From: Kyson Lok Date: Wed, 17 May 2017 10:18:45 +0000 (+0800) Subject: ramips: add support for GL-inet GL-MT300N-V2 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=abbfcc85259a4f6658c61e99dd3d2d3567e3eb3a;p=openwrt%2Fstaging%2Fblogic.git ramips: add support for GL-inet GL-MT300N-V2 This patch adds supports for the GL-inet GL-MT300N-V2. Specification: - SoC: MediaTek MT7628AN - Flash: 16 MiB (W25Q128FVSG) - RAM: 128 MiB DDR - Ethernet: 1 x WAN (100 Mbps) and 1 x LAN (100 Mbps) - USB: 1 x USB 2.0 port - Button: 1 x switch button, 1 x reset button - LED: 3 x LEDS (system power led is not GPIO controller) - UART: 1 x UART on PCB (JP1: 3.3V, RX, TX, GND) Installation through Luci: - The original firmware is LEDE, so both LuCI or sysupgrade can be used. - Do not keep settings, for sysupgrade please use the -n option. Installation through bootloader webserver: - Plug power and hold reset button until red LED blink to bright. - Install sysupgrade image using web interface on 192.168.1.1. Signed-off-by: Kyson Lok [match maximum image size with firmware partition] Signed-off-by: Mathias Kresin --- diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds index 2a35fc4bc21a..b08f35268bd2 100755 --- a/target/linux/ramips/base-files/etc/board.d/01_leds +++ b/target/linux/ramips/base-files/etc/board.d/01_leds @@ -189,6 +189,9 @@ gl-mt300n|\ gl-mt750) set_wifi_led "$board:wlan" ;; +gl-mt300n-v2) + set_wifi_led "$board:red:wlan" + ;; hc5661|\ hc5661a) ucidef_set_led_default "system" "system" "$board:blue:system" "1" diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network index 6d93f2ccaa89..9dd5823639d2 100755 --- a/target/linux/ramips/base-files/etc/board.d/02_network +++ b/target/linux/ramips/base-files/etc/board.d/02_network @@ -180,6 +180,10 @@ ramips_setup_interfaces() ucidef_add_switch "switch0" \ "1:lan" "2:lan" "3:lan" "4:lan" "0:wan" "6@eth0" ;; + gl-mt300n-v2) + ucidef_add_switch "switch0" \ + "1:lan" "0:wan" "6@eth0" + ;; awapn2403) ucidef_add_switch "switch0" \ "0:lan" "1:wan" "6@eth0" diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index e37f9cfda401..26d7f627cd2f 100644 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -166,6 +166,9 @@ get_status_led() { miwifi-nano) status_led="$board:blue:status" ;; + gl-mt300n-v2) + status_led="$board:red:wlan" + ;; m4-4M|\ m4-8M) status_led="m4:blue:status" diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index 421315937850..4b60a07ee0c9 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -217,6 +217,9 @@ ramips_board_detect() { *"GL-MT750") name="gl-mt750" ;; + *"GL-MT300N-V2") + name="gl-mt300n-v2" + ;; *"HC5661") name="hc5661" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index 32bc453497c4..6aad4c96019b 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -65,6 +65,7 @@ platform_check_image() { gl-mt300a|\ gl-mt300n|\ gl-mt750|\ + gl-mt300n-v2|\ hc5*61|\ hc5661a|\ hg255d|\ diff --git a/target/linux/ramips/dts/GL-MT300N-V2.dts b/target/linux/ramips/dts/GL-MT300N-V2.dts new file mode 100644 index 000000000000..e40c4cf7dfea --- /dev/null +++ b/target/linux/ramips/dts/GL-MT300N-V2.dts @@ -0,0 +1,133 @@ +/dts-v1/; + +#include "mt7628an.dtsi" + +#include +#include + +/{ + compatible = "gl-inet,gl-mt300n-v2", "ralink,mt7620an-soc"; + model = "GL-MT300N-V2"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x8000000>; + }; + + gpio-leds { + compatible = "gpio-leds"; + + wan { + label = "gl-mt300n-v2:blue:wan"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + + wlan { + label = "gl-mt300n-v2:red:wlan"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-keys { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + + reset { + label = "reset"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + BTN_0 { + label = "BTN_0"; + gpios = <&gpio0 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + BTN_1 { + label = "BTN_1"; + gpios = <&gpio0 3 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + gpio_export { + compatible = "gpio-export"; + #size-cells = <0>; + + usb { + gpio-export,name = "usb"; + gpio-export,output = <1>; + gpios = <&gpio0 11 GPIO_ACTIVE_LOW>; + }; + }; + +}; + +&pinctrl { + state_default: pinctrl0 { + gpio { + ralink,group = "wdt", "gpio", "wled_an", "p0led_an", "i2s"; + ralink,function = "gpio"; + }; + }; +}; + +ðernet { + mtd-mac-address = <&factory 0x4000>; +}; + +&wmac { + status = "okay"; + ralink,mtd-eeprom = <&factory 0x0>; +}; + +&spi0 { + status = "okay"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <10000000>; + m25p,chunked-io = <32>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x30000>; + read-only; + }; + + partition@30000 { + label = "u-boot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + + factory: partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + + partition@50000 { + label = "firmware"; + reg = <0x50000 0xfb0000>; + }; + }; +}; + +&ehci { + status = "okay"; +}; + +&ohci { + status = "okay"; +}; diff --git a/target/linux/ramips/image/mt7628.mk b/target/linux/ramips/image/mt7628.mk index 6bb04ea38c45..f8bd2c18b241 100644 --- a/target/linux/ramips/image/mt7628.mk +++ b/target/linux/ramips/image/mt7628.mk @@ -26,6 +26,14 @@ define Device/miwifi-nano endef TARGET_DEVICES += miwifi-nano +define Device/gl-mt300n-v2 + DTS := GL-MT300N-V2 + IMAGE_SIZE := 16064k + DEVICE_TITLE := GL-iNet GL-MT300N-V2 + DEVICE_PACKAGES := kmod-usb2 kmod-usb-ohci +endef +TARGET_DEVICES += gl-mt300n-v2 + define Device/vocore2 DTS := VOCORE2 IMAGE_SIZE := $(ralink_default_fw_size_16M)