From: Andrew Cameron Date: Mon, 12 Apr 2021 18:24:33 +0000 (-0500) Subject: ath79: add support for TP-Link CPE710-v1 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=ac03e246351fbfa98e98f0319cce3a8663f836d3;p=openwrt%2Fstaging%2Fjow.git ath79: add support for TP-Link CPE710-v1 TP-Link CPE710-v1 is an outdoor wireless CPE for 5 GHz with one Ethernet port based on the AP152 reference board Specifications: - SoC: QCA9563-AL3A MIPS 74kc @ 775MHz, AHB @ 258MHz - RAM: 128MiB DDR2 @ 650MHz - Flash: 16MiB SPI NOR Based on the GD25Q128 - Wi-Fi 5Ghz: ath10k chip (802.11ac for up to 867Mbps on 5GHz wireless data rate) Based on the QCA9896 - Ethernet: one 1GbE port - 23dBi high-gain directional 2×2 MIMO antenna and a dedicated metal reflector - Power, LAN, WLAN5G Blue LEDs - 3x Blue LEDs Flashing instructions: Flash factory image through stock firmware WEB UI or through TFTP To get to TFTP recovery just hold reset button while powering on for around 30-40 seconds and release. Rename factory image to recovery.bin Stock TFTP server IP:192.168.0.100 Stock device TFTP address:192.168.0.254 Signed-off-by: Andrew Cameron [convert to nvmem, fix MAC assignment in 11-ath10k-caldata] Signed-off-by: Adrian Schmutzler --- diff --git a/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts b/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts new file mode 100644 index 0000000000..c97d1652cb --- /dev/null +++ b/target/linux/ath79/dts/qca9563_tplink_cpe710-v1.dts @@ -0,0 +1,152 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qca956x.dtsi" + +#include +#include + +/ { + model = "TP-Link CPE710 v1"; + compatible = "tplink,cpe710-v1", "qca,qca9563"; + + aliases { + label-mac-device = ð0; + led-boot = &led_lan; + led-failsafe = &led_lan; + led-upgrade = &led_lan; + }; + + leds { + compatible = "gpio-leds"; + + led_lan: lan { + label = "blue:lan"; + gpios = <&gpio 5 GPIO_ACTIVE_LOW>; + }; + + wlan5g { + label = "blue:wlan5g"; + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "Reset button"; + linux,code = ; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&spi { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <40000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x040000>; + read-only; + }; + + partition@40000 { + label = "u-boot-env"; + reg = <0x040000 0x010000>; + }; + + partition@50000 { + label = "partition-table"; + reg = <0x050000 0x010000>; + read-only; + }; + + info: partition@60000 { + label = "info"; + reg = <0x060000 0x010000>; + read-only; + }; + + partition@70000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x070000 0xf50000>; + }; + + partition@fc0000 { + label = "config"; + reg = <0xfc0000 0x030000>; + read-only; + }; + + art: partition@ff0000 { + label = "art"; + reg = <0xff0000 0x010000>; + read-only; + }; + }; + }; +}; + +&pinmux { + mdio_pins: mdio_pins { + /* GPIO 10 as MDIO(0x20), GPIO 8 as MDC(0x21) */ + pinctrl-single,bits = <0x8 0x00200021 0x00ff00ff>; + }; +}; + +&mdio0 { + status = "okay"; + + pinctrl-names = "default"; + pinctrl-0 = <&mdio_pins>; + + phy-mask = <0x10>; + + phy4: ethernet-phy@4 { + reg = <4>; + reset-gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; +}; + +ð0 { + status = "okay"; + + phy-handle = <&phy4>; + phy-mode = "sgmii"; + + nvmem-cells = <&macaddr_info_8>; + nvmem-cell-names = "mac-address"; + + qca956x-serdes-fixup; + + gmac-config { + device = <&gmac>; + }; +}; + +&info { + compatible = "nvmem-cells"; + #address-cells = <1>; + #size-cells = <1>; + + macaddr_info_8: macaddr@8 { + reg = <0x8 