From: Gabor Juhos Date: Thu, 11 Oct 2007 09:11:56 +0000 (+0000) Subject: switch to 2.6.23 X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a72e25de51090dc2a161ecb7e7f73e1e9d5f9932;p=openwrt%2Fstaging%2Fkaloz.git switch to 2.6.23 SVN-Revision: 9260 --- diff --git a/target/linux/adm5120/Makefile b/target/linux/adm5120/Makefile index 34c3b804a7..ed9dce2c41 100644 --- a/target/linux/adm5120/Makefile +++ b/target/linux/adm5120/Makefile @@ -8,7 +8,7 @@ include $(TOPDIR)/rules.mk BOARD:=adm5120 -LINUX_VERSION:=2.6.22.4 +LINUX_VERSION:=2.6.23 FEATURES:=squashfs jffs2 tgz broken include $(INCLUDE_DIR)/target.mk diff --git a/target/linux/adm5120/files/arch/mips/pci/pci-adm5120.c b/target/linux/adm5120/files/arch/mips/pci/pci-adm5120.c index 0113234398..5aa5a633d5 100644 --- a/target/linux/adm5120/files/arch/mips/pci/pci-adm5120.c +++ b/target/linux/adm5120/files/arch/mips/pci/pci-adm5120.c @@ -199,7 +199,7 @@ void __init adm5120_pci_set_irq_map(unsigned int nr_irqs, adm5120_pci_irq_map = map; } -int __init pcibios_map_irq(struct pci_dev *dev, u8 slot, u8 pin) +int __init pcibios_map_irq(const struct pci_dev *dev, u8 slot, u8 pin) { int irq = -1; int i; diff --git a/target/linux/adm5120/files/drivers/leds/leds-adm5120.c b/target/linux/adm5120/files/drivers/leds/leds-adm5120.c index 06189371d7..f3a9b0154f 100644 --- a/target/linux/adm5120/files/drivers/leds/leds-adm5120.c +++ b/target/linux/adm5120/files/drivers/leds/leds-adm5120.c @@ -29,13 +29,13 @@ #include #include -#include +#include +#include #include -#include #include -#include +#include #define NUM_LEDS_MAX 23 @@ -43,12 +43,13 @@ struct mach_data { unsigned long machtype; - unsigned count; - struct gpio_led_platform_data *data; + unsigned nr_leds; + struct gpio_led *leds; }; struct adm5120_leddev { struct platform_device pdev; + struct gpio_led led; struct gpio_led_platform_data pdata; }; @@ -56,19 +57,17 @@ static int led_count = 0; static struct adm5120_leddev *led_devs[NUM_LEDS_MAX]; #define LED_ARRAY(n) \ -static struct gpio_led_platform_data \ -n ## _leds [] __initdata = +static struct gpio_led n ## _leds [] __initdata = -#define LED_DATA(n,t,g,off,on) { \ +#define LED_DATA(n,t,g,al) { \ .name = (n), \ - .trigger = (t), \ + .default_trigger = (t), \ .gpio = (g), \ - .value_off = (off), \ - .value_on = (on) \ + .active_low = (al) \ } -#define LED_STD(g,n,t) LED_DATA((n),(t),(g), 0, 1) -#define LED_INV(g,n,t) LED_DATA((n),(t),(g), 1, 0) +#define LED_STD(g,n,t) LED_DATA((n),(t),(g), 0) +#define LED_INV(g,n,t) LED_DATA((n),(t),(g), 1) /* * Compex boards @@ -218,8 +217,8 @@ LED_ARRAY(generic) { #define MACH_DATA(m, n) { \ .machtype = (m), \ - .count = ARRAY_SIZE(n ## _leds), \ - .data = n ## _leds \ + .nr_leds = ARRAY_SIZE(n ## _leds), \ + .leds = n ## _leds \ } static struct mach_data machines[] __initdata = { @@ -250,7 +249,7 @@ static struct mach_data machines[] __initdata = { }; static struct adm5120_leddev * __init -create_leddev(struct gpio_led_platform_data *data) +create_leddev(int id, struct gpio_led *led) { struct adm5120_leddev *p; @@ -258,17 +257,21 @@ create_leddev(struct gpio_led_platform_data *data) if (p == NULL) return NULL; - memcpy(&p->pdata, data, sizeof(p->pdata)); + memcpy(&p->led, led, sizeof(p->led)); + p->pdev.name = "leds-gpio"; + p->pdev.id = id; p->pdev.dev.platform_data = &p->pdata; + p->pdata.num_leds=1; + p->pdata.leds = &p->led; return p; } static void -destroy_leddev(struct adm5120_leddev *led) +destroy_leddev(struct adm5120_leddev *leddev) { - if (led) - kfree(led); + if (leddev) + kfree(leddev); } static struct mach_data * __init @@ -311,23 +314,21 @@ adm5120_leds_init(void) goto err; } - for (i=0; i < mach->count; i++) { - led_devs[i] = create_leddev(&mach->data[i]); + for (i=0; i < mach->nr_leds; i++) { + led_devs[i] = create_leddev(i, &mach->leds[i]); if (led_devs[i] == NULL) { ret = -ENOMEM; goto err_destroy; } - led_devs[i]->pdev.name = "gpio-led"; - led_devs[i]->pdev.id = i; } - for (i=0; i < mach->count; i++) { + for (i=0; i < mach->nr_leds; i++) { ret = platform_device_register(&led_devs[i]->pdev); if (ret) goto err_unregister; } - led_count = mach->count; + led_count = mach->nr_leds; return 0; err_unregister: diff --git a/target/linux/adm5120/files/drivers/leds/leds-gpio.c b/target/linux/adm5120/files/drivers/leds/leds-gpio.c deleted file mode 100755 index b1a1f1ce9a..0000000000 --- a/target/linux/adm5120/files/drivers/leds/leds-gpio.c +++ /dev/null @@ -1,212 +0,0 @@ -/* - * $Id$ - * - * Driver for LEDs connected to GPIO lines - * - * Copyright (C) 2007 OpenWrt.org - * Copyright (C) 2007 Gabor Juhos - * - * This file was derived from: - * /drivers/led/leds-s3c24xx.c - * (c) 2006 Simtec Electronics, Ben Dooks - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License - * as published by the Free Software Foundation; either version 2 - * of the License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - * GNU General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the - * Free Software Foundation, Inc., 51 Franklin Street, Fifth Floor, - * Boston, MA 02110-1301, USA. - * - */ - -#include -#include -#include -#include -#include - -#include - -#include -#include - -#define DRV_NAME "gpio-led" -#define DRV_DESC "GPIO LEDs driver" - -struct gpio_led_device { - struct led_classdev cdev; - struct gpio_led_platform_data *pdata; -}; - -static inline struct gpio_led_device *pdev_to_led(struct platform_device *dev) -{ - return platform_get_drvdata(dev); -} - -static inline struct gpio_led_device *class_to_led(struct led_classdev *led_cdev) -{ - return container_of(led_cdev, struct gpio_led_device, cdev); -} - -static void gpio_led_set(struct led_classdev *led_cdev, - enum led_brightness brightness) -{ - struct gpio_led_device *led; - struct gpio_led_platform_data *pdata; - - led = class_to_led(led_cdev); - pdata = led->pdata; - - switch (brightness) { - case LED_FULL: - gpio_direction_output(pdata->gpio, pdata->value_on); - break; - case LED_OFF: - gpio_direction_output(pdata->gpio, pdata->value_off); - break; - default: - gpio_direction_output(pdata->gpio, brightness); - break; - } -} - -static int __devinit gpio_led_probe(struct platform_device *dev) -{ - struct gpio_led_platform_data *pdata; - struct gpio_led_device *led; - int ret; - - pdata = dev->dev.platform_data; - if (pdata == NULL) { - dev_err(&dev->dev, "no platform data, id=%d\n", dev->id); - ret = -EINVAL; - goto err; - } - - if (pdata->name == NULL) { - dev_err(&dev->dev, "no led name specified\n"); - ret = -EINVAL; - goto err; - } - - ret = gpio_request(pdata->gpio, pdata->name); - if (ret) { - dev_err(&dev->dev, "gpio_request failed\n"); - goto err; - } - - led = kzalloc(sizeof(*led), GFP_KERNEL); - if (led == NULL) { - dev_err(&dev->dev, "no memory for device"); - ret = -ENOMEM; - goto err_free_gpio; - } - - platform_set_drvdata(dev, led); - led->pdata = pdata; - led->cdev.name = pdata->name; - led->cdev.brightness_set = gpio_led_set; -#ifdef CONFIG_LEDS_TRIGGERS - led->cdev.default_trigger = pdata->trigger; -#endif - - ret = led_classdev_register(&dev->dev, &led->cdev); - if (ret < 0) { - dev_err(&dev->dev, "led_classdev_register failed"); - goto err_free_led; - } - - return 0; - -err_free_led: - kfree(led); -err_free_gpio: - gpio_free(pdata->gpio); -err: - return ret; -} - -static int __devexit gpio_led_remove(struct platform_device *dev) -{ - struct gpio_led_device *led; - struct gpio_led_platform_data *pdata; - - pdata = dev->dev.platform_data; - - led = pdev_to_led(dev); - led_classdev_unregister(&led->cdev); - kfree(led); - - gpio_free(pdata->gpio); - - return 0; -} - -#ifdef CONFIG_PM -static int gpio_led_suspend(struct platform_device *dev, - pm_message_t state) -{ - struct gpio_led_device *led; - - led = pdev_to_led(dev); - led_classdev_suspend(&led->cdev); - - return 0; -} - -static int gpio_led_resume(struct platform_device *dev) -{ - struct gpio_led_device *led; - - led = pdev_to_led(dev); - led_classdev_resume(&led->cdev); - - return 0; -} -#endif /* CONFIG_PM */ - -static struct platform_driver gpio_led_driver = { - .probe = gpio_led_probe, - .remove = __devexit_p(gpio_led_remove), -#ifdef CONFIG_PM - .suspend = gpio_led_suspend, - .resume = gpio_led_resume, -#endif - .driver = { - .name = DRV_NAME, - .owner = THIS_MODULE, - }, -}; - -static int __init gpio_led_init(void) -{ - int ret; - - ret = platform_driver_register(&gpio_led_driver); - if (ret) - printk(KERN_ALERT DRV_DESC " register failed\n"); - else - printk(KERN_INFO DRV_DESC " registered\n"); - - return ret; -} - -static void __exit gpio_led_exit(void) -{ - platform_driver_unregister(&gpio_led_driver); -} - -module_init(gpio_led_init); -module_exit(gpio_led_exit); - -MODULE_AUTHOR("Gabor Juhos "); -MODULE_DESCRIPTION(DRV_DESC); -MODULE_LICENSE("GPL"); diff --git a/target/linux/adm5120/patches-2.6.22/001-adm5120.patch b/target/linux/adm5120/patches-2.6.22/001-adm5120.patch deleted file mode 100644 index b17ba4cff5..0000000000 --- a/target/linux/adm5120/patches-2.6.22/001-adm5120.patch +++ /dev/null @@ -1,115 +0,0 @@ -Index: linux-2.6.22.1/arch/mips/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/arch/mips/Kconfig -+++ linux-2.6.22.1/arch/mips/Kconfig -@@ -15,6 +15,18 @@ choice - prompt "System type" - default SGI_IP22 - -+config MIPS_ADM5120 -+ bool "Support for ADM5120 SoC" -+ select SYS_HAS_CPU_MIPS32_R1 -+ select SYS_HAS_EARLY_PRINTK -+ select DMA_NONCOHERENT -+ select HW_HAS_PCI -+ select IRQ_CPU -+ select SYS_SUPPORTS_LITTLE_ENDIAN -+ select SYS_SUPPORTS_BIG_ENDIAN -+ select SYS_SUPPORTS_32BIT_KERNEL -+ select GENERIC_GPIO -+ - config MACH_ALCHEMY - bool "Alchemy processor based machines" - -@@ -658,6 +670,7 @@ config TOSHIBA_RBTX4938 - - endchoice - -+source "arch/mips/adm5120/Kconfig" - source "arch/mips/au1000/Kconfig" - source "arch/mips/ddb5xxx/Kconfig" - source "arch/mips/gt64120/ev64120/Kconfig" -Index: linux-2.6.22.1/arch/mips/Makefile -=================================================================== ---- linux-2.6.22.1.orig/arch/mips/Makefile -+++ linux-2.6.22.1/arch/mips/Makefile -@@ -165,6 +165,16 @@ cflags-$(CONFIG_MACH_JAZZ) += -Iinclude/ - load-$(CONFIG_MACH_JAZZ) += 0xffffffff80080000 - - # -+# ADMtek 5120 -+# -+ -+libs-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/prom/ -+core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/ -+core-$(CONFIG_MIPS_ADM5120) += arch/mips/adm5120/boards/ -+cflags-$(CONFIG_MIPS_ADM5120) += -Iinclude/asm-mips/mach-adm5120 -+load-$(CONFIG_MIPS_ADM5120) += 0xffffffff80001000 -+ -+# - # Common Alchemy Au1x00 stuff - # - core-$(CONFIG_SOC_AU1X00) += arch/mips/au1000/common/ -Index: linux-2.6.22.1/include/asm-mips/bootinfo.h -=================================================================== ---- linux-2.6.22.1.orig/include/asm-mips/bootinfo.h -+++ linux-2.6.22.1/include/asm-mips/bootinfo.h -@@ -213,6 +213,58 @@ - #define MACH_GROUP_NEC_EMMA2RH 25 /* NEC EMMA2RH (was 23) */ - #define MACH_NEC_MARKEINS 0 /* NEC EMMA2RH Mark-eins */ - -+/* -+ * Valid machtype for group ADMtek ADM5120 -+ */ -+#define MACH_GROUP_ADM5120 26 -+#define MACH_ADM5120_GENERIC 0 /* Generic board */ -+#define MACH_ADM5120_WP54G_WRT 1 /* Compex WP54G-WRT */ -+#define MACH_ADM5120_WP54G 2 /* Compex WP54G */ -+#define MACH_ADM5120_WP54AG 3 /* Compex WP54AG */ -+#define MACH_ADM5120_WPP54G 4 /* Compex WPP54G */ -+#define MACH_ADM5120_WPP54AG 5 /* Compex WPP54AG */ -+#define MACH_ADM5120_NP28G 6 /* Compex NP28G */ -+#define MACH_ADM5120_NP28GHS 7 /* Compex NP28G HotSpot */ -+#define MACH_ADM5120_NP27G 8 /* Compex NP27G */ -+#define MACH_ADM5120_WP54Gv1C 9 /* Compex WP54G version 1C */ -+#define MACH_ADM5120_RB_111 10 /* Mikrotik RouterBOARD 111 */ -+#define MACH_ADM5120_RB_112 11 /* Mikrotik RouterBOARD 112 */ -+#define MACH_ADM5120_RB_133 12 /* Mikrotik RouterBOARD 133 */ -+#define MACH_ADM5120_RB_133C 13 /* Mikrotik RouterBOARD 133c */ -+#define MACH_ADM5120_RB_150 14 /* Mikrotik RouterBOARD 150 */ -+#define MACH_ADM5120_RB_153 15 /* Mikrotik RouterBOARD 153 */ -+#define MACH_ADM5120_HS100 16 /* ZyXEL HomeSafe 100/100W */ -+#define MACH_ADM5120_P334 17 /* ZyXEL Prestige 334 */ -+#define MACH_ADM5120_P334U 18 /* ZyXEL Prestige 334U */ -+#define MACH_ADM5120_P334W 19 /* ZyXEL Prestige 334W */ -+#define MACH_ADM5120_P334WH 20 /* ZyXEL Prestige 334WH */ -+#define MACH_ADM5120_P334WHD 21 /* ZyXEL Prestige 334WHD */ -+#define MACH_ADM5120_P334WT 22 /* ZyXEL Prestige 334WT */ -+#define MACH_ADM5120_P335 23 /* ZyXEL Prestige 335/335WT */ -+#define MACH_ADM5120_P335PLUS 24 /* ZyXEL Prestige 335Plus */ -+#define MACH_ADM5120_P335U 25 /* ZyXEL Prestige 335U */ -+#define MACH_ADM5120_ES2108 26 /* ZyXEL Ethernet Switch 2108 */ -+#define MACH_ADM5120_ES2108F 27 /* ZyXEL Ethernet Switch 2108-F */ -+#define MACH_ADM5120_ES2108G 28 /* ZyXEL Ethernet Switch 2108-G */ -+#define MACH_ADM5120_ES2108LC 29 /* ZyXEL Ethernet Switch 2108-LC */ -+#define MACH_ADM5120_ES2108PWR 30 /* ZyXEL Ethernet Switch 2108-PWR */ -+#define MACH_ADM5120_ES2024A 31 /* ZyXEL Ethernet Switch 2024A */ -+#define MACH_ADM5120_ES2024PWR 32 /* ZyXEL Ethernet Switch 2024PWR */ -+#define MACH_ADM5120_CAS630 33 /* Cellvision CAS-630/630W */ -+#define MACH_ADM5120_CAS670 34 /* Cellvision CAS-670/670W */ -+#define MACH_ADM5120_CAS700 36 /* Cellvision CAS-700/700W */ -+#define MACH_ADM5120_CAS771 37 /* Cellvision CAS-771/771W */ -+#define MACH_ADM5120_CAS790 38 /* Cellvision CAS-790 */ -+#define MACH_ADM5120_CAS861 39 /* Cellvision CAS-861/861W */ -+#define MACH_ADM5120_NFS101U 40 /* Cellvision NFS-101U/101WU */ -+#define MACH_ADM5120_NFS202U 41 /* Cellvision NFS-202U/202WU */ -+#define MACH_ADM5120_EASY5120PATA 42 /* Infineon EASY 5120P-ATA */ -+#define MACH_ADM5120_EASY5120RT 43 /* Infineon EASY 5120-RT */ -+#define MACH_ADM5120_EASY5120WVOIP 44 /* Infineon EASY 5120-WVoIP */ -+#define MACH_ADM5120_EASY83000 45 /* Infineon EASY-83000 */ -+#define MACH_ADM5120_BR6104K 46 /* Edimax BR-6104K */ -+#define MACH_ADM5120_RB_192 47 /* Mikrotik RouterBOARD 192 */ -+ - #define CL_SIZE COMMAND_LINE_SIZE - - const char *get_system_type(void); diff --git a/target/linux/adm5120/patches-2.6.22/002-adm5120_flash.patch b/target/linux/adm5120/patches-2.6.22/002-adm5120_flash.patch deleted file mode 100644 index e2f21bfc4c..0000000000 --- a/target/linux/adm5120/patches-2.6.22/002-adm5120_flash.patch +++ /dev/null @@ -1,26 +0,0 @@ -Index: linux-2.6.22.1/drivers/mtd/maps/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/maps/Kconfig -+++ linux-2.6.22.1/drivers/mtd/maps/Kconfig -@@ -620,5 +620,9 @@ config MTD_PLATRAM - - This selection automatically selects the map_ram driver. - -+config MTD_ADM5120 -+ tristate "Map driver for ADM5120 based boards" -+ depends on MIPS_ADM5120 -+ - endmenu - -Index: linux-2.6.22.1/drivers/mtd/maps/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/maps/Makefile -+++ linux-2.6.22.1/drivers/mtd/maps/Makefile -@@ -47,6 +47,7 @@ obj-$(CONFIG_MTD_OCELOT) += ocelot.o - obj-$(CONFIG_MTD_SOLUTIONENGINE)+= solutionengine.o - obj-$(CONFIG_MTD_PCI) += pci.o - obj-$(CONFIG_MTD_ALCHEMY) += alchemy-flash.o -+obj-$(CONFIG_MTD_ADM5120) += adm5120-flash.o - obj-$(CONFIG_MTD_LASAT) += lasat.o - obj-$(CONFIG_MTD_AUTCPU12) += autcpu12-nvram.o - obj-$(CONFIG_MTD_EDB7312) += edb7312.o diff --git a/target/linux/adm5120/patches-2.6.22/003-adm5120_switch.patch b/target/linux/adm5120/patches-2.6.22/003-adm5120_switch.patch deleted file mode 100644 index ff8a9bbc29..0000000000 --- a/target/linux/adm5120/patches-2.6.22/003-adm5120_switch.patch +++ /dev/null @@ -1,27 +0,0 @@ -Index: linux-2.6.22.1/drivers/net/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/net/Kconfig -+++ linux-2.6.22.1/drivers/net/Kconfig -@@ -574,6 +574,10 @@ config MIPS_AU1X00_ENET - If you have an Alchemy Semi AU1X00 based system - say Y. Otherwise, say N. - -+config MIPS_ADM5120_ENET -+ tristate "MIPS ADM5120 Ethernet switch support" -+ depends on NET_ETHERNET && MIPS_ADM5120 -+ - config NET_SB1250_MAC - tristate "SB1250 Ethernet support" - depends on NET_ETHERNET && SIBYTE_SB1xxx_SOC -Index: linux-2.6.22.1/drivers/net/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/net/Makefile -+++ linux-2.6.22.1/drivers/net/Makefile -@@ -165,6 +165,7 @@ obj-$(CONFIG_SC92031) += sc92031.o - # This is also a 82596 and should probably be merged - obj-$(CONFIG_LP486E) += lp486e.o - -+obj-$(CONFIG_MIPS_ADM5120_ENET) += adm5120sw.o - obj-$(CONFIG_ETH16I) += eth16i.o - obj-$(CONFIG_ZORRO8390) += zorro8390.o - obj-$(CONFIG_HPLANCE) += hplance.o 7990.o diff --git a/target/linux/adm5120/patches-2.6.22/004-adm5120_nand.patch b/target/linux/adm5120/patches-2.6.22/004-adm5120_nand.patch deleted file mode 100644 index 5441fef415..0000000000 --- a/target/linux/adm5120/patches-2.6.22/004-adm5120_nand.patch +++ /dev/null @@ -1,33 +0,0 @@ -Index: linux-2.6.22.1/drivers/mtd/nand/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/nand/Kconfig -+++ linux-2.6.22.1/drivers/mtd/nand/Kconfig -@@ -81,6 +81,16 @@ config MTD_NAND_TS7250 - help - Support for NAND flash on Technologic Systems TS-7250 platform. - -+config MTD_NAND_ADM5120 -+ tristate "ADM5120 NAND support" -+ depends on MTD_NAND && MIPS_ADM5120 -+ help -+ This enables the driver for the ADM5120 SoC built-in -+ NAND flash interface. -+ -+ No board specific support is done by this driver, each board -+ must advertise a platform_device for the driver to attach. -+ - config MTD_NAND_IDS - tristate - -Index: linux-2.6.22.1/drivers/mtd/nand/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/nand/Makefile -+++ linux-2.6.22.1/drivers/mtd/nand/Makefile -@@ -10,6 +10,7 @@ obj-$(CONFIG_MTD_NAND_CAFE) += cafe_nan - obj-$(CONFIG_MTD_NAND_SPIA) += spia.o - obj-$(CONFIG_MTD_NAND_AMS_DELTA) += ams-delta.o - obj-$(CONFIG_MTD_NAND_TOTO) += toto.o -+obj-$(CONFIG_MTD_NAND_ADM5120) += adm5120-nand.o - obj-$(CONFIG_MTD_NAND_AUTCPU12) += autcpu12.o - obj-$(CONFIG_MTD_NAND_EDB7312) += edb7312.o - obj-$(CONFIG_MTD_NAND_AU1550) += au1550nd.o diff --git a/target/linux/adm5120/patches-2.6.22/005-adm5120_usb.patch b/target/linux/adm5120/patches-2.6.22/005-adm5120_usb.patch deleted file mode 100644 index 0a74e9103d..0000000000 --- a/target/linux/adm5120/patches-2.6.22/005-adm5120_usb.patch +++ /dev/null @@ -1,35 +0,0 @@ -Index: linux-2.6.22.1/drivers/usb/host/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/usb/host/Kconfig -+++ linux-2.6.22.1/drivers/usb/host/Kconfig -@@ -237,3 +237,6 @@ config USB_SL811_CS - To compile this driver as a module, choose M here: the - module will be called "sl811_cs". - -+config USB_ADM5120_HCD -+ tristate "ADM5120 HCD support (EXPERIMENTAL)" -+ depends on USB && MIPS_ADM5120 && EXPERIMENTAL -Index: linux-2.6.22.1/drivers/usb/host/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/usb/host/Makefile -+++ linux-2.6.22.1/drivers/usb/host/Makefile -@@ -8,6 +8,7 @@ endif - - obj-$(CONFIG_PCI) += pci-quirks.o - -+obj-$(CONFIG_USB_ADM5120_HCD) += adm5120-hcd.o - obj-$(CONFIG_USB_EHCI_HCD) += ehci-hcd.o - obj-$(CONFIG_USB_ISP116X_HCD) += isp116x-hcd.o - obj-$(CONFIG_USB_OHCI_HCD) += ohci-hcd.o -Index: linux-2.6.22.1/drivers/usb/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/usb/Makefile -+++ linux-2.6.22.1/drivers/usb/Makefile -@@ -16,6 +16,7 @@ obj-$(CONFIG_USB_UHCI_HCD) += host/ - obj-$(CONFIG_USB_SL811_HCD) += host/ - obj-$(CONFIG_USB_U132_HCD) += host/ - obj-$(CONFIG_USB_OHCI_AT91) += host/ -+obj-$(CONFIG_USB_ADM5120_HCD) += host/ - - obj-$(CONFIG_USB_ACM) += class/ - obj-$(CONFIG_USB_PRINTER) += class/ diff --git a/target/linux/adm5120/patches-2.6.22/006-adm5120_leds.patch b/target/linux/adm5120/patches-2.6.22/006-adm5120_leds.patch deleted file mode 100644 index bf173bd92c..0000000000 --- a/target/linux/adm5120/patches-2.6.22/006-adm5120_leds.patch +++ /dev/null @@ -1,45 +0,0 @@ -Index: linux-2.6.22.1/drivers/leds/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/leds/Kconfig -+++ linux-2.6.22.1/drivers/leds/Kconfig -@@ -20,6 +20,27 @@ config LEDS_CLASS - - comment "LED drivers" - -+config LEDS_GPIO -+ tristate "LED support for LEDS on GPIO lines" -+ depends on LEDS_CLASS && GENERIC_GPIO -+ help -+ This option enables support for LEDs connected to GPIO lines -+ -+config LEDS_ADM5120 -+ tristate "LED Support for ADM5120 GPIO LEDs" -+ depends on LEDS_GPIO && MIPS_ADM5120 -+ help -+ This option enables support for LEDs connected to GPIO lines -+ on ADM5120 SoC based platforms. -+ -+config LEDS_ADM5120_EXPERIMENTAL -+ bool "Enable ADM5120 LEDs experimental code" -+ depends on LEDS_ADM5120 -+ -+config LEDS_ADM5120_DIAG -+ bool "Enable ADM5120 LEDs diagnostic mode" -+ depends on LEDS_ADM5120 -+ - config LEDS_CORGI - tristate "LED Support for the Sharp SL-C7x0 series" - depends on LEDS_CLASS && PXA_SHARP_C7xx -Index: linux-2.6.22.1/drivers/leds/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/leds/Makefile -+++ linux-2.6.22.1/drivers/leds/Makefile -@@ -5,6 +5,8 @@ obj-$(CONFIG_LEDS_CLASS) += led-class.o - obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o - - # LED Platform Drivers -+obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o -+obj-$(CONFIG_LEDS_ADM5120) += leds-adm5120.o - obj-$(CONFIG_LEDS_CORGI) += leds-corgi.o - obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o - obj-$(CONFIG_LEDS_SPITZ) += leds-spitz.o diff --git a/target/linux/adm5120/patches-2.6.22/007-adm5120_pci.patch b/target/linux/adm5120/patches-2.6.22/007-adm5120_pci.patch deleted file mode 100644 index 79a5a6910a..0000000000 --- a/target/linux/adm5120/patches-2.6.22/007-adm5120_pci.patch +++ /dev/null @@ -1,23 +0,0 @@ -Index: linux-2.6.22.1/arch/mips/pci/Makefile -=================================================================== ---- linux-2.6.22.1.orig/arch/mips/pci/Makefile -+++ linux-2.6.22.1/arch/mips/pci/Makefile -@@ -50,3 +50,4 @@ obj-$(CONFIG_TOSHIBA_RBTX4938) += fixup- - obj-$(CONFIG_VICTOR_MPC30X) += fixup-mpc30x.o - obj-$(CONFIG_ZAO_CAPCELLA) += fixup-capcella.o - obj-$(CONFIG_WR_PPMC) += fixup-wrppmc.o -+obj-$(CONFIG_PCI_ADM5120) += pci-adm5120.o -Index: linux-2.6.22.1/include/linux/pci_ids.h -=================================================================== ---- linux-2.6.22.1.orig/include/linux/pci_ids.h -+++ linux-2.6.22.1/include/linux/pci_ids.h -@@ -1713,6 +1713,9 @@ - #define PCI_VENDOR_ID_ESDGMBH 0x12fe - #define PCI_DEVICE_ID_ESDGMBH_CPCIASIO4 0x0111 - -+#define PCI_VENDOR_ID_ADMTEK 0x1317 -+#define PCI_DEVICE_ID_ADMTEK_ADM5120 0x5120 -+ - #define PCI_VENDOR_ID_SIIG 0x131f - #define PCI_SUBVENDOR_ID_SIIG 0x131f - #define PCI_DEVICE_ID_SIIG_1S_10x_550 0x1000 diff --git a/target/linux/adm5120/patches-2.6.22/008-adm5120_uart.patch b/target/linux/adm5120/patches-2.6.22/008-adm5120_uart.patch deleted file mode 100644 index 7f8451324d..0000000000 --- a/target/linux/adm5120/patches-2.6.22/008-adm5120_uart.patch +++ /dev/null @@ -1,53 +0,0 @@ -Index: linux-2.6.22.1/drivers/serial/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/serial/Makefile -+++ linux-2.6.22.1/drivers/serial/Makefile -@@ -21,6 +21,7 @@ obj-$(CONFIG_SERIAL_8250_EXAR_ST16C554) - obj-$(CONFIG_SERIAL_8250_HUB6) += 8250_hub6.o - obj-$(CONFIG_SERIAL_8250_MCA) += 8250_mca.o - obj-$(CONFIG_SERIAL_8250_AU1X00) += 8250_au1x00.o -+obj-$(CONFIG_SERIAL_ADM5120) += adm5120_uart.o - obj-$(CONFIG_SERIAL_AMBA_PL010) += amba-pl010.o - obj-$(CONFIG_SERIAL_AMBA_PL011) += amba-pl011.o - obj-$(CONFIG_SERIAL_CLPS711X) += clps711x.o -Index: linux-2.6.22.1/include/linux/serial_core.h -=================================================================== ---- linux-2.6.22.1.orig/include/linux/serial_core.h -+++ linux-2.6.22.1/include/linux/serial_core.h -@@ -143,6 +143,9 @@ - #define PORT_KS8695 76 - - -+/* ADMtek ADM5120 SoC */ -+#define PORT_ADM5120 77 -+ - #ifdef __KERNEL__ - - #include -Index: linux-2.6.22.1/drivers/serial/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/serial/Kconfig -+++ linux-2.6.22.1/drivers/serial/Kconfig -@@ -270,6 +270,22 @@ config SERIAL_8250_RM9K - - comment "Non-8250 serial port support" - -+config SERIAL_ADM5120 -+ bool "ADM5120 serial port support" -+ depends on MIPS_ADM5120 -+ select SERIAL_CORE -+ select SERIAL_CORE_CONSOLE -+ help -+ Driver for the on chip UARTs on the ADM5120 SoC -+ -+config ADM5120_NR_UARTS -+ int "Maximum number of ADM5120 serial ports" -+ depends on SERIAL_ADM5120 -+ default "2" -+ ---help--- -+ Set this to the number of serial ports you want the driver to -+ support. -+ - config SERIAL_AMBA_PL010 - tristate "ARM AMBA PL010 serial port support" - depends on ARM_AMBA && (BROKEN || !ARCH_VERSATILE) diff --git a/target/linux/adm5120/patches-2.6.22/100-mtd_myloder_partition_parser.patch b/target/linux/adm5120/patches-2.6.22/100-mtd_myloder_partition_parser.patch deleted file mode 100644 index 574b2d2158..0000000000 --- a/target/linux/adm5120/patches-2.6.22/100-mtd_myloder_partition_parser.patch +++ /dev/null @@ -1,39 +0,0 @@ -Index: linux-2.6.22.1/drivers/mtd/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/Kconfig -+++ linux-2.6.22.1/drivers/mtd/Kconfig -@@ -160,6 +160,22 @@ config MTD_AFS_PARTS - for your particular device. It won't happen automatically. The - 'armflash' map driver (CONFIG_MTD_ARMFLASH) does this, for example. - -+config MTD_MYLOADER_PARTS -+ tristate "MyLoader partition parsing" -+ depends on MIPS_ADM5120 && MTD_PARTITIONS -+ ---help--- -+ MyLoader is a bootloader which allows the user to define partitions -+ in flash devices, by putting a table in the second erase block -+ on the device, similar to a partition table. This table gives the -+ offsets and lengths of the user defined partitions. -+ -+ If you need code which can detect and parse these tables, and -+ register MTD 'partitions' corresponding to each image detected, -+ enable this option. -+ -+ You will still need the parsing functions to be called by the driver -+ for your particular device. It won't happen automatically. -+ - comment "User Modules And Translation Layers" - - config MTD_CHAR -Index: linux-2.6.22.1/drivers/mtd/Makefile -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/Makefile -+++ linux-2.6.22.1/drivers/mtd/Makefile -@@ -11,6 +11,7 @@ obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o - obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o - obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o - obj-$(CONFIG_MTD_AFS_PARTS) += afs.o -+obj-$(CONFIG_MTD_MYLOADER_PARTS) += myloader.o - - # 'Users' - code which presents functionality to userspace. - obj-$(CONFIG_MTD_CHAR) += mtdchar.o diff --git a/target/linux/adm5120/patches-2.6.22/101-cfi_fixup_macronix_bootloc.patch b/target/linux/adm5120/patches-2.6.22/101-cfi_fixup_macronix_bootloc.patch deleted file mode 100644 index 8ccd76f544..0000000000 --- a/target/linux/adm5120/patches-2.6.22/101-cfi_fixup_macronix_bootloc.patch +++ /dev/null @@ -1,95 +0,0 @@ -Index: linux-2.6.22.1/drivers/mtd/chips/cfi_cmdset_0002.c -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/chips/cfi_cmdset_0002.c -+++ linux-2.6.22.1/drivers/mtd/chips/cfi_cmdset_0002.c -@@ -47,12 +47,19 @@ - #define MANUFACTURER_AMD 0x0001 - #define MANUFACTURER_ATMEL 0x001F - #define MANUFACTURER_SST 0x00BF -+#define MANUFACTURER_MACRONIX 0x00C2 - #define SST49LF004B 0x0060 - #define SST49LF040B 0x0050 - #define SST49LF008A 0x005a - #define AT49BV6416 0x00d6 - #define MANUFACTURER_SAMSUNG 0x00ec - -+/* Macronix */ -+#define MX29LV160B 0x2249 /* MX29LV160 Bottom-boot chip */ -+#define MX29LV160T 0x22C4 /* MX29LV160 Top-boot chip */ -+#define MX29LV320B 0x22A8 /* MX29LV320 Bottom-boot chip */ -+#define MX29LV320T 0x22A7 /* MX29LV320 Top-boot chip */ -+ - static int cfi_amdstd_read (struct mtd_info *, loff_t, size_t, size_t *, u_char *); - static int cfi_amdstd_write_words(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); - static int cfi_amdstd_write_buffers(struct mtd_info *, loff_t, size_t, size_t *, const u_char *); -@@ -217,6 +224,41 @@ static void fixup_use_atmel_lock(struct - mtd->flags |= MTD_STUPID_LOCK; - } - -+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC -+/* -+ * Some Macronix chips has no/bad bootblock information in the CFI table -+ */ -+static void fixup_macronix_bootloc(struct mtd_info *mtd, void* param) -+{ -+ struct map_info *map = mtd->priv; -+ struct cfi_private *cfi = map->fldrv_priv; -+ struct cfi_pri_amdstd *extp = cfi->cmdset_priv; -+ __u8 t; -+ -+ switch (cfi->id) { -+ /* TODO: put affected chip ids here */ -+ case MX29LV160B: -+ case MX29LV320B: -+ t = 2; /* Bottom boot */ -+ break; -+ case MX29LV160T: -+ case MX29LV320T: -+ t = 3; /* Top boot */ -+ break; -+ default: -+ return; -+ } -+ -+ if (extp->TopBottom == t) -+ /* boot location detected by the CFI layer is correct */ -+ return; -+ -+ extp->TopBottom = t; -+ printk("%s: Macronix chip detected, id:0x%04X, boot location forced " -+ "to %s\n", map->name, cfi->id, (t == 2) ? "bottom" : "top"); -+} -+#endif /* CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC */ -+ - static struct cfi_fixup cfi_fixup_table[] = { - #ifdef AMD_BOOTLOC_BUG - { CFI_MFR_AMD, CFI_ID_ANY, fixup_amd_bootblock, NULL }, -@@ -231,6 +273,9 @@ static struct cfi_fixup cfi_fixup_table[ - { CFI_MFR_ANY, CFI_ID_ANY, fixup_use_write_buffers, NULL, }, - #endif - { CFI_MFR_ATMEL, CFI_ID_ANY, fixup_convert_atmel_pri, NULL }, -+#ifdef CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC -+ { MANUFACTURER_MACRONIX, CFI_ID_ANY, fixup_macronix_bootloc, NULL, }, -+#endif - { 0, 0, NULL, NULL } - }; - static struct cfi_fixup jedec_fixup_table[] = { -Index: linux-2.6.22.1/drivers/mtd/chips/Kconfig -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/chips/Kconfig -+++ linux-2.6.22.1/drivers/mtd/chips/Kconfig -@@ -196,6 +196,14 @@ config MTD_CFI_AMDSTD - provides support for one of those command sets, used on chips - including the AMD Am29LV320. - -+config MTD_CFI_FIXUP_MACRONIX_BOOTLOC -+ bool "Fix boot-block location for Macronix flash chips" -+ depends on MTD_CFI_AMDSTD -+ help -+ Some Macronix flash chips have no/wrong boot-block location in the -+ CFI table, and the driver may detect the type incorrectly. Select -+ this if your board has such chip. -+ - config MTD_CFI_STAA - tristate "Support for ST (Advanced Architecture) flash chips" - depends on MTD_GEN_PROBE diff --git a/target/linux/adm5120/patches-2.6.22/102-jedec_pmc_39lvxxx_chips.patch