From: Pawel Dembicki Date: Wed, 21 Jul 2021 12:24:52 +0000 (+0200) Subject: kirkwood: add support for two clones from Endian X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=afd7ec3b57c3ff66f0a8ed250ed468e23cc9cb27;p=openwrt%2Fstaging%2Fthess.git kirkwood: add support for two clones from Endian They are Endian 4i Edge 200 and his clone Endian UTM Mini. Hardware: - SoC: Marvell 88F6281-A1 ARMv5TE Processor 1.2GHz - Ram: 512MB (4x Nanya NT5TU128M8GE-AC) - NAND Flash: 512MB (Micron 29F4G08AAC) - Lan 1-4: 4x GBE (Marvell 88E6171R-TFJ2) - Lan 5: 1x GBE (Marvell 88E1116R-NNC1) - Storage: MicroSD Slot - WLAN: MiniPCIe Slot present, and fitted with SparkLan WPEA-110N/E (Atheros AR9280 chipset) (ONLY Endian UTM Mini WLAN) - USB: 1x USB 2.0 port - Console: RJ-45 port - LEDs: 3x GPIO controlled Notes: - WLAN led (Endian UTM Mini) is drived by MPCIE card Installation by TFTP + serial: - Setup TFTP server and copy initramfs image - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.2 tftpboot 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Installation by USB + serial: - Copy initramfs image to fat32 usb drive - Connect pendrive to USB 2.0 front socket - Connect serial console - Stop booting in u-boot - Do: setenv bootargs 'console=ttyS0,115200n8 earlyprintk' saveenv usb reset fatload usb 0:1 0x1200000 openwrt-kirkwood-endian_4i-edge-200-initramfs-uImage bootm 0x1200000 - copy sysupgrade image via ssh. - run sysupgrade Signed-off-by: Pawel Dembicki --- diff --git a/target/linux/kirkwood/base-files/etc/board.d/02_network b/target/linux/kirkwood/base-files/etc/board.d/02_network index 972ee68fba..ebc70cfc2f 100644 --- a/target/linux/kirkwood/base-files/etc/board.d/02_network +++ b/target/linux/kirkwood/base-files/etc/board.d/02_network @@ -31,6 +31,9 @@ seagate,goflexnet|\ zyxel,nsa310s) ucidef_set_interface_lan "eth0" "dhcp" ;; +endian,4i-edge-200) + ucidef_set_interface_lan "port1 port2 port3 port4 eth1" + ;; linksys,e4200-v2|\ linksys,ea3500|\ linksys,ea4500) diff --git a/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac b/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac index 75e9e886d9..2a52b7962f 100644 --- a/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac +++ b/target/linux/kirkwood/base-files/lib/preinit/07_set_iface_mac @@ -19,6 +19,14 @@ preinit_set_mac_address() { ip link set dev dmz address $(macaddr_add $mac 8) 2>/dev/null ip link set dev dsl address $(macaddr_add $mac 9) 2>/dev/null ;; + endian,4i-edge-200) + mac=$(cat /sys/class/net/eth0/address) + + ip link set dev port1 address $mac 2>/dev/null + ip link set dev port2 address $(macaddr_add $mac 1) 2>/dev/null + ip link set dev port3 address $(macaddr_add $mac 2) 2>/dev/null + ip link set dev port4 address $(macaddr_add $mac 3) 2>/dev/null + ;; esac } diff --git a/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-4i-edge-200.dts b/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-4i-edge-200.dts new file mode 100644 index 0000000000..143dac97fe --- /dev/null +++ b/target/linux/kirkwood/files/arch/arm/boot/dts/kirkwood-4i-edge-200.dts @@ -0,0 +1,219 @@ +// SPDX-License-Identifier: GPL-2.0-or-later +/* + * Endian 4i Edge 200 Board Description + * Note: Endian UTM Mini is hardware clone of Endian Edge 200 + * Copyright 2021 Pawel Dembicki + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "Endian 4i Edge 200"; + compatible = "endian,4i-edge-200", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + aliases { + led-boot = &led_status_green; + led-failsafe = &led_status_orange; + led-running = &led_status_green; + led-upgrade = &led_status_orange; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + stdout-path = &uart0; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_led49 &pmx_led35 &pmx_led34>; + pinctrl-names = "default"; + + led_status_green: status_green { + label = "green:status"; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + }; + + led_status_orange: status_orange { + label = "orange:status"; + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + }; + + sdcard { + label = "orange:sdcard"; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + }; + }; +}; + +ð0 { + status = "okay"; +}; + +ð0port { + speed = <1000>; + duplex = <1>; +}; + +ð1 { + status = "okay"; +}; + +ð1port { + phy-handle = <ðphyb>; +}; + +&mdio { + status = "okay"; + + ethphyb: ethernet-phy@b { + reg = <0x0b>; + + marvell,reg-init = + /* link-activity, bi-color mode 4 */ + <3 0x10 0xfff0 0xf>; /* Reg 3,16 <- 0xzzzf */ + }; + + switch0: switch@11 { + compatible = "marvell,mv88e6085"; + reg = <0x11>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "port1"; + }; + + port@1 { + reg = <1>; + label = "port2"; + }; + + port@2 { + reg = <2>; + label = "port3"; + }; + + port@3 { + reg = <3>; + label = "port4"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + phy-mode = "rgmii-id"; + ethernet = <ð0port>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&nand { + status = "okay"; + pinctrl-0 = <&pmx_nand>; + pinctrl-names = "default"; + + partition@0 { + label = "u-boot"; + reg = <0x00000000 0x000a0000>; + read-only; + }; + + partition@a0000 { + label = "u-boot-env"; + reg = <0x000a0000 0x00060000>; + read-only; + }; + + partition@100000 { + label = "kernel"; + reg = <0x00100000 0x00400000>; + }; + + partition@500000 { + label = "ubi"; + reg = <0x00500000 0x1fb00000>; + }; +}; + +&pciec { + status = "okay"; +}; + +&pcie0 { + status = "okay"; +}; + +&pinctrl { + pinctrl-0 = <&pmx_sysrst>; + pinctrl-names = "default"; + + pmx_sysrst: pmx-sysrst { + marvell,pins = "mpp6"; + marvell,function = "sysrst"; + }; + + pmx_sdio_cd: pmx-sdio-cd { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_led34: pmx_led34 { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + pmx_led35: pmx_led35 { + marvell,pins = "mpp35"; + marvell,function = "gpio"; + }; + + pmx_led49: pmx_led49 { + marvell,pins = "mpp49"; + marvell,function = "gpio"; + }; +}; + +&rtc { + status = "okay"; +}; + +&sata_phy0 { + status = "disabled"; +}; + +&sata_phy1 { + status = "disabled"; +}; + +&sdio { + pinctrl-0 = <&pmx_sdio_cd>; + pinctrl-names = "default"; + status = "okay"; + cd-gpios = <&gpio0 28 9>; +}; + +&uart0 { + status = "okay"; +}; + +&usb0 { + status = "okay"; +}; diff --git a/target/linux/kirkwood/image/Makefile b/target/linux/kirkwood/image/Makefile index eb3d684c80..4a2ca8d68e 100644 --- a/target/linux/kirkwood/image/Makefile +++ b/target/linux/kirkwood/image/Makefile @@ -140,6 +140,17 @@ define Device/ctera_c200-v1 endef TARGET_DEVICES += ctera_c200-v1 +define Device/endian_4i-edge-200 + DEVICE_VENDOR := Endian + DEVICE_MODEL := 4i Edge 200 + DEVICE_ALT0_VENDOR := Endian + DEVICE_ALT0_MODEL := UTM Mini Firewall + DEVICE_PACKAGES := kmod-ath9k kmod-mvsdio wpad-basic-wolfssl + KERNEL_SIZE := 4096k + IMAGES := sysupgrade.bin +endef +TARGET_DEVICES += endian_4i-edge-200 + define Device/globalscale_sheevaplug DEVICE_VENDOR := Globalscale DEVICE_MODEL := Sheevaplug