From: Daniel Golle <daniel@makrotopia.org>
Date: Thu, 28 Jul 2022 14:45:03 +0000 (+0200)
Subject: Revert "realtek: remove support for HPE 1920 series"
X-Git-Url: http://git.lede-project.org./?a=commitdiff_plain;h=a49212d762fb2635564cd3365651da51d0c535d9;p=openwrt%2Fstaging%2Frmilecki.git

Revert "realtek: remove support for HPE 1920 series"

This reverts commit a63aeaecf1f3387df020854c9b22a365207399ce.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---

diff --git a/target/linux/realtek/base-files/etc/board.d/02_network b/target/linux/realtek/base-files/etc/board.d/02_network
index af9db848dd8..5356bcac65d 100644
--- a/target/linux/realtek/base-files/etc/board.d/02_network
+++ b/target/linux/realtek/base-files/etc/board.d/02_network
@@ -22,9 +22,20 @@ ucidef_set_bridge_device switch
 ucidef_set_interface_lan "$lan_list"
 
 lan_mac=""
+lan_mac_start=""
 lan_mac_end=""
 label_mac=""
 case $board in
+hpe,1920-8g|\
+hpe,1920-16g|\
+hpe,1920-24g)
+	label_mac=$(mtd_get_mac_binary factory 0x68)
+	lan_mac=$label_mac
+	mac_count1=$(hexdump -v -n 4 -s 0x110 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
+	mac_count2=$(hexdump -v -n 4 -s 0x114 -e '4 "%d"' $(find_mtd_part factory) 2>/dev/null)
+	lan_mac_start=$(macaddr_add $lan_mac 2)
+	lan_mac_end=$(macaddr_add $lan_mac $((mac_count2-mac_count1)))
+	;;
 *)
 	lan_mac=$(mtd_get_mac_ascii u-boot-env2 mac_start)
 	lan_mac_end=$(mtd_get_mac_ascii u-boot-env2 mac_end)
@@ -36,10 +47,11 @@ esac
 ucidef_set_interface_macaddr "lan" $lan_mac
 ucidef_set_bridge_mac "$lan_mac"
 ucidef_set_network_device_mac eth0 $lan_mac
+[ -z "$lan_mac_start" ] && lan_mac_start=$lan_mac
 for lan in $lan_list; do
-	ucidef_set_network_device_mac $lan $lan_mac
-	[ -z "$lan_mac_end" ] || [ "$lan_mac" == "$lan_mac_end" ] && lan_mac=$(macaddr_setbit_la $lan_mac)
-	lan_mac=$(macaddr_add $lan_mac 1)
+	ucidef_set_network_device_mac $lan $lan_mac_start
+	[ -z "$lan_mac_end" ] || [ "$lan_mac_start" == "$lan_mac_end" ] && lan_mac_start=$(macaddr_setbit_la $lan_mac_start)
+	lan_mac_start=$(macaddr_add $lan_mac_start 1)
 done
 [ -n "$label_mac" ] && ucidef_set_label_macaddr $label_mac
 
