From: Peter Adkins Date: Wed, 9 Jun 2021 20:35:46 +0000 (+0100) Subject: ipq40xx: add support for Linksys WHW01 v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=b4184c666c13fdf08ecd3abf340538d593e9084c;p=openwrt%2Fstaging%2Fblocktrron.git ipq40xx: add support for Linksys WHW01 v1 This patch adds support for Linksys WHW01 v1 ("Velop") [FCC ID Q87-03331]. Specification ------------- SOC: Qualcomm IPQ4018 WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n WiFi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Ethernet: Qualcomm QCA8072 (2-port) SPI Flash 1: Mactronix MX25L1605D (2MB) SPI Flash 2: Winbond W25M02GV (256MB) DRAM: Nanya NT5CC128M16IP-DI (256MB) LED Controller: NXP PCA963x (I2C) Buttons: Single reset button (GPIO). Notes ----- There does not appear to be a way to trigger TFTP recovery without entering U-Boot. The device must be opened to access the serial console in order to first flash OpenWrt onto a device from factory. The device has automatic recovery backed by a second set of partitions on the larger of the two SPI flash ICs. Both the primary and secondary must be flashed to prevent accidental rollback to "factory" after 3 failed boot attempts. Serial console -------------- A serial console is available on the following pins of the populated J2 connector on the device mainboard (115200 8n1). (<-- Top of PCB / Device) J2 [o o o o o o] | | | | | `-- GND | `---- TX `--------- RX Installation instructions ------------------------- 1. Setup TFTP server with server IP set to 192.168.1.236. 2. Copy compiled `...squashfs-factory.bin` to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Revert to "factory" ------------------- 1. Download latest firmware update from vendor support site. 2. Copy extracted `.img` file to `nodes-jr.img` in tftp root. 3. Connect to console using pinout detailed in the serial console section. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash first partition device via `run flashimg`. 6. Once complete, reset device and allow to power up completely. 7. Once comfortable with device upgrade reboot and drop back into U-Boot. 8. Flash the second partition (recovery) via `run flashimg2`. Link: https://github.com/openwrt/openwrt/pull/3682 Signed-off-by: Peter Adkins (calibration from nvmem, updated to 5.10+5.15) Signed-off-by: Christian Lamparter --- diff --git a/package/boot/uboot-envtools/files/ipq40xx b/package/boot/uboot-envtools/files/ipq40xx index 9a71a622f7..1937f9d1ce 100644 --- a/package/boot/uboot-envtools/files/ipq40xx +++ b/package/boot/uboot-envtools/files/ipq40xx @@ -60,6 +60,9 @@ linksys,ea8300|\ linksys,mr8300) ubootenv_add_uci_config "/dev/mtd7" "0x0" "0x40000" "0x20000" ;; +linksys,whw01-v1) + ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x40000" "0x10000" + ;; zyxel,nbg6617) ubootenv_add_uci_config "/dev/mtd6" "0x0" "0x10000" "0x10000" ;; diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index f3dfd656c3..39450a5af7 100644 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -82,7 +82,8 @@ ipq40xx_setup_interfaces() ucidef_add_switch "switch0" \ "0u@eth0" "1:lan:4" "2:lan:3" "3:lan:2" "4:lan:1" ;; - avm,fritzrepeater-3000) + avm,fritzrepeater-3000|\ + linksys,whw01-v1) ucidef_add_switch "switch0" \ "0u@eth0" "4:lan:1" "5:lan:2" ;; diff --git a/target/linux/ipq40xx/base-files/etc/init.d/bootcount b/target/linux/ipq40xx/base-files/etc/init.d/bootcount index 9abfbddc43..367ccfcd0c 100755 --- a/target/linux/ipq40xx/base-files/etc/init.d/bootcount +++ b/target/linux/ipq40xx/base-files/etc/init.d/bootcount @@ -10,7 +10,8 @@ boot() { ;; linksys,ea6350v3|\ linksys,ea8300|\ - linksys,mr8300) + linksys,mr8300|\ + linksys,whw01-v1) mtd resetbc s_env || true ;; netgear,wac510) diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index cded9e3a7f..8a6702df4e 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -161,7 +161,8 @@ platform_do_upgrade() { ;; linksys,ea6350v3 |\ linksys,ea8300 |\ - linksys,mr8300) + linksys,mr8300 |\ + linksys,whw01-v1) platform_do_upgrade_linksys "$1" ;; meraki,mr33) diff --git a/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-whw01-v1.dts b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-whw01-v1.dts new file mode 100644 index 0000000000..6f244132ea --- /dev/null +++ b/target/linux/ipq40xx/files/arch/arm/boot/dts/qcom-ipq4018-whw01-v1.dts @@ -0,0 +1,330 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Linksys WHW01 v1"; + compatible = "linksys,whw01-v1"; + + aliases { + serial0 = &blsp1_uart1; + led-boot = &led_system_blue; + led-running = &led_system_blue; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs-append = " root=/dev/ubiblock0_0"; + }; + + soc { + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + ess_tcsr@1953000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; +}; + +&blsp_dma { + status = "okay"; +}; + +&blsp1_i2c3 { + status = "okay"; + pinctrl-0 = <&i2c_0_pins>; + pinctrl-1 = <&i2c_0_pins>; + pinctrl-names = "i2c_active", "i2c_sleep"; + + leds@62 { + compatible = "nxp,pca9633"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x62>; + + /* RGB? */ + led@0 { + reg = <0>; + color = ; + function = LED_FUNCTION_POWER; + }; + + led@1 { + reg = <1>; + color = ; + function = LED_FUNCTION_POWER; + }; + + led_system_blue: led@2 { + reg = <2>; + color = ; + function = LED_FUNCTION_POWER; + linux,default-trigger = "default-on"; + }; + }; +}; + +&blsp1_spi1 { + status = "okay"; + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, <&tlmm 4 GPIO_ACTIVE_HIGH>; + + nor@0 { + reg = <0>; + compatible = "jedec,spi-nor"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "0:SBL1"; + reg = <0x0 0x40000>; + read-only; + }; + + partition@40000 { + label = "0:MIBIB"; + reg = <0x40000 0x20000>; + read-only; + }; + + partition@60000 { + label = "0:QSEE"; + reg = <0x60000 0x60000>; + read-only; + }; + + partition@c0000 { + label = "0:CDT"; + reg = <0xc0000 0x10000>; + read-only; + }; + + partition@d0000 { + label = "APPSBL"; + reg = <0xd0000 0xa0000>; + read-only; + }; + + partition@170000 { + label = "0:ART"; + reg = <0x170000 0x10000>; + read-only; + + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + precal_art_1000: precal@1000 { + reg = <0x1000 0x2f20>; + }; + + precal_art_5000: precal@5000 { + reg = <0x5000 0x2f20>; + }; + }; + + partition@180000 { + label = "u_env"; + reg = <0x180000 0x40000>; + }; + + partition@1c0000 { + label = "s_env"; + reg = <0x1c0000 0x20000>; + }; + + partition@1e0000 { + label = "devinfo"; + reg = <0x1e0000 0x20000>; + read-only; + }; + }; + }; + + nand@1 { + reg = <1>; + compatible = "spi-nand"; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "kernel"; + reg = <0x0000000 0x5000000>; + }; + + partition@600000 { + label = "rootfs"; + reg = <0x0600000 0x4a00000>; + }; + + partition@5000000 { + label = "alt_kernel"; + reg = <0x5000000 0x5000000>; + }; + + partition@5600000 { + label = "alt_rootfs"; + reg = <0x5600000 0x4a00000>; + }; + + partition@a000000 { + label = "sysdiag"; + reg = <0xa000000 0x0200000>; + read-only; + }; + + partition@a200000 { + label = "syscfg"; + reg = <0xa200000 0x5e00000>; + read-only; + }; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&mdio { + status = "okay"; + pinctrl-0 = <&mdio_pins>; + pinctrl-names = "default"; + phy-reset-gpio = <&tlmm 62 GPIO_ACTIVE_HIGH>; +}; + +&tlmm { + mdio_pins: mdio_pinmux { + mux_mdio { + pins = "gpio53"; + function = "mdio"; + bias-pull-up; + }; + + mux_mdc { + pins = "gpio52"; + function = "mdc"; + bias-pull-up; + }; + }; + + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + pinmux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + }; + + pinmux_cs { + function = "gpio"; + pins = "gpio54", "gpio4"; + }; + + pinconf { + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + pinconf_cs { + pins = "gpio54", "gpio4"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; + + i2c_0_pins: i2c_0_pinmux { + mux { + function = "blsp_i2c0"; + pins = "gpio58", "gpio59"; + bias-disable; + }; + }; + + reset_pinmux { + mux { + pins = "gpio63"; + bias-pull-up; + }; + }; +}; + +&usb2 { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; + +&usb3 { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-whw01-v1"; + nvmem-cell-names = "pre-calibration"; + nvmem-cells = <&precal_art_1000>; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-whw01-v1"; + nvmem-cell-names = "pre-calibration"; + nvmem-cells = <&precal_art_5000>; +}; diff --git a/target/linux/ipq40xx/image/generic.mk b/target/linux/ipq40xx/image/generic.mk index 44880d157c..0ddff52ef8 100644 --- a/target/linux/ipq40xx/image/generic.mk +++ b/target/linux/ipq40xx/image/generic.mk @@ -662,6 +662,25 @@ define Device/linksys_mr8300 endef TARGET_DEVICES += linksys_mr8300 +define Device/linksys_whw01-v1 + $(call Device/FitzImage) + DEVICE_VENDOR := Linksys + DEVICE_MODEL := WHW01 + DEVICE_VARIANT := v1 + KERNEL_SIZE := 6144k + IMAGE_SIZE := 28704512 # 28032k minus linksys signature (256-bytes). + SOC := qcom-ipq4018 + BLOCKSIZE := 128k + PAGESIZE := 2048 + UBINIZE_OPTS := -E 5 # EOD marks to "hide" factory sig at EOF + IMAGES += factory.bin + IMAGE/factory.bin := append-kernel | pad-to $$$$(KERNEL_SIZE) | \ + append-ubi | linksys-image type=WHW01 | pad-to $$$$(PAGESIZE) | \ + check-size + DEVICE_PACKAGES := uboot-envtools kmod-leds-pca963x +endef +TARGET_DEVICES += linksys_whw01-v1 + define Device/luma_wrtq-329acn $(call Device/FitImage) DEVICE_VENDOR := Luma Home diff --git a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch index a6a082a2c8..99ea2e423e 100644 --- a/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.10/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -903,11 +903,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -903,11 +903,77 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ @@ -40,6 +40,7 @@ Signed-off-by: John Crispin + qcom-ipq4018-rt-ac58u.dtb \ + qcom-ipq4018-rutx10.dtb \ + qcom-ipq4018-wac510.dtb \ ++ qcom-ipq4018-whw01-v1.dtb \ + qcom-ipq4018-wre6606.dtb \ + qcom-ipq4018-wrtq-329acn.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \ diff --git a/target/linux/ipq40xx/patches-5.15/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-5.15/901-arm-boot-add-dts-files.patch index af1c695c26..f9b3c513bb 100644 --- a/target/linux/ipq40xx/patches-5.15/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-5.15/901-arm-boot-add-dts-files.patch @@ -10,7 +10,7 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -951,11 +951,75 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -951,11 +951,76 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-ipq4018-ap120c-ac.dtb \ qcom-ipq4018-ap120c-ac-bit.dtb \ qcom-ipq4018-jalapeno.dtb \ @@ -39,6 +39,7 @@ Signed-off-by: John Crispin + qcom-ipq4018-rt-ac58u.dtb \ + qcom-ipq4018-rutx10.dtb \ + qcom-ipq4018-wac510.dtb \ ++ qcom-ipq4018-whw01-v1.dtb \ + qcom-ipq4018-wre6606.dtb \ + qcom-ipq4018-wrtq-329acn.dtb \ qcom-ipq4019-ap.dk01.1-c1.dtb \