From: Sander Vanheule Date: Fri, 10 Jul 2020 11:41:21 +0000 (+0200) Subject: ath79: support for TP-Link EAP225 v3 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=b0ecae504b58bf65627138fe14eb605ad77224c9;p=openwrt%2Fstaging%2Fstintel.git ath79: support for TP-Link EAP225 v3 TP-Link EAP225 v3 is an AC1350 (802.11ac Wave-2) ceiling mount access point. Serial port access for debricking requires fine soldering. Device specifications: * SoC: QCA9563 @ 775MHz * RAM: 128MiB DDR2 * Flash: 16MiB SPI-NOR * Wireless 2.4GHz (SoC): b/g/n, 3x3 * Wireless 5Ghz (QCA9886): a/n/ac, 2x2 MU-MINO * Ethernet (AR8033): 1× 1GbE, 802.3at PoE Flashing instructions: * ssh into target device and run `cliclientd stopcs` * Upgrade with factory image via web interface Debricking: * Serial port can be soldered on PCB J3 (1: TXD, 2: RXD, 3: GND, 4: VCC) * Bridge unpopulated resistors R225 (TXD) and R237 (RXD). Do NOT bridge R230. * Use 3.3V, 115200 baud, 8n1 * Interrupt bootloader by holding CTRL+B during boot * tftp initramfs to flash via LuCI web interface setenv ipaddr 192.168.1.1 # default, change as required setenv serverip 192.168.1.10 # default, change as required tftp 0x80800000 initramfs.bin bootelf $fileaddr MAC addresses: MAC address (as on device label) is stored in device info partition at an offset of 8 bytes. ath9k device has same address as ethernet, ath10k uses address incremented by 1. From OEM boot log: Using interface ath0 with hwaddr b0:...:3e and ssid "..." Using interface ath10 with hwaddr b0:...:3f and ssid "..." Tested by forum user blinkstar88 Signed-off-by: Sander Vanheule --- diff --git a/target/linux/ath79/dts/qca9563_tplink_eap225-v3.dts b/target/linux/ath79/dts/qca9563_tplink_eap225-v3.dts new file mode 100644 index 0000000000..3d4950eaf0 --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_eap225-v3.dts @@ -0,0 +1,30 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca9563_tplink_eap2x5-1port.dtsi" + +/ { + compatible = "tplink,eap225-v3", "qca,qca9563"; + model = "TP-Link EAP225 v3"; + + aliases { + led-boot = &led_status_green; + led-failsafe = &led_status_amber; + led-running = &led_status_green; + led-upgrade = &led_status_amber; + }; + + leds { + compatible = "gpio-leds"; + + led_status_green: status_green { + label = "green:status"; + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + led_status_amber: status_amber { + label = "amber:status"; + gpios = <&gpio 9 GPIO_ACTIVE_HIGH>; + }; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 928b6c8903..5fbf4e2561 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -49,6 +49,7 @@ ath79_setup_interfaces() tplink,cpe610-v1|\ tplink,cpe610-v2|\ tplink,eap225-outdoor-v1|\ + tplink,eap225-v3|\ tplink,eap245-v1|\ tplink,re350k-v1|\ tplink,re355-v1|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 5be1c72ab0..ff15414ead 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -209,6 +209,7 @@ case "$FIRMWARE" in /lib/firmware/ath10k/QCA9888/hw2.0/board.bin ;; tplink,eap225-outdoor-v1|\ + tplink,eap225-v3|\ tplink,eap225-wall-v2|\ tplink,tl-wpa8630p-v2-int|\ tplink,tl-wpa8630p-v2.0-eu|\ diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index 343ea963c3..5088510af0 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -382,6 +382,17 @@ define Device/tplink_eap225-outdoor-v1 endef TARGET_DEVICES += tplink_eap225-outdoor-v1 +define Device/tplink_eap225-v3 + $(Device/tplink-eap2x5) + SOC := qca9563 + IMAGE_SIZE := 13824k + DEVICE_MODEL := EAP225 + DEVICE_VARIANT := v3 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + TPLINK_BOARD_ID := EAP225-V3 +endef +TARGET_DEVICES += tplink_eap225-v3 + define Device/tplink_eap225-wall-v2 $(Device/tplink-eap2x5) SOC := qca9561 diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index 4389cf0346..cb3cf69948 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -1327,6 +1327,35 @@ static struct device_info boards[] = { .last_sysupgrade_partition = "file-system" }, + /** Firmware layout for the EAP225 v3 */ + { + .id = "EAP225-V3", + .support_list = + "SupportList:\r\n" + "EAP225(TP-Link|UN|AC1350-D):3.0\r\n", + .support_trail = '\xff', + .soft_ver = NULL, + .soft_ver_compat_level = 1, + + .partitions = { + {"fs-uboot", 0x00000, 0x20000}, + {"partition-table", 0x20000, 0x02000}, + {"default-mac", 0x30000, 0x01000}, + {"support-list", 0x31000, 0x00100}, + {"product-info", 0x31100, 0x00400}, + {"soft-version", 0x32000, 0x00100}, + {"firmware", 0x40000, 0xd80000}, + {"user-config", 0xdc0000, 0x30000}, + {"mutil-log", 0xf30000, 0x80000}, + {"oops", 0xfb0000, 0x40000}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "file-system" + }, + /** Firmware layout for the EAP225-Wall v2 */ { .id = "EAP225-WALL-V2",