From: David Bauer Date: Fri, 20 Aug 2021 11:23:42 +0000 (+0200) Subject: ramips: add support for Ubiquiti USW-Flex X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a9839697896c4fdf8c44a06bbce466ce52493069;p=openwrt%2Fstaging%2Fjow.git ramips: add support for Ubiquiti USW-Flex Hardware -------- MediaTek MT7621AT 16M SPI-NOR Macronix MX25L12835FMI Microchip PD69104B1 4-Channel PoE-PSE controller TI TPS2373 PoE-PD controller PoE-Controller -------------- By default, the PoE outputs do not work with OpenWrt. To make them output power, install the "poemgr" package from the packages feed. This package can control the PD69104B1 PSE controller. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt" via SSH. 2. Add the uboot-envtools configuration file /etc/fw_env.config with the following content $ echo "/dev/mtd1 0x0 0x1000 0x10000 1" > /etc/fw_env.config 3. Update the bootloader environment. $ fw_setenv boot_openwrt "fdt addr \$(fdtcontroladdr); fdt rm /signature; bootubnt" $ fw_setenv bootcmd "run boot_openwrt" 4. Transfer the OpenWrt sysupgrade image to the device using SCP. 5. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 6. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock4 7. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock6 $ dd if=openwrt.bin of=/dev/mtdblock7 8. Reboot the device. It should boot into OpenWrt. Restore to UniFi ---------------- To restore the vendor firmware, follow the Ubiquiti UniFi TFTP recovery guide for access points. The process is the same for the Flex switch. Signed-off-by: David Bauer --- diff --git a/target/linux/ramips/dts/mt7621_ubnt_usw-flex.dts b/target/linux/ramips/dts/mt7621_ubnt_usw-flex.dts new file mode 100644 index 0000000000..de5491bf1b --- /dev/null +++ b/target/linux/ramips/dts/mt7621_ubnt_usw-flex.dts @@ -0,0 +1,172 @@ +#include "mt7621.dtsi" + +#include +#include + +/ { + model = "Ubiquiti UniFi Switch Flex"; + compatible = "ubnt,usw-flex", "mediatek,mt7621-soc"; + + aliases { + led-boot = &led_white; + led-failsafe = &led_white; + led-running = &led_blue; + led-upgrade = &led_blue; + label-mac-device = &gmac0; + }; + + chosen { + bootargs-override = "console=ttyS0,115200"; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + led_blue: status_blue { + label = "blue:status"; + gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; + }; + + led_white: status_white { + label = "white:status"; + gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; + }; + }; + + i2c-gpio { + compatible = "i2c-gpio"; + + sda-gpios = <&gpio 3 GPIO_ACTIVE_HIGH>; + scl-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; + + i2c-gpio,delay-us = <50>; + + /* Microsemi PD69104B1 PSE controller */ + }; +}; + +&gmac0 { + nvmem-cells = <&macaddr_eeprom>; + nvmem-cell-names = "mac-address"; + label = "dsa"; +}; + +&switch0 { + ports { + port@0 { + status = "okay"; + label = "lan1"; + }; + + port@1 { + status = "okay"; + label = "lan2"; + }; + + port@2 { + status = "okay"; + label = "lan3"; + }; + + port@3 { + status = "okay"; + label = "lan4"; + }; + + port@4 { + status = "okay"; + label = "lan5"; + }; + }; +}; + +&state_default { + gpio { + groups = "i2c", "uart2", "uart3", "jtag"; + function = "gpio"; + }; +}; + +&spi0 { + status = "okay"; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <30000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x60000>; + read-only; + }; + + partition@60000 { + label = "u-boot-env"; + reg = <0x60000 0x10000>; + }; + + partition@70000 { + label = "factory"; + reg = <0x70000 0x10000>; + read-only; + }; + + part_eeprom: partition@80000 { + compatible = "nvmem-cells"; + + #address-cells = <1>; + #size-cells = <1>; + + label = "eeprom"; + reg = <0x80000 0x10000>; + read-only; + + macaddr_eeprom: macaddr@0 { + reg = <0x0 0x6>; + }; + }; + + partition@90000 { + label = "bs"; + reg = <0x90000 0x10000>; + }; + + partition@a0000 { + label = "cfg"; + reg = <0xa0000 0x100000>; + read-only; + }; + + partition@1a0000 { + compatible = "denx,fit"; + label = "firmware"; + reg = <0x1a0000 0x730000>; + }; + + partition@8d0000 { + label = "kernel1"; + reg = <0x8d0000 0x730000>; + }; + }; + }; +}; + +&xhci { + status = "disabled"; +}; diff --git a/target/linux/ramips/image/mt7621.mk b/target/linux/ramips/image/mt7621.mk index d28aa96224..68993a02fb 100644 --- a/target/linux/ramips/image/mt7621.mk +++ b/target/linux/ramips/image/mt7621.mk @@ -1408,6 +1408,16 @@ define Device/ubnt_unifi-nanohd endef TARGET_DEVICES += ubnt_unifi-nanohd +define Device/ubnt_usw-flex + $(Device/dsa-migration) + DEVICE_VENDOR := Ubiquiti + DEVICE_MODEL := UniFi Switch Flex + DEVICE_DTS_CONFIG := config@1 + KERNEL := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb + IMAGE_SIZE := 7360k +endef +TARGET_DEVICES += ubnt_usw-flex + define Device/unielec_u7621-01-16m $(Device/dsa-migration) $(Device/uimage-lzma-loader) diff --git a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network index 16148547f7..47f978baf8 100644 --- a/target/linux/ramips/mt7621/base-files/etc/board.d/02_network +++ b/target/linux/ramips/mt7621/base-files/etc/board.d/02_network @@ -67,6 +67,9 @@ ramips_setup_interfaces() ubnt,edgerouter-x-sfp) ucidef_set_interfaces_lan_wan "eth1 eth2 eth3 eth4 eth5" "eth0" ;; + ubnt,usw-flex) + ucidef_set_interface_lan "lan1 lan2 lan3 lan4 lan5" + ;; zyxel,nr7101) ucidef_set_interfaces_lan_wan "lan" "wan" ;;