From: Serg Studzinskii Date: Wed, 8 Mar 2017 20:10:05 +0000 (+0200) Subject: ar71xx: add support for TP-Link TL-WR942N v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=b7cc6616152a12b3f68c5f36e9ef052da5de889e;p=openwrt%2Fstaging%2Fadrian.git ar71xx: add support for TP-Link TL-WR942N v1 TP-Link TL-WR942N v1 is a 2.4 GHz single-band N450 router, based on Qualcomm/Atheros QCA9561. Specification: - 775/650/258 MHz (CPU/DDR/AHB) - 128 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 3T3R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x USB 2.0 - 11x LED (most are controlled by 74HC595) - 2x button - UART header on PCB* * Serial console is disabled in OEM non-beta firmwares and corresponding GPIO pins 14 and 15 are assigned to control USB1 and USB2 LEDs by production (non-beta) U-Boot and firmware. Currently not working: 1. USB1 and USB2 LEDs if UART RX and TX pins are assigned to their GPIOs by some U-Boot versions. Flash instruction under vendor GUI: 1. Download "lede-ar71xx-generic-tl-wr942n-v1-squashfs-factory.bin". 2. Go to WEB interface and perform usual firmware upgrade. FLash instruction under U-Boot recovery mode (doesn't work in beta firmware): 1. Setup PC with static IP "192.168.0.66/24" and tftp server. 2. Change "*-factory" image filename to "WR942v1_recovery.bin" and make it available to download from your tftp server. 3. Press "reset" button and power up the router, wait till "WPS" LED turns on. Flash instruction under U-Boot, using UART (can be done only with preinstalled UART-enabled U-Boot version!): 1. Use "tpl" to stop autobooting and obtain U-Boot CLI access. 2. Setup ip addresses for U-Boot and your tftp server. 3. Issue below commands: tftp 0x81000000 lede-ar71xx-generic-tl-wr942n-v1-sysupgrade.bin erase 0x9f020000 +$filesize cp.b 0x81000000 0x9f020000 $filesize reset Signed-off-by: Serg Studzinskii [minor code style fixes, extended commit message] Signed-off-by: Piotr Dymacz --- diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 2f9ae8b10e..be6dfcc968 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -745,6 +745,16 @@ tl-wr840n-v3) ucidef_set_led_switch "lan" "LAN" "tp-link:green:lan" "switch0" "0x1E" ucidef_set_led_wlan "wlan" "WLAN" "tp-link:green:wlan" "phy0tpt" ;; +tl-wr942n-v1) + ucidef_set_led_switch "lan1" "LAN1" "$board:green:lan1" "switch0" "0x04" + ucidef_set_led_switch "lan2" "LAN2" "$board:green:lan2" "switch0" "0x08" + ucidef_set_led_switch "lan3" "LAN3" "$board:green:lan3" "switch0" "0x10" + ucidef_set_led_switch "lan4" "LAN4" "$board:green:lan4" "switch0" "0x02" + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0" + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ucidef_set_led_usbdev "usb1" "USB1" "$board:green:usb1" "1-1.2" + ucidef_set_led_usbdev "usb2" "USB2" "$board:green:usb2" "1-1.1" + ;; tl-wr1043nd|\ tl-wr1043nd-v2) ucidef_set_led_usbdev "usb" "USB" "tp-link:green:usb" "1-1" diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index 0dc8bf31a8..b805487977 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -411,7 +411,8 @@ ar71xx_setup_interfaces() tl-mr3420-v2|\ tl-wr841n-v8|\ tl-wr842n-v2|\ - tl-wr941nd-v5) + tl-wr941nd-v5|\ + tl-wr942n-v1) ucidef_set_interfaces_lan_wan "eth1.1" "eth0" ucidef_add_switch "switch0" \ "0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3" diff --git a/target/linux/ar71xx/base-files/etc/diag.sh b/target/linux/ar71xx/base-files/etc/diag.sh index ae43351c6a..369abde9d4 100644 --- a/target/linux/ar71xx/base-files/etc/diag.sh +++ b/target/linux/ar71xx/base-files/etc/diag.sh @@ -36,6 +36,7 @@ get_status_led() { db120|\ dr344|\ tew-632brp|\ + tl-wr942n-v1|\ wpj344|\ zbt-we1526) status_led="$board:green:status" diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index e781c6ee7e..5660d3eaa9 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -1166,6 +1166,9 @@ ar71xx_board_detect() { *"TL-WR941ND") name="tl-wr941nd" ;; + *"TL-WR942N v1") + name="tl-wr942n-v1" + ;; *"Tube2H") name="tube2h" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 16701f64ca..e14f8f3e49 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -271,6 +271,7 @@ platform_check_image() { tew-712br|\ tew-732br|\ tew-823dru|\ + tl-wr942n-v1|\ unifi-outdoor|\ unifiac-lite|\ unifiac-pro|\ diff --git a/target/linux/ar71xx/config-4.4 b/target/linux/ar71xx/config-4.4 index 43a487d20e..df1108d904 100644 --- a/target/linux/ar71xx/config-4.4 +++ b/target/linux/ar71xx/config-4.4 @@ -209,6 +209,7 @@ CONFIG_ATH79_MACH_TL_WR841N_V9=y CONFIG_ATH79_MACH_TL_WR941ND=y CONFIG_ATH79_MACH_TL_WR941ND_V6=y CONFIG_ATH79_MACH_TL_WR940N_V4=y +CONFIG_ATH79_MACH_TL_WR942N_V1=y CONFIG_ATH79_MACH_TUBE2H=y CONFIG_ATH79_MACH_UBNT=y CONFIG_ATH79_MACH_UBNT_UNIFIAC=y diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index c18eec557d..ae64c6e92e 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -1695,6 +1695,17 @@ config ATH79_MACH_TL_WR940N_V4 select ATH79_DEV_M25P80 select ATH79_DEV_WMAC +config ATH79_MACH_TL_WR942N_V1 + bool "TP-LINK TL-WR942N v1 support" + select SOC_QCA956X + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_M25P80 + select ATH79_DEV_USB + select ATH79_DEV_WMAC + select ATH79_NVRAM + config ATH79_MACH_TL_WR1041N_V2 bool "TP-LINK TL-WR1041N v2 support" select SOC_AR934X diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index 55c5a2a939..bf5515b4f3 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -214,6 +214,7 @@ obj-$(CONFIG_ATH79_MACH_TL_WR841N_V9) += mach-tl-wr841n-v9.o obj-$(CONFIG_ATH79_MACH_TL_WR941ND) += mach-tl-wr941nd.o obj-$(CONFIG_ATH79_MACH_TL_WR941ND_V6) += mach-tl-wr941nd-v6.o obj-$(CONFIG_ATH79_MACH_TL_WR940N_V4) += mach-tl-wr940n-v4.o +obj-$(CONFIG_ATH79_MACH_TL_WR942N_V1) += mach-tl-wr942n-v1.o obj-$(CONFIG_ATH79_MACH_TUBE2H) += mach-tube2h.o obj-$(CONFIG_ATH79_MACH_UBNT) += mach-ubnt.o obj-$(CONFIG_ATH79_MACH_UBNT_UNIFIAC) += mach-ubnt-unifiac.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c new file mode 100644 index 0000000000..72910400c5 --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-tl-wr942n-v1.c @@ -0,0 +1,279 @@ +/* + * TP-Link TL-WR942N(RU) v1 board support + * + * Copyright (C) 2017 Sergey Studzinski + * Thanks to Henryk Heisig + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include "common.h" +#include "dev-m25p80.h" +#include "machtypes.