From: Oever González Date: Thu, 24 Jan 2019 03:20:55 +0000 (-0600) Subject: ipq40xx: add support for Linksys EA6350v3 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a873b292840848b67addb5be0c762d292bde33a1;p=openwrt%2Fstaging%2Fjow.git ipq40xx: add support for Linksys EA6350v3 Specifications: SOC: Qualcomm IPQ4018 RAM: 256 MiB Samsung K4B2G1646F-BYK0 FLASH1: MX25L1605D 2 MB FLASH2: Winbond W25N01GV 128Mb ETH: Qualcomm QCA8075 WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Reset LED: Status - Green SERIAL: Header at J19, Beneath DC Power Jack 1-VCC ; 2-TX ; 3-RX; 4-GND; Serial 115200-8-N-1. Tested and working: - USB (requires extra packages) - LAN Ethernet (Correct MAC-address) - WAN Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from Web UI - OpenWRT sysupgrade - LED - Reset Button Need Testing: - WPS button Install via Web UI: - Attach to a LAN port on the router. - Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login - Select the connectivity tab on the left - In the manual update box on the right - Select browse, and browse to openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin - Click update. - Read and accept the warning - The router LED will start blinking. When the router LED goes solid, you can now navigate to 192.168.1.1 to your new OpenWrt installation. Sysupgrade: - Flash the sysupgrade image as usual. Please: try to do a reset everytime you can (doing it with LuCI is easy and can be done in the same step). Recovery (Automatic): - If the device fails to boot after install or upgrade, whilst the unit is turned on: 1 - Wait 15 seconds 2 - Switch Off and Wait 10 seconds 3 - Switch on 4 - Repeat steps 1 to 3, 3 times then go to 5. 5 - U-boot will have now erased the failed update and switched back to the last working firmware - you should be able to access your router on LAN. Recovery (Manual): - The steps for manual recovery are the same as the generic u-boot tftp client method. Back To Stock: - Use the generic recovery using the tftp client method to flash the "civic.img". Also you can strip-and-pad the original image and use the generic "mtd" method by flashing over the "kernel" partition. * Just be careful to flash in the partition that the device is currently booted. Signed-off-by: Ryan Pannell Signed-off-by: Oever González [minor edits, removed second compatible of nand, added dtb entry to 4.19] Signed-off-by: Christian Lamparter --- diff --git a/target/linux/ipq40xx/base-files/etc/board.d/02_network b/target/linux/ipq40xx/base-files/etc/board.d/02_network index d73914c7c1..7b9719848e 100755 --- a/target/linux/ipq40xx/base-files/etc/board.d/02_network +++ b/target/linux/ipq40xx/base-files/etc/board.d/02_network @@ -45,6 +45,15 @@ glinet,gl-b1300) ucidef_add_switch "switch0" \ "0u@eth0" "3:lan" "4:lan" ;; +linksys,ea6350v3) + wan_mac_addr=$(mtd_get_mac_ascii devinfo hw_mac_addr) + lan_mac_addr=$(macaddr_add $(mtd_get_mac_ascii devinfo hw_mac_addr) +1) + ucidef_set_interfaces_lan_wan "eth0" "eth1" + ucidef_add_switch "switch0" \ + "0u@eth0" "1:lan" "2:lan" "3:lan" "4:lan" + ucidef_set_interface_macaddr "wan" "$wan_mac_addr" + ucidef_set_interface_macaddr "lan" "$lan_mac_addr" + ;; openmesh,a42 |\ openmesh,a62) ucidef_set_interfaces_lan_wan "eth1" "eth0" diff --git a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata index 8242fe0eb1..69b6c2591c 100644 --- a/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata +++ b/target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata @@ -115,6 +115,7 @@ case "$FIRMWARE" in case "$board" in 8dev,jalapeno |\ glinet,gl-b1300 |\ + linksys,ea6350v3 |\ qcom,ap-dk01.1-c1) ath10kcal_extract "ART" 4096 12064 ;; @@ -152,6 +153,7 @@ case "$FIRMWARE" in case "$board" in 8dev,jalapeno |\ glinet,gl-b1300 |\ + linksys,ea6350v3 |\ qcom,ap-dk01.1-c1) ath10kcal_extract "ART" 20480 12064 ;; diff --git a/target/linux/ipq40xx/base-files/etc/init.d/zlinksys_recovery b/target/linux/ipq40xx/base-files/etc/init.d/zlinksys_recovery new file mode 100755 index 0000000000..ac6533e3fe --- /dev/null +++ b/target/linux/ipq40xx/base-files/etc/init.d/zlinksys_recovery @@ -0,0 +1,34 @@ +#!