From: Roger Pueyo Centelles Date: Fri, 18 Dec 2020 21:26:55 +0000 (+0100) Subject: ath79: mikrotik: enable SFP on RB922UAGS-5HPaCD X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a524a0dff80e9bf833ef8c08308923398d3d46a6;p=openwrt%2Fstaging%2Fadrian.git ath79: mikrotik: enable SFP on RB922UAGS-5HPaCD This patch enables the SFP cage on the MikroTik RouterBOARD 922UAGS-5HPacD. GPIO16 (tx-disable-gpios) should be governed by the SFP driver to enable or disable transmission, but no change is observed. Therefore, it is left as output high to ensure the SFP module is forced to transmit. Tested on a RouterBOARD 922UAGS-5HPacD board, with a CISCO GLC-LH-SMD 1310nm module and an unbranded GLC-T RJ45 Gigabit module. PC=>router iperf3 tests deliver 440/300 Mbps up/down, both via regular eth0 port or SFP port with RJ45 module. Bridge between eth0 and eth1 delivers 950 Mbps symmetric. Signed-off-by: Roger Pueyo Centelles (cherry picked from commit 4387fe00cb7536d9d341f6d27e465ff0f0b29b1b) --- diff --git a/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts index 8ad834fe61..36979bbd33 100644 --- a/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts +++ b/target/linux/ath79/dts/qca9558_mikrotik_routerboard-922uags-5hpacd.dts @@ -23,6 +23,27 @@ gpios = <&gpio 13 GPIO_ACTIVE_HIGH>; }; }; + + i2c: i2c { + compatible = "i2c-gpio"; + + sda-gpios = <&gpio 18 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + scl-gpios = <&gpio 19 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; + i2c-gpio,delay-us = <5>; + i2c-gpio,timeout-ms = <1>; + }; + + sfp1: sfp { + compatible = "sff,sfp"; + + i2c-bus = <&i2c>; + maximum-power-milliwatt = <1000>; + los-gpios = <&gpio 21 GPIO_ACTIVE_HIGH>; + mod-def0-gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + tx-disable-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>; + // Toggling GPIO16 actually enables/disables the transmitter, + // but the SFP driver does not seem to be using it. + }; }; &pcie0 { @@ -55,3 +76,30 @@ &usb_phy1 { status = "okay"; }; + +&mdio1 { + status = "okay"; + + phy_sfp: ethernet-phy@0 { + reg = <0>; + phy-mode = "sgmii"; + sfp = <&sfp1>; + }; +}; + +ð1 { + status = "okay"; + + phy-handle = <&phy_sfp>; + pll-data = <0x03000000 0x00000101 0x00001616>; + qca955x-sgmii-fixup; + + gmac-config { + device = <&gmac>; + }; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; diff --git a/target/linux/ath79/image/mikrotik.mk b/target/linux/ath79/image/mikrotik.mk index b7d745bc77..74f8603b5a 100644 --- a/target/linux/ath79/image/mikrotik.mk +++ b/target/linux/ath79/image/mikrotik.mk @@ -22,7 +22,8 @@ define Device/mikrotik_routerboard-922uags-5hpacd $(Device/mikrotik_nand) SOC := qca9558 DEVICE_MODEL := RouterBOARD 922UAGS-5HPacD - DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 + DEVICE_PACKAGES += kmod-ath10k-ct ath10k-firmware-qca988x-ct kmod-usb2 \ + kmod-i2c-gpio kmod-sfp SUPPORTED_DEVICES += rb-922uags-5hpacd endef TARGET_DEVICES += mikrotik_routerboard-922uags-5hpacd diff --git a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network index 584acc0feb..c407da6dcd 100755 --- a/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network +++ b/target/linux/ath79/mikrotik/base-files/etc/board.d/02_network @@ -16,7 +16,6 @@ ath79_setup_interfaces() "0@eth1" "1:lan:4" "2:lan:1" "3:lan:2" "4:lan:3" ;; mikrotik,routerboard-921gs-5hpacd-15s|\ - mikrotik,routerboard-922uags-5hpacd|\ mikrotik,routerboard-lhg-2nd|\ mikrotik,routerboard-sxt-5nd-r2|\ mikrotik,routerboard-wap-g-5hact2hnd|\ diff --git a/target/linux/ath79/mikrotik/config-default b/target/linux/ath79/mikrotik/config-default index f713fc36cf..8609893f6e 100644 --- a/target/linux/ath79/mikrotik/config-default +++ b/target/linux/ath79/mikrotik/config-default @@ -24,6 +24,7 @@ CONFIG_MTD_UBI=y CONFIG_MTD_UBI_BLOCK=y CONFIG_MTD_UBI_WL_THRESHOLD=4096 CONFIG_MTD_UBI_BEB_LIMIT=20 +CONFIG_NET_DSA=y CONFIG_NET_SWITCHDEV=y CONFIG_PCI_AR71XX=y CONFIG_PHY_AR7100_USB=y