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-spi.h" +#include "dev-usb.h" +#include "dev-wmac.h" +#include "nvram.h" + +#define TL_WR942N_V1_KEYS_POLL_INTERVAL 20 +#define TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL \ + (3 * TL_WR942N_V1_KEYS_POLL_INTERVAL) + +#define TL_WR942N_V1_GPIO_BTN_RESET 1 +#define TL_WR942N_V1_GPIO_BTN_RFKILL 2 + +#define TL_WR942N_V1_GPIO_UART_TX 4 +#define TL_WR942N_V1_GPIO_UART_RX 5 + +#define TL_WR942N_V1_GPIO_LED_USB2 14 +#define TL_WR942N_V1_GPIO_LED_USB1 15 + +#define TL_WR942N_V1_GPIO_SHIFT_OE 16 +#define TL_WR942N_V1_GPIO_SHIFT_SER 17 +#define TL_WR942N_V1_GPIO_SHIFT_SRCLK 18 +#define TL_WR942N_V1_GPIO_SHIFT_SRCLR 19 +#define TL_WR942N_V1_GPIO_SHIFT_RCLK 20 +#define TL_WR942N_V1_GPIO_LED_WPS 21 +#define TL_WR942N_V1_GPIO_LED_STATUS 22 + +#define TL_WR942N_V1_74HC_GPIO_BASE QCA956X_GPIO_COUNT +#define TL_WR942N_V1_74HC_GPIO_LED_LAN4 23 +#define TL_WR942N_V1_74HC_GPIO_LED_LAN3 24 +#define TL_WR942N_V1_74HC_GPIO_LED_LAN2 25 +#define TL_WR942N_V1_74HC_GPIO_LED_LAN1 26 +#define TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN 27 +#define TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER 28 +#define TL_WR942N_V1_74HC_GPIO_LED_WLAN 29 +#define TL_WR942N_V1_74HC_GPIO_HUB_RESET 30 /* from u-boot sources */ + +#define TL_WR942N_V1_SSR_BIT_0 0 +#define TL_WR942N_V1_SSR_BIT_1 1 +#define TL_WR942N_V1_SSR_BIT_2 2 +#define TL_WR942N_V1_SSR_BIT_3 3 +#define TL_WR942N_V1_SSR_BIT_4 4 +#define TL_WR942N_V1_SSR_BIT_5 5 +#define TL_WR942N_V1_SSR_BIT_6 6 +#define TL_WR942N_V1_SSR_BIT_7 7 + +#define TL_WR942N_V1_WMAC_CALDATA_OFFSET 0x1000 +#define TL_WR942N_V1_DEFAULT_MAC_ADDR 0x1fe40008 +#define TL_WR942N_V1_DEFAULT_MAC_SIZE 0x200 + +#define GPIO_IN_ENABLE0_UART_SIN_LSB 8 +#define GPIO_IN_ENABLE0_UART_SIN_MASK 0x0000ff00 + +static struct gpio_led tl_wr942n_v1_leds_gpio[] __initdata = { + { + .name = "tl-wr942n-v1:green:status", + .gpio = TL_WR942N_V1_GPIO_LED_STATUS, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:wlan", + .gpio = TL_WR942N_V1_74HC_GPIO_LED_WLAN, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:lan1", + .gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN1, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:lan2", + .gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN2, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:lan3", + .gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN3, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:lan4", + .gpio = TL_WR942N_V1_74HC_GPIO_LED_LAN4, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:wan", + .gpio = TL_WR942N_V1_74HC_GPIO_LED_WAN_GREEN, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:amber:wan", + .gpio = TL_WR942N_V1_74HC_GPIO_LED_WAN_AMBER, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:wps", + .gpio = TL_WR942N_V1_GPIO_LED_WPS, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:usb1", + .gpio = TL_WR942N_V1_GPIO_LED_USB1, + .active_low = 1, + }, { + .name = "tl-wr942n-v1:green:usb2", + .gpio = TL_WR942N_V1_GPIO_LED_USB2, + .active_low = 