/bin/sh /etc/rc.common +# +# This script sets auto_recovery to "yes" and resets the boot counter to 0. +# As a golden rule, this should be the latest script to run at boot. For a +# developer snapshot, it is fine to set auto_recovery here. But for a stable +# release, this script must in fact turn off auto_recovery. +# +# Why? Because the custom sysupgrade script for the device will turn on +# auto_recovery to "yes". And it's the job of this script to set the +# boot boot_count to 0 and then disable auto_recovery, as that condition +# means that the stable release went well. +# +# I have to repeat: this script should be changed for stable releases. + +START=99 +boot() { + . /lib/functions.sh + + case $(board_name) in + linksys,ea6350v3) + # make sure auto_recovery in uboot is always on + IS_AUTO_RECOVERY="$(fw_printenv -n auto_recovery)" + if [ "$IS_AUTO_RECOVERY" != "yes" ] ; then + fw_setenv auto_recovery yes + echo "Linksys EA6350v3: fw_setenv: auto_recovery has been set to yes" + fi + # reset the boot counter + fw_setenv boot_count 0 + mtd resetbc s_env + echo "Linksys EA6350v3: boot counter has been reset" + echo "Linksys EA6350v3: boot_part=$(fw_printenv -n boot_part)" + ;; + esac +} diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh b/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh new file mode 100755 index 0000000000..9772d68f3d --- /dev/null +++ b/target/linux/ipq40xx/base-files/lib/upgrade/linksys.sh @@ -0,0 +1,95 @@ +linksys_get_target_firmware() { + cur_boot_part=$(/usr/sbin/fw_printenv -n boot_part) + target_firmware="" + if [ "$cur_boot_part" = "1" ]; then + # current primary boot - update alt boot + target_firmware="alt_kernel" + fw_setenv boot_part 2 + # In the Linksys EA6350v3, it is enough to set the boot_part as the boot command line is + # bootcmd=if test $boot_part = 1; then run bootpart1; else run bootpart2; fi + # - You probably want to use that if your device's uboot does not eval bootcmd + #fw_setenv bootcmd "run altnandboot" + elif [ "$cur_boot_part" = "2" ]; then + # current alt boot - update primary boot + target_firmware="kernel" + fw_setenv boot_part 1 + #fw_setenv bootcmd "run nandboot" + fi + + # re-enable recovery so we get back if the new firmware is broken + fw_setenv auto_recovery yes + # see /etc/init.d/zlinksys_recovery + + echo "$target_firmware" +} + +linksys_get_root_magic() { + (get_image "$@" | dd skip=786432 bs=4 count=1 | hexdump -v -n 4 -e '1/1 "%02x"') 2>/dev/null +} + +platform_do_upgrade_linksys() { + local magic_long="$(get_magic_long "$1")" + + mkdir -p /var/lock + local part_label="$(linksys_get_target_firmware)" + touch /var/lock/fw_printenv.lock + + if [ ! -n "$part_label" ]; then + echo "cannot find target partition" + exit 1 + fi + + local target_mtd=$(find_mtd_part $part_label) + + [ "$magic_long" = "73797375" ] && { + CI_KERNPART="$part_label" + if [ "$part_label" = "kernel" ]; then + CI_UBIPART="rootfs" + else + CI_UBIPART="alt_rootfs" + fi + + # remove "squashfs" vol (in case we are flashing over a stock image, which is also UBI) + + local mtdnum="$( find_mtd_index "$CI_UBIPART" )" + if [ ! "$mtdnum" ]; then + echo "cannot find ubi mtd partition $CI_UBIPART" + return 1 + fi + + local ubidev="$( nand_find_ubi "$CI_UBIPART" )" + if [ ! "$ubidev" ]; then + ubiattach -m "$mtdnum" + sync + ubidev="$( nand_find_ubi "$CI_UBIPART" )" + fi + + if [ "$ubidev" ]; then + local squash_ubivol="$( nand_find_volume $ubidev squashfs )" + # kill volume + [ "$squash_ubivol" ] && ubirmvol /dev/$ubidev -N squashfs || true + fi + + # complete std upgrade + nand_upgrade_tar "$1" + } + [ "$magic_long" = "27051956" ] && { + # This magic is for a uImage (which is a sysupgrade image) + # check firmwares' rootfs types + local oldroot="$(linksys_get_root_magic $target_mtd)" + local newroot="$(linksys_get_root_magic "$1")" + + if [ "$newroot" = "55424923" -a "$oldroot" = "55424923" ]; then + # we're upgrading from a firmware with UBI to one with UBI + # erase everything to be safe + # - Is that really needed? Won't remove (or comment) the if, because it may be needed in a future device. + #mtd erase $part_label + #get_image "$1" | mtd -n write - $part_label + echo "writing \"$1\" UBI image to \"$part_label\" (UBI)..." + get_image "$1" | mtd write - $part_label + else + echo "writing \"$1\" image to \"$part_label\"" + get_image "$1" | mtd write - $part_label + fi + } +} diff --git a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh index 610f9bbbdb..c5f06ffb3a 100644 --- a/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh +++ b/target/linux/ipq40xx/base-files/lib/upgrade/platform.sh @@ -54,6 +54,9 @@ platform_do_upgrade() { CI_KERNPART="linux" nand_do_upgrade "$1" ;; + linksys,ea6350v3) + platform_do_upgrade_linksys "$ARGV" + ;; openmesh,a42 |\ openmesh,a62) PART_NAME="inactive" diff --git a/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts new file mode 100644 index 0000000000..f27aa68d2a --- /dev/null +++ b/target/linux/ipq40xx/files-4.14/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts @@ -0,0 +1,273 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Linksys EA6350v3"; + compatible = "linksys,ea6350v3", "qcom,ipq4019"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + soc { + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + power: status { + label = "EA6350v3:green:status"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea6350v3"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea6350v3"; +}; + + +&blsp_dma { + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + mux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp1_spi1 { /* BLSP1 QUP1 */ + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, + <&tlmm 59 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + MBIB@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + QSEE@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + CDT@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + APPSBLENV@d0000 { + label = "APPSBLENV"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + APPSBL@e0000 { + label = "APPSBL"; /* uboot */ + reg = <0x000e0000 0x00080000>; + read-only; + }; + ART@160000 { + label = "ART"; + reg = <0x00160000 0x00010000>; + read-only; + }; + u_env@170000 { + label = "u_env"; + reg = <0x00170000 0x00020000>; + }; + s_env@190000 { + label = "s_env"; + reg = <0x00190000 0x00020000>; + }; + devinfo@1b0000 { + label = "devinfo"; + reg = <0x001b0000 0x00010000>; + }; + /* 0x001c0000 - 0x00200000 unused */ + }; + }; + + flash@1 { + status = "okay"; + compatible = "spinand,mt29f", "w25n01gv"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + kernel@0 { + label = "kernel"; + reg = <0x00000000 0x02800000>; + }; + rootfs@300000 { + label = "rootfs"; + reg = <0x00300000 0x02500000>; + }; + alt_kernel@2800000 { + label = "alt_kernel"; + reg = <0x02800000 0x02800000>; + }; + alt_rootfs@2b00000 { + label = "alt_rootfs"; + reg = <0x02b00000 0x02500000>; + }; + sysdiag@5000000 { + label = "sysdiag"; + reg = <0x05000000 0x00100000>; + }; + syscfg@5100000 { + label = "syscfg"; + reg = <0x05100000 0x02F00000>; + }; + /* 0x00000000 - 0x08000000: 128 MiB */ + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts new file mode 100644 index 0000000000..a6f1e1c5b2 --- /dev/null +++ b/target/linux/ipq40xx/files-4.19/arch/arm/boot/dts/qcom-ipq4018-ea6350v3.dts @@ -0,0 +1,273 