpk2 1 2 0 3>, /* command line */ <&gpk2 3 2 3 3>, /* data line 0 */ <&gpk2 4 2 3 3>, /* data line 1 */ <&gpk2 5 2 3 3>, /* data line 2 */ <&gpk2 6 2 3 3>; /* data line 3 */ + + /* Pinctrl variant */ + pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4>; + pinctrl-names = "default"; }; Note: This example shows both SoC specific and board specific properties diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c index 93c5d62fcaff..99697696e7eb 100644 --- a/drivers/mmc/host/sdhci-s3c.c +++ b/drivers/mmc/host/sdhci-s3c.c @@ -24,6 +24,7 @@ #include #include #include +#include #include @@ -57,6 +58,7 @@ struct sdhci_s3c { int ext_cd_irq; int ext_cd_gpio; int *gpios; + struct pinctrl *pctrl; struct clk *clk_io; struct clk *clk_bus[MAX_BUS_CLK]; @@ -484,8 +486,9 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev, return -EINVAL; } - dev_info(dev, "assuming no card detect line available\n"); - pdata->cd_type = S3C_SDHCI_CD_NONE; + /* assuming internal card detect that will be configured by pinctrl */ + pdata->cd_type = S3C_SDHCI_CD_INTERNAL; + goto setup_bus; found_cd: if (pdata->cd_type == S3C_SDHCI_CD_GPIO) { @@ -503,6 +506,9 @@ static int __devinit sdhci_s3c_parse_dt(struct device *dev, } setup_bus: + if (!IS_ERR(ourhost->pctrl)) + return 0; + /* get the gpios for command, clock and data lines */ for (cnt = 0; cnt < NUM_GPIOS(pdata->max_width); cnt++) { gpio = of_get_gpio(node, cnt); @@ -581,6 +587,8 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev) goto err_pdata_io_clk; } + sc->pctrl = devm_pinctrl_get_select_default(&pdev->dev); + if (pdev->dev.of_node) { ret = sdhci_s3c_parse_dt(&pdev->dev, host, pdata); if (ret)