1, + }, +}; + +static struct gpio_keys_button tl_wr942n_v1_gpio_keys[] __initdata = { + { + .desc = "Reset button", + .type = EV_KEY, + .code = KEY_RESTART, + .debounce_interval = TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL, + .gpio = TL_WR942N_V1_GPIO_BTN_RESET, + .active_low = 1, + }, { + .desc = "RFKILL button", + .type = EV_KEY, + .code = KEY_RFKILL, + .debounce_interval = TL_WR942N_V1_KEYS_DEBOUNCE_INTERVAL, + .gpio = TL_WR942N_V1_GPIO_BTN_RFKILL, + .active_low = 1, + }, +}; + +static struct spi_gpio_platform_data tl_wr942n_v1_spi_data = { + .sck = TL_WR942N_V1_GPIO_SHIFT_SRCLK, + .miso = SPI_GPIO_NO_MISO, + .mosi = TL_WR942N_V1_GPIO_SHIFT_SER, + .num_chipselect = 1, +}; + +static u8 tl_wr942n_v1_ssr_initdata[] __initdata = { + BIT(TL_WR942N_V1_SSR_BIT_7) | + BIT(TL_WR942N_V1_SSR_BIT_6) | + BIT(TL_WR942N_V1_SSR_BIT_5) | + BIT(TL_WR942N_V1_SSR_BIT_4) | + BIT(TL_WR942N_V1_SSR_BIT_3) | + BIT(TL_WR942N_V1_SSR_BIT_2) | + BIT(TL_WR942N_V1_SSR_BIT_1) | + BIT(TL_WR942N_V1_SSR_BIT_0) +}; + +static struct gen_74x164_chip_platform_data tl_wr942n_v1_ssr_data = { + .base = TL_WR942N_V1_74HC_GPIO_BASE, + .num_registers = ARRAY_SIZE(tl_wr942n_v1_ssr_initdata), + .init_data = tl_wr942n_v1_ssr_initdata, +}; + +static struct platform_device tl_wr942n_v1_spi_device = { + .name = "spi_gpio", + .id = 1, + .dev = { + .platform_data = &tl_wr942n_v1_spi_data, + }, +}; + +static struct spi_board_info tl_wr942n_v1_spi_info[] = { + { + .bus_num = 1, + .chip_select = 0, + .max_speed_hz = 10000000, + .modalias = "74x164", + .platform_data = &tl_wr942n_v1_ssr_data, + .controller_data = (void *) TL_WR942N_V1_GPIO_SHIFT_RCLK, + }, +}; + +static void tl_wr942n_v1_get_mac(const char *name, char *mac) +{ + u8 *nvram = (u8 *) KSEG1ADDR(TL_WR942N_V1_DEFAULT_MAC_ADDR); + int err; + + err = ath79_nvram_parse_mac_addr(nvram, TL_WR942N_V1_DEFAULT_MAC_SIZE, + name, mac); + + if (err) + pr_err("no MAC address found for %s\n", name); +} + +static void __init tl_wr942n_v1_setup(void) +{ + u8 *art = (u8 *) KSEG1ADDR(0x1fff0000); + u8 tmpmac[ETH_ALEN]; + void __iomem *base; + u32 t; + + ath79_register_m25p80(NULL); + + spi_register_board_info(tl_wr942n_v1_spi_info, + ARRAY_SIZE(tl_wr942n_v1_spi_info)); + platform_device_register(&tl_wr942n_v1_spi_device); + + /* Check inherited UART RX GPIO definition */ + base = ioremap(AR71XX_GPIO_BASE, AR71XX_GPIO_SIZE); + + t = __raw_readl(base + QCA956X_GPIO_REG_IN_ENABLE0); + if (((t & GPIO_IN_ENABLE0_UART_SIN_MASK) + >> GPIO_IN_ENABLE0_UART_SIN_LSB) == TL_WR942N_V1_GPIO_LED_USB1) { + pr_warn("Active UART detected on USBLED's GPIOs!\n"); + + tl_wr942n_v1_leds_gpio[9].gpio = TL_WR942N_V1_GPIO_UART_TX; + tl_wr942n_v1_leds_gpio[10].gpio = TL_WR942N_V1_GPIO_UART_RX; + } + + ath79_register_leds_gpio(-1, ARRAY_SIZE(tl_wr942n_v1_leds_gpio), + tl_wr942n_v1_leds_gpio); + + ath79_register_gpio_keys_polled(-1, TL_WR942N_V1_KEYS_POLL_INTERVAL, + ARRAY_SIZE(tl_wr942n_v1_gpio_keys), + tl_wr942n_v1_gpio_keys); + + tl_wr942n_v1_get_mac("MAC:", tmpmac); + + /* swap PHYs */ + ath79_setup_qca956x_eth_cfg(QCA956X_ETH_CFG_SW_PHY_SWAP | + QCA956X_ETH_CFG_SW_PHY_ADDR_SWAP); + + ath79_register_mdio(0, 