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT + +#include "qcom-ipq4019.dtsi" +#include +#include +#include + +/ { + model = "Linksys EA6350v3"; + compatible = "linksys,ea6350v3"; + + aliases { + led-boot = &power; + led-failsafe = &power; + led-running = &power; + led-upgrade = &power; + }; + + soc { + mdio@90000 { + status = "okay"; + }; + + ess-psgmii@98000 { + status = "okay"; + }; + + tcsr@1949000 { + compatible = "qcom,tcsr"; + reg = <0x1949000 0x100>; + qcom,wifi_glb_cfg = ; + }; + + tcsr@194b000 { + compatible = "qcom,tcsr"; + reg = <0x194b000 0x100>; + qcom,usb-hsphy-mode-select = ; + }; + + ess_tcsr@1953000 { + compatible = "qcom,tcsr"; + reg = <0x1953000 0x1000>; + qcom,ess-interface-select = ; + }; + + tcsr@1957000 { + compatible = "qcom,tcsr"; + reg = <0x1957000 0x100>; + qcom,wifi_noc_memtype_m0_m2 = ; + }; + + usb2@60f8800 { + status = "okay"; + }; + + usb3@8af8800 { + status = "okay"; + }; + + crypto@8e3a000 { + status = "okay"; + }; + + watchdog@b017000 { + status = "okay"; + }; + + ess-switch@c000000 { + status = "okay"; + }; + + edma@c080000 { + status = "okay"; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + gpios = <&tlmm 63 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + + wps { + label = "wps"; + gpios = <&tlmm 0 GPIO_ACTIVE_LOW>; + linux,code = ; + }; + }; + + leds { + compatible = "gpio-leds"; + + power: status { + label = "EA6350v3:green:status"; + gpios = <&tlmm 2 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&blsp1_uart1 { + pinctrl-0 = <&serial_pins>; + pinctrl-names = "default"; + status = "okay"; +}; + +&cryptobam { + status = "okay"; +}; + +&wifi0 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea6350v3"; +}; + +&wifi1 { + status = "okay"; + qcom,ath10k-calibration-variant = "linksys-ea6350v3"; +}; + + +&blsp_dma { + status = "okay"; +}; + +&tlmm { + serial_pins: serial_pinmux { + mux { + pins = "gpio60", "gpio61"; + function = "blsp_uart0"; + bias-disable; + }; + }; + + spi_0_pins: spi_0_pinmux { + mux { + function = "blsp_spi0"; + pins = "gpio55", "gpio56", "gpio57"; + drive-strength = <12>; + bias-disable; + }; + + mux_cs { + function = "gpio"; + pins = "gpio54", "gpio59"; + drive-strength = <2>; + bias-disable; + output-high; + }; + }; +}; + +&blsp1_spi1 { /* BLSP1 QUP1 */ + pinctrl-0 = <&spi_0_pins>; + pinctrl-names = "default"; + status = "okay"; + cs-gpios = <&tlmm 54 GPIO_ACTIVE_HIGH>, + <&tlmm 59 GPIO_ACTIVE_HIGH>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + SBL1@0 { + label = "SBL1"; + reg = <0x00000000 0x00040000>; + read-only; + }; + MBIB@40000 { + label = "MIBIB"; + reg = <0x00040000 0x00020000>; + read-only; + }; + QSEE@60000 { + label = "QSEE"; + reg = <0x00060000 0x00060000>; + read-only; + }; + CDT@c0000 { + label = "CDT"; + reg = <0x000c0000 0x00010000>; + read-only; + }; + APPSBLENV@d0000 { + label = "APPSBLENV"; + reg = <0x000d0000 0x00010000>; + read-only; + }; + APPSBL@e0000 { + label = "APPSBL"; /* uboot */ + reg = <0x000e0000 0x00080000>; + read-only; + }; + ART@160000 { + label = "ART"; + reg = <0x00160000 0x00010000>; + read-only; + }; + u_env@170000 { + label = "u_env"; + reg = <0x00170000 0x00020000>; + }; + s_env@190000 { + label = "s_env"; + reg = <0x00190000 0x00020000>; + }; + devinfo@1b0000 { + label = "devinfo"; + reg = <0x001b0000 0x00010000>; + }; + /* 0x001c0000 - 0x00200000 unused */ + }; + }; + + flash@1 { + status = "okay"; + compatible = "spi-nand"; + reg = <1>; + spi-max-frequency = <24000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + kernel@0 { + label = "kernel"; + reg = <0x00000000 0x02800000>; + }; + rootfs@300000 { + label = "rootfs"; + reg = <0x00300000 0x02500000>; + }; + alt_kernel@2800000 { + label = "alt_kernel"; + reg = <0x02800000 0x02800000>; + }; + alt_rootfs@2b00000 { + label = "alt_rootfs"; + reg = <0x02b00000 