From: Chris Blake Date: Sun, 5 May 2019 17:56:03 +0000 (-0500) Subject: ath79: add support for Aruba AP-105 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=aee5c9861996983394ac49f91a831c4641a4bf83;p=openwrt%2Fstaging%2Fdangole.git ath79: add support for Aruba AP-105 SoC: Atheros AR7161-8C1A @ 680 MHz RAM: 128MB - 2x Etron Technology EM6AB160TSA-5G NOR: 16MB - 1x MXIC MX25L12845EMI-10G (SPI-NOR) WI1: Atheros AR9223-AC1A 802.11bgn WI2: Atheros AR9220-AC1A 802.11an ETH: Atheros AR8021-BL1E + PoE LED: Dual-Color Power/Status, Ethernet, WLAN2G and WLAN5G BTN: 1 x Reset I2C: AT97SC4303s TPM (needs driver!) CON: RS232-level 8P8C/RJ45 Console Port - 9600 Baud Factory installation: - Needs a u-boot replacement. See Wiki for information on how to do a in-circut flash with a SPI-Flasher like a CH314A or flashrom. Wiki page can be found at https://openwrt.org/toh/aruba/aruba_ap-105 - Be careful when dis- and reassembling the device to not squish any of the antenna cables in the process! - Be sure to make a full 16 MiB backup of your device before flashing the new u-boot! This is needed if you ever have interest in reverting back to stock firmware. Not working: - TPM (needs a driver) Signed-off-by: Chris Blake --- diff --git a/target/linux/ath79/base-files/etc/board.d/02_network b/target/linux/ath79/base-files/etc/board.d/02_network index 5892baca80..897b59af33 100755 --- a/target/linux/ath79/base-files/etc/board.d/02_network +++ b/target/linux/ath79/base-files/etc/board.d/02_network @@ -9,6 +9,7 @@ ath79_setup_interfaces() local board="$1" case "$board" in + aruba,ap-105|\ avm,fritz300e|\ devolo,dvl1200i|\ devolo,dvl1750c|\ diff --git a/target/linux/ath79/dts/ar7161_aruba_ap-105.dts b/target/linux/ath79/dts/ar7161_aruba_ap-105.dts new file mode 100644 index 0000000000..45d4d03f31 --- /dev/null +++ b/target/linux/ath79/dts/ar7161_aruba_ap-105.dts @@ -0,0 +1,190 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include +#include + +#include "ar7100.dtsi" + +/ { + compatible = "aruba,ap-105", "qca,ar7161"; + model = "Aruba AP-105"; + + chosen { + bootargs = "console=ttyS0,9600"; + }; + + aliases { + led-boot = &power_green; + led-failsafe = &power_red; + led-running = &power_green; + led-upgrade = &power_green; + }; + + extosc: ref { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-output-names = "ref"; + clock-frequency = <40000000>; + }; + + leds { + compatible = "gpio-leds"; + + power_green: power_green { + label = "ap-105:green:power"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + power_red: power_red { + label = "ap-105:red:power"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + panic-indicator; + }; + + wifi_2g_red: wifi_2g_red { + label = "ap-105:red:wlan2g"; + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; + }; + + wifi_5g_red: wifi_5g_red { + label = "ap-105:red:wlan5g"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + }; + + ath9k-leds { + compatible = "gpio-leds"; + + wifi_2g_green { + label = "ap-105:green:wlan2g"; + gpios = <&ath9k0 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + wifi_5g_green { + label = "ap-105:green:wlan5g"; + gpios = <&ath9k1 5 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy1tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = ; + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; + }; + }; + + i2c { + compatible = "i2c-gpio"; + + sda-gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + scl-gpios = <&gpio 4 GPIO_ACTIVE_LOW>; + + /* can be removed on 4.19 */ + gpios = <&gpio 5 GPIO_ACTIVE_LOW>, + <&gpio 4 GPIO_ACTIVE_LOW>; + + #address-cells = <1>; + #size-cells = <0>; + + tpm@29 { + compatible = "atmel,at97sc3203s"; + reg = <0x29>; + + /* triggering it, will also kill system */ + reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&pcie0 { + status = "okay"; + + ath9k0: wifi@0,11 { /* 2.4 GHz */ + compatible = "pci168c,0029"; + mtd-mac-address = <&hwinfo 0x1c>; + mtd-mac-address-increment = <1>; + reg = <0x8800 0 0 0 0>; + #gpio-cells = <2>; + gpio-controller; + }; + + ath9k1: wifi@0,12 { /* 5 GHz */ + compatible = "pci168c,0029"; + mtd-mac-address = <&hwinfo 0x1c>; + mtd-mac-address-increment = <2>; + reg = <0x9000 0 0 0 0>; + #gpio-cells = <2>; + gpio-controller; + }; +}; + +&uart { + status = "okay"; +}; + +&mdio0 { + status = "okay"; + + phy-mask = <0x1>; + + phy0: ethernet-phy@0 { + reg = <0>; + }; +}; + +ð0 { + status = "okay"; + mtd-mac-address = <&hwinfo 0x1c>; + + pll-data = <0x00110000 0x00001099 0x00991099>; + + phy-mode = "rgmii"; + phy-handle = <&phy0>; +}; + +&spi { + status = "okay"; + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x40000>; + read-only; + }; + + partition@40000 { + label = "firmware"; + reg = <0x40000 0xfa0000>; + compatible = "denx,uimage"; + }; + + hwinfo: partition@fe0000 { + label = "hwinfo"; + reg = <0xfe0000 0x10000>; + read-only; + }; + + partition@ff0000 { + label = "u-boot-env"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; +}; diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index a96c9d279a..dd5843d436 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -75,6 +75,14 @@ define Device/seama SEAMA_SIGNATURE := endef +define Device/aruba_ap-105 + ATH_SOC := ar7161 + DEVICE_TITLE := Aruba AP-105 + IMAGE_SIZE := 16000k + DEVICE_PACKAGES := kmod-i2c-core kmod-i2c-gpio kmod-tpm-i2c-atmel +endef +TARGET_DEVICES += aruba_ap-105 + define Device/avm_fritz300e ATH_SOC := ar7242 DEVICE_TITLE := AVM FRITZ!WLAN Repeater 300E