From: Sander Vanheule <sander@svanheule.net>
Date: Sat, 20 Nov 2021 19:11:34 +0000 (+0100)
Subject: realtek: add RTL8231 chip detection
X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a93dfff10e067c152d4872719ec7837fcd8c94a3;p=openwrt%2Fstaging%2Fneocturne.git

realtek: add RTL8231 chip detection

When initialising the driver, check if the RTL8231 chip is actually
present at the specified address. If the READY_CODE value does not match
the expected value, return -ENXIO to fail probing.

This should help users to figure out which address an RTL8231 is
configured to use, if measuring pull-up/-down resistors is not an
option.

On an unsuccesful probe, the driver will log:
    [    0.795364] Probing RTL8231 GPIOs
    [    0.798978] rtl8231_init called, MDIO bus ID: 30
    [    0.804194] rtl8231-gpio rtl8231-gpio: no device found at bus address 30

When a device is found, only the first two lines will be logged:
    [    0.453698] Probing RTL8231 GPIOs
    [    0.457312] rtl8231_init called, MDIO bus ID: 31

Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
---

diff --git a/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c b/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c
index d7643083da..7a1d6aa136 100644
--- a/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c
+++ b/target/linux/realtek/files-5.10/drivers/gpio/gpio-rtl8231.c
@@ -8,6 +8,9 @@
 
 /* RTL8231 registers for LED control */
 #define RTL8231_LED_FUNC0			0x0000
+#define RTL8231_LED_FUNC1			0x0001
+#define RTL8231_READY_MASK			0x03f0
+#define RTL8231_READY_VALUE			0x0370
 #define RTL8231_GPIO_PIN_SEL(gpio)		((0x0002) + ((gpio) >> 4))
 #define RTL8231_GPIO_DIR(gpio)			((0x0005) + ((gpio) >> 4))
 #define RTL8231_GPIO_DATA(gpio)			((0x001C) + ((gpio) >> 4))
@@ -238,6 +241,8 @@ void rtl8231_gpio_set(struct gpio_chip *gc, unsigned int offset, int value)
 
 int rtl8231_init(struct rtl8231_gpios *gpios)
 {
+	u32 ret;
+
 	pr_info("%s called, MDIO bus ID: %d\n", __func__, gpios->smi_bus_id);
 
 	gpios->reg_cached = 0;
@@ -251,6 +256,10 @@ int rtl8231_init(struct rtl8231_gpios *gpios)
 		sw_w32_mask(3, 1, RTL838X_DMY_REG5);
 	}
 
+	ret = rtl8231_read(gpios, RTL8231_LED_FUNC1);
+	if ((ret & 0x80000000) || ((ret & RTL8231_READY_MASK) != RTL8231_READY_VALUE))
+		return -ENXIO;
+
 	/* Select GPIO functionality and force input direction for pins 0-36 */
 	rtl8231_write(gpios, RTL8231_GPIO_PIN_SEL(0), 0xffff);
 	rtl8231_write(gpios, RTL8231_GPIO_DIR(0), 0xffff);
@@ -307,7 +316,11 @@ static int rtl8231_gpio_probe(struct platform_device *pdev)
 		return err;
 	}
 
-	rtl8231_init(gpios);
+	err = rtl8231_init(gpios);
+	if (err) {
+		dev_err(dev, "no device found at bus address %d\n", gpios->smi_bus_id);
+		return err;
+	}
 
 	gpios->dev = dev;
 	gpios->gc.base = -1;