From: Petr Štetiar Date: Wed, 4 Nov 2020 10:37:42 +0000 (+0100) Subject: rtl838x: add support for D-Link DGS-1210-28 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=b5bd945733a7ed235777c2ceaa0ff27dc779630f;p=openwrt%2Fstaging%2Frobimarko.git rtl838x: add support for D-Link DGS-1210-28 Hardware specification ---------------------- * RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz * 128MB DRAM * 32MB NOR Flash (MX25L25635E) * 24 x 10/100/1000BASE-T ports - Internal PHY with 8 ports (RTL8218B) - Two external PHYs with 8 ports each (RTL8218B) * 4 x Gigabit RJ45/SFP Combo ports - External PHY with 4 SFP ports (RTL8214FC) * Power LED * Reset button on front panel * UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6 UART pinout ----------- [oooo]J3 [o]ooo|J6 | ^ ||`------ GND | | |`------- RX | | `-------- TX | `---------- Vcc (3V3) | `------------------ J3 is power input connector nearby J6 UART Boot initramfs image from U-Boot -------------------------------- 1. Press Escape key during `Hit Esc key to stop autoboot` prompt 2. Press CTRL+C keys to get into real U-Boot prompt 3. Init network with `rtk network on` command 4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command 5. Boot the image with `bootm` command To install, upload the sysupgrade image to the OEM webpage or sysupgrade from the system running from initramfs image. It has been developed and tested on device with F1 revision. Signed-off-by: Petr Štetiar --- diff --git a/target/linux/rtl838x/dts/rtl8382_d-link_dgs-1210-28.dts b/target/linux/rtl838x/dts/rtl8382_d-link_dgs-1210-28.dts new file mode 100644 index 0000000000..f154ca963d --- /dev/null +++ b/target/linux/rtl838x/dts/rtl8382_d-link_dgs-1210-28.dts @@ -0,0 +1,339 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "rtl8382_d-link_dgs-1210.dtsi" + +/ { + compatible = "d-link,dgs-1210-28", "realtek,rtl838x-soc"; + model = "D-Link DGS-1210-28"; +}; + +ðernet0 { + mdio: mdio-bus { + compatible = "realtek,rtl838x-mdio"; + regmap = <ðernet0>; + #address-cells = <1>; + #size-cells = <0>; + + /* External phy RTL8218B */ + phy0: ethernet-phy@0 { + reg = <0>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy1: ethernet-phy@1 { + reg = <1>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy2: ethernet-phy@2 { + reg = <2>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy3: ethernet-phy@3 { + reg = <3>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy4: ethernet-phy@4 { + reg = <4>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy5: ethernet-phy@5 { + reg = <5>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy6: ethernet-phy@6 { + reg = <6>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy7: ethernet-phy@7 { + reg = <7>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + + /* Internal phy RTL8218B */ + phy8: ethernet-phy@8 { + reg = <8>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + phy9: ethernet-phy@9 { + reg = <9>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + phy10: ethernet-phy@10 { + reg = <10>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + phy11: ethernet-phy@11 { + reg = <11>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + phy12: ethernet-phy@12 { + reg = <12>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + phy13: ethernet-phy@13 { + reg = <13>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + phy14: ethernet-phy@14 { + reg = <14>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + phy15: ethernet-phy@15 { + reg = <15>; + compatible = "ethernet-phy-ieee802.3-c22"; + phy-is-integrated; + }; + + /* External phy RTL8218B */ + phy16: ethernet-phy@16 { + reg = <16>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy17: ethernet-phy@17 { + reg = <17>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy18: ethernet-phy@18 { + reg = <18>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy19: ethernet-phy@19 { + reg = <19>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy20: ethernet-phy@20 { + reg = <20>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy21: ethernet-phy@21 { + reg = <21>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy22: ethernet-phy@22 { + reg = <22>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + phy23: ethernet-phy@23 { + reg = <23>; + compatible = "ethernet-phy-ieee802.3-c22"; + }; + + /* External phy: RTL8214FC */ + phy24: ethernet-phy@24 { + compatible = "ethernet-phy-ieee802.3-c22"; + sfp; + media = "fibre"; + reg = <24>; + }; + phy25: ethernet-phy@25 { + compatible = "ethernet-phy-ieee802.3-c22"; + sfp; + media = "fibre"; + reg = <25>; + }; + phy26: ethernet-phy@26 { + compatible = "ethernet-phy-ieee802.3-c22"; + sfp; + media = "fibre"; + reg = <26>; + }; + phy27: ethernet-phy@27 { + compatible = "ethernet-phy-ieee802.3-c22"; + sfp; + media = "fibre"; + reg = <27>; + }; + }; +}; + +&switch0 { + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + phy-handle = <&phy0>; + phy-mode = "qsgmii"; + }; + port@1 { + reg = <1>; + label = "lan2"; + phy-handle = <&phy1>; + phy-mode = "qsgmii"; + }; + port@2 { + reg = <2>; + label = "lan3"; + phy-handle = <&phy2>; + phy-mode = "qsgmii"; + }; + port@3 { + reg = <3>; + label = "lan4"; + phy-handle = <&phy3>; + phy-mode = "qsgmii"; + }; + port@4 { + reg = <4>; + label = "lan5"; + phy-handle = <&phy4>; + phy-mode = "qsgmii"; + }; + port@5 { + reg = <5>; + label = "lan6"; + phy-handle = <&phy5>; + phy-mode = "qsgmii"; + }; + port@6 { + reg = <6>; + label = "lan7"; + phy-handle = <&phy6>; + phy-mode = "qsgmii"; + }; + port@7 { + reg = <7>; + label = "lan8"; + phy-handle = <&phy7>; + phy-mode = "qsgmii"; + }; + port@8 { + reg = <8>; + label = "lan9"; + phy-handle = <&phy8>; + phy-mode = "internal"; + }; + port@9 { + reg = <9>; + label = "lan10"; + phy-handle = <&phy9>; + phy-mode = "internal"; + }; + port@10 { + reg = <10>; + label = "lan11"; + phy-handle = <&phy10>; + phy-mode = "internal"; + }; + port@11 { + reg = <11>; + label = "lan12"; + phy-handle = <&phy11>; + phy-mode = "internal"; + }; + port@12 { + reg = <12>; + label = "lan13"; + phy-handle = <&phy12>; + phy-mode = "internal"; + }; + port@13 { + reg = <13>; + label = "lan14"; + phy-handle = <&phy13>; + phy-mode = "internal"; + }; + port@14 { + reg = <14>; + label = "lan15"; + phy-handle = <&phy14>; + phy-mode = "internal"; + }; + port@15 { + reg = <15>; + label = "lan16"; + phy-handle = <&phy15>; + phy-mode = "internal"; + }; + port@16 { + reg = <16>; + label = "lan17"; + phy-handle = <&phy16>; + phy-mode = "qsgmii"; + }; + port@17 { + reg = <17>; + label = "lan18"; + phy-handle = <&phy17>; + phy-mode = "qsgmii"; + }; + port@18 { + reg = <18>; + label = "lan19"; + phy-handle = <&phy18>; + phy-mode = "qsgmii"; + }; + port@19 { + reg = <19>; + label = "lan20"; + phy-handle = <&phy19>; + phy-mode = "qsgmii"; + }; + port@20 { + reg = <20>; + label = "lan21"; + phy-handle = <&phy20>; + phy-mode = "qsgmii"; + }; + port@21 { + reg = <21>; + label = "lan22"; + phy-handle = <&phy21>; + phy-mode = "qsgmii"; + }; + port@22 { + reg = <22>; + label = "lan23"; + phy-handle = <&phy22>; + phy-mode = "qsgmii"; + }; + port@23 { + reg = <23>; + label = "lan24"; + phy-handle = <&phy23>; + phy-mode = "qsgmii"; + }; + + port@24 { + reg = <24>; + label = "lan25"; + phy-handle = <&phy24>; + phy-mode = "qsgmii"; + }; + port@25 { + reg = <25>; + label = "lan26"; + phy-handle = <&phy25>; + phy-mode = "qsgmii"; + }; + port@26 { + reg = <26>; + label = "lan27"; + phy-handle = <&phy26>; + phy-mode = "qsgmii"; + }; + port@27 { + reg = <27>; + label = "lan28"; + phy-handle = <&phy27>; + phy-mode = "qsgmii"; + }; + port@28 { + ethernet = <ðernet0>; + reg = <28>; + phy-mode = "internal"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; +}; diff --git a/target/linux/rtl838x/image/Makefile b/target/linux/rtl838x/image/Makefile index cd384c5345..51acd41c76 100644 --- a/target/linux/rtl838x/image/Makefile +++ b/target/linux/rtl838x/image/Makefile @@ -61,4 +61,9 @@ define Device/d-link_dgs-1210-16 endef TARGET_DEVICES += d-link_dgs-1210-16 +define Device/d-link_dgs-1210-28 + $(Device/d-link_dgs-1210) + DEVICE_MODEL := DGS-1210-28 +endef +TARGET_DEVICES += d-link_dgs-1210-28 $(eval $(call BuildImage))