b/target/linux/adm5120/patches-2.6.22/102-jedec_pmc_39lvxxx_chips.patch deleted file mode 100644 index abed363edb..0000000000 --- a/target/linux/adm5120/patches-2.6.22/102-jedec_pmc_39lvxxx_chips.patch +++ /dev/null @@ -1,74 +0,0 @@ -Index: linux-2.6.22.1/drivers/mtd/chips/jedec_probe.c -=================================================================== ---- linux-2.6.22.1.orig/drivers/mtd/chips/jedec_probe.c -+++ linux-2.6.22.1/drivers/mtd/chips/jedec_probe.c -@@ -121,6 +121,10 @@ - #define UPD29F064115 0x221C - - /* PMC */ -+#define PM39LV512 0x001B -+#define PM39LV010 0x001C -+#define PM39LV020 0x003D -+#define PM39LV040 0x003E - #define PM49FL002 0x006D - #define PM49FL004 0x006E - #define PM49FL008 0x006A -@@ -1246,6 +1250,58 @@ static const struct amd_flash_info jedec - ERASEINFO(0x02000,2), - ERASEINFO(0x04000,1), - } -+ }, { -+ .mfr_id = MANUFACTURER_PMC, -+ .dev_id = PM39LV512, -+ .name = "PMC Pm39LV512", -+ .uaddr = { -+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ -+ }, -+ .DevSize = SIZE_64KiB, -+ .CmdSet = P_ID_AMD_STD, -+ .NumEraseRegions= 1, -+ .regions = { -+ ERASEINFO(0x01000,16), -+ } -+ }, { -+ .mfr_id = MANUFACTURER_PMC, -+ .dev_id = PM39LV010, -+ .name = "PMC Pm39LV010", -+ .uaddr = { -+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ -+ }, -+ .DevSize = SIZE_128KiB, -+ .CmdSet = P_ID_AMD_STD, -+ .NumEraseRegions= 1, -+ .regions = { -+ ERASEINFO(0x01000,32), -+ } -+ }, { -+ .mfr_id = MANUFACTURER_PMC, -+ .dev_id = PM39LV020, -+ .name = "PMC Pm39LV020", -+ .uaddr = { -+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ -+ }, -+ .DevSize = SIZE_256KiB, -+ .CmdSet = P_ID_AMD_STD, -+ .NumEraseRegions= 1, -+ .regions = { -+ ERASEINFO(0x01000,64), -+ } -+ }, { -+ .mfr_id = MANUFACTURER_PMC, -+ .dev_id = PM39LV040, -+ .name = "PMC Pm39LV040", -+ .uaddr = { -+ [0] = MTD_UADDR_0x0555_0x02AA /* x8 */ -+ }, -+ .DevSize = SIZE_512KiB, -+ .CmdSet = P_ID_AMD_STD, -+ .NumEraseRegions= 1, -+ .regions = { -+ ERASEINFO(0x01000,128), -+ } - }, { - .mfr_id = MANUFACTURER_PMC, - .dev_id = PM49FL002, diff --git a/target/linux/adm5120/patches-2.6.22/103-mtd_trxsplit.patch b/target/linux/adm5120/patches-2.6.22/103-mtd_trxsplit.patch deleted file mode 100644 index c623bc42e4..0000000000 --- a/target/linux/adm5120/patches-2.6.22/103-mtd_trxsplit.patch +++ /dev/null @@ -1,28 +0,0 @@ -Index: linux-2.6.22.4/drivers/mtd/Kconfig -=================================================================== ---- linux-2.6.22.4.orig/drivers/mtd/Kconfig -+++ linux-2.6.22.4/drivers/mtd/Kconfig -@@ -57,6 +57,11 @@ config MTD_ROOTFS_SPLIT - depends on MTD_PARTITIONS - default y - -+config MTD_TRXSPLIT -+ bool "Automatically find and split TRX partitions" -+ depends on MTD_PARTITIONS -+ default n -+ - config MTD_REDBOOT_PARTS - tristate "RedBoot partition table parsing" - depends on MTD_PARTITIONS -Index: linux-2.6.22.4/drivers/mtd/Makefile -=================================================================== ---- linux-2.6.22.4.orig/drivers/mtd/Makefile -+++ linux-2.6.22.4/drivers/mtd/Makefile -@@ -8,6 +8,7 @@ mtd-$(CONFIG_MTD_PARTITIONS) += mtdpart. - obj-$(CONFIG_MTD) += $(mtd-y) - - obj-$(CONFIG_MTD_CONCAT) += mtdconcat.o -+obj-$(CONFIG_MTD_TRXSPLIT) += trxsplit.o - obj-$(CONFIG_MTD_REDBOOT_PARTS) += redboot.o - obj-$(CONFIG_MTD_CMDLINE_PARTS) += cmdlinepart.o - obj-$(CONFIG_MTD_AFS_PARTS) += afs.o diff --git a/target/linux/adm5120/patches-2.6.22/140-cmdline_hack.patch b/target/linux/adm5120/patches-2.6.22/140-cmdline_hack.patch deleted file mode 100644 index 093dfc6b4f..0000000000 --- a/target/linux/adm5120/patches-2.6.22/140-cmdline_hack.patch +++ /dev/null @@ -1,26 +0,0 @@ -Index: linux-2.6.22.1/arch/mips/kernel/head.S -=================================================================== ---- linux-2.6.22.1.orig/arch/mips/kernel/head.S -+++ linux-2.6.22.1/arch/mips/kernel/head.S -@@ -129,14 +129,19 @@ - #endif - .endm - -- - j kernel_entry - nop -- -+ nop -+ - /* - * Reserved space for exception handlers. - * Necessary for machines which link their kernels at KSEG0. -+ * Use as temporary storage for the kernel command line, so that it -+ * can be updated easily without having to relink the kernel. - */ -+ -+EXPORT(_image_cmdline) -+ .ascii "CMDLINE:" - .align 10 - - EXPORT(stext) # used for profiling diff --git a/target/linux/adm5120/patches-2.6.22/200-amba_pl010_hacks.patch b/target/linux/adm5120/patches-2.6.22/200-amba_pl010_hacks.patch deleted file mode 100644 index 840d5a4cf5..0000000000 --- a/target/linux/adm5120/patches-2.6.22/200-amba_pl010_hacks.patch +++ /dev/null @@ -1,297 +0,0 @@ -Index: linux/drivers/serial/amba-pl010.c -=================================================================== ---- linux.orig/drivers/serial/amba-pl010.c -+++ linux/drivers/serial/amba-pl010.c -@@ -52,11 +52,10 @@ - - #include - --#define UART_NR 8 -- - #define SERIAL_AMBA_MAJOR 204 - #define SERIAL_AMBA_MINOR 16 --#define SERIAL_AMBA_NR UART_NR -+#define SERIAL_AMBA_NR CONFIG_SERIAL_AMBA_PL010_NUMPORTS -+#define SERIAL_AMBA_NAME CONFIG_SERIAL_AMBA_PL010_PORTNAME - - #define AMBA_ISR_PASS_LIMIT 256 - -@@ -82,7 +81,7 @@ static void pl010_stop_tx(struct uart_po - struct uart_amba_port *uap = (struct uart_amba_port *)port; - unsigned int cr; - -- cr = readb(uap->port.membase + UART010_CR); -+ cr = readl(uap->port.membase + UART010_CR); - cr &= ~UART010_CR_TIE; - writel(cr, uap->port.membase + UART010_CR); - } -@@ -92,7 +91,7 @@ static void pl010_start_tx(struct uart_p - struct uart_amba_port *uap = (struct uart_amba_port *)port; - unsigned int cr; - -- cr = readb(uap->port.membase + UART010_CR); -+ cr = readl(uap->port.membase + UART010_CR); - cr |= UART010_CR_TIE; - writel(cr, uap->port.membase + UART010_CR); - } -@@ -102,7 +101,7 @@ static void pl010_stop_rx(struct uart_po - struct uart_amba_port *uap = (struct uart_amba_port *)port; - unsigned int cr; - -- cr = readb(uap->port.membase + UART010_CR); -+ cr = readl(uap->port.membase + UART010_CR); - cr &= ~(UART010_CR_RIE | UART010_CR_RTIE); - writel(cr, uap->port.membase + UART010_CR); - } -@@ -112,7 +111,7 @@ static void pl010_enable_ms(struct uart_ - struct uart_amba_port *uap = (struct uart_amba_port *)port; - unsigned int cr; - -- cr = readb(uap->port.membase + UART010_CR); -+ cr = readl(uap->port.membase + UART010_CR); - cr |= UART010_CR_MSIE; - writel(cr, uap->port.membase + UART010_CR); - } -@@ -122,9 +121,9 @@ static void pl010_rx_chars(struct uart_a - struct tty_struct *tty = uap->port.info->tty; - unsigned int status, ch, flag, rsr, max_count = 256; - -- status = readb(uap->port.membase + UART01x_FR); -+ status = readl(uap->port.membase + UART01x_FR); - while (UART_RX_DATA(status) && max_count--) { -- ch = readb(uap->port.membase + UART01x_DR); -+ ch = readl(uap->port.membase + UART01x_DR); - flag = TTY_NORMAL; - - uap->port.icount.rx++; -@@ -133,7 +132,7 @@ static void pl010_rx_chars(struct uart_a - * Note that the error handling code is - * out of the main execution path - */ -- rsr = readb(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX; -+ rsr = readl(uap->port.membase + UART01x_RSR) | UART_DUMMY_RSR_RX; - if (unlikely(rsr & UART01x_RSR_ANY)) { - writel(0, uap->port.membase + UART01x_ECR); - -@@ -165,7 +164,7 @@ static void pl010_rx_chars(struct uart_a - uart_insert_char(&uap->port, rsr, UART01x_RSR_OE, ch, flag); - - ignore_char: -- status = readb(uap->port.membase + UART01x_FR); -+ status = readl(uap->port.membase + UART01x_FR); - } - spin_unlock(&uap->port.lock); - tty_flip_buffer_push(tty); -@@ -210,7 +209,7 @@ static void pl010_modem_status(struct ua - - writel(0, uap->port.membase + UART010_ICR); - -- status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; -+ status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; - - delta = status ^ uap->old_status; - uap->old_status = status; -@@ -238,7 +237,7 @@ static irqreturn_t pl010_int(int irq, vo - - spin_lock(&uap->port.lock); - -- status = readb(uap->port.membase + UART010_IIR); -+ status = readl(uap->port.membase + UART010_IIR); - if (status) { - do { - if (status & (UART010_IIR_RTIS | UART010_IIR_RIS)) -@@ -251,7 +250,7 @@ static irqreturn_t pl010_int(int irq, vo - if (pass_counter-- == 0) - break; - -- status = readb(uap->port.membase + UART010_IIR); -+ status = readl(uap->port.membase + UART010_IIR); - } while (status & (UART010_IIR_RTIS | UART010_IIR_RIS | - UART010_IIR_TIS)); - handled = 1; -@@ -265,7 +264,7 @@ static irqreturn_t pl010_int(int irq, vo - static unsigned int pl010_tx_empty(struct uart_port *port) - { - struct uart_amba_port *uap = (struct uart_amba_port *)port; -- unsigned int status = readb(uap->port.membase + UART01x_FR); -+ unsigned int status = readl(uap->port.membase + UART01x_FR); - return status & UART01x_FR_BUSY ? 