From: John Crispin Date: Tue, 2 Feb 2021 15:29:58 +0000 (+0100) Subject: mediatek: add Linksys E8450 support X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=aa94e34c1d7ce40684ec01b8ddc056548ecd34f0;p=openwrt%2Fstaging%2Fwigyori.git mediatek: add Linksys E8450 support The Linksys E8450, also known as Belkin RT3200, is a dual-band IEEE 802.11bgn/ac/ax router based on MediaTek MT7622BV and MediaTek MT7915AN chips. FCC: K7S-03571 and K7S-03572 Hardware highlights: - CPU: MediaTek MT7622BV (2x ARM Cortex-A53 @ 1350 MHz max.) - RAM: 512MB DDR3 - Flash: 128MB SPI-NAND (2k+64) - Ethernet: MT7531BE switch with 5 1000Base-T ports CPU port connected with 2500Base-X - WiFi 2.4 GHz: 802.11bgn 4T4R built-in antennas MT7622VB built-in - WiFi 5 GHz: 802.11ac/ax 4T4R built-in antennas MT7915AN chip on-board via PCIe MT7975AN front-end - Buttons: Reset and WPS - LEDS: 3 user controllable LEDs, 4 wired to switch - USB: USB2.0, single port - no Bluetooth (supported by SoC, not wired on board) - Serial: JST PH 2.0MM 6 Pin connector inside device ----_____________---- [ GND RX - TX - - ] --------------------- - JTAG: unpopulated ARM JTAG 20-pin connector (works) This commit adds support for the device in a way that is compatible with the vendor firmware's bootloader and dual-boot flash layout, the resulting image can directly be flashed using the vendor firmware. Signed-off-by: Daniel Golle Signed-off-by: John Crispin Signed-off-by: Felix Fietkau --- diff --git a/target/linux/mediatek/dts/mt7622-linksys-e8450.dts b/target/linux/mediatek/dts/mt7622-linksys-e8450.dts new file mode 100644 index 0000000000..719e1d9230 --- /dev/null +++ b/target/linux/mediatek/dts/mt7622-linksys-e8450.dts @@ -0,0 +1,486 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR MIT) + +/dts-v1/; +#include +#include + +#include "mt7622.dtsi" +#include "mt6380.dtsi" + +/ { + model = "Linksys E8450"; + compatible = "linksys,e8450", "mediatek,mt7622"; + + aliases { + serial0 = &uart0; + led-boot = &led_power; + led-failsafe = &led_power; + led-running = &led_power; + led-upgrade = &led_power; + }; + + chosen { + stdout-path = "serial0:115200n8"; + bootargs = "earlycon=uart8250,mmio32,0x11002000 console=ttyS0,115200n1 swiotlb=512"; + }; + + cpus { + cpu@0 { + proc-supply = <&mt6380_vcpu_reg>; + sram-supply = <&mt6380_vm_reg>; + }; + + cpu@1 { + proc-supply = <&mt6380_vcpu_reg>; + sram-supply = <&mt6380_vm_reg>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + factory { + label = "reset"; + linux,code = ; + gpios = <&pio 0 GPIO_ACTIVE_LOW>; + }; + + wps { + label = "wps"; + linux,code = ; + gpios = <&pio 102 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led_power: power_blue { + label = "power:blue"; + gpios = <&pio 95 GPIO_ACTIVE_LOW>; + default-state = "on"; + }; + + power_orange { + label = "power:orange"; + gpios = <&pio 96 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + inet_blue { + label = "inet:blue"; + gpios = <&pio 97 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + + inet_orange { + label = "inet:orange"; + gpios = <&pio 98 GPIO_ACTIVE_LOW>; + default-state = "off"; + }; + }; + + memory { + reg = <0 