diff --git a/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
new file mode 100644
index 00000000000..b51c75f3552
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8380_hpe_1920-8g.dts
@@ -0,0 +1,113 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl838x.dtsi"
+#include "rtl838x_hpe_1920.dtsi"
+
+/ {
+	compatible = "hpe,1920-8g", "realtek,rtl838x-soc";
+	model = "HPE 1920-8G (JG920A)";
+
+	gpio1: rtl8231-gpio {
+		compatible = "realtek,rtl8231-gpio";
+		#gpio-cells = <2>;
+		gpio-controller;
+		indirect-access-bus-id = <0>;
+	};
+
+	i2c0: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	sfp0: sfp-0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c0>;
+		los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
+		// tx-fault and tx-disable unconnected
+	};
+
+	i2c1: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
+		// tx-fault and tx-disable unconnected
+	};
+};
+
+&ethernet0 {
+	mdio: mdio-bus {
+		compatible = "realtek,rtl838x-mdio";
+		regmap = <&ethernet0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		INTERNAL_PHY(8)
+		INTERNAL_PHY(9)
+		INTERNAL_PHY(10)
+		INTERNAL_PHY(11)
+		INTERNAL_PHY(12)
+		INTERNAL_PHY(13)
+		INTERNAL_PHY(14)
+		INTERNAL_PHY(15)
+
+		INTERNAL_PHY(24)
+		INTERNAL_PHY(26)
+	};
+};
+
+&switch0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		SWITCH_PORT(8, 1, internal)
+		SWITCH_PORT(9, 2, internal)
+		SWITCH_PORT(10, 3, internal)
+		SWITCH_PORT(11, 4, internal)
+		SWITCH_PORT(12, 5, internal)
+		SWITCH_PORT(13, 6, internal)
+		SWITCH_PORT(14, 7, internal)
+		SWITCH_PORT(15, 8, internal)
+
+		port@24 {
+			reg = <24>;
+			label = "lan9";
+			phy-mode = "1000base-x";
+			managed = "in-band-status";
+			sfp = <&sfp0>;
+		};
+
+		port@26 {
+			reg = <26>;
+			label = "lan10";
+			phy-mode = "1000base-x";
+			managed = "in-band-status";
+			sfp = <&sfp1>;
+		};
+
+		port@28 {
+			ethernet = <&ethernet0>;
+			reg = <28>;
+			phy-mode = "internal";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
new file mode 100644
index 00000000000..59043b2f6f7
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-16g.dts
@@ -0,0 +1,48 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl8382_hpe_1920.dtsi"
+
+/ {
+	compatible = "hpe,1920-16g", "realtek,rtl838x-soc";
+	model = "HPE 1920-16G (JG923A)";
+};
+
+&switch0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		SWITCH_PORT(8, 1, internal)
+		SWITCH_PORT(9, 2, internal)
+		SWITCH_PORT(10, 3, internal)
+		SWITCH_PORT(11, 4, internal)
+		SWITCH_PORT(12, 5, internal)
+		SWITCH_PORT(13, 6, internal)
+		SWITCH_PORT(14, 7, internal)
+		SWITCH_PORT(15, 8, internal)
+
+		SWITCH_PORT(16, 9, qsgmii)
+		SWITCH_PORT(17, 10, qsgmii)
+		SWITCH_PORT(18, 11, qsgmii)
+		SWITCH_PORT(19, 12, qsgmii)
+		SWITCH_PORT(20, 13, qsgmii)
+		SWITCH_PORT(21, 14, qsgmii)
+		SWITCH_PORT(22, 15, qsgmii)
+		SWITCH_PORT(23, 16, qsgmii)
+
+		SWITCH_PORT(24, 17, qsgmii)
+		SWITCH_PORT(25, 18, qsgmii)
+		SWITCH_PORT(26, 19, qsgmii)
+		SWITCH_PORT(27, 20, qsgmii)
+
+		port@28 {
+			ethernet = <&ethernet0>;
+			reg = <28>;
+			phy-mode = "internal";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
new file mode 100644
index 00000000000..61781c708e2
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920-24g.dts
@@ -0,0 +1,68 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl8382_hpe_1920.dtsi"
+
+/ {
+	compatible = "hpe,1920-24g", "realtek,rtl838x-soc";
+	model = "HPE 1920-24G (JG924A)";
+};
+
+&mdio {
+	EXTERNAL_PHY(0)
+	EXTERNAL_PHY(1)
+	EXTERNAL_PHY(2)
+	EXTERNAL_PHY(3)
+	EXTERNAL_PHY(4)
+	EXTERNAL_PHY(5)
+	EXTERNAL_PHY(6)
+	EXTERNAL_PHY(7)
+};
+
+&switch0 {
+	ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		SWITCH_PORT(0, 1, qsgmii)
+		SWITCH_PORT(1, 2, qsgmii)
+		SWITCH_PORT(2, 3, qsgmii)
+		SWITCH_PORT(3, 4, qsgmii)
+		SWITCH_PORT(4, 5, qsgmii)
+		SWITCH_PORT(5, 6, qsgmii)
+		SWITCH_PORT(6, 7, qsgmii)
+		SWITCH_PORT(7, 8, qsgmii)
+
+		SWITCH_PORT(8, 9, internal)