0x0); + ath79_register_mdio(1, 0x0); + + /* WAN port */ + ath79_init_mac(ath79_eth0_data.mac_addr, tmpmac, 1); + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII; + ath79_eth0_data.speed = SPEED_100; + ath79_eth0_data.duplex = DUPLEX_FULL; + + /* swaped PHYs */ + ath79_eth0_data.phy_mask = BIT(0); + ath79_register_eth(0); + + /* LAN ports */ + ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII; + ath79_init_mac(ath79_eth1_data.mac_addr, tmpmac, 0); + ath79_eth1_data.speed = SPEED_1000; + ath79_eth1_data.duplex = DUPLEX_FULL; + + /* swaped PHYs */ + ath79_switch_data.phy_poll_mask |= BIT(0); + ath79_switch_data.phy4_mii_en = 1; + ath79_register_eth(1); + + ath79_register_wmac(art + TL_WR942N_V1_WMAC_CALDATA_OFFSET, tmpmac); + + ath79_register_usb(); + + gpio_request_one(TL_WR942N_V1_74HC_GPIO_HUB_RESET, + GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED, + "USB power"); + + gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_OE, + GPIOF_OUT_INIT_LOW | GPIOF_EXPORT_DIR_FIXED, + "LED control"); + + gpio_request_one(TL_WR942N_V1_GPIO_SHIFT_SRCLR, + GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED, + "LED reset"); +} + +MIPS_MACHINE(ATH79_MACH_TL_WR942N_V1, "TL-WR942N-V1", "TP-LINK TL-WR942N v1", + tl_wr942n_v1_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index 0d05086a1c..46d250d47d 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -262,6 +262,7 @@ enum ath79_mach_type { ATH79_MACH_TL_WR941ND_V5, /* TP-LINK TL-WR941ND v5 */ ATH79_MACH_TL_WR941ND_V6, /* TP-LINK TL-WR941ND v6 */ ATH79_MACH_TL_WR940N_V4, /* TP-LINK TL-WR940N v4 */ + ATH79_MACH_TL_WR942N_V1, /* TP-LINK TL-WR942N v1 */ ATH79_MACH_TUBE2H, /* Alfa Network Tube2H */ ATH79_MACH_UBNT_AIRGW, /* Ubiquiti AirGateway */ ATH79_MACH_UBNT_AIRGWP, /* Ubiquiti AirGateway Pro */ diff --git a/target/linux/ar71xx/files/arch/mips/ath79/nvram.c b/target/linux/ar71xx/files/arch/mips/ath79/nvram.c index e55af5abe2..a1de55fb19 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/nvram.c +++ b/target/linux/ar71xx/files/arch/mips/ath79/nvram.c @@ -13,6 +13,7 @@ #include #include #include +#include #include "nvram.h" @@ -67,7 +68,11 @@ int ath79_nvram_parse_mac_addr(const char *nvram, unsigned nvram_len, t = sscanf(mac_str, "%02hhx:%02hhx:%02hhx:%02hhx:%02hhx:%02hhx", &mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]); - if (t != 6) { + if (t != ETH_ALEN) + t = sscanf(mac_str, "%02hhx-%02hhx-%02hhx-%02hhx-%02hhx-%02hhx", + &mac[0], &mac[1], &mac[2], &mac[3], &mac[4], &mac[5]); + + if (t != ETH_ALEN) { ret = -EINVAL; goto free; } diff --git a/target/linux/ar71xx/image/tp-link.mk b/target/linux/ar71xx/image/tp-link.mk index 5ac641bf36..d9c7982e8c 100644 --- a/target/linux/ar71xx/image/tp-link.mk +++ b/target/linux/ar71xx/image/tp-link.mk @@ -873,6 +873,21 @@ define Device/tl-wr941nd-v6-cn endef TARGET_DEVICES += tl-wr941nd-v2 tl-wr941nd-v3 tl-wr941nd-v4 tl-wr941nd-v5 tl-wr941nd-v6 tl-wr941nd-v6-cn tl-wr940n-v4 +define Device/tl-wr942n-v1 + DEVICE_TITLE := TP-LINK TL-WR942N v1 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport + BOARDNAME := TL-WR942N-V1 + TPLINK_BOARD_NAME := TLWR942NV1 + DEVICE_PROFILE := TLWR942 + IMAGE_SIZE := 14464k + KERNEL := kernel-bin | patch-cmdline | lzma | uImageArcher lzma + IMAGES := sysupgrade.bin factory.bin + IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade + IMAGE/factory.bin := append-rootfs | tplink-safeloader factory + MTDPARTS := spi0.0:128k(u-boot)ro,1344k(kernel),13120k(rootfs),64k(product-info)ro,64k(partition-table)ro,256k(oem-config)ro,1344k(oem-vars)ro,64k(ART)ro,14464k@0x20000(firmware) +endef +TARGET_DEVICES += tl-wr942n-v1 + define Device/tl-wr1041n-v2 $(Device/tplink-4mlzma) DEVICE_TITLE := TP-LINK TL-WR1041N v2 diff --git a/target/linux/ar71xx/mikrotik/config-default b/target/linux/ar71xx/mikrotik/config-default index 5c665801fe..748252ce48 100644 --- a/target/linux/ar71xx/mikrotik/config-default +++ b/target/linux/ar71xx/mikrotik/config-default @@ -172,6 +172,7 @@ CONFIG_ATH79_MACH_RBSXTLITE=y # CONFIG_ATH79_MACH_TL_WR940N_V4 is not set # CONFIG_ATH79_MACH_TL_WR941ND is not set # CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set +# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set # CONFIG_ATH79_MACH_TUBE2H is not set # CONFIG_ATH79_MACH_UBNT is not set # CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set diff --git a/target/linux/ar71xx/nand/config-default b/target/linux/ar71xx/nand/config-default index cc2b25c1af..7ae42fe8b9 100644 --- a/target/linux/ar71xx/nand/config-default +++ b/target/linux/ar71xx/nand/config-default @@ -160,6 +160,7 @@ CONFIG_ATH79_MACH_RAMBUTAN=y # CONFIG_ATH79_MACH_TL_WR940N_V4 is not set # CONFIG_ATH79_MACH_TL_WR941ND is not set # CONFIG_ATH79_MACH_TL_WR941ND_V6 is not set +# CONFIG_ATH79_MACH_TL_WR942N_V1 is not set # CONFIG_ATH79_MACH_TUBE2H is not set # CONFIG_ATH79_MACH_UBNT is not set # CONFIG_ATH79_MACH_UBNT_UNIFIAC is not set diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 9c9efc369c..31b374f523 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -553,6 +553,43 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system" }, + /** Firmware layout for the TL-WR942N V1 */ + { + .id = "TLWR942NV1", + .vendor = "", + .support_list = + "SupportList:\r\n" + "{product_name:TL-WR942N,product_ver:1.0.0,special_id:00000000}\r\n" + "{product_name:TL-WR942N,product_ver:1.0.0,special_id:52550000}\r\n", + .support_trail = '\x00', + .soft_ver = NULL, + + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"os-image", 0x20000, 0x150000}, + {"file-system", 0x170000, 0xcd0000}, + {"default-mac", 0xe40000, 0x00200}, + {"pin", 0xe40200, 0x00200}, + {"product-info", 0xe40400, 0x0fc00}, + {"partition-table", 0xe50000, 0x10000}, + {"soft-version", 0xe60000, 0x10000}, + {"support-list", 0xe70000, 0x10000}, + {"profile", 0xe80000, 0x10000}, + {"default-config", 0xe90000, 0x10000}, + {"user-config", 0xea0000, 0x40000}, + {"qos-db", 0xee0000, 0x40000}, + {"certificate", 0xf20000, 0x10000}, + {"usb-config", 0xfb0000, 0x10000}, + {"log", 0xfc0000, 0x20000}, + {"radio-bk", 0xfe0000, 0x10000}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system", + }, + /** Firmware layout for the RE450 */ { .id = "RE450",