0x40000000 0 0x40000000>; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "fixed-1.8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "fixed-3.3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + reg_5v: regulator-5v { + compatible = "regulator-fixed"; + regulator-name = "fixed-5V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + regulator-always-on; + }; +}; + +&bch { + status = "okay"; +}; + +&btif { + status = "okay"; +}; + +&cir { + pinctrl-names = "default"; + pinctrl-0 = <&irrx_pins>; + status = "okay"; +}; + +ð { + pinctrl-names = "default"; + pinctrl-0 = <ð_pins>; + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + + mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + switch@0 { + compatible = "mediatek,mt7531"; + reg = <0>; + reset-gpios = <&pio 54 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "2500base-x"; + + fixed-link { + speed = <2500>; + full-duplex; + pause; + }; + }; + }; + }; + + }; +}; + +&pcie0 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie0_pins>; + status = "okay"; +}; + +&pcie1 { + pinctrl-names = "default"; + pinctrl-0 = <&pcie1_pins>; + status = "okay"; +}; + +&slot0 { + mt7915@0,0 { + reg = <0x0000 0 0 0 0>; + mediatek,mtd-eeprom = <&factory 0x05000>; + }; +}; + +&pio { + /* Attention: GPIO 90 is used to switch between PCIe@1,0 and + * SATA functions. i.e. output-high: PCIe, output-low: SATA + */ +// asm_sel { +// gpio-hog; +// gpios = <90 GPIO_ACTIVE_HIGH>; +// output-high; +// }; + + eth_pins: eth-pins { + mux { + function = "eth"; + groups = "mdc_mdio", "rgmii_via_gmac2"; + }; + }; + + irrx_pins: irrx-pins { + mux { + function = "ir"; + groups = "ir_1_rx"; + }; + }; + + irtx_pins: irtx-pins { + mux { + function = "ir"; + groups = "ir_1_tx"; + }; + }; + + pcie0_pins: pcie0-pins { + mux { + function = "pcie"; + groups = "pcie0_pad_perst", + "pcie0_1_waken", + "pcie0_1_clkreq"; + }; + }; + + pcie1_pins: pcie1-pins { + mux { + function = "pcie"; + groups = "pcie1_pad_perst", + "pcie1_0_waken", + "pcie1_0_clkreq"; + }; + }; + + pmic_bus_pins: pmic-bus-pins { + mux { + function = "pmic"; + groups = "pmic_bus"; + }; + }; + + pwm7_pins: pwm1-2-pins { + mux { + function = "pwm"; + groups = "pwm_ch7_2"; + }; + }; + + wled_pins: wled-pins { + mux { + function = "led"; + groups = "wled"; + }; + }; + + /* Serial NAND is shared pin with SPI-NOR */ + serial_nand_pins: serial-nand-pins { + mux { + function = "flash"; + groups = "snfi"; + }; + }; + + spic0_pins: spic0-pins { + mux { + function = "spi"; + groups = "spic0_0"; + }; + }; + + spic1_pins: spic1-pins { + mux { + function = "spi"; + groups = "spic1_0"; + }; + }; + + uart0_pins: uart0-pins { + mux { + function = "uart"; + groups = "uart0_0_tx_rx" ; + }; + }; + + uart2_pins: uart2-pins { + mux { + function = "uart"; + groups = "uart2_1_tx_rx" ; + }; + }; + + watchdog_pins: watchdog-pins { + mux { + function = "watchdog"; + groups = "watchdog"; + }; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm7_pins>; + status = "okay"; +}; + +&pwrap { + pinctrl-names = "default"; + pinctrl-0 = <&pmic_bus_pins>; + + status = "okay"; +}; + +&sata { + status = "disabled"; +}; + +&sata_phy { + status = "disabled"; +}; + +&snfi { + pinctrl-names = "default"; + pinctrl-0 = <&serial_nand_pins>; + status = "okay"; + + spi_nand@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spi-nand"; + spi-max-frequency = <104000000>; + reg = <0>; + + mediatek,bmt-v2; + mediatek,bmt-table-size = <0x1000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "Preloader"; + reg = <0x00000 0x0080000>; + read-only; + }; + + partition@80000 { + label = "ATF"; + reg = <0x80000 0x0040000>; + }; + + partition@c0000 { + label = "u-boot"; + reg = <0xc0000 0x0080000>; + }; + + partition@140000 { + label = "u-boot-env"; + reg = <0x140000 0x0080000>; + }; + + factory: partition@1c0000 { + label = "factory"; + reg = <0x1c0000 0x0100000>; + }; + + partition@300000 { + label = "devinfo"; + reg = <0x300000 0x020000>; + }; + + partition@320000 { + label = "senv"; + reg = <0x320000 0x020000>; + }; + + partition@360000 { + label = "bootseq"; + reg = <0x360000 0x020000>; + }; + + partition@500000 { + label = "firmware1"; + compatible = "denx,fit"; + openwrt,cmdline-match = "mtdparts=master"; + reg = <0x500000 0x1E00000>; + }; + + partition@2300000 { + label = "firmware2"; + compatible = "denx,fit"; + openwrt,cmdline-match = "mtdparts=slave"; + reg = <0x2300000 0x1E00000>; + }; + + partition@4100000 { + label = "data"; + reg = <0x4100000 0x1900000>; + }; + + partition@5100000 { + label = "mfg"; + reg = <0x5a00000 0x1400000>; + }; + }; + }; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spic0_pins>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spic1_pins>; + status = "okay"; +}; + +&ssusb { + vusb33-supply = <®_3p3v>; + vbus-supply = <®_5v>; + status = "okay"; +}; + +&u3phy { + status = "okay"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; + status = "okay"; +}; + +&watchdog { + pinctrl-names = "default"; + pinctrl-0 = <&watchdog_pins>; + status = "okay"; +}; + +&wmac { + mediatek,mtd-eeprom = <&factory 0x0000>; + status = "okay"; +}; diff --git a/target/linux/mediatek/image/mt7622.mk b/target/linux/mediatek/image/mt7622.mk index 9bf4d6a97a..dce1fb2055 100644 --- a/target/linux/mediatek/image/mt7622.mk +++ b/target/linux/mediatek/image/mt7622.mk @@ -38,6 +38,18 @@ define Device/elecom_wrc-2533gent endef TARGET_DEVICES += elecom_wrc-2533gent +define Device/linksys_e8450 + DEVICE_VENDOR := Linksys + DEVICE_MODEL := E8450 + DEVICE_ALT0_VENDOR := Belkin + DEVICE_ALT0_MODEL := RT3200 + DEVICE_DTS := mt7622-linksys-e8450 + DEVICE_DTS_DIR := ../dts + DEVICE_PACKAGES := kmod-usb-ohci kmod-usb2 kmod-usb3 kmod-ata-ahci-mtk \ + kmod-mt7615e kmod-mt7615-firmware kmod-mt7915e +endef +TARGET_DEVICES += linksys_e8450 + define Device/mediatek_mt7622-rfb1 DEVICE_VENDOR := MediaTek DEVICE_MODEL := MTK7622 rfb1 AP diff --git a/target/linux/mediatek/mt7622/base-files/etc/board.d/01_leds b/target/linux/mediatek/mt7622/base-files/etc/board.d/01_leds new file mode 100755 index 0000000000..e74944a65f --- /dev/null +++ b/target/linux/mediatek/mt7622/base-files/etc/board.d/01_leds @@ -0,0 +1,18 @@ +#!