+		SWITCH_PORT(9, 10, internal)
+		SWITCH_PORT(10, 11, internal)
+		SWITCH_PORT(11, 12, internal)
+		SWITCH_PORT(12, 13, internal)
+		SWITCH_PORT(13, 14, internal)
+		SWITCH_PORT(14, 15, internal)
+		SWITCH_PORT(15, 16, internal)
+
+		SWITCH_PORT(16, 17, qsgmii)
+		SWITCH_PORT(17, 18, qsgmii)
+		SWITCH_PORT(18, 19, qsgmii)
+		SWITCH_PORT(19, 20, qsgmii)
+		SWITCH_PORT(20, 21, qsgmii)
+		SWITCH_PORT(21, 22, qsgmii)
+		SWITCH_PORT(22, 23, qsgmii)
+		SWITCH_PORT(23, 24, qsgmii)
+
+		SWITCH_PORT(24, 25, qsgmii)
+		SWITCH_PORT(25, 26, qsgmii)
+		SWITCH_PORT(26, 27, qsgmii)
+		SWITCH_PORT(27, 28, qsgmii)
+
+		port@28 {
+			ethernet = <&ethernet0>;
+			reg = <28>;
+			phy-mode = "internal";
+			fixed-link {
+				speed = <1000>;
+				full-duplex;
+			};
+		};
+	};
+};
diff --git a/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
new file mode 100644
index 00000000000..5368b41c276
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl8382_hpe_1920.dtsi
@@ -0,0 +1,117 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include "rtl838x.dtsi"
+#include "rtl838x_hpe_1920.dtsi"
+
+/ {
+	gpio1: rtl8231-gpio {
+		compatible = "realtek,rtl8231-gpio";
+		#gpio-cells = <2>;
+		gpio-controller;
+		indirect-access-bus-id = <0>;
+	};
+
+	i2c0: i2c-gpio-0 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio1 13 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio1 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	sfp0: sfp-0 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c0>;
+		los-gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 21 GPIO_ACTIVE_LOW>;
+		// tx-fault unconnected
+		// tx-disable connected to RTL8214FC
+	};
+
+	i2c1: i2c-gpio-1 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio1 23 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio1 24 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	sfp1: sfp-1 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c1>;
+		los-gpio = <&gpio1 26 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 25 GPIO_ACTIVE_LOW>;
+		// tx-fault unconnected
+		// tx-disable connected to RTL8214FC
+	};
+
+	i2c2: i2c-gpio-2 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio1 27 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio1 28 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	sfp2: sfp-2 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c2>;
+		los-gpio = <&gpio1 30 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 29 GPIO_ACTIVE_LOW>;
+		// tx-fault unconnected
+		// tx-disable connected to RTL8214FC
+	};
+
+	i2c3: i2c-gpio-3 {
+		compatible = "i2c-gpio";
+		sda-gpios = <&gpio1 31 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&gpio1 32 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+		i2c-gpio,delay-us = <2>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+	};
+
+	sfp3: sfp-3 {
+		compatible = "sff,sfp";
+		i2c-bus = <&i2c3>;
+		los-gpio = <&gpio1 34 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpio = <&gpio1 33 GPIO_ACTIVE_LOW>;
+		// tx-fault unconnected
+		// tx-disable connected to RTL8214FC
+	};
+};
+
+&ethernet0 {
+	mdio: mdio-bus {
+		compatible = "realtek,rtl838x-mdio";
+		regmap = <&ethernet0>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		INTERNAL_PHY(8)
+		INTERNAL_PHY(9)
+		INTERNAL_PHY(10)
+		INTERNAL_PHY(11)
+		INTERNAL_PHY(12)
+		INTERNAL_PHY(13)
+		INTERNAL_PHY(14)
+		INTERNAL_PHY(15)
+
+		EXTERNAL_PHY(16)
+		EXTERNAL_PHY(17)
+		EXTERNAL_PHY(18)
+		EXTERNAL_PHY(19)
+		EXTERNAL_PHY(20)
+		EXTERNAL_PHY(21)
+		EXTERNAL_PHY(22)
+		EXTERNAL_PHY(23)
+
+		EXTERNAL_SFP_PHY_FULL(24, 0)
+		EXTERNAL_SFP_PHY_FULL(25, 1)
+		EXTERNAL_SFP_PHY_FULL(26, 2)
+		EXTERNAL_SFP_PHY_FULL(27, 3)
+	};
+};
diff --git a/target/linux/realtek/dts-5.10/rtl838x.dtsi b/target/linux/realtek/dts-5.10/rtl838x.dtsi
index 11cabc3f63c..41fdbdae20b 100644
--- a/target/linux/realtek/dts-5.10/rtl838x.dtsi
+++ b/target/linux/realtek/dts-5.10/rtl838x.dtsi
@@ -27,6 +27,13 @@
 		reg = <##n>; \
 	};
 