0x02500000>; + }; + sysdiag@5000000 { + label = "sysdiag"; + reg = <0x05000000 0x00100000>; + }; + syscfg@5100000 { + label = "syscfg"; + reg = <0x05100000 0x02F00000>; + }; + /* 0x00000000 - 0x08000000: 128 MiB */ + }; + }; +}; + +&usb3_ss_phy { + status = "okay"; +}; + +&usb3_hs_phy { + status = "okay"; +}; + +&usb2_hs_phy { + status = "okay"; +}; diff --git a/target/linux/ipq40xx/image/Makefile b/target/linux/ipq40xx/image/Makefile index 629a5ef48c..a670380ab3 100644 --- a/target/linux/ipq40xx/image/Makefile +++ b/target/linux/ipq40xx/image/Makefile @@ -26,6 +26,12 @@ define Device/FitImageLzma KERNEL_NAME := Image endef +define Device/FitzImage + KERNEL_SUFFIX := -fit-zImage.itb + KERNEL = kernel-bin | fit none $$(DTS_DIR)/$$(DEVICE_DTS).dtb + KERNEL_NAME := zImage +endef + define Device/UbiFit KERNEL_IN_UBI := 1 IMAGES := nand-factory.ubi nand-sysupgrade.bin @@ -131,6 +137,41 @@ define Device/glinet_gl-b1300 endef TARGET_DEVICES += glinet_gl-b1300 +define Device/linksys_ea6350v3 + # The Linksys EA6350v3 has a uboot bootloader that does not + # support either booting lzma kernel images nor booting UBI + # partitions. This uboot, however, supports raw kernel images and + # gzipped images. + # + # As for the time of writing this, the device will boot the kernel + # from a fixed address with a fixed length of 3MiB. Also, the + # device has a hard-coded kernel command line that requieres the + # rootfs and alt_rootfs to be in mtd11 and mtd13 respectively. + # Oh... and the kernel partition overlaps with the rootfs + # partition (the same for alt_kernel and alt_rootfs). + # + # If you are planing re-partitioning the device, you may want to + # keep those details in mind: + # 1. The kernel adresses you should honor are 0x00000000 and + # 0x02800000 respectively. + # 2. The kernel size (plus the dtb) cannot exceed 3.00MiB in size. + # 3. You can use 'zImage', but not a raw 'Image' packed with lzma. + # 4. The kernel command line from uboot is harcoded to boot with + # rootfs either in mtd11 or mtd13. + $(call Device/FitzImage) + DEVICE_TITLE := Linksys EA6350v3 + DEVICE_DTS := qcom-ipq4018-ea6350v3 + BLOCKSIZE := 128k + PAGESIZE := 2048 + KERNEL_SIZE := 3145728 + IMAGE_SIZE := 38797312 + UBINIZE_OPTS := -E 5 + IMAGES := factory.bin sysupgrade.bin + IMAGE/factory.bin := append-kernel | append-uImage-fakehdr filesystem | pad-to $$$${KERNEL_SIZE} | append-ubi | linksys-image type=EA6350v3 + DEVICE_PACKAGES := ipq-wifi-linksys_ea6350v3 uboot-envtools +endef +TARGET_DEVICES += linksys_ea6350v3 + define Device/meraki_mr33 $(call Device/FitImage) DEVICE_DTS := qcom-ipq4029-mr33 diff --git a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch index 46c34038d6..e0619a64dd 100644 --- a/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.14/901-arm-boot-add-dts-files.patch @@ -10,11 +10,12 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -697,7 +697,21 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -697,7 +697,22 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ + qcom-ipq4018-a42.dtb \ ++ qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ + qcom-ipq4018-ex6100v2.dtb \ + qcom-ipq4018-ex6150v2.dtb \ diff --git a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch index d6d551cf16..d0f892bc48 100644 --- a/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch +++ b/target/linux/ipq40xx/patches-4.19/901-arm-boot-add-dts-files.patch @@ -10,11 +10,12 @@ Signed-off-by: John Crispin --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile -@@ -785,11 +785,24 @@ dtb-$(CONFIG_ARCH_QCOM) += \ +@@ -785,11 +785,25 @@ dtb-$(CONFIG_ARCH_QCOM) += \ qcom-apq8074-dragonboard.dtb \ qcom-apq8084-ifc6540.dtb \ qcom-apq8084-mtp.dtb \ + qcom-ipq4018-a42.dtb \ ++ qcom-ipq4018-ea6350v3.dtb \ + qcom-ipq4018-eap1300.dtb \ + qcom-ipq4018-ex6100v2.dtb \ + qcom-ipq4018-ex6150v2.dtb \