From: Chuanhong Guo <gch981213@gmail.com>
Date: Fri, 29 Dec 2017 04:35:32 +0000 (+0800)
Subject: ramips: fix lenovo newifi-y1 switch and LED config
X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a657978fe7ff4cacc97c753961b75de547e5d5d9;p=openwrt%2Fstaging%2Fzorun.git

ramips: fix lenovo newifi-y1 switch and LED config

There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on
port4.

Use a standalone switch configuration to match this and use the switch
trigger so that LAN LED could indicate the connetction status for both
lan ports correctly.

This patch also drop the internet led configuration, because there is a
WAN led for port4 and eth0.2 isn't always used as WAN.

Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
---

diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds b/target/linux/ramips/base-files/etc/board.d/01_leds
index 03d084f17b..55976edec8 100755
--- a/target/linux/ramips/base-files/etc/board.d/01_leds
+++ b/target/linux/ramips/base-files/etc/board.d/01_leds
@@ -453,8 +453,7 @@ y1)
 	set_usb_led "$boardname:blue:usb"
 	ucidef_set_led_netdev "wifi" "WIFI" "$boardname:blue:wifi" "wlan1"
 	ucidef_set_led_netdev "wifi5g" "WIFI5G" "$boardname:blue:wifi5g" "wlan0"
-	ucidef_set_led_netdev "lan" "LAN" "$boardname:blue:lan" "eth0.1" "tx rx"
-	ucidef_set_led_netdev "wan" "WAN" "$boardname:blue:internet" "eth0.2" "tx rx"
+	ucidef_set_led_switch "lan" "LAN" "$boardname:blue:lan" "switch0" "0x03"
 	;;
 y1s)
 	set_usb_led "$boardname:blue:usb"
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network b/target/linux/ramips/base-files/etc/board.d/02_network
index b8116c773b..48fdfdf3f1 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -111,7 +111,6 @@ ramips_setup_interfaces()
 	wndr3700v5|\
 	wt1520-4M|\
 	wt1520-8M|\
-	y1|\
 	youku-yk1|\
 	zbt-ape522ii|\
 	zbt-we1326|\
@@ -348,6 +347,10 @@ ramips_setup_interfaces()
 		ucidef_add_switch "switch0" \
 			"1:lan" "2:lan" "0:wan" "6@eth0"
 		;;
+	y1)
+		ucidef_add_switch "switch0" \
+			"0:lan:2" "1:lan:1" "4:wan" "6@eth0"
+		;;
 	*)
 		RT3X5X=`cat /proc/cpuinfo | egrep "(RT3.5|RT5350)"`
 		if [ -n "${RT3X5X}" ]; then