+#define EXTERNAL_SFP_PHY_FULL(n, s) \
+	phy##n: ethernet-phy@##n { \
+		compatible = "ethernet-phy-ieee802.3-c22"; \
+		sfp = <&sfp##s>; \
+		reg = <##n>; \
+	};
+
 #define SWITCH_PORT(n, s, m) \
 	port@##n { \
 		reg = <##n>; \
diff --git a/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
new file mode 100644
index 00000000000..8e29af62bbf
--- /dev/null
+++ b/target/linux/realtek/dts-5.10/rtl838x_hpe_1920.dtsi
@@ -0,0 +1,96 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	chosen {
+		bootargs = "console=ttyS0,38400";
+	};
+
+	memory@0 {
+		device_type = "memory";
+		reg = <0x0 0x8000000>;
+	};
+
+	watchdog1: watchdog {
+		// PT7A7514
+		compatible = "linux,wdt-gpio";
+		gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;
+		hw_algo = "toggle";
+		hw_margin_ms = <1000>;
+		always-running;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinmux_disable_sys_led>;
+	};
+};
+
+&watchdog0 {
+	status = "disabled";
+};
+
+&spi0 {
+	status = "okay";
+
+	flash@0 {
+		compatible = "jedec,spi-nor";
+		reg = <0>;
+		spi-max-frequency = <50000000>;
+		m25p,fast-read;
+
+		partitions {
+			compatible = "fixed-partitions";
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			partition@0 {
+				label = "bootware_basic";
+				reg = <0x0 0x50000>;
+				read-only;
+			};
+
+			partition@0x60000 {
+				label = "bootware_data";
+				reg = <0x60000 0x30000>;
+				read-only;
+			};
+
+			partition@0x90000 {
+				label = "bootware_extend";
+				reg = <0x90000 0x40000>;
+				read-only;
+			};
+
+			partition@0x100000 {
+				label = "bootware_basic_backup";
+				reg = <0x100000 0x50000>;
+				read-only;
+			};
+
+			partition@0x160000 {
+				label = "bootware_data_backup";
+				reg = <0x160000 0x30000>;
+				read-only;
+			};
+
+			partition@0x190000 {
+				label = "bootware_extend_backup";
+				reg = <0x190000 0x40000>;
+				read-only;
+			};
+
+			partition@0x300000 {
+				label = "firmware";
+				compatible = "h3c,vfs-firmware";
+				reg = <0x300000 0x1cf0000>;
+			};
+
+			partition@0x1ff0000 {
+				label = "factory";
+				reg = <0x1ff0000 0x10000>;
+				read-only;
+			};
+		};
+	};
+};
diff --git a/target/linux/realtek/image/Makefile b/target/linux/realtek/image/Makefile
index cf779002e86..6165d99bfc5 100644
--- a/target/linux/realtek/image/Makefile
+++ b/target/linux/realtek/image/Makefile
@@ -8,6 +8,7 @@ KERNEL_ENTRY = 0x80000400
 
