From: David Bauer Date: Tue, 24 Apr 2018 17:52:13 +0000 (+0200) Subject: ar71xx: add support for Fritz!Box 4020 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=b6a4c674684585902ee07a4ba7c89d988d633650;p=openwrt%2Fstaging%2Faparcar.git ar71xx: add support for Fritz!Box 4020 This commit adds support for the AVM Fritz!Box 4020 WiFi-router. SoC: Qualcomm Atheros QCA9561 (Dragonfly) 750MHz RAM: Winbond W971GG6KB-25 FLASH: Macronix MX25L12835F WiFi: QCA9561 b/g/n 3x3 450Mbit/s USB: 1x USB 2.0 IN: WPS button, WiFi button OUT: Power LED green, Internet LED green, WLAN LED green, LAN LED green, INFO LED green, INFO LED red UART: Header Next to Black metal shield Pinout is 3.3V - RX - TX - GND (Square Pad is 3.3V) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (LAN + WAN) - WiFi (correct MAC) - Installation via EVA bootloader - OpenWRT sysupgrade - Buttons - LEDs Not working: - USB port Installation via EVA: In the first seconds after Power is connected, the bootloader will listen for FTP connections on 169.254.157.1 (Might also be 192.168.178.1). Firmware can be uploaded like following: ftp> quote USER adam2 ftp> quote PASS adam2 ftp> binary ftp> debug ftp> passive ftp> quote MEDIA FLSH ftp> put openwrt-sysupgrade.bin mtd1 Note that this procedure might take up to two minutes. After transfer is complete you need to powercycle the device to boot OpenWRT. Signed-off-by: David Bauer --- diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds b/target/linux/ar71xx/base-files/etc/board.d/01_leds index 906c4b715f..52f1ac3ecf 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/01_leds +++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds @@ -372,6 +372,12 @@ epg5000) ucidef_set_led_wlan "wlan2g" "WLAN 2.4 GHz" "$board:blue:wlan-2g" "phy1tpt" ucidef_set_led_wlan "wlan5g" "WLAN 5 GHz" "$board:blue:wlan-5g" "phy0tpt" ;; +fritz4020) + ucidef_set_led_default "power" "Power" "$board:green:power" "1" + ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth1" + ucidef_set_led_netdev "wan" "WAN" "$board:green:wan" "eth0" + ucidef_set_led_wlan "wlan" "WLAN" "$board:green:wlan" "phy0tpt" + ;; gl-ar300m) ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt" ;; diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network b/target/linux/ar71xx/base-files/etc/board.d/02_network index cbbcf53946..5898261b3d 100755 --- a/target/linux/ar71xx/base-files/etc/board.d/02_network +++ b/target/linux/ar71xx/base-files/etc/board.d/02_network @@ -243,6 +243,7 @@ ar71xx_setup_interfaces() ;; archer-c58-v1|\ archer-c59-v1|\ + fritz4020|\ rb-450g) ucidef_set_interfaces_lan_wan "eth1.1" "eth0" ucidef_add_switch "switch0" \ diff --git a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom index 41ab43f7cb..6eb946468d 100644 --- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom +++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/10-ath9k-eeprom @@ -75,6 +75,9 @@ case "$FIRMWARE" in ath9k_eeprom_extract "art" 4096 2048 ath9k_patch_firmware_mac $(macaddr_add $(mtd_get_mac_binary art 0) +1) ;; + fritz4020) + ath9k_eeprom_extract_reverse "urlader" 5441 1088 + ;; mr18) . /lib/upgrade/nand.sh diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh b/target/linux/ar71xx/base-files/lib/ar71xx.sh index 95314a2881..42bd80d9ad 100755 --- a/target/linux/ar71xx/base-files/lib/ar71xx.sh +++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh @@ -709,6 +709,9 @@ ar71xx_board_detect() { *"eTactica EG-200") name="rme-eg200" ;; + *"FRITZ!Box 4020") + name="fritz4020" + ;; *"FRITZ!WLAN Repeater 300E") name="fritz300e" ;; diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh index 702d97a8ed..284582fa2b 100755 --- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh @@ -686,6 +686,7 @@ platform_check_image() { ;; # these boards use metadata images fritz300e|\ + fritz4020|\ rb-750-r2|\ rb-750p-pbr2|\ rb-750up-r2|\ diff --git a/target/linux/ar71xx/config-4.9 b/target/linux/ar71xx/config-4.9 index 5cea1b7bde..35efd1710b 100644 --- a/target/linux/ar71xx/config-4.9 +++ b/target/linux/ar71xx/config-4.9 @@ -115,6 +115,7 @@ CONFIG_ATH79=y # CONFIG_ATH79_MACH_EW_DORIN is not set # CONFIG_ATH79_MACH_F9K1115V2 is not set # CONFIG_ATH79_MACH_FRITZ300E is not set +# CONFIG_ATH79_MACH_FRITZ4020 is not set # CONFIG_ATH79_MACH_GL_AR150 is not set # CONFIG_ATH79_MACH_GL_AR300 is not set # CONFIG_ATH79_MACH_GL_AR300M is not set diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt index 4a032f6021..40d33b53fa 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt +++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt @@ -2347,3 +2347,12 @@ config ATH79_MACH_FRITZ300E select ATH79_DEV_GPIO_BUTTONS select ATH79_DEV_LEDS_GPIO select ATH79_DEV_M25P80 + +config ATH79_MACH_FRITZ4020 + bool "AVM FRITZ!Box 4020 support" + select SOC_QCA956X + select ATH79_DEV_ETH + select ATH79_DEV_GPIO_BUTTONS + select ATH79_DEV_LEDS_GPIO + select ATH79_DEV_USB + select ATH79_DEV_M25P80 diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile b/target/linux/ar71xx/files/arch/mips/ath79/Makefile index e606e2c3df..2124ab70c9 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile +++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile @@ -125,6 +125,7 @@ obj-$(CONFIG_ATH79_MACH_EW_BALIN) += mach-ew-balin.o obj-$(CONFIG_ATH79_MACH_EW_DORIN) += mach-ew-dorin.o obj-$(CONFIG_ATH79_MACH_F9K1115V2) += mach-f9k1115v2.o obj-$(CONFIG_ATH79_MACH_FRITZ300E) += mach-fritz300e.o +obj-$(CONFIG_ATH79_MACH_FRITZ4020) += mach-fritz4020.o obj-$(CONFIG_ATH79_MACH_GL_AR150) += mach-gl-ar150.o obj-$(CONFIG_ATH79_MACH_GL_AR300) += mach-gl-ar300.o obj-$(CONFIG_ATH79_MACH_GL_AR300M) += mach-gl-ar300m.o diff --git a/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.c b/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.c index 9e72c41a42..b46bab7886 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.c +++ b/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.c @@ -1175,6 +1175,15 @@ void __init ath79_parse_ascii_mac(char *mac_str, u8 *mac) } } +void __init ath79_extract_mac_reverse(u8 *ptr, u8 *out) +{ + int i; + + for (i = 0; i < ETH_ALEN; i++) { + out[i] = ptr[ETH_ALEN-i-1]; + } +} + static void __init ath79_set_mac_base_ascii(char *str) { u8 mac[ETH_ALEN]; diff --git a/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.h b/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.h index