0 : TIOCSER_TEMT; - } - -@@ -275,7 +274,7 @@ static unsigned int pl010_get_mctrl(stru - unsigned int result = 0; - unsigned int status; - -- status = readb(uap->port.membase + UART01x_FR); -+ status = readl(uap->port.membase + UART01x_FR); - if (status & UART01x_FR_DCD) - result |= TIOCM_CAR; - if (status & UART01x_FR_DSR) -@@ -301,7 +300,7 @@ static void pl010_break_ctl(struct uart_ - unsigned int lcr_h; - - spin_lock_irqsave(&uap->port.lock, flags); -- lcr_h = readb(uap->port.membase + UART010_LCRH); -+ lcr_h = readl(uap->port.membase + UART010_LCRH); - if (break_state == -1) - lcr_h |= UART01x_LCRH_BRK; - else -@@ -334,7 +333,7 @@ static int pl010_startup(struct uart_por - /* - * initialise the old status of the modem signals - */ -- uap->old_status = readb(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; -+ uap->old_status = readl(uap->port.membase + UART01x_FR) & UART01x_FR_MODEM_ANY; - - /* - * Finally, enable interrupts -@@ -365,7 +364,7 @@ static void pl010_shutdown(struct uart_p - writel(0, uap->port.membase + UART010_CR); - - /* disable break condition and fifos */ -- writel(readb(uap->port.membase + UART010_LCRH) & -+ writel(readl(uap->port.membase + UART010_LCRH) & - ~(UART01x_LCRH_BRK | UART01x_LCRH_FEN), - uap->port.membase + UART010_LCRH); - -@@ -387,7 +386,7 @@ pl010_set_termios(struct uart_port *port - /* - * Ask the core to calculate the divisor for us. - */ -- baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); -+ baud = uart_get_baud_rate(port, termios, old, 0, uap->port.uartclk/16); - quot = uart_get_divisor(port, baud); - - switch (termios->c_cflag & CSIZE) { -@@ -450,7 +449,7 @@ pl010_set_termios(struct uart_port *port - uap->port.ignore_status_mask |= UART_DUMMY_RSR_RX; - - /* first, disable everything */ -- old_cr = readb(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE; -+ old_cr = readl(uap->port.membase + UART010_CR) & ~UART010_CR_MSIE; - - if (UART_ENABLE_MS(port, termios->c_cflag)) - old_cr |= UART010_CR_MSIE; -@@ -540,7 +539,7 @@ static struct uart_ops amba_pl010_pops = - .verify_port = pl010_verify_port, - }; - --static struct uart_amba_port *amba_ports[UART_NR]; -+static struct uart_amba_port *amba_ports[SERIAL_AMBA_NR]; - - #ifdef CONFIG_SERIAL_AMBA_PL010_CONSOLE - -@@ -550,7 +549,7 @@ static void pl010_console_putchar(struct - unsigned int status; - - do { -- status = readb(uap->port.membase + UART01x_FR); -+ status = readl(uap->port.membase + UART01x_FR); - barrier(); - } while (!UART_TX_READY(status)); - writel(ch, uap->port.membase + UART01x_DR); -@@ -567,7 +566,7 @@ pl010_console_write(struct console *co, - /* - * First save the CR then disable the interrupts - */ -- old_cr = readb(uap->port.membase + UART010_CR); -+ old_cr = readl(uap->port.membase + UART010_CR); - writel(UART01x_CR_UARTEN, uap->port.membase + UART010_CR); - - uart_console_write(&uap->port, s, count, pl010_console_putchar); -@@ -577,7 +576,7 @@ pl010_console_write(struct console *co, - * and restore the TCR - */ - do { -- status = readb(uap->port.membase + UART01x_FR); -+ status = readl(uap->port.membase + UART01x_FR); - barrier(); - } while (status & UART01x_FR_BUSY); - writel(old_cr, uap->port.membase + UART010_CR); -@@ -589,9 +588,9 @@ static void __init - pl010_console_get_options(struct uart_amba_port *uap, int *baud, - int *parity, int *bits) - { -- if (readb(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) { -+ if (readl(uap->port.membase + UART010_CR) & UART01x_CR_UARTEN) { - unsigned int lcr_h, quot; -- lcr_h = readb(uap->port.membase + UART010_LCRH); -+ lcr_h = readl(uap->port.membase + UART010_LCRH); - - *parity = 'n'; - if (lcr_h & UART01x_LCRH_PEN) { -@@ -606,8 +605,8 @@ pl010_console_get_options(struct uart_am - else - *bits = 8; - -- quot = readb(uap->port.membase + UART010_LCRL) | -- readb(uap->port.membase + UART010_LCRM) << 8; -+ quot = readl(uap->port.membase + UART010_LCRL) | -+ readl(uap->port.membase + UART010_LCRM) << 8; - *baud = uap->port.uartclk / (16 * (quot + 1)); - } - } -@@ -625,7 +624,7 @@ static int __init pl010_console_setup(st - * if so, search for the first available port that does have - * console support. - */ -- if (co->index >= UART_NR) -+ if (co->index >= SERIAL_AMBA_NR) - co->index = 0; - uap = amba_ports[co->index]; - if (!uap) -@@ -643,7 +642,7 @@ static int __init pl010_console_setup(st - - static struct uart_driver amba_reg; - static struct console amba_console = { -- .name = "ttyAM", -+ .name = SERIAL_AMBA_NAME, - .write = pl010_console_write, - .device = uart_console_device, - .setup = pl010_console_setup, -@@ -659,11 +658,11 @@ static struct console amba_console = { - - static struct uart_driver amba_reg = { - .owner = THIS_MODULE, -- .driver_name = "ttyAM", -- .dev_name = "ttyAM", -+ .driver_name = SERIAL_AMBA_NAME, -+ .dev_name = SERIAL_AMBA_NAME, - .major = SERIAL_AMBA_MAJOR, - .minor = SERIAL_AMBA_MINOR, -- .nr = UART_NR, -+ .nr = SERIAL_AMBA_NR, - .cons = AMBA_CONSOLE, - }; - -Index: linux/drivers/serial/Kconfig -=================================================================== ---- linux.orig/drivers/serial/Kconfig -+++ linux/drivers/serial/Kconfig -@@ -293,10 +293,25 @@ config SERIAL_AMBA_PL010 - help - This selects the ARM(R) AMBA(R) PrimeCell PL010 UART. If you have - an Integrator/AP or Integrator/PP2 platform, or if you have a -- Cirrus Logic EP93xx CPU, say Y or M here. -+ Cirrus Logic EP93xx CPU or an Infineon ADM5120 SOC, say Y or M here. - - If unsure, say N. - -+config SERIAL_AMBA_PL010_NUMPORTS -+ int "Maximum number of AMBA PL010 serial ports" -+ depends on SERIAL_AMBA_PL010 -+ default "8" -+ ---help--- -+ Set this to the number of serial ports you want the AMBA PL010 driver -+ to support. -+ -+config SERIAL_AMBA_PL010_PORTNAME -+ string "Name of the AMBA PL010 serial ports" -+ depends on SERIAL_AMBA_PL010 -+ default "ttyAM" -+ ---help--- -+ ::: To be written ::: -+ - config SERIAL_AMBA_PL010_CONSOLE - bool "Support for console on AMBA serial port" - depends on SERIAL_AMBA_PL010=y diff --git a/target/linux/adm5120/patches-2.6.22/201-amba_bus_hacks.patch b/target/linux/adm5120/patches-2.6.22/201-amba_bus_hacks.patch deleted file mode 100644 index 3b92f25611..0000000000 --- a/target/linux/adm5120/patches-2.6.22/201-amba_bus_hacks.patch +++ /dev/null @@ -1,15 +0,0 @@ -Index: linux/drivers/amba/bus.c -=================================================================== ---- linux.orig/drivers/amba/bus.c -+++ linux/drivers/amba/bus.c -@@ -17,6 +17,10 @@ - #include - #include - -+#ifndef NO_IRQ -+#define NO_IRQ (-1) -+#endif -+ - #define to_amba_device(d) container_of(d, struct amba_device, dev) - #define to_amba_driver(d) container_of(d, struct amba_driver, drv) - diff --git a/target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch b/target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch deleted file mode 100644 index 8c08b74037..0000000000 --- a/target/linux/adm5120/patches-2.6.22/300-i2c_gpio_custom.patch +++ /dev/null @@ -1,30 +0,0 @@ ---- linux-2.6.22.4.orig/drivers/i2c/busses/Kconfig 2007-08-21 06:33:06.000000000 +0200 -+++ linux-2.6.22.4/drivers/i2c/busses/Kconfig 2007-10-09 12:53:13.000000000 +0200 -@@ -125,6 +125,17 @@ - This is a very simple bitbanging I2C driver utilizing the - arch-neutral GPIO API to control the SCL and SDA lines. - -+config I2C_GPIO_CUSTOM -+ tristate "Custom GPIO-based I2C driver" -+ depends on GENERIC_GPIO -+ select I2C_GPIO -+ help -+ This is an I2C driver to register 1 to 4 custom I2C buses using -+ GPIO lines. -+ -+ This support is also available as a module. If so, the module -+ will be called i2c-gpio-custom. -+ - config I2C_HYDRA - tristate "CHRP Apple Hydra Mac I/O I2C interface" - depends on PCI && PPC_CHRP && EXPERIMENTAL ---- linux-2.6.22.4.orig/drivers/i2c/busses/Makefile 2007-08-21 06:33:06.000000000 +0200 -+++ linux-2.6.22.4/drivers/i2c/busses/Makefile 2007-10-09 12:07:45.000000000 +0200 -@@ -13,6 +13,7 @@ - obj-$(CONFIG_I2C_BLACKFIN_TWI) += i2c-bfin-twi.o - obj-$(CONFIG_I2C_ELEKTOR) += i2c-elektor.o - obj-$(CONFIG_I2C_GPIO) += i2c-gpio.o -+obj-$(CONFIG_I2C_GPIO_CUSTOM) += i2c-gpio-custom.o - obj-$(CONFIG_I2C_HYDRA) += i2c-hydra.o - obj-$(CONFIG_I2C_I801) += i2c-i801.o - obj-$(CONFIG_I2C_I810) += i2c-i810.o diff --git a/target/linux/adm5120/patches-2.6.23/006-adm5120_leds.patch b/target/linux/adm5120/patches-2.6.23/006-adm5120_leds.patch index 30f9234e1d..e40b77a364 100644 --- a/target/linux/adm5120/patches-2.6.23/006-adm5120_leds.patch +++ b/target/linux/adm5120/patches-2.6.23/006-adm5120_leds.patch @@ -2,16 +2,10 @@ Index: linux-2.6.23/drivers/leds/Kconfig =================================================================== --- linux-2.6.23.orig/drivers/leds/Kconfig +++ linux-2.6.23/drivers/leds/Kconfig -@@ -18,6 +18,27 @@ config LEDS_CLASS +@@ -18,6 +18,21 @@ config LEDS_CLASS comment "LED drivers" -+config LEDS_GPIO -+ tristate "LED support for LEDS on GPIO lines" -+ depends on LEDS_CLASS && GENERIC_GPIO -+ help -+ This option enables support for LEDs connected to GPIO lines -+ +config LEDS_ADM5120 + tristate "LED Support for ADM5120 GPIO LEDs" + depends on LEDS_GPIO && MIPS_ADM5120 @@ -34,11 +28,10 @@ Index: linux-2.6.23/drivers/leds/Makefile =================================================================== --- linux-2.6.23.orig/drivers/leds/Makefile +++ linux-2.6.23/drivers/leds/Makefile -@@ -5,6 +5,8 @@ obj-$(CONFIG_LEDS_CLASS) += led-class.o +@@ -5,6 +5,7 @@ obj-$(CONFIG_LEDS_CLASS) += led-class.o obj-$(CONFIG_LEDS_TRIGGERS) += led-triggers.o # LED Platform Drivers -+obj-$(CONFIG_LEDS_GPIO) += leds-gpio.o +obj-$(CONFIG_LEDS_ADM5120) += leds-adm5120.o obj-$(CONFIG_LEDS_CORGI) += leds-corgi.o obj-$(CONFIG_LEDS_LOCOMO) += leds-locomo.o diff --git a/target/linux/adm5120/router_be/config-2.6.22 b/target/linux/adm5120/router_be/config-2.6.22 deleted file mode 100644 index 0fca8f8fb1..0000000000 --- a/target/linux/adm5120/router_be/config-2.6.22 +++ /dev/null @@ -1,251 +0,0 @@ -CONFIG_32BIT=y -# CONFIG_64BIT is not set -# CONFIG_64BIT_PHYS_ADDR is not set -CONFIG_ADM5120_CPU_OVERRIDES=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set -# CONFIG_ARCH_SUPPORTS_MSI is not set -CONFIG_ARM_AMBA=y -CONFIG_BASE_SMALL=0 -CONFIG_BAYCOM_SER_FDX=m -CONFIG_BAYCOM_SER_HDX=m -CONFIG_BINFMT_MISC=m -CONFIG_BITREVERSE=y -CONFIG_CIFS_DEBUG2=y -CONFIG_CIFS_EXPERIMENTAL=y -CONFIG_CIFS_STATS2=y -CONFIG_CIFS_WEAK_PW_HASH=y -CONFIG_CIFS_XATTR=y -CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/preinit" -CONFIG_CPU_BIG_ENDIAN=y -CONFIG_CPU_HAS_LLSC=y -CONFIG_CPU_HAS_PREFETCH=y -CONFIG_CPU_HAS_SYNC=y -# CONFIG_CPU_LITTLE_ENDIAN is not set -CONFIG_CPU_MIPS32=y -CONFIG_CPU_MIPS32_R1=y -# CONFIG_CPU_MIPS32_R2 is not set -# CONFIG_CPU_MIPS64_R1 is not set -# CONFIG_CPU_MIPS64_R2 is not set -CONFIG_CPU_MIPSR1=y -# CONFIG_CPU_NEVADA is not set -# CONFIG_CPU_R10000 is not set -# CONFIG_CPU_R3000 is not set -# CONFIG_CPU_R4300 is not set -# CONFIG_CPU_R4X00 is not set -# CONFIG_CPU_R5000 is not set -# CONFIG_CPU_R5432 is not set -# CONFIG_CPU_R6000 is not set -# CONFIG_CPU_R8000 is not set -# CONFIG_CPU_RM7000 is not set -# CONFIG_CPU_RM9000 is not set -# CONFIG_CPU_SB1 is not set -CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_HIGHMEM=y -# CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_TX49XX is not set -# CONFIG_CPU_VR41XX is not set -# CONFIG_DDB5477 is not set -CONFIG_DEVPORT=y -# CONFIG_DM9000 is not set -CONFIG_DMA_NEED_PCI_MAP_STATE=y -CONFIG_DMA_NONCOHERENT=y -CONFIG_EARLY_PRINTK=y -CONFIG_ELF_CORE=y -# CONFIG_EXT3_FS_POSIX_ACL is not set -# CONFIG_EXT3_FS_SECURITY is not set -CONFIG_EXT3_FS_XATTR=y -CONFIG_FS_MBCACHE=m -CONFIG_FS_POSIX_ACL=y -CONFIG_GENERIC_ACL=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -CONFIG_GENERIC_GPIO=y -# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set -# CONFIG_GEN_RTC is not set -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HID=m -CONFIG_HWMON=y -# CONFIG_HWMON_DEBUG_CHIP is not set -CONFIG_HW_HAS_PCI=y -CONFIG_HW_RANDOM=y -CONFIG_HZ=250 -# CONFIG_HZ_100 is not set -CONFIG_HZ_250=y -# CONFIG_I2C is not set -# CONFIG_IDE is not set -CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m -CONFIG_INITRAMFS_SOURCE="" -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y -CONFIG_INPUT=y -# CONFIG_INPUT_EVDEV is not set -CONFIG_IPV6_MIP6=y -CONFIG_IPV6_PRIVACY=y -CONFIG_IPV6_ROUTE_INFO=y -CONFIG_IPV6_TUNNEL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m -CONFIG_IRQ_CPU=y -# CONFIG_JOLIET is not set -CONFIG_LEDS_ADM5120=y -CONFIG_LEDS_ADM5120_DIAG=y -# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set -CONFIG_LEDS_GPIO=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_MACH_ALCHEMY is not set -# CONFIG_MACH_DECSTATION is not set -# CONFIG_MACH_JAZZ is not set -# CONFIG_MACH_VR41XX is not set -CONFIG_MII=m -# CONFIG_MINIX_FS is not set -CONFIG_MIPS=y -CONFIG_MIPS_ADM5120=y -CONFIG_MIPS_ADM5120_ENET=y -# CONFIG_MIPS_ATLAS is not set -# CONFIG_MIPS_COBALT is not set -# CONFIG_MIPS_EV64120 is not set -CONFIG_MIPS_L1_CACHE_SHIFT=5 -# CONFIG_MIPS_MALTA is not set -CONFIG_MIPS_MT_DISABLED=y -# CONFIG_MIPS_MT_SMP is not set -# CONFIG_MIPS_MT_SMTC is not set -# CONFIG_MIPS_SEAD is not set -# CONFIG_MIPS_SIM is not set -# CONFIG_MIPS_VPE_LOADER is not set -CONFIG_MODULE_FORCE_UNLOAD=y -# CONFIG_MOMENCO_OCELOT is not set -# CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set -CONFIG_MTD=y -# CONFIG_MTD_ABSENT is not set -CONFIG_MTD_ADM5120=y -CONFIG_MTD_BLKDEVS=y -CONFIG_MTD_BLOCK=y -CONFIG_MTD_BLOCK2MTD=y -CONFIG_MTD_CFI=y -# CONFIG_MTD_CFI_ADV_OPTIONS is not set -CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y -CONFIG_MTD_CFI_I1=y -CONFIG_MTD_CFI_I2=y -# CONFIG_MTD_CFI_I4 is not set -# CONFIG_MTD_CFI_I8 is not set -# CONFIG_MTD_CFI_INTELEXT is not set -# CONFIG_MTD_CFI_STAA is not set -CONFIG_MTD_CFI_UTIL=y -CONFIG_MTD_CHAR=y -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_COMPLEX_MAPPINGS=y -# CONFIG_MTD_CONCAT is not set -# CONFIG_MTD_DEBUG is not set -# CONFIG_MTD_DOC2000 is not set -# CONFIG_MTD_DOC2001 is not set -# CONFIG_MTD_DOC2001PLUS is not set -CONFIG_MTD_GEN_PROBE=y -# CONFIG_MTD_JEDECPROBE is not set -CONFIG_MTD_MAP_BANK_WIDTH_1=y -# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set -CONFIG_MTD_MAP_BANK_WIDTH_2=y -# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set -CONFIG_MTD_MAP_BANK_WIDTH_4=y -# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set -# CONFIG_MTD_MTDRAM is not set -# CONFIG_MTD_MYLOADER_PARTS is not set -# CONFIG_MTD_ONENAND is not set -CONFIG_MTD_PARTITIONS=y -# CONFIG_MTD_PCI is not set -# CONFIG_MTD_PHRAM is not set -# CONFIG_MTD_PHYSMAP is not set -# CONFIG_MTD_PLATRAM is not set -# CONFIG_MTD_PMC551 is not set -# CONFIG_MTD_RAM is not set -# CONFIG_MTD_REDBOOT_PARTS is not set -# CONFIG_MTD_ROM is not set -# CONFIG_MTD_SLRAM is not set -CONFIG_MTD_TRXSPLIT=y -CONFIG_NETDEV_1000=y -CONFIG_NET_KEY=y -# CONFIG_NET_PCI is not set -# CONFIG_NET_PKTGEN is not set -CONFIG_NET_SCH_FIFO=y -# CONFIG_NET_VENDOR_3COM is not set -CONFIG_NF_CT_PROTO_GRE=m -CONFIG_NF_NAT_PROTO_GRE=m -# CONFIG_PAGE_SIZE_16KB is not set -CONFIG_PAGE_SIZE_4KB=y -# CONFIG_PAGE_SIZE_64KB is not set -# CONFIG_PAGE_SIZE_8KB is not set -# CONFIG_PARTITION_ADVANCED is not set -# CONFIG_PCIPCWATCHDOG is not set -CONFIG_PCI_ADM5120=y -# CONFIG_PMC_YOSEMITE is not set -# CONFIG_PNPACPI is not set -# CONFIG_PNX8550_JBS is not set -# CONFIG_PNX8550_STB810 is not set -# CONFIG_RTC is not set -CONFIG_RWSEM_GENERIC_SPINLOCK=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_SCSI_WAIT_SCAN=m -# CONFIG_SERIAL_8250 is not set -# CONFIG_SERIAL_ADM5120 is not set -CONFIG_SERIAL_AMBA_PL010=y -CONFIG_SERIAL_AMBA_PL010_CONSOLE=y -CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 -CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" -# CONFIG_SERIAL_AMBA_PL011 is not set -CONFIG_SERIO=y -# CONFIG_SERIO_AMBAKMI is not set -# CONFIG_SERIO_I8042 is not set -# CONFIG_SERIO_LIBPS2 is not set -# CONFIG_SERIO_PCIPS2 is not set -# CONFIG_SERIO_RAW is not set -CONFIG_SERIO_SERPORT=y -# CONFIG_SGI_IP22 is not set -# CONFIG_SGI_IP27 is not set -# CONFIG_SGI_IP32 is not set -# CONFIG_SIBYTE_BIGSUR is not set -# CONFIG_SIBYTE_CARMEL is not set -# CONFIG_SIBYTE_CRHINE is not set -# CONFIG_SIBYTE_CRHONE is not set -# CONFIG_SIBYTE_LITTLESUR is not set -# CONFIG_SIBYTE_PTSWARM is not set -# CONFIG_SIBYTE_RHONE is not set -# CONFIG_SIBYTE_SENTOSA is not set -# CONFIG_SIBYTE_SWARM is not set -# CONFIG_SND_USB_AUDIO is not set -CONFIG_SOFT_WATCHDOG=m -# CONFIG_SPARSEMEM_STATIC is not set -CONFIG_SYSVIPC_SYSCTL=y -CONFIG_SYS_HAS_CPU_MIPS32_R1=y -CONFIG_SYS_HAS_EARLY_PRINTK=y -CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y -CONFIG_SYS_SUPPORTS_ARBIT_HZ=y -CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y -CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y -CONFIG_TMPFS_POSIX_ACL=y -# CONFIG_TOSHIBA_JMR3927 is not set -# CONFIG_TOSHIBA_RBTX4927 is not set -# CONFIG_TOSHIBA_RBTX4938 is not set -CONFIG_TRAD_SIGNALS=y -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_USBPCWATCHDOG is not set -# CONFIG_USB_ACM is not set -CONFIG_USB_ADM5120_HCD=m -# CONFIG_USB_ATM is not set -# CONFIG_USB_CATC is not set -# CONFIG_USB_DEVICEFS is not set -# CONFIG_USB_EHCI_HCD is not set -# CONFIG_USB_KAWETH is not set -# CONFIG_USB_PEGASUS is not set -# CONFIG_USB_PRINTER is not set -# CONFIG_USB_SERIAL is not set -# CONFIG_USB_STORAGE is not set -# CONFIG_USB_UHCI_HCD is not set -# CONFIG_USB_USBNET is not set -# CONFIG_USB_USBNET_MII is not set -# CONFIG_VGASTATE is not set -CONFIG_VM_EVENT_COUNTERS=y -# CONFIG_ZD1211RW is not set -CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/adm5120/router_be/config-2.6.23 b/target/linux/adm5120/router_be/config-2.6.23 new file mode 100644 index 0000000000..1c6b7e1f8d --- /dev/null +++ b/target/linux/adm5120/router_be/config-2.6.23 @@ -0,0 +1,254 @@ +CONFIG_32BIT=y +# CONFIG_64BIT is not set +CONFIG_ADM5120_CPU_OVERRIDES=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_ARM_AMBA=y +CONFIG_BASE_SMALL=0 +CONFIG_BAYCOM_SER_FDX=m +CONFIG_BAYCOM_SER_HDX=m +CONFIG_BINFMT_MISC=m +CONFIG_BITREVERSE=y +CONFIG_CIFS_DEBUG2=y +CONFIG_CIFS_EXPERIMENTAL=y +CONFIG_CIFS_STATS2=y +CONFIG_CIFS_WEAK_PW_HASH=y +CONFIG_CIFS_XATTR=y +CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,jffs2 init=/etc/preinit" +CONFIG_CPU_BIG_ENDIAN=y +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +# CONFIG_CPU_LITTLE_ENDIAN is not set +# CONFIG_CPU_LOONGSON2 is not set +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R1=y +# CONFIG_CPU_MIPS32_R2 is not set +# CONFIG_CPU_MIPS64_R1 is not set +# CONFIG_CPU_MIPS64_R2 is not set +CONFIG_CPU_MIPSR1=y +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_TX49XX is not set +# CONFIG_CPU_VR41XX is not set +# CONFIG_CRYPTO_HW is not set +CONFIG_DEVPORT=y +# CONFIG_DM9000 is not set +CONFIG_DMA_NEED_PCI_MAP_STATE=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +CONFIG_ELF_CORE=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +CONFIG_EXT3_FS_XATTR=y +CONFIG_FS_MBCACHE=m +CONFIG_FS_POSIX_ACL=y +CONFIG_GENERIC_ACL=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y +# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HID=m +CONFIG_HID_SUPPORT=y +CONFIG_HWMON=y +# CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_I2C is not set +# CONFIG_IDE is not set +CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m +CONFIG_INITRAMFS_SOURCE="" +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_INPUT=y +# CONFIG_INPUT_EVDEV is not set +CONFIG_IPV6_MIP6=m +CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTE_INFO=y +CONFIG_IPV6_TUNNEL=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m +CONFIG_IRQ_CPU=y +# CONFIG_JOLIET is not set +CONFIG_LEDS_ADM5120=y +CONFIG_LEDS_ADM5120_DIAG=y +# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set +CONFIG_LEDS_GPIO=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_LEMOTE_FULONG is not set +# CONFIG_MACH_ALCHEMY is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_VR41XX is not set +CONFIG_MII=m +# CONFIG_MINIX_FS is not set +CONFIG_MIPS=y +CONFIG_MIPS_ADM5120=y +CONFIG_MIPS_ADM5120_ENET=y +# CONFIG_MIPS_ATLAS is not set +# CONFIG_MIPS_COBALT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +# CONFIG_MIPS_MALTA is not set +CONFIG_MIPS_MT_DISABLED=y +# CONFIG_MIPS_MT_SMP is not set +# CONFIG_MIPS_MT_SMTC is not set +# CONFIG_MIPS_SEAD is not set +# CONFIG_MIPS_SIM is not set +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD=y +# CONFIG_MTD_ABSENT is not set +CONFIG_MTD_ADM5120=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +CONFIG_MTD_BLOCK2MTD=y +CONFIG_MTD_CFI=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +CONFIG_MTD_CHAR=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_CONCAT is not set +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_GEN_PROBE=y +# CONFIG_MTD_JEDECPROBE is not set +CONFIG_MTD_MAP_BANK_WIDTH_1=y +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MTDRAM is not set +# CONFIG_MTD_MYLOADER_PARTS is not set +# CONFIG_MTD_ONENAND is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_PCI is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_PLATRAM is not set +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_SLRAM is not set +CONFIG_MTD_TRXSPLIT=y +CONFIG_NETDEV_1000=y +CONFIG_NET_ACT_POLICE=y +CONFIG_NET_KEY=y +# CONFIG_NET_PCI is not set +# CONFIG_NET_PKTGEN is not set +CONFIG_NET_SCH_FIFO=y +# CONFIG_NET_VENDOR_3COM is not set +CONFIG_NF_CT_PROTO_GRE=m +CONFIG_NF_NAT_PROTO_GRE=m +# CONFIG_NO_IOPORT is not set +# CONFIG_PAGE_SIZE_16KB is not set +CONFIG_PAGE_SIZE_4KB=y +# CONFIG_PAGE_SIZE_64KB is not set +# CONFIG_PAGE_SIZE_8KB is not set +# CONFIG_PARTITION_ADVANCED is not set +# CONFIG_PCIPCWATCHDOG is not set +CONFIG_PCI_ADM5120=y +# CONFIG_PMC_MSP is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_PNX8550_JBS is not set +# CONFIG_PNX8550_STB810 is not set +# CONFIG_RTC is not set +# CONFIG_RTL8187 is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_SCSI_WAIT_SCAN=m +# CONFIG_SENSORS_ABITUGURU3 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SERIAL_8250 is not set +# CONFIG_SERIAL_ADM5120 is not set +CONFIG_SERIAL_AMBA_PL010=y +CONFIG_SERIAL_AMBA_PL010_CONSOLE=y +CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 +CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" +# CONFIG_SERIAL_AMBA_PL011 is not set +CONFIG_SERIO=y +# CONFIG_SERIO_AMBAKMI is not set +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_SERPORT=y +# CONFIG_SGI_IP22 is not set +# CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP32 is not set +# CONFIG_SIBYTE_BIGSUR is not set +# CONFIG_SIBYTE_CARMEL is not set +# CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_PTSWARM is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_SWARM is not set +# CONFIG_SND_USB_AUDIO is not set +CONFIG_SOFT_WATCHDOG=m +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +CONFIG_TMPFS_POSIX_ACL=y +# CONFIG_TOSHIBA_JMR3927 is not set +# CONFIG_TOSHIBA_RBTX4927 is not set +# CONFIG_TOSHIBA_RBTX4938 is not set +CONFIG_TRAD_SIGNALS=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_USB_ACM is not set +CONFIG_USB_ADM5120_HCD=m +# CONFIG_USB_ATM is not set +# CONFIG_USB_CATC is not set +# CONFIG_USB_DEVICEFS is not set +# CONFIG_USB_EHCI_HCD is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_PRINTER is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_SERIAL is not set +# CONFIG_USB_STORAGE is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USB_USBNET is not set +# CONFIG_USB_USBNET_MII is not set +# CONFIG_USER_NS is not set +# CONFIG_VGASTATE is not set +CONFIG_VM_EVENT_COUNTERS=y +# CONFIG_ZD1211RW is not set +CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/adm5120/router_le/config-2.6.22 b/target/linux/adm5120/router_le/config-2.6.22 deleted file mode 100644 index a876583603..0000000000 --- a/target/linux/adm5120/router_le/config-2.6.22 +++ /dev/null @@ -1,276 +0,0 @@ -CONFIG_32BIT=y -# CONFIG_64BIT is not set -# CONFIG_64BIT_PHYS_ADDR is not set -CONFIG_ADM5120_CPU_OVERRIDES=y -# CONFIG_ARCH_HAS_ILOG2_U32 is not set -# CONFIG_ARCH_HAS_ILOG2_U64 is not set -# CONFIG_ARCH_SUPPORTS_MSI is not set -CONFIG_ARM_AMBA=y -CONFIG_BASE_SMALL=0 -CONFIG_BAYCOM_SER_FDX=m -CONFIG_BAYCOM_SER_HDX=m -CONFIG_BINFMT_MISC=m -CONFIG_BITREVERSE=y -CONFIG_CIFS_DEBUG2=y -CONFIG_CIFS_EXPERIMENTAL=y -CONFIG_CIFS_STATS2=y -CONFIG_CIFS_WEAK_PW_HASH=y -CONFIG_CIFS_XATTR=y -CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2 init=/etc/preinit" -# CONFIG_CPU_BIG_ENDIAN is not set -CONFIG_CPU_HAS_LLSC=y -CONFIG_CPU_HAS_PREFETCH=y -CONFIG_CPU_HAS_SYNC=y -CONFIG_CPU_LITTLE_ENDIAN=y -CONFIG_CPU_MIPS32=y -CONFIG_CPU_MIPS32_R1=y -# CONFIG_CPU_MIPS32_R2 is not set -# CONFIG_CPU_MIPS64_R1 is not set -# CONFIG_CPU_MIPS64_R2 is not set -CONFIG_CPU_MIPSR1=y -# CONFIG_CPU_NEVADA is not set -# CONFIG_CPU_R10000 is not set -# CONFIG_CPU_R3000 is not set -# CONFIG_CPU_R4300 is not set -# CONFIG_CPU_R4X00 is not set -# CONFIG_CPU_R5000 is not set -# CONFIG_CPU_R5432 is not set -# CONFIG_CPU_R6000 is not set -# CONFIG_CPU_R8000 is not set -# CONFIG_CPU_RM7000 is not set -# CONFIG_CPU_RM9000 is not set -# CONFIG_CPU_SB1 is not set -CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y -CONFIG_CPU_SUPPORTS_HIGHMEM=y -# CONFIG_CPU_TX39XX is not set -# CONFIG_CPU_TX49XX is not set -# CONFIG_CPU_VR41XX is not set -# CONFIG_DDB5477 is not set -CONFIG_DEVPORT=y -# CONFIG_DM9000 is not set -CONFIG_DMA_NEED_PCI_MAP_STATE=y -CONFIG_DMA_NONCOHERENT=y -CONFIG_EARLY_PRINTK=y -CONFIG_ELF_CORE=y -# CONFIG_EXT3_FS_POSIX_ACL is not set -# CONFIG_EXT3_FS_SECURITY is not set -CONFIG_EXT3_FS_XATTR=y -CONFIG_FS_MBCACHE=m -CONFIG_FS_POSIX_ACL=y -CONFIG_GENERIC_ACL=y -CONFIG_GENERIC_FIND_NEXT_BIT=y -CONFIG_GENERIC_GPIO=y -# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set -# CONFIG_GEN_RTC is not set -CONFIG_HAS_DMA=y -CONFIG_HAS_IOMEM=y -CONFIG_HAS_IOPORT=y -CONFIG_HID=m -CONFIG_HWMON=y -# CONFIG_HWMON_DEBUG_CHIP is not set -CONFIG_HW_HAS_PCI=y -CONFIG_HW_RANDOM=y -CONFIG_HZ=250 -# CONFIG_HZ_100 is not set -CONFIG_HZ_250=y -# CONFIG_I2C is not set -# CONFIG_IDE is not set -CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m -CONFIG_INITRAMFS_SOURCE="" -CONFIG_INOTIFY=y -CONFIG_INOTIFY_USER=y -CONFIG_INPUT=y -# CONFIG_INPUT_EVDEV is not set -CONFIG_IPV6_MIP6=y -CONFIG_IPV6_PRIVACY=y -CONFIG_IPV6_ROUTE_INFO=y -CONFIG_IPV6_TUNNEL=m -CONFIG_IP_NF_TARGET_CLUSTERIP=m -CONFIG_IRQ_CPU=y -# CONFIG_JOLIET is not set -CONFIG_LEDS_ADM5120=y -CONFIG_LEDS_ADM5120_DIAG=y -# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set -CONFIG_LEDS_GPIO=y -CONFIG_LEGACY_PTYS=y -CONFIG_LEGACY_PTY_COUNT=256 -# CONFIG_MACH_ALCHEMY is not set -# CONFIG_MACH_DECSTATION is not set -# CONFIG_MACH_JAZZ is not set -# CONFIG_MACH_VR41XX is not set -CONFIG_MII=m -# CONFIG_MINIX_FS is not set -CONFIG_MIPS=y -CONFIG_MIPS_ADM5120=y -CONFIG_MIPS_ADM5120_ENET=y -# CONFIG_MIPS_ATLAS is not set -# CONFIG_MIPS_COBALT is not set -# CONFIG_MIPS_EV64120 is not set -CONFIG_MIPS_L1_CACHE_SHIFT=5 -# CONFIG_MIPS_MALTA is not set -CONFIG_MIPS_MT_DISABLED=y -# CONFIG_MIPS_MT_SMP is not set -# CONFIG_MIPS_MT_SMTC is not set -# CONFIG_MIPS_SEAD is not set -# CONFIG_MIPS_SIM is not set -# CONFIG_MIPS_VPE_LOADER is not set -CONFIG_MODULE_FORCE_UNLOAD=y -# CONFIG_MOMENCO_OCELOT is not set -# CONFIG_MOMENCO_OCELOT_3 is not set -# CONFIG_MOMENCO_OCELOT_C is not set -CONFIG_MTD=y -# CONFIG_MTD_ABSENT is not set -CONFIG_MTD_ADM5120=y -CONFIG_MTD_BLKDEVS=y -CONFIG_MTD_BLOCK=y -# CONFIG_MTD_BLOCK2MTD is not set -CONFIG_MTD_CFI=y -# CONFIG_MTD_CFI_ADV_OPTIONS is not set -CONFIG_MTD_CFI_AMDSTD=y -CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y -CONFIG_MTD_CFI_I1=y -CONFIG_MTD_CFI_I2=y -# CONFIG_MTD_CFI_I4 is not set -# CONFIG_MTD_CFI_I8 is not set -# CONFIG_MTD_CFI_INTELEXT is not set -# CONFIG_MTD_CFI_STAA is not set -CONFIG_MTD_CFI_UTIL=y -CONFIG_MTD_CHAR=y -CONFIG_MTD_CMDLINE_PARTS=y -CONFIG_MTD_COMPLEX_MAPPINGS=y -# CONFIG_MTD_CONCAT is not set -# CONFIG_MTD_DEBUG is not set -# CONFIG_MTD_DOC2000 is not set -# CONFIG_MTD_DOC2001 is not set -# CONFIG_MTD_DOC2001PLUS is not set -CONFIG_MTD_GEN_PROBE=y -CONFIG_MTD_JEDECPROBE=y -CONFIG_MTD_MAP_BANK_WIDTH_1=y -# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set -CONFIG_MTD_MAP_BANK_WIDTH_2=y -# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set -CONFIG_MTD_MAP_BANK_WIDTH_4=y -# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set -# CONFIG_MTD_MTDRAM is not set -CONFIG_MTD_MYLOADER_PARTS=y -CONFIG_MTD_NAND=y -# CONFIG_MTD_NAND_ADM5120 is not set -# CONFIG_MTD_NAND_CAFE is not set -# CONFIG_MTD_NAND_DISKONCHIP is not set -# CONFIG_MTD_NAND_ECC_SMC is not set -CONFIG_MTD_NAND_IDS=y -# CONFIG_MTD_NAND_MUSEUM_IDS is not set -# CONFIG_MTD_NAND_NANDSIM is not set -CONFIG_MTD_NAND_PLATFORM=y -# CONFIG_MTD_NAND_VERIFY_WRITE is not set -# CONFIG_MTD_ONENAND is not set -CONFIG_MTD_PARTITIONS=y -# CONFIG_MTD_PCI is not set -# CONFIG_MTD_PHRAM is not set -# CONFIG_MTD_PHYSMAP is not set -# CONFIG_MTD_PLATRAM is not set -# CONFIG_MTD_PMC551 is not set -# CONFIG_MTD_RAM is not set -# CONFIG_MTD_REDBOOT_PARTS is not set -# CONFIG_MTD_ROM is not set -# CONFIG_MTD_SLRAM is not set -CONFIG_MTD_TRXSPLIT=y -# CONFIG_NETDEV_1000 is not set -CONFIG_NET_KEY=y -# CONFIG_NET_PCI is not set -# CONFIG_NET_PKTGEN is not set -CONFIG_NET_SCH_FIFO=y -# CONFIG_NET_VENDOR_3COM is not set -CONFIG_NF_CT_PROTO_GRE=m -CONFIG_NF_NAT_PROTO_GRE=m -# CONFIG_PAGE_SIZE_16KB is not set -CONFIG_PAGE_SIZE_4KB=y -# CONFIG_PAGE_SIZE_64KB is not set -# CONFIG_PAGE_SIZE_8KB is not set -# CONFIG_PARTITION_ADVANCED is not set -# CONFIG_PCIPCWATCHDOG is not set -CONFIG_PCI_ADM5120=y -# CONFIG_PMC_YOSEMITE is not set -# CONFIG_PNPACPI is not set -# CONFIG_PNX8550_JBS is not set -# CONFIG_PNX8550_STB810 is not set -# CONFIG_RTC is not set -CONFIG_RWSEM_GENERIC_SPINLOCK=y -CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y -CONFIG_SCSI_WAIT_SCAN=m -# CONFIG_SERIAL_8250 is not set -# CONFIG_SERIAL_ADM5120 is not set -CONFIG_SERIAL_AMBA_PL010=y -CONFIG_SERIAL_AMBA_PL010_CONSOLE=y -CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 -CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" -# CONFIG_SERIAL_AMBA_PL011 is not set -CONFIG_SERIO=y -# CONFIG_SERIO_AMBAKMI is not set -# CONFIG_SERIO_I8042 is not set -# CONFIG_SERIO_LIBPS2 is not set -# CONFIG_SERIO_PCIPS2 is not set -# CONFIG_SERIO_RAW is not set -CONFIG_SERIO_SERPORT=y -# CONFIG_SGI_IP22 is not set -# CONFIG_SGI_IP27 is not set -# CONFIG_SGI_IP32 is not set -# CONFIG_SIBYTE_BIGSUR is not set -# CONFIG_SIBYTE_CARMEL is not set -# CONFIG_SIBYTE_CRHINE is not set -# CONFIG_SIBYTE_CRHONE is not set -# CONFIG_SIBYTE_LITTLESUR is not set -# CONFIG_SIBYTE_PTSWARM is not set -# CONFIG_SIBYTE_RHONE is not set -# CONFIG_SIBYTE_SENTOSA is not set -# CONFIG_SIBYTE_SWARM is not set -CONFIG_SOFT_WATCHDOG=m -# CONFIG_SPARSEMEM_STATIC is not set -CONFIG_SYSVIPC_SYSCTL=y -CONFIG_SYS_HAS_CPU_MIPS32_R1=y -CONFIG_SYS_HAS_EARLY_PRINTK=y -CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y -CONFIG_SYS_SUPPORTS_ARBIT_HZ=y -CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y -CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y -CONFIG_TMPFS_POSIX_ACL=y -# CONFIG_TOSHIBA_JMR3927 is not set -# CONFIG_TOSHIBA_RBTX4927 is not set -# CONFIG_TOSHIBA_RBTX4938 is not set -CONFIG_TRAD_SIGNALS=y -# CONFIG_UNUSED_SYMBOLS is not set -# CONFIG_USBPCWATCHDOG is not set -# CONFIG_USB_ACM is not set -CONFIG_USB_ADM5120_HCD=m -# CONFIG_USB_ALI_M5632 is not set -# CONFIG_USB_AN2720 is not set -# CONFIG_USB_CATC is not set -# CONFIG_USB_EHCI_BIG_ENDIAN_MMIO is not set -CONFIG_USB_EHCI_HCD=m -# CONFIG_USB_KAWETH is not set -# CONFIG_USB_NET_DM9601 is not set -# CONFIG_USB_NET_GL620A is not set -# CONFIG_USB_NET_MCS7830 is not set -# CONFIG_USB_NET_PLUSB is not set -# CONFIG_USB_NET_RNDIS_HOST is not set -# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set -# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set -CONFIG_USB_OHCI_HCD=m -# CONFIG_USB_PEGASUS is not set -# CONFIG_USB_SERIAL is not set -# CONFIG_USB_UHCI_HCD is not set -# CONFIG_VGASTATE is not set -CONFIG_VIDEO_V4L1=y -CONFIG_VM_EVENT_COUNTERS=y -CONFIG_YAFFS_9BYTE_TAGS=y -# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set -CONFIG_YAFFS_AUTO_YAFFS2=y -CONFIG_YAFFS_CHECKPOINT_RESERVED_BLOCKS=0 -# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set -# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set -CONFIG_YAFFS_FS=y -CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y -CONFIG_YAFFS_YAFFS1=y -CONFIG_YAFFS_YAFFS2=y -# CONFIG_ZD1211RW is not set -CONFIG_ZONE_DMA_FLAG=0 diff --git a/target/linux/adm5120/router_le/config-2.6.23 b/target/linux/adm5120/router_le/config-2.6.23 new file mode 100644 index 0000000000..5165b54f44 --- /dev/null +++ b/target/linux/adm5120/router_le/config-2.6.23 @@ -0,0 +1,279 @@ +CONFIG_32BIT=y +# CONFIG_64BIT is not set +CONFIG_ADM5120_CPU_OVERRIDES=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +CONFIG_ARM_AMBA=y +CONFIG_BASE_SMALL=0 +CONFIG_BAYCOM_SER_FDX=m +CONFIG_BAYCOM_SER_HDX=m +CONFIG_BINFMT_MISC=m +CONFIG_BITREVERSE=y +CONFIG_CIFS_DEBUG2=y +CONFIG_CIFS_EXPERIMENTAL=y +CONFIG_CIFS_STATS2=y +CONFIG_CIFS_WEAK_PW_HASH=y +CONFIG_CIFS_XATTR=y +CONFIG_CMDLINE="console=ttyS0,115200 rootfstype=squashfs,yaffs2,jffs2 init=/etc/preinit" +# CONFIG_CPU_BIG_ENDIAN is not set +CONFIG_CPU_HAS_LLSC=y +CONFIG_CPU_HAS_PREFETCH=y +CONFIG_CPU_HAS_SYNC=y +CONFIG_CPU_LITTLE_ENDIAN=y +# CONFIG_CPU_LOONGSON2 is not set +CONFIG_CPU_MIPS32=y +CONFIG_CPU_MIPS32_R1=y +# CONFIG_CPU_MIPS32_R2 is not set +# CONFIG_CPU_MIPS64_R1 is not set +# CONFIG_CPU_MIPS64_R2 is not set +CONFIG_CPU_MIPSR1=y +# CONFIG_CPU_NEVADA is not set +# CONFIG_CPU_R10000 is not set +# CONFIG_CPU_R3000 is not set +# CONFIG_CPU_R4300 is not set +# CONFIG_CPU_R4X00 is not set +# CONFIG_CPU_R5000 is not set +# CONFIG_CPU_R5432 is not set +# CONFIG_CPU_R6000 is not set +# CONFIG_CPU_R8000 is not set +# CONFIG_CPU_RM7000 is not set +# CONFIG_CPU_RM9000 is not set +# CONFIG_CPU_SB1 is not set +CONFIG_CPU_SUPPORTS_32BIT_KERNEL=y +CONFIG_CPU_SUPPORTS_HIGHMEM=y +# CONFIG_CPU_TX39XX is not set +# CONFIG_CPU_TX49XX is not set +# CONFIG_CPU_VR41XX is not set +# CONFIG_CRYPTO_HW is not set +CONFIG_DEVPORT=y +# CONFIG_DM9000 is not set +CONFIG_DMA_NEED_PCI_MAP_STATE=y +CONFIG_DMA_NONCOHERENT=y +CONFIG_EARLY_PRINTK=y +CONFIG_ELF_CORE=y +# CONFIG_EXT3_FS_POSIX_ACL is not set +# CONFIG_EXT3_FS_SECURITY is not set +CONFIG_EXT3_FS_XATTR=y +CONFIG_FS_MBCACHE=m +CONFIG_FS_POSIX_ACL=y +CONFIG_GENERIC_ACL=y +CONFIG_GENERIC_FIND_NEXT_BIT=y +CONFIG_GENERIC_GPIO=y +# CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ is not set +CONFIG_HAS_DMA=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HID=m +CONFIG_HID_SUPPORT=y +CONFIG_HWMON=y +# CONFIG_HWMON_DEBUG_CHIP is not set +CONFIG_HW_HAS_PCI=y +CONFIG_HW_RANDOM=y +CONFIG_HZ=250 +# CONFIG_HZ_100 is not set +CONFIG_HZ_250=y +# CONFIG_I2C is not set +# CONFIG_IDE is not set +CONFIG_INET6_XFRM_MODE_ROUTEOPTIMIZATION=m +CONFIG_INITRAMFS_SOURCE="" +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_INPUT=y +# CONFIG_INPUT_EVDEV is not set +CONFIG_IPV6_MIP6=m +CONFIG_IPV6_PRIVACY=y +CONFIG_IPV6_ROUTE_INFO=y +CONFIG_IPV6_TUNNEL=m +CONFIG_IP_NF_TARGET_CLUSTERIP=m +CONFIG_IRQ_CPU=y +# CONFIG_JOLIET is not set +CONFIG_LEDS_ADM5120=y +CONFIG_LEDS_ADM5120_DIAG=y +# CONFIG_LEDS_ADM5120_EXPERIMENTAL is not set +CONFIG_LEDS_GPIO=y +CONFIG_LEGACY_PTYS=y +CONFIG_LEGACY_PTY_COUNT=256 +# CONFIG_LEMOTE_FULONG is not set +# CONFIG_MACH_ALCHEMY is not set +# CONFIG_MACH_DECSTATION is not set +# CONFIG_MACH_JAZZ is not set +# CONFIG_MACH_VR41XX is not set +CONFIG_MII=m +# CONFIG_MINIX_FS is not set +CONFIG_MIPS=y +CONFIG_MIPS_ADM5120=y +CONFIG_MIPS_ADM5120_ENET=y +# CONFIG_MIPS_ATLAS is not set +# CONFIG_MIPS_COBALT is not set +CONFIG_MIPS_L1_CACHE_SHIFT=5 +# CONFIG_MIPS_MALTA is not set +CONFIG_MIPS_MT_DISABLED=y +# CONFIG_MIPS_MT_SMP is not set +# CONFIG_MIPS_MT_SMTC is not set +# CONFIG_MIPS_SEAD is not set +# CONFIG_MIPS_SIM is not set +CONFIG_MODULE_FORCE_UNLOAD=y +CONFIG_MTD=y +# CONFIG_MTD_ABSENT is not set +CONFIG_MTD_ADM5120=y +CONFIG_MTD_BLKDEVS=y +CONFIG_MTD_BLOCK=y +# CONFIG_MTD_BLOCK2MTD is not set +CONFIG_MTD_CFI=y +# CONFIG_MTD_CFI_ADV_OPTIONS is not set +CONFIG_MTD_CFI_AMDSTD=y +CONFIG_MTD_CFI_FIXUP_MACRONIX_BOOTLOC=y +CONFIG_MTD_CFI_I1=y +CONFIG_MTD_CFI_I2=y +# CONFIG_MTD_CFI_I4 is not set +# CONFIG_MTD_CFI_I8 is not set +# CONFIG_MTD_CFI_INTELEXT is not set +# CONFIG_MTD_CFI_STAA is not set +CONFIG_MTD_CFI_UTIL=y +CONFIG_MTD_CHAR=y +CONFIG_MTD_CMDLINE_PARTS=y +CONFIG_MTD_COMPLEX_MAPPINGS=y +# CONFIG_MTD_CONCAT is not set +# CONFIG_MTD_DEBUG is not set +# CONFIG_MTD_DOC2000 is not set +# CONFIG_MTD_DOC2001 is not set +# CONFIG_MTD_DOC2001PLUS is not set +CONFIG_MTD_GEN_PROBE=y +CONFIG_MTD_JEDECPROBE=y +CONFIG_MTD_MAP_BANK_WIDTH_1=y +# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set +CONFIG_MTD_MAP_BANK_WIDTH_2=y +# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set +CONFIG_MTD_MAP_BANK_WIDTH_4=y +# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set +# CONFIG_MTD_MTDRAM is not set +CONFIG_MTD_MYLOADER_PARTS=y +CONFIG_MTD_NAND=y +# CONFIG_MTD_NAND_ADM5120 is not set +# CONFIG_MTD_NAND_CAFE is not set +# CONFIG_MTD_NAND_DISKONCHIP is not set +# CONFIG_MTD_NAND_ECC_SMC is not set +CONFIG_MTD_NAND_IDS=y +# CONFIG_MTD_NAND_MUSEUM_IDS is not set +# CONFIG_MTD_NAND_NANDSIM is not set +CONFIG_MTD_NAND_PLATFORM=y +# CONFIG_MTD_NAND_VERIFY_WRITE is not set +# CONFIG_MTD_ONENAND is not set +CONFIG_MTD_PARTITIONS=y +# CONFIG_MTD_PCI is not set +# CONFIG_MTD_PHRAM is not set +# CONFIG_MTD_PHYSMAP is not set +# CONFIG_MTD_PLATRAM is not set +# CONFIG_MTD_PMC551 is not set +# CONFIG_MTD_RAM is not set +# CONFIG_MTD_REDBOOT_PARTS is not set +# CONFIG_MTD_ROM is not set +# CONFIG_MTD_SLRAM is not set +CONFIG_MTD_TRXSPLIT=y +# CONFIG_NETDEV_1000 is not set +# CONFIG_NETFILTER_XT_TARGET_TARPIT is not set +CONFIG_NET_ACT_POLICE=y +CONFIG_NET_KEY=y +# CONFIG_NET_PCI is not set +# CONFIG_NET_PKTGEN is not set +CONFIG_NET_SCH_FIFO=y +# CONFIG_NET_VENDOR_3COM is not set +CONFIG_NF_CT_PROTO_GRE=m +CONFIG_NF_NAT_PROTO_GRE=m +# CONFIG_NO_IOPORT is not set +# CONFIG_PAGE_SIZE_16KB is not set +CONFIG_PAGE_SIZE_4KB=y +# CONFIG_PAGE_SIZE_64KB is not set +# CONFIG_PAGE_SIZE_8KB is not set +# CONFIG_PARTITION_ADVANCED is not set +# CONFIG_PCIPCWATCHDOG is not set +CONFIG_PCI_ADM5120=y +# CONFIG_PMC_MSP is not set +# CONFIG_PMC_YOSEMITE is not set +# CONFIG_PNX8550_JBS is not set +# CONFIG_PNX8550_STB810 is not set +# CONFIG_RTC is not set +# CONFIG_RTL8187 is not set +CONFIG_RWSEM_GENERIC_SPINLOCK=y +CONFIG_SCHED_NO_NO_OMIT_FRAME_POINTER=y +CONFIG_SCSI_WAIT_SCAN=m +# CONFIG_SENSORS_ABITUGURU3 is not set +# CONFIG_SENSORS_PC87360 is not set +# CONFIG_SERIAL_8250 is not set +# CONFIG_SERIAL_ADM5120 is not set +CONFIG_SERIAL_AMBA_PL010=y +CONFIG_SERIAL_AMBA_PL010_CONSOLE=y +CONFIG_SERIAL_AMBA_PL010_NUMPORTS=2 +CONFIG_SERIAL_AMBA_PL010_PORTNAME="ttyS" +# CONFIG_SERIAL_AMBA_PL011 is not set +CONFIG_SERIO=y +# CONFIG_SERIO_AMBAKMI is not set +# CONFIG_SERIO_I8042 is not set +# CONFIG_SERIO_LIBPS2 is not set +# CONFIG_SERIO_PCIPS2 is not set +# CONFIG_SERIO_RAW is not set +CONFIG_SERIO_SERPORT=y +# CONFIG_SGI_IP22 is not set +# CONFIG_SGI_IP27 is not set +# CONFIG_SGI_IP32 is not set +# CONFIG_SIBYTE_BIGSUR is not set +# CONFIG_SIBYTE_CARMEL is not set +# CONFIG_SIBYTE_CRHINE is not set +# CONFIG_SIBYTE_CRHONE is not set +# CONFIG_SIBYTE_LITTLESUR is not set +# CONFIG_SIBYTE_PTSWARM is not set +# CONFIG_SIBYTE_RHONE is not set +# CONFIG_SIBYTE_SENTOSA is not set +# CONFIG_SIBYTE_SWARM is not set +CONFIG_SOFT_WATCHDOG=m +# CONFIG_SPARSEMEM_STATIC is not set +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_SYS_HAS_CPU_MIPS32_R1=y +CONFIG_SYS_HAS_EARLY_PRINTK=y +CONFIG_SYS_SUPPORTS_32BIT_KERNEL=y +CONFIG_SYS_SUPPORTS_ARBIT_HZ=y +CONFIG_SYS_SUPPORTS_BIG_ENDIAN=y +CONFIG_SYS_SUPPORTS_LITTLE_ENDIAN=y +CONFIG_TMPFS_POSIX_ACL=y +# CONFIG_TOSHIBA_JMR3927 is not set +# CONFIG_TOSHIBA_RBTX4927 is not set +# CONFIG_TOSHIBA_RBTX4938 is not set +CONFIG_TRAD_SIGNALS=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_USBPCWATCHDOG is not set +# CONFIG_USB_ACM is not set +CONFIG_USB_ADM5120_HCD=m +# CONFIG_USB_ALI_M5632 is not set +# CONFIG_USB_AN2720 is not set +# CONFIG_USB_CATC is not set +CONFIG_USB_EHCI_HCD=m +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_NET_DM9601 is not set +# CONFIG_USB_NET_GL620A is not set +# CONFIG_USB_NET_MCS7830 is not set +# CONFIG_USB_NET_PLUSB is not set +# CONFIG_USB_NET_RNDIS_HOST is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set +# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set +CONFIG_USB_OHCI_HCD=m +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_R8A66597_HCD is not set +# CONFIG_USB_SERIAL is not set +# CONFIG_USB_UHCI_HCD is not set +# CONFIG_USER_NS is not set +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_V4L1=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_YAFFS_9BYTE_TAGS=y +# CONFIG_YAFFS_ALWAYS_CHECK_CHUNK_ERASED is not set +CONFIG_YAFFS_AUTO_YAFFS2=y +CONFIG_YAFFS_CHECKPOINT_RESERVED_BLOCKS=0 +# CONFIG_YAFFS_DISABLE_LAZY_LOAD is not set +# CONFIG_YAFFS_DISABLE_WIDE_TNODES is not set +CONFIG_YAFFS_FS=y +CONFIG_YAFFS_SHORT_NAMES_IN_RAM=y +CONFIG_YAFFS_YAFFS1=y +CONFIG_YAFFS_YAFFS2=y +# CONFIG_ZD1211RW is not set +CONFIG_ZONE_DMA_FLAG=0