/bin/sh + +. /lib/functions/leds.sh +. /lib/functions/uci-defaults.sh + +board=$(board_name) + +board_config_update + +case $board in +linksys,e8450) + ucidef_set_led_netdev "wan" "WAN" "inet:blue" "wan" + ;; +esac + +board_config_flush + +exit 0 diff --git a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network index 3a409c8ec9..3d2b9ffe49 100755 --- a/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network +++ b/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network @@ -10,9 +10,8 @@ mediatek_setup_interfaces() case $board in bananapi,bpi-r64-rootdisk|\ - bananapi,bpi-r64) - ucidef_set_interfaces_lan_wan "lan0 lan1 lan2 lan3" wan - ;; + bananapi,bpi-r64|\ + linksys,e8450|\ mediatek,mt7622-rfb1) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4" wan ;; @@ -31,7 +30,15 @@ mediatek_setup_macs() local board="$1" case $board in + linksys,e8450) + wan_mac=$(mtd_get_mac_ascii devinfo wan_mac_addr) + lan_mac=$(mtd_get_mac_ascii devinfo lan_mac_addr) + label_mac=$wan_mac + ;; esac + [ -n "$lan_mac" ] && ucidef_set_interface_macaddr "lan" $lan_mac + [ -n "$wan_mac" ] && ucidef_set_interface_macaddr "wan" $wan_mac + [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac } board_config_update diff --git a/target/linux/mediatek/mt7622/base-files/etc/init.d/bootcount b/target/linux/mediatek/mt7622/base-files/etc/init.d/bootcount new file mode 100755 index 0000000000..bc4eeb6530 --- /dev/null +++ b/target/linux/mediatek/mt7622/base-files/etc/init.d/bootcount @@ -0,0 +1,11 @@ +#!/bin/sh /etc/rc.common + +START=99 + +boot() { + case $(board_name) in + linksys,e8450) + mtd erase senv || true + ;; + esac +} diff --git a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh index 8144476943..95ac8b5657 100755 --- a/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh +++ b/target/linux/mediatek/mt7622/base-files/lib/upgrade/platform.sh @@ -10,6 +10,14 @@ platform_do_upgrade() { mediatek,mt7622,ubi) nand_do_upgrade "$1" ;; + linksys,e8450) + if grep -q mtdparts=slave /proc/cmdline; then + PART_NAME=firmware2 + else + PART_NAME=firmware1 + fi + default_do_upgrade "$1" + ;; *) default_do_upgrade "$1" ;; diff --git a/target/linux/mediatek/patches-5.10/340-mtd-spinand-Add-support-for-the-Fidelix-FM35X1GA.patch b/target/linux/mediatek/patches-5.10/340-mtd-spinand-Add-support-for-the-Fidelix-FM35X1GA.patch new file mode 100644 index 0000000000..69a9297e1f --- /dev/null +++ b/target/linux/mediatek/patches-5.10/340-mtd-spinand-Add-support-for-the-Fidelix-FM35X1GA.patch @@ -0,0 +1,122 @@ +From ea0df4552efcdcc2806fe6eba0540b5f719d80b6 Mon Sep 17 00:00:00 2001 +From: Davide Fioravanti +Date: Fri, 8 Jan 2021 15:35:24 +0100 +Subject: [PATCH 1/1] mtd: spinand: Add support for the Fidelix FM35X1GA + +Datasheet: http://www.hobos.com.cn/upload/datasheet/DS35X1GAXXX_100_rev00.pdf + +Signed-off-by: Davide Fioravanti +--- + drivers/mtd/nand/spi/Makefile | 2 +- + drivers/mtd/nand/spi/core.c | 1 + + drivers/mtd/nand/spi/fidelix.c | 80 ++++++++++++++++++++++++++++++++++ + include/linux/mtd/spinand.h | 1 + + 4 files changed, 83 insertions(+), 1 deletion(-) + create mode 100644 drivers/mtd/nand/spi/fidelix.c + +--- a/drivers/mtd/nand/spi/Makefile ++++ b/drivers/mtd/nand/spi/Makefile +@@ -1,3 +1,3 @@ + # SPDX-License-Identifier: GPL-2.0 +-spinand-objs := core.o gigadevice.o macronix.o micron.o paragon.o toshiba.o winbond.o ++spinand-objs := core.o fidelix.o gigadevice.o macronix.o micron.o paragon.o toshiba.o winbond.o + obj-$(CONFIG_MTD_SPI_NAND) += spinand.o +--- a/drivers/mtd/nand/spi/core.c ++++ b/drivers/mtd/nand/spi/core.c +@@ -755,6 +755,7 @@ static const struct nand_ops spinand_ops + }; + + static const struct spinand_manufacturer *spinand_manufacturers[] = { ++ &fidelix_spinand_manufacturer, + &gigadevice_spinand_manufacturer, + ¯onix_spinand_manufacturer, + µn_spinand_manufacturer, +--- /dev/null ++++ b/drivers/mtd/nand/spi/fidelix.c +@@ -0,0 +1,76 @@ ++// SPDX-License-Identifier: GPL-2.0 ++/* ++ * Copyright (c) 2020 Davide Fioravanti ++ */ ++ ++#include ++#include ++#include ++ ++#define SPINAND_MFR_FIDELIX 0xE5 ++#define FIDELIX_ECCSR_MASK 0x0F ++ ++static SPINAND_OP_VARIANTS(read_cache_variants, ++ SPINAND_PAGE_READ_FROM_CACHE_X4_OP(0, 1, NULL, 0), ++ SPINAND_PAGE_READ_FROM_CACHE_OP(true, 0, 1, NULL, 0), ++ SPINAND_PAGE_READ_FROM_CACHE_OP(false, 0, 1, NULL, 0)); ++ ++static SPINAND_OP_VARIANTS(write_cache_variants, ++ SPINAND_PROG_LOAD_X4(true, 0, NULL, 0), ++ SPINAND_PROG_LOAD(true, 0, NULL, 0)); ++ ++static SPINAND_OP_VARIANTS(update_cache_variants, ++ SPINAND_PROG_LOAD_X4(false, 0, NULL, 0), ++ SPINAND_PROG_LOAD(false, 0, NULL, 0)); ++ ++static int fm35x1ga_ooblayout_ecc(struct mtd_info *mtd, int section, ++ struct mtd_oob_region *region) ++{ ++ if (section > 3) ++ return -ERANGE; ++ ++ region->offset = (16 * section) + 8; ++ region->length = 8; ++ ++ return 0; ++} ++ ++static int fm35x1ga_ooblayout_free(struct mtd_info *mtd, int section, ++ struct mtd_oob_region *region) ++{ ++ if (section > 3) ++ return -ERANGE; ++ ++ region->offset = (16 * section) + 2; ++ region->length = 6; ++ ++ return 0; ++} ++ ++static const struct mtd_ooblayout_ops fm35x1ga_ooblayout = { ++ .ecc = fm35x1ga_ooblayout_ecc, ++ .free = fm35x1ga_ooblayout_free, ++}; ++ ++static const struct spinand_info fidelix_spinand_table[] = { ++ SPINAND_INFO("FM35X1GA", ++ SPINAND_ID(SPINAND_READID_METHOD_OPCODE_DUMMY, 0x71), ++ NAND_MEMORG(1, 2048, 64, 64, 1024, 20, 1, 1, 1), ++ NAND_ECCREQ(4, 512), ++ SPINAND_INFO_OP_VARIANTS(&read_cache_variants, ++ &write_cache_variants, ++ &update_cache_variants), ++ SPINAND_HAS_QE_BIT, ++ SPINAND_ECCINFO(&fm35x1ga_ooblayout, NULL)), ++}; ++ ++static const struct spinand_manufacturer_ops fidelix_spinand_manuf_ops = { ++}; ++ ++const struct spinand_manufacturer fidelix_spinand_manufacturer = { ++ .id = SPINAND_MFR_FIDELIX, ++ .name = "Fidelix", ++ .chips = fidelix_spinand_table, ++ .nchips = ARRAY_SIZE(fidelix_spinand_table), ++ .ops = &fidelix_spinand_manuf_ops, ++}; +--- a/include/linux/mtd/spinand.h ++++ b/include/linux/mtd/spinand.h +@@ -238,6 +238,7 @@ struct spinand_manufacturer { + }; + + /* SPI NAND manufacturers */ ++extern const struct spinand_manufacturer fidelix_spinand_manufacturer; + extern const struct spinand_manufacturer gigadevice_spinand_manufacturer; + extern const struct spinand_manufacturer macronix_spinand_manufacturer; + extern const struct spinand_manufacturer micron_spinand_manufacturer;