fb9e4f63c6..4d78260fbe 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/dev-eth.h @@ -18,6 +18,7 @@ struct platform_device; extern unsigned char ath79_mac_base[] __initdata; void ath79_parse_ascii_mac(char *mac_str, u8 *mac); +void ath79_extract_mac_reverse(u8 *ptr, u8 *out); void ath79_init_mac(unsigned char *dst, const unsigned char *src, int offset); void ath79_init_local_mac(unsigned char *dst, const unsigned char *src); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-fritz4020.c b/target/linux/ar71xx/files/arch/mips/ath79/mach-fritz4020.c new file mode 100644 index 0000000000..ed7f9a8b3e --- /dev/null +++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-fritz4020.c @@ -0,0 +1,242 @@ +/* + * AVM FRITZ!Box 4020 board support + * + * Copyright (C) 2018 David Bauer + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License version 2 as published + * by the Free Software Foundation. + */ + +#include +#include +#include +#include +#include + +#include +#include +#include +#include +#include + +#include +#include + +#include "common.h" +#include "dev-eth.h" +#include "dev-gpio-buttons.h" +#include "dev-leds-gpio.h" +#include "dev-m25p80.h" +#include "dev-spi.h" +#include "dev-usb.h" +#include "dev-wmac.h" +#include "machtypes.h" + + +#define FRITZ4020_GPIO_SHIFT_SER 19 /* DS, Data Serial Input */ +#define FRITZ4020_GPIO_SHIFT_SRCLK 20 /* SHCP, Shift Reg Clock Input */ + +#define FRITZ4020_SSR_BIT_0 0 +#define FRITZ4020_SSR_BIT_1 1 +#define FRITZ4020_SSR_BIT_2 2 +#define FRITZ4020_SSR_BIT_3 3 +#define FRITZ4020_SSR_BIT_4 4 +#define FRITZ4020_SSR_BIT_5 5 +#define FRITZ4020_SSR_BIT_6 6 +#define FRITZ4020_SSR_BIT_7 7 + +#define FRITZ4020_74HC_GPIO_BASE 32 +#define FRITZ4020_74HC_GPIO_LED_LAN (FRITZ4020_74HC_GPIO_BASE + 0) +#define FRITZ4020_74HC_GPIO_LED_INFO_RED (FRITZ4020_74HC_GPIO_BASE + 1) +#define FRITZ4020_74HC_GPIO_LED_POWER (FRITZ4020_74HC_GPIO_BASE + 2) +#define FRITZ4020_74HC_GPIO_LED_WLAN (FRITZ4020_74HC_GPIO_BASE + 3) +#define FRITZ4020_74HC_GPIO_LED_WAN (FRITZ4020_74HC_GPIO_BASE + 4) +#define FRITZ4020_74HC_GPIO_USB_RST (FRITZ4020_74HC_GPIO_BASE + 5) +#define FRITZ4020_74HC_GPIO_LED_INFO (FRITZ4020_74HC_GPIO_BASE + 6) + + +#define FRITZ4020_GPIO_BTN_WPS 2 +#define FRITZ4020_GPIO_BTN_WLAN 21 +#define FRITZ4020_KEYS_POLL_INTERVAL 20 /* msecs */ +#define FRITZ4020_KEYS_DEBOUNCE_INTERVAL (3 * FRITZ4020_KEYS_POLL_INTERVAL) + +#define FRTIZ4020_OFFSET_URLADER_WIFI_MAC_REVERSE 0x1979 + + +static struct spi_gpio_platform_data fritz4020_spi_data = { + .sck = FRITZ4020_GPIO_SHIFT_SRCLK, + .miso = SPI_GPIO_NO_MISO, + .mosi = FRITZ4020_GPIO_SHIFT_SER, + .num_chipselect = 1, +}; + +static u8 fritz4020_ssr_initdata[] = { + BIT(FRITZ4020_SSR_BIT_7) | + BIT(FRITZ4020_SSR_BIT_6) | + BIT(FRITZ4020_SSR_BIT_5) | + BIT(FRITZ4020_SSR_BIT_4) | + BIT(FRITZ4020_SSR_BIT_3) | + BIT(FRITZ4020_SSR_BIT_2) | + BIT(FRITZ4020_SSR_BIT_1) +}; + +static struct gen_74x164_chip_platform_data fritz4020_ssr_data = { + .base = FRITZ4020_74HC_GPIO_BASE, + .num_registers = ARRAY_SIZE(fritz4020_ssr_initdata), + .init_data = fritz4020_ssr_initdata, +}; + +static struct platform_device fritz4020_spi_device = { + .name = "spi_gpio", + .id = 1, + .dev = { + .platform_data = &fritz4020_spi_data, + }, +}; + +static struct spi_board_info fritz4020_spi_info[] = { + { + .bus_num = 1, + .chip_select = 0, + .max_speed_hz = 10000000, + .modalias = "74x164", + .platform_data = &fritz4020_ssr_data, + .controller_data = (void *) 0x0, + }, +}; + +static struct mtd_partition fritz4020_flash_partitions[] = { + { + .name = "urlader", + .offset = 0, + .size = 0x0020000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "firmware", + .offset = 0x0020000, + .size = 0x0EE0000, + }, { + .name = "tffs (1)", + .offset = 0x0f00000, + .size = 0x0080000, + .mask_flags = MTD_WRITEABLE, + }, { + .name = "tffs (2)", + .offset = 0x0f80000, + .size = 0x0080000, + .mask_flags = MTD_WRITEABLE, + } +}; + +static struct flash_platform_data fritz4020_flash_data = { + .parts = fritz4020_flash_partitions, + .nr_parts = ARRAY_SIZE(fritz4020_flash_partitions), +}; + +static struct gpio_led fritz4020_leds_gpio[] __initdata = { + { + .name = "fritz4020:green:lan", + .gpio = FRITZ4020_74HC_GPIO_LED_LAN, + .active_low = 1, + }, { + .name = "fritz4020:green:info", + .gpio = FRITZ4020_74HC_GPIO_LED_INFO, + .active_low = 1, + }, { + .name = "fritz4020:red:info", + .gpio = FRITZ4020_74HC_GPIO_LED_INFO_RED, + .active_low = 1, + }, { + .name = "fritz4020:green:power", + .gpio = FRITZ4020_74HC_GPIO_LED_POWER, + .active_low = 1, + }, { + .name = "fritz4020:green:wlan", + .gpio = FRITZ4020_74HC_GPIO_LED_WLAN, + .active_low = 1, + }, { + .name = "fritz4020:green:wan", + .gpio = FRITZ4020_74HC_GPIO_LED_WAN, + .active_low = 1, + }, +}; + +static struct gpio_keys_button fritz4020_gpio_keys[] __initdata = { + { + .desc = "RFKILL button", + .type = EV_KEY, + .code = KEY_RFKILL, + .debounce_interval = FRITZ4020_KEYS_DEBOUNCE_INTERVAL, + .gpio = FRITZ4020_GPIO_BTN_WLAN, + .active_low = 0, + }, + { + .desc = "WPS button", + .type = EV_KEY, + .code = KEY_WPS_BUTTON, + .debounce_interval = FRITZ4020_KEYS_DEBOUNCE_INTERVAL, + .gpio = FRITZ4020_GPIO_BTN_WPS, + .active_low = 0, + }, +}; + +static void __init fritz4020_setup(void) { + u8 *urlader = (u8 *) KSEG1ADDR(0x1f000000); + u8 wifi_mac[ETH_ALEN]; + + ath79_register_m25p80(&fritz4020_flash_data); + + /* Initialize ethernet */ + ath79_extract_mac_reverse(urlader + FRTIZ4020_OFFSET_URLADER_WIFI_MAC_REVERSE, wifi_mac); + ath79_setup_qca956x_eth_cfg(QCA956X_ETH_CFG_SW_PHY_SWAP | + QCA956X_ETH_CFG_SW_PHY_ADDR_SWAP); + + ath79_register_mdio(0, 0x0); + ath79_register_mdio(1, 0x0); + ath79_init_mac(ath79_eth0_data.mac_addr, wifi_mac, -1); + ath79_init_mac(ath79_eth1_data.mac_addr, wifi_mac, -2); + + /* WAN port */ + ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_MII; + ath79_eth0_data.speed = SPEED_100; + ath79_eth0_data.duplex = DUPLEX_FULL; + ath79_eth0_data.phy_mask = BIT(0); + ath79_register_eth(0); + + /* LAN ports */ + ath79_eth1_data.phy_if_mode = PHY_INTERFACE_MODE_GMII; + ath79_eth1_data.speed = SPEED_1000; + ath79_eth1_data.duplex = DUPLEX_FULL; + ath79_switch_data.phy_poll_mask |= BIT(0); + ath79_switch_data.phy4_mii_en = 1; + ath79_register_eth(1); + + /* Initialize 2.4GHz WiFi */ + ath79_register_wmac_simple(); + + /* Activate USB Power */ + gpio_request_one(FRITZ4020_74HC_GPIO_USB_RST, + GPIOF_OUT_INIT_HIGH | GPIOF_EXPORT_DIR_FIXED, + "USB power"); + + /* Initialize USB port */ + ath79_register_usb(); + + /* Register LED shift-register */ + spi_register_board_info(fritz4020_spi_info, + ARRAY_SIZE(fritz4020_spi_info)); + platform_device_register(&fritz4020_spi_device); + + /* Register GPIO buttons */ + ath79_register_gpio_keys_polled(-1, FRITZ4020_KEYS_POLL_INTERVAL, + ARRAY_SIZE(fritz4020_gpio_keys), + fritz4020_gpio_keys); + + /* Register LEDs */ + ath79_register_leds_gpio(-1, ARRAY_SIZE(fritz4020_leds_gpio), + fritz4020_leds_gpio); +} + +MIPS_MACHINE(ATH79_MACH_FRITZ4020, "FRITZ4020", + "AVM FRITZ!Box 4020", fritz4020_setup); diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h index b61ed7abcd..3d5bcfbab4 100644 --- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h +++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h @@ -120,6 +120,7 @@ enum ath79_mach_type { ATH79_MACH_EW_DORIN_ROUTER, /* embedded wireless Dorin Router Platform */ ATH79_MACH_F9K1115V2, /* Belkin AC1750DB */ ATH79_MACH_FRITZ300E, /* AVM FRITZ!WLAN Repeater 300E */ + ATH79_MACH_FRITZ4020, /* AVM FRITZ!Box 4020 */ ATH79_MACH_GL_AR150, /* GL-AR150 support */ ATH79_MACH_GL_AR300, /* GL-AR300 */ ATH79_MACH_GL_AR300M, /* GL-AR300M */ diff --git a/target/linux/ar71xx/generic/config-default b/target/linux/ar71xx/generic/config-default index 6475d2281a..3f93d6e61e 100644 --- a/target/linux/ar71xx/generic/config-default +++ b/target/linux/ar71xx/generic/config-default @@ -88,6 +88,7 @@ CONFIG_ATH79_MACH_EW_BALIN=y CONFIG_ATH79_MACH_EW_DORIN=y CONFIG_ATH79_MACH_F9K1115V2=y CONFIG_ATH79_MACH_FRITZ300E=y +CONFIG_ATH79_MACH_FRITZ4020=y CONFIG_ATH79_MACH_GL_AR150=y CONFIG_ATH79_MACH_GL_AR300=y CONFIG_ATH79_MACH_GL_AR300M=y diff --git a/target/linux/ar71xx/image/generic.mk b/target/linux/ar71xx/image/generic.mk index 0d3aedb460..a0f6326145 100644 --- a/target/linux/ar71xx/image/generic.mk +++ b/target/linux/ar71xx/image/generic.mk @@ -1282,16 +1282,31 @@ define Device/zbt-we1526 endef TARGET_DEVICES += zbt-we1526 -define Device/fritz300e - DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E - DEVICE_PACKAGES := fritz-tffs rssileds -swconfig -uboot-envtools - BOARDNAME := FRITZ300E - SUPPORTED_DEVICES := fritz300e - IMAGE_SIZE := 15232k +define Device/AVM + DEVICE_PACKAGES := fritz-tffs -uboot-envtools KERNEL := kernel-bin | patch-cmdline | lzma | eva-image KERNEL_INITRAMFS := $$(KERNEL) IMAGE/sysupgrade.bin := append-kernel | pad-to 64k | \ append-squashfs-fakeroot-be | pad-to 256 | \ append-rootfs | pad-rootfs | append-metadata | check-size $$$$(IMAGE_SIZE) endef + +define Device/fritz300e + $(call Device/AVM) + DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E + DEVICE_PACKAGES := rssileds -swconfig + BOARDNAME := FRITZ300E + SUPPORTED_DEVICES := fritz300e + IMAGE_SIZE := 15232k +endef TARGET_DEVICES += fritz300e + +define Device/fritz4020 + $(call Device/AVM) + DEVICE_TITLE := AVM FRITZ!Box 4020 + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage + BOARDNAME := FRITZ4020 + SUPPORTED_DEVICES := fritz4020 + IMAGE_SIZE := 15232k +endef +TARGET_DEVICES += fritz4020