0x6>; + }; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index ffc6f3086e..1c112b4952 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -169,7 +169,8 @@ enterasys,ws-ap3705i|\ openmesh,mr900-v1|\ openmesh,mr900-v2|\ openmesh,mr1750-v1|\ -openmesh,mr1750-v2) +openmesh,mr1750-v2|\ +tplink,cpe710-v1) ucidef_set_led_netdev "lan" "LAN" "blue:lan" "eth0" ;; compex,wpj344-16m|\ diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index e2c6f9feac..af4cf08ce0 100644 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -63,6 +63,7 @@ ath79_setup_interfaces() tplink,cpe510-v3|\ tplink,cpe610-v1|\ tplink,cpe610-v2|\ + tplink,cpe710-v1|\ tplink,eap225-outdoor-v1|\ tplink,eap225-v3|\ tplink,eap245-v1|\ diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 5ba1a7a8ff..7f8c1b1143 100644 --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -236,6 +236,12 @@ case "$FIRMWARE" in ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin ;; + tplink,cpe710-v1) + caldata_extract "art" 0x5000 0x2f20 + ath10k_patch_mac $(mtd_get_mac_binary info 0x8) + ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \ + /lib/firmware/ath10k/QCA9888/hw2.0/board.bin + ;; tplink,eap225-outdoor-v1|\ tplink,eap225-v3|\ tplink,eap225-wall-v2|\ diff --git a/target/linux/ath79/image/generic-tp-link.mk b/target/linux/ath79/image/generic-tp-link.mk index b6755fe547..363be289c6 100644 --- a/target/linux/ath79/image/generic-tp-link.mk +++ b/target/linux/ath79/image/generic-tp-link.mk @@ -362,6 +362,17 @@ define Device/tplink_cpe610-v2 endef TARGET_DEVICES += tplink_cpe610-v2 +define Device/tplink_cpe710-v1 + $(Device/tplink-safeloader-uimage) + SOC := qca9563 + IMAGE_SIZE := 15680k + DEVICE_MODEL := CPE710 + DEVICE_VARIANT := v1 + DEVICE_PACKAGES := kmod-ath10k-ct ath10k-firmware-qca9888-ct + TPLINK_BOARD_ID := CPE710V1 +endef +TARGET_DEVICES += tplink_cpe710-v1 + define Device/tplink-eap2x5 $(Device/tplink-safeloader) LOADER_TYPE := elf diff --git a/tools/firmware-utils/src/tplink-safeloader.c b/tools/firmware-utils/src/tplink-safeloader.c index b20d1fdd30..03329a3926 100644 --- a/tools/firmware-utils/src/tplink-safeloader.c +++ b/tools/firmware-utils/src/tplink-safeloader.c @@ -534,6 +534,43 @@ static struct device_info boards[] = { .first_sysupgrade_partition = "os-image", .last_sysupgrade_partition = "support-list", }, + /** Firmware layout for the CPE710 V1 */ + { + .id = "CPE710V1", + .vendor = "CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n", + .support_list = + "SupportList:\r\n" + "CPE710(TP-LINK|UN|AC866-5|00000000):1.0\r\n" + "CPE710(TP-LINK|EU|AC866-5|45550000):1.0\r\n" + "CPE710(TP-LINK|US|AC866-5|55530000):1.0\r\n" + "CPE710(TP-LINK|UN|AC866-5):1.0\r\n" + "CPE710(TP-LINK|EU|AC866-5):1.0\r\n" + "CPE710(TP-LINK|US|AC866-5):1.0\r\n", + .part_trail = 0xff, + .soft_ver = SOFT_VER_DEFAULT, + + .partitions = { + {"fs-uboot", 0x00000, 0x50000}, + {"partition-table", 0x50000, 0x02000}, + {"default-mac", 0x60000, 0x00020}, + {"serial-number", 0x60100, 0x00020}, + {"product-info", 0x61100, 0x00100}, + {"device-info", 0x61400, 0x00400}, + {"signature", 0x62000, 0x00400}, + {"device-id", 0x63000, 0x00100}, + {"firmware", 0x70000, 0xf40000}, + {"soft-version", 0xfb0000, 0x00100}, + {"support-list", 0xfb1000, 0x01000}, + {"user-config", 0xfc0000, 0x10000}, + {"default-config", 0xfd0000, 0x10000}, + {"log", 0xfe0000, 0x10000}, + {"radio", 0xff0000, 0x10000}, + {NULL, 0, 0} + }, + + .first_sysupgrade_partition = "os-image", + .last_sysupgrade_partition = "support-list", + }, { .id = "WBS210",