 DEVICE_VARS += ZYXEL_VERS DLINK_KERNEL_PART_SIZE
 DEVICE_VARS += CAMEO_KERNEL_PART CAMEO_ROOTFS_PART CAMEO_CUSTOMER_SIGNATURE CAMEO_BOARD_VERSION
+DEVICE_VARS += H3C_PRODUCT_ID H3C_DEVICE_ID
 
 define Build/zyxel-vers
        ( echo VERS;\
@@ -41,6 +42,43 @@ define Build/dlink-headers
         cat $@.kernel_part.hex $@.rootfs_part.hex > $@
 endef
 
+define Build/7z
+	$(STAGING_DIR_HOST)/bin/7zr a $(@).new -t7z -m0=lzma $(@)
+	mv $@.new $@
+endef
+
+define Build/h3c-image
+	$(STAGING_DIR_HOST)/bin/mkh3cimg \
+		-i $(@) \
+		-o $(@).new \
+		-c 7z \
+		-p $(H3C_PRODUCT_ID) \
+		-d $(H3C_DEVICE_ID)
+	mv $@.new $@
+endef
+
+define Build/h3c-vfs
+	$(STAGING_DIR_HOST)/bin/mkh3cvfs \
+		-i $(@) \
+		-o $(@).new \
+		-f openwrt-kernel.bin
+	mv $@.new $@
+endef
+
+define Build/relocate-kernel
+	rm -rf $@.relocate
+	$(CP) ../../generic/image/relocate $@.relocate
+	$(MAKE) -j1 -C $@.relocate KERNEL_ADDR=$(KERNEL_LOADADDR) LZMA_TEXT_START=0x82000000 \
+		CROSS_COMPILE=$(TARGET_CROSS)
+	( \
+		dd if=$@.relocate/loader.bin bs=32 conv=sync && \
+		perl -e '@s = stat("$@"); print pack("N", @s[7])' && \
+		cat "$@" \
+	) > "$@.new"
+	mv "$@.new" "$@"
+	rm -rf $@.relocate
+endef
+
 define Device/Default
   PROFILES = Default
   KERNEL := kernel-bin | append-dtb | gzip | uImage gzip
@@ -52,6 +90,17 @@ define Device/Default
 	check-size | append-metadata
 endef
 
+define Device/hpe_1920
+  DEVICE_VENDOR := HPE
+  IMAGE_SIZE := 29632k
+  BLOCKSIZE := 64k
+  H3C_PRODUCT_ID := 0x3c010501
+  KERNEL := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image | h3c-vfs
+  KERNEL_INITRAMFS := kernel-bin | append-dtb | relocate-kernel | 7z | h3c-image
+  IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs | \
+  	pad-rootfs | check-size | append-metadata
+endef
+
 # "NGE" refers to the uImage magic
 define Device/netgear_nge
   KERNEL := kernel-bin | append-dtb | lzma | uImage lzma
diff --git a/target/linux/realtek/image/rtl838x.mk b/target/linux/realtek/image/rtl838x.mk
index 887f82e385c..60eda5359d2 100644
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -65,6 +65,30 @@ define Device/engenius_ews2910p
 endef
 TARGET_DEVICES += engenius_ews2910p
 
+define Device/hpe_1920-8g
+  $(Device/hpe_1920)
+  SOC := rtl8380
+  DEVICE_MODEL := 1920-8G (JG920A)
+  H3C_DEVICE_ID := 0x00010023
+endef
+TARGET_DEVICES += hpe_1920-8g
+
+define Device/hpe_1920-16g
+  $(Device/hpe_1920)
+  SOC := rtl8382
+  DEVICE_MODEL := 1920-16G (JG923A)
+  H3C_DEVICE_ID := 0x00010026
+endef
+TARGET_DEVICES += hpe_1920-16g
+
+define Device/hpe_1920-24g
+  $(Device/hpe_1920)
+  SOC := rtl8382
+  DEVICE_MODEL := 1920-24G (JG924A)
+  H3C_DEVICE_ID := 0x00010027
+endef
+TARGET_DEVICES += hpe_1920-24g
+
 define Device/inaba_aml2-17gp
   SOC := rtl8382
   IMAGE_SIZE := 13504k
diff --git a/target/linux/realtek/rtl838x/config-5.10 b/target/linux/realtek/rtl838x/config-5.10
index c117fc489a8..9075aa6d3cf 100644
--- a/target/linux/realtek/rtl838x/config-5.10
+++ b/target/linux/realtek/rtl838x/config-5.10
@@ -74,6 +74,8 @@ CONFIG_GPIO_PCA953X=y
 CONFIG_GPIO_PCA953X_IRQ=y
 CONFIG_GPIO_REALTEK_OTTO=y
 CONFIG_GPIO_RTL8231=y
+CONFIG_GPIO_WATCHDOG=y
+# CONFIG_GPIO_WATCHDOG_ARCH_INITCALL is not set
 CONFIG_GRO_CELLS=y
 CONFIG_HANDLE_DOMAIN_IRQ=y
 CONFIG_HARDWARE_WATCHPOINTS=y
@@ -134,6 +136,7 @@ CONFIG_MTD_SPI_NOR=y
 CONFIG_MTD_SPLIT_BRNIMAGE_FW=y
 CONFIG_MTD_SPLIT_EVA_FW=y
 CONFIG_MTD_SPLIT_FIRMWARE=y
+CONFIG_MTD_SPLIT_H3C_VFS=y
 CONFIG_MTD_SPLIT_TPLINK_FW=y
 CONFIG_MTD_SPLIT_UIMAGE_FW=y
 CONFIG_NEED